Irrigation And Flood Control Department Tender

Control Valves and delivery manifold: Providing, installation, testing and commissioning of DI control valve viz, 1. 65mm dia Sluice valve (PN 1.6) --- 02 No. 2. 65mm dia NRV (PN 1.6)----04 No. Make: VAG/ TALIS/Sigma flow The job includes cutting of pipe at site and fitting of the above valves as per requirement includes all required fittings viz. 14mm thick flanges, Bends gaskets, nut bolts etc.

Voltage Stabilizer: Providing, installation,testing and commissioning of 75 KVA Voltage Stabilizer with of following specifications: i. Range: 180 V – 415 V ii. Copper wound with adequate insulation and thickness suitable to the duty to be performed. iii. Core should be of cold rolled high silicon steel laminations held together with the help of steel clamps; material should be such that both magnetized currents and the core losses are minimum. The core laminations to be of minimum thickness but of adequate strength. iv. Hysteresis loses to be minimum and temperature not to exceed 700C. v. Air gap to be minimum to avoid Eddy formations for it the coils to be immersed in insulating varnish and dried by suitable means. vi. Voltage regulator switch to be of plate type with copper contact points having six boosting steps. The contacts to be suitable to withstand over loading current at least double the rated current over the considerable period of time. vii. The container to be sufficient to accommodate cores, windings, internal connections, and insulating media. Suitable cooling tubes to be provided along with oil level indicators. The container should be manufactured out of MS sheet of suitable thickness strong enough to withstand stresses produced by jacking and lifting. It should be provided with lifting lugs and should be duly painted form inside and outside. viii. The container at its top to be fitted with porcelain insulators for housing poles. ix. Seven numbers of brass poles to be fitted in the plate, three each for incoming and outgoing poles and one for neutral. The poles to be marked. The creapage distance between the poles to be sufficient enough to accommodate the required size tube terminals to prevent arcing. x. The top of the container to have a display panel for housing 02 numbers voltmeters 0- 500V, square dial flush type along with 4 way selector switch and set of neon indicators. xi. Insulating media (T. Oil) of 11 KVA grade to be provided and filled with dielectric strength of 5 KV at 4m air gap. xii. Steel Castor wheels to be fitted to the container at the bottom for easy positioning of the stabilizer. Rating of stabilizer: 75 KVA The job shall also include providing and fitting of suitable copper terminals dully crimped and taped to the incoming and outgoing cables. (The Voltage stabilizer to be manufactured in a registered workshop in presence of person authorized by the undersigned). The T-Oil of specific grade should be provided in a separate barrel.

Servo Stabilizer: Cooling Oil Cooled (Servo Stabilizer) Capacity 100 KVA Input Voltage 160-480 Volts (Phase to Phase) 90-270 Volts (Phase to Neutral) Output Voltage 400 Volts ± 1% (Phase to Phase) 230 Volts ± 1% (Phase to Neutral) Type Suitable for: 100% Balance Load 100% unbalanced Supply Application Indoor Type Standard IS 2026 & IS 9815 Phase 3-Ph, 4 Wires Ingress Protection IP 55 Frequency 50 Hz Wave Form Distortion Nil (Negligible) Response Time Instantaneous (mili sec.) Speed of Correction 20 to 60 V/sec (as required) Mode Of Operation Automatic/Manual Suitability Suitable for all Power Factors. Duty Cycle Continuous 24 Hrs. Efficiency More than 98% Losses at No Load 0.4% of the total capacity Losses at Full load 1.9% at full load. Temp. Rise 45°C Deg.Cent. Above Ambient. Laminations Used Imported Low Losses CRGO Laminations - M4 Grade. Copper Used “Sterlite” Make- 99.9% Pure Electrolytic Grade. Carbon Brushes Used Imported High Grade Graphite Class of Insulation Class - A, Greater than 6M ohms Break Down Strength 2500v AC for 1 minutes (for Transformer) Construction The unit will comprise of 3 Nos. Individual Single Phase Unitsof 1/3rd of the total capacity connected in star configuration. Further, each of the three phases will further comprise of following: In Each Phase In Complete Servo 1 No. Digital Micro Controlled Processor Based Control Card with elegant push buttons for operations. 3 No’s 1 No. AC Synchronous Servo Motor 3 No’s 1 No. Copper Wound motorized variable auto transformer, wound on toroidal CRGO laminations with High quality graphite carbons for smooth functioning. 3 No’s 1 No. Buck n Boost series transformer. 3 No’s General Arrangements: All the above will be incorporated inside high quality epoxy painted sheet steel tank fitted with cooling radiators and mounted on unit-directional wheels, other fittings would include as follows Lifting Lugs Earthing Terminals – 2 No’s Oil filling valve Oil Level Indicators Rating Plate Name Plate Terminal Arrangement: Cable box suitable for Input & Output armoured cables of appropriate rating. Suitable Aluminium bus bars/terminals will be provided. with stem type terminals For auxiliary connections. Protections The Servo Voltage stabilizer must be fitted with the following protection devices. Over voltage Protection trip. Under voltage trip. Time delayed operation Overload trip Short Circuit protection. Single Phase Protection. Phase reversal Protection. The job includes providing/ installation/ testing and commissioning of 200 A Change over switch for connecting the Stabilizers. The specifications of the Change over switch are as follows: The job includes Providing, Installation, testing and commissioning of 3 phase, 200A, manually operated changeover switch. The job shall include proper thimbling of the terminals of the conductor as input to the equipment and the outgoing copper terminals from the switch of desired specifications at site. The other broad band specifications of the changeover switch are given as under: a. Type: Manual Changeover in Sheet Steel Enclosure b. No. of poles: 4 c. Rated Voltage: 415V d. Rated Current: 200 Original Manufacturer’s Test certificates in original to be provided with the material before installation.

Sub Station: The construction of Sub Station includes: i. Providing and erecting of four numbers of steel tubular poles 9m (SP33, ISI mark HTL-IS 1161 or IS-2713) with base plate 350mmx350mmx5mm long as per the latest IEE rules for fabricating 04 pole structure (with 2 NO. 9m SP33 poles and 02 No. 150mm dia 8mm thick pipes cut to adjust the height of the station bed as per site engineers instructions. ii. Fabrication, providing and fitting of ISMC-100 (as per the drawing attached). iii. Providing, fabrication and fitting of ISMC-150 pieces 8 feet long each 12 Nos. complete with nuts and bolts and clamps as per requirement for resting of HT transformer also includes providing and fixing of 8’x8’ chequered plate 6mm thick over the channels fixed with nuts and bolts. The job includes earthwork and concrete bottoming of sub-station as per requirement of site. iv. Providing and fitting of lightening arrestor (Heavy duty, POST type). v. Providing and fitting of set of drop out fuse set/ link set (2 Nos) (G.O.D) heavy duty providing and fixing of set of HT insulator. vi. P/Fixing of disc insulators set. vii. Providing and installation of cable termination kits and thimblings as per site requirement. viii. Providing and fixing of anti-climbing devices. ix. Other items like danger plates. The job includes providing/applying of metallic primer coat and two coats of enamel paint. Complete earthing of sub-station as per IEE rules. (Chemical earthing 3 Nos as per requirement and directions of in charge Engineer to accessories of sub-station) x. Manufacturing, installation and commission of , 100KVA (2 Nos One as Standby), oil cooled three phase, outdoor type 11/0.433 KVA conventional (non-seated) type distribution, transformer shall have core type construction, suitable for outdoor system as stop down transformer. The primary winding shall be connected in the delta and secondary winding in star with symbol (DYLL). The neutral of separate insulated terminal. The core shall be built up of high grade chrome annealed silicon steel laminators having low loss and coated with firmly with channeled frame to prevent noise and vibrations. The LV winding shall be circular and concentric with HV winding on the outside. The arrangement of winding should be robust in elect./ mechanical construction and should permit free circulation of oil to avoid hot spots. Adequate bracing shell be provided so that a strong self-supporting coils is obtained, no tapes shall be provided in the Winding Electrical grade epoxy dotted or other suitable insulations both for LV and HV windings. The transformer tank shall be made out of MS Sheet of minimum thickness 3.15mm thickness for sides and 5m thicknesses for top and bottom plate, suitable to withstand extreme pressure conditions. Primary coating and two coats of enamel paint should be duly painted on the tank. The transformer shall have a conservator tank provided with a drain plum-filling hole with cover. The cover shall be with 75x49 mm channel, with holes to make them suitable for mounting on plate/ plinth. The transformer tank shall be fitted with new 11 KVA grade T oil up to specific mark, the earthing terminals, two lifting lungs, rating and terminal marking plate, bi-metallic terminal connection for High Voltage/ Low V voltage side bushing level gauge, breather, duly valve should be provided to the transformer. Original Manufacturer’s Test certificates in original to be provided with the material before installation. Note:- The Electrical connection from the concerned PDD Department should be done by the firm in all respects.

HT POLES Providing and Errection of 9 Mtrs long M S Tubular poles having reducing dia of 6’’x 5’’ x 4’’ from bottom to top. The job includes P/F of 5 feet long cross arm ISMC-75, cross brace 1m x 40mmx 5mm, 3 no. HT insulators with pins to each pole. The job also includes spiral earthing, painting of poles in silver colour, grouting of poles in CC blocks of (1:1 ½:3) mix, P/F of danger plate indicating (11000V-DANGER) & P/F of nuts and bolts of assorted size. The job also includes P/F of 8` long ISMC-75 Chanels 3 Nos at the tapping point with three No HT Insulaters.

LT CONDUCTOR P/Laying of aluminum conductor 0.05 ACSR with all head loads and lifts etc

Control Panel Fabrication providing and fitting of Modular control panel of Appropriate size fabricated out of 16 SWG sheet having required openings/vents and protection class: IP 55 and fitted with accessories as under:- a) Incomer = 250 A (MCCB) Qnty = 1 No Make = L&T / Siemens/ABB No of poles = 4 Rated operational voltage = 415V ± 15% Rated Frequency = 50± 3% Hz Ambient temperature = 40 deg c Ultimate S.C circuit Breaking capacity At (425 AC 50 HZ = 36 kA Thermal release range = 125-160 A b) Change over switch Make = L&T/Siemens/ABB Qnty = One No Type = CO2-125 4 pole Rating = 125A c) Distribution Bus Bar Electrical grade Al with red, Blue and yellow tapping of Adequate section. Rating = 200 A d) Circuit Breaker = 100 A (MCCB) Qnty = 2Nos Make = L&T / Siemens/ABB No of poles = 3 Rated operational voltage = 415V ± 15% Rated Frequency = 50± 3% Hz Ambient temperature = 40 deg c Ultimate S.C circuit Breaking capacity At (425 AC 50 HZ = 36 kA Thermal release range = 100-125 A e) Auxiliary circuit Breaker = 100 A (MCCB) Qnty = 1 No Make = L&T / Siemens No of poles = 4 Rated operational voltage = 415V ± 15% Rated Frequency = 50± 3% Hz Ambient temperature = 40 deg c Ultimate S.C circuit Breaking capacity At (425 AC 50 HZ = 36 kA Thermal release range = 80-100 A On-off switches = 5 Nos (16 A) Copper strips = 4 Nos (3 Nos for three phases and one No for Neutral) f) Starters Make = L&T Rating = MU-G40 Power Specs = 3 phase, 425 ± 15 % Qantity = 2nos g) Ampere meter Size = 96mm Sq Range = 0-50 A Make = L&T/Rishab CT coils = Requisite 5 VA - 10 VA capacity 7 CT ratio CT coil per meter = 2Nos (L&T) Type = Analogoue Qnty = 1 No (In Bus Bar Chamber) with selector Switch h) Voltmeter Size = 96mm Sq Range = 0-500 Volts Make = L&T/Rishab Type = Analogous Qnty = 1 No (In Bus Bar Chamber) With Selector Switch I) Frequency meter Qnty = 1 No (In Bus Bar Chamber) Frequency meter = 0-50Hz Type = Analogues Make = L&T/Rishab/AE J) Power factor meter Qnty = 01 Nos Type = Analogues Make = L&T/Siemens/ABB k) Neon Indicators Qnty = 3 Nos 1 No (In Bus Bar Chamber) The modular control panel shall have the dimensions and cabins as detailed in the enclosed drawings. The enclose shall be of excellent fit and finish, corrosion resistant treated and powder coated gliding hinges for smooth and noiseless movement. All the electrical joints in the panel shall be fitted with Belleville washers. Original Manufacturer’s test certificates in original to be provided for all the accessories/ items required for Control Panel before its installation.

Distribution Cables: Providing, Installation, testing of multi-stranded copper conductor PVC insulated single core unsheathed 35mm sq. Copper cable for internal distribution wiring. The multi-stranded copper cable to be laid through PVC conduits on wooden plain boards fixed on walls with suitable plugs, nails and clamps. The job also includes termination of ends of cable with suitable rating of Cu. thimbles duly taped.Original Manufacturer’s Test certificates in original to be provided with the material before installation. Make: Havells/ National/Standard/Plaza/Imperial/ RR Kables.

Service Cables: Providing, laying, installation and testing of 3.5 Core, 95 sq. mm. Aluminum Conductor, PVC insulated, armored cable from distribution box of Transformer to the voltage stabilizer at both stages of the scheme. Job also includes providing and installation of aluminum Thimblings of appropriate ratings (24 No.) duly crimped and taped.Original Manufacturer’s Test certificates in original to be provided with the material before installation. Make: Havells/ Polycab/ Finolex/RR Kables

Motor cables: Providing, laying and testing of flat 3 core copper 16 sq mm submersible cable. The cable shall be PVC insulated and impermeable to grease, water and abrasion resistant. The job includes providing of copper thimblings as per requirements. Original Manufacturer’s Test certificates in original to be provided with the material before installation. Make: Finolex/ Polycab/ Havells

Gantry: Over Head Gantry Fabrication / Erection of Channel iron column to act as support for resting of monorail crane as per following details:- Vertical Posts = ISMC 150 No. of vertical posts = 02 Nos. Vertical channel section each post = 02 Nos. vertical post bracing = ISMC 100 Sole / Matching plates = 500x300x12 mm Height of vertical posts = 4.5 M size of vertical post concrete blocks = 600x600x900mm Concrete grade = M20 welding Electrode = Overcord SS of Adore/ESAB/L&T Monorail Section = ISMB 200 length of monorail = 5M Steel Detail : i. ISMC 150 6Mx2x2 = 24 M @ 16.4kg/m = 393.6 kg ii ISMC 100 0.25Mx10x2x2 = 10 M @ 9.2kg/m = 92 kg iii Plate 0.500x0.300x8 (12mmthk) = 1.20 M²(12thk) = 112.80 kg iv Monorail ISMB 200 5 M @ 25.4 kg/M = 127kgs v Bolts/Nuts (L.S) = 20 kgs Total = 745.4 kg = 750 KG say Supply, Installation of 3 ton capacity motorised chain hoist with hook suspension having following specifications:- Make = INDEF (HERCULES BABY-KEH) Capacity = 3 ton Hoisting speed = 2.4 M/Min Hoist motor H.P = as per requirement No. Of chain falls = 4 Min. Height of lift = 3 M MONORAIL = As per requirment Note:- All descriptive data given above is approximate, intended to give general idea of the product. The equipment be supplied as per the latest parameters / specifications. The chain hoist shall also have the following characteristics:- 1. Motor:- The basic drive of the hoist be provided with 3 phase squired cage totally enclosed induction motor having a high starting torque with class “F” insulation. The make of the motor be NGEF / SEIMNS / GEC/ Crompton and conform to IS : 325 (RPM-1500) 2. Brake:- The hoist shall have instant action, Fail to safe electromagnetic disc brake mounted on the end of the motor to ensure minimum safety and reliability when the load is held in its position as soon as the supply to the motor is switched off internally or accidentally. The adjustment & maintenance of break shall be quick and simple. 3. Gears:- The hoist shall have precision cut super and helical gears made of alloy steel mounted on bearings and housed in a dust proof gear box. The lubrication of gears be of high viscosity and temperature for longer life of gears. 4. Load Chain:- The load chain be made of high tensile alloy steel having wear resistance and greatest mobility. The chain should be accurately collaborated, tested and have adequate in built factor of safety for safer operation. 5. Load chain wheel:- Specially designed, perfectly machined wheel providing correct grip of load chain made of malleable cast iron makes the hoist most safe and reliable against any failure. 6. Lifting Hook:- The lifting hook shall be forged with provision for free swivelling. 7. Limit Switch :- The limit switch shall have snap action, shunt type prevent over hoisting or over lowering to ensure maximum safety of operation. 8. Control:- The unit shall be controlled by heavy duty air break direction reversing type contractors and electrically inter – locked for safety. Contactors relay, fuses, low voltage transformer be fitted for control voltage and are to be housed in fabricated / pressed sheet steel box dust proof. 9. Push button pendent:- The contactors shall be operated by a pendent push button station suspended from hoist by a rope / dog chain to prevent any damage to the pendent cable and for easy operation. Test:- The hoist supplied is to be tested at 25% overload and the test certificate of the same be provided at the time of installation. The complete unit as specified above is required to be fitted / tested at site. Complete painting of fabricated structure by way of applying of two coats of red oxide as primer and then painting with enamel paint of any shade with two coats (powder coated).

Illumination and other amenities: -Providing, manufacturing, installation and fitting of heat resistant toughened glass 60W LED street lights (02 Nos.) with following specifications: Power Consumption/ Rating = 60W Make = Havells/ Vinay/ Bajaj/ Syska Housing/ Bogy = Single piece Pr. Die cast Aluminum Alloy complete non dimmable, environmental friendly, weather proof, excellent aesthetics. Operating voltage = 140- 270V, 50Hz The street lights to be fixed on the galvanized steel poles (02 nos to be provided), octagonal type 8m each complete with required MCB (02 nos.) of 10 amperes, required cable of 1.5mm2 (copper wire multi stranded type) from MCB to light through PVC conduits. The MCBs to be housed in MS boxes. The steel poles to be provided with 2 MS arms for each pols for housing street lights. The job also includes providing, installation, fitting and testing of 40W LED lights (01 No.) with heat resistant toughened glass with following specifications: Power Consumption/ Rating = 40W Make = Havells/ Vinay/ Bajaj/ Syska Housing/ Bogy = Single piece Pr. Die cast Aluminum Alloy complete non dimmable, environmental friendly, weather proof, excellent aesthetics. Operating voltage = 140- 270V, 50Hz The job also includes providing and fitting of MCB of 10 amperes, required cable of 1.5mm2 (copper wire multi stranded type) from MCB to light through PVC conduits. The job also includes providing and installation of 5 No. 12 Watt LED Lamps along with holders and switches and fitting by providing 1.5 sq. mm copper wire as per site requirement. Providing and installation of 16 A sockets along with 4 sq mm copper wire as per site requirements. All wires, to be laid through double U channels along with clamps, screws and other accessories. -Providing and fitting of inverter cum battery (180AH) with 5 No inverter lumps with all accessories like wire holder, channels ,switches and lumps. -Providing of solar/ electrical lantern both chargeable in solar/electrical (Indus/Tata) (01 No.). -Providing of bedding including mattress, pillows, blankets and utensils as amenities to the pumping station staff as per requirements. Providing of tool kit consist of following items  Spanner set = 12 pieces of size 4/5,6/7,8/9,10/11,12/13,14/15,16/17,18/19, 21/23,24/26,24/27,30/32  Ring set = 12 pieces of same size as above  Pliers = 2 No`s (tappari/ jalani)  Cutting pliers = 2 No`s(tappari/jalani)  Screw driver = 2 No`s (tappari/jalani)  Hammer = 1 no of size 1 kg  Pipe wrench = 2 Nos of size 12 inches Mutimeter = 1 No L Keys = one complete set

Earthing: Chemical Earthing of all the electrical equipment’s like transformer, lightening arrestor, sub-station using Electrode as per load, 2 Meters long connected with desired sized Aluminum internal strip complete with excavation, civil works, cast iron cover with back fill compound as required. The said earthing pit shall be completed taking into account the load of the equipment’s installed at site in consideration, included is installation of required sized Aluminum strips from earthing station to all the installed equipment’s with all desired items required.

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed: All kinds of soil

Ordinary Rock

Earth work in bulk excavation by manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge. All kinds of soil

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:

Extra for every additional lift of 1.5 m or part thereof in excavation/banking excavated or stacked material : All kinds of soil :

Supplying and stacking at site, Graded crushed stone aggregate of size, 90 mm to 45 mm with Stone screening of size, 13.2 mm and 11.2 mm nominal size (Type A), including laying of stone dust / Moorum as binding material including laying of water bound macadam sub-base with brick aggregate and binding material, earth etc. including screening, sorting, spreading to template and consolidation with power road roller 8-10 tonne capacity etc. complete inclusive of all carriages upto site of work complete job

Random Rubble masonry with hard stone in foundation and plinth including leveling up with cement concrete 1:6:12 (1 Cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level and curing complete with: Cement mortar 1:6 (1 Cement : 6 coarse sand)

Dry random rubble masonry with hard stone in foundation and plinth: With bond stone

Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes, manually/by mechanical means including stacking of pipes within 50 meters lead as per direction of Engineer-in-charge : 15 mm to 40 mm nominal bore

Above 40 mm nominal bore

Providing G.I. pipes complete with G.I. fittings Medium weight class B excluding trenching and refilling etc. (external work)incld. Carraige by mechanical means :-100mm dia G.I pipe

100mm dia class A light weight conforming to IS: 1239 part ist

80mm dia class A light weight conforming to IS: 1239 part ist

Providing and fixing G.I. pipes complete with G.I. fittings light weight class A excluding trenching and refilling etc. (external work) conforming to IS: 1239 part ist incld carraige by mechanical means:-50mm dia G.I pipe

40mm dia G.I pipe

25mm dia G.I pipe

20mm dia G.I pipe

15mm dia G.I pipe

Laying and fitting of G.I. pipes (all classes) complete excluding cost of pipes, fittings and Earth work:- 50mm dia G.I pipe

40mm dia G.I pipe

25mm dia G.I pipe

Providing and fixing of 14mm thick M.S flanges G.I pipe incld. Cost of flanges, rubber gaskets, nuts bolts, welding charges cutting of threads excld. Earth work and refilling: 100mm dia

Providing and fixing of 12mm thick M.S flanges G.I pipe incld. Cost of flanges, rubber gaskets, nuts bolts, welding charges cutting of threads excld. Earth work and refilling: 100mm dia

80mm dia

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions incld. Tailpeices ,tapers, Gi pipe etc. complete 50mm dia

25mm dia

100mm dia Non Return Valve

Providing and fixing of CI sluice valve with cap including all accessories like nuts, bolts rubber insertion etc and tail pieces of Kirloskar make including successful testing and commissioning. 100mm dia

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing Tee, including cutting and threading the pipe etc. complete 25 to 40 mm nominal bore

50 to 80 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) 50 mm nominal bore

65 mm nominal bore

Constructing masonry Chamber of specified size, in brick work with common burnt clay (non modular) bricks of class designation 7.5 incement mortar 1:4 (1cement :4 coarse sand) and R.C.C. top slab 1:1.5:3mix (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mmnominal size ) including necessary xcavation, foundation concrete1:5:10 (1 cement :5 fine sand : 10 graded stone aggregate 40 mmnominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design. For sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid. Chamber 120x120x100 cm

Dumping stone including cost of stones. in Horizontal on level

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m

Providing & laying stone soling in horizontal on level.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level: 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with : 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in arches, archribs, domes, vaults shells, folded plate and roofs having slope more than 15° upto floor five level level including curing but excluding the cost of centering, shuttering finishing and reinforcement with:- 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Providing & fixing of main hole cover 0.75 x 0.75 of standard quality with angle iron frame incld all necessary fittings complete

Providing & fixing of main hole cover 0.90 x 0.90 of standard quality with angle iron frame incld all necessary fittings complete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level: Thermo-Mechanically Treated bars of grade Fe-500D or more

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete Welded

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platforms

Lintel, beams, plinth beams, girders, bressumers and cantilevers

Arches, domes, vaults upto 6 m span

Extra for shuttering in circular work

Extra for shuttering in circular work: foundation

Extra for shuttering in circular work: Lintels/beams

Extra for shuttering in circular work: Lintels/beams

Extra for shuttering in circular work: suspended floors

Edges of slabs and breaks in floors and walls : Under 20 cm wide

Columns, pillars, piers, abutments, posts and struts.

Providing and fixing of 50mm dia G.I half bend of standard quality to be fixed in dome for aeration purpose

Providing and incorporating PGI sheets strips 0.8mm thick at construction joints incld. All carriages complete job

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

12mm Cement plaster finished with a floating coat of neat cement of mix:1:3 (1 cement 3 sand)

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-incharge. Made of G.I. wire of dia 4 mm

12mm Cement plaster of mix: 1 : 4 ( 1 cement : 4 fine sand)

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness)including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses,string or lacing courses, parapets, coping, bed blocks, anchors blocks, plain window sills, fillets etc upto floor V level, including curing but excluding the cost of centring, shutteringand finishing with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Supply and filling GSB (granular sub-base) in layer not exceeding 22cm in thickness & aggregate size does not exceed 90mm incld. carriage

Providing & laying damp-proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone agg 12.5 mm nominal size) and curing complete

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete. 50 mm thick with 20mm nominal size stone aggregate

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length hold fast lugs or with dash fasteners shall be paid for separately): Second class kail wood

Providing and fixing glazed shutters for , windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). First class kail wood (35mm)

Providing and fixing of 4mm thick Float glass panes(weighing not less than 10 kg/sqm

Providing and fixing fly proof wire gauze to windows, clerestory windows and doors with M.S Flat 15x3 mm and nuts and bolts complete. Galvanized M.S wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Providing hoisting and fixing trusses/purlins /rafters/posts/ post-plates or like components including cost of screws etc. complete Second class Kail wood

Providing and fixing of panneled 40mm thick doors of of first class kail wood incld all sorts of carraige complete

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gram/m2

Providing & fixing colour corrigated ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gram/m2

Providing and fixing plained eaves boarding (Kail wood). 250x32 mm (nominal size )

Providing and fixing of Gsheet soffit of approved quality , colour and texture complete

providing & fixing of Anchor bolts of 16mm dia 9"long

Providing and fixing of of Hardware items Aldrops 150mm dia

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: Tower bolt ( 150x10 mm ) long

Tower bolt ( 100x10 mm ) long

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 125mm

100 mm

Air hooks

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. ( 2 mm thick )

Finishing with Deluxe multi surface paint system for interiors and exteriors using primer as per manufacturers’ specifications: Painting wood work with deluxe multi surface paint of required shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.75litre/10sqm of approved brand and manufacture

Providing and fixing of GI pipes complete with G.I fittings & clamps incld. cutting & making good etc complete

Providing and fixing of pvc pipes, cables with all pvc fittings incld. trenching and refilling etc (external with flateral 100mm dia pvc pipe) along with bends, sockets etc (prince quality)

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content. With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ liter

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work

Providing & fixing White vitreous china water closet squatting pan(Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge Long pattern W.C Pan of size 580x440 mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank lSI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including all associated fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid lSI license]

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (wall / floor tiles)

Providing & fixing of stainless steel sink incls waste pipe

Providing and fixing of electric and heating points including wiring for lightning points in 1.5 sq. mm, PVC insulated copper wire and 2.5 sq. mm PVC insulated multi strand copper wire, 6mm one way switches, 2 mm thick PVC conduit/ channel with bends, junction boxes etc 6amp S pole MCS, 10 Amp DP MCB, 2 way for housing MCB, hylan sheet with wooden box recessed in walls with accessories complete: Lighting point

Heating point

Fan with dimmer

Exhuast Fan 12" x12"

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength confirming to IS:4454 part-1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Applying priming coat:- With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel work (second coat)

Painting with aluminum paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing and mixing of water proofing material or equivalent for RCC work

Providing and fixing of nuts ,bolts and chips incld one end fix to anchor block

Providing and fixing of PVC pipes for aeration purposes

Welding, including transportation of plant at site etc. complete By electric plant

provision for temporary diversion of water

Providing and fitting of 1 No. water Gysers, 2 No. water mixers. 4 No. Bibcock s, Mirrors, Jugs/ mugs & other bathroom accessories etc

Providing and fitting of bedroom items Floor mating, 01 No. beds with necessary beding and mattresses , 01 no. wardrobes for cloths, 1 no. locker, 4 chairs and one table, Utensils gas with gas stove etc

Provision for Providing and fixing of pipe specials of standard quality incld. testing complete

Carraige of materials from source to road site of work including loading , unloading and stacking:-- Stone / stone soling for an av lead of 15 km

40mm aggregate for an av lead of 35 km

20mm aggregate for an av lead of 35 km

sand for an av lead of 35km

cement for an av lead of 10 km

steel for an av lead of 10 km

Bricks for an av lead of 80 km

Carraige of materials from road site to site of work by manual labour including loading , unloading and stacking for an av lead of 300 Mtrs. Stone / stone soling

40mm aggregate

20mm aggregate

sand

Cement

Steel

Bricks

100mm dia GI pipes for an av lead of 500 mtr

Providing, erecting and fixing of sign board 2'6''x4' made up of angle iron frame work 50x50x6mm with 1mm thick M.S sheet including priming, painting and proper lettering and embeding with 1:3:6 cement concrete complete job