Irrigation And Flood Control Department Tender

Fabrication of MS canopy cum gantry at Lift Irrigation Scheme hanjishat by way of: A. Erection of MS vertical column out of 100mm dia 4.5 mm thick MS structural pipe each having length of approx 16 feet×06 no= 30m@ 12.2kg/m= 366 kg B. Providing and fitting of horizontal structure out of ISMC ISA 50*50*05mm approx 10 feet each × 04 no= 12m@3.8 kg/m =45.6kg C. Prividing and fitting of Horizontal member for gantry out of ISMB 200 approx 12 feet long×01 no= 3.65m=88.83kg D. Fabrication of howe double truss having sloping angle of 30 degree out of ISA 40*40*05mm as per instruction of site engineer each having weight of approx.32 kg×06 no= 192 kg E.Providing and fitting of purlins out of ISA 40*40*05mm approx 12 feet long×08 no= 87.60kg F. Providing and fitting of MS plate to vertical colums, gusset plate out 08mm thick MS plate----------- 50 kg Total weight of MS used= 830kg approx

Providing and fitting of 0.63mm thick CGI sheets on the roof of the MS shed with zinc coating not less than 275gram/sqm. The job includes providing with polymer coated J and L hooks,bolts and nuts and G.I limped washers. including a cost of approved steel primer and two coats of approved paint on overlaping of sheets complete excluding the cost of purlin,rafters and trusses but including the cost of cutting.

providing ridge or hip of width 60 cm plain GS sheet with with polymer coated J and L hooks,bolts and nuts and G.I limpet and bitumen washers 0.63 mm thick with zinc coating not less than 275gram/sqm .

Earthwork in excavation by manual means in foundation of trenches for all kinds of soil with required depth including removal of excavated soil,dressing of bed and sides ,dewatering of trenches if any and disposal of excavated soil as directed by engineer incharge all leads.

Refitting of existing usable ISA for fabrication of side walls of canopy and strenghthening structure as per site requirement as per directions of site incharge.

Fitting of existing usable CGI sheets on side walls of MS Canopy. The job includes providing with polymer coated J and L hooks,bolts and nuts and G.I limped washers. including a cost of approved steel primer and two coats of approved paint on overlaping of sheets complete excluding the cost of purlin,rafters and trusses but including the cost of cutting.

Providing and laying stone soiling tightly hand packed under foundation footing etc. including ramming and dressing and carriage of material from source to site of work complete in all respect.

Providing and laying in position cement concrete of grade 1:4:8(1 cement,4 coarse sand,8 graded stone agg/40mm nominal size crushed agg).

Providing and laying in position cement concrete of grade 1:2:4 (1 cement,2 coarse sand,4 graded stone agg/20mm nominal size crushed agg).

Illumination of pump house by way of providing and fitting of a.providing installtion and testing of die cast Alumimium flood lights LED with IP 65 rating of 20 Watt (08 no).Providing and fitting of 1.5 mm2 Cu wire (120m), Providing and fitting of PVC conduit (50m), Providing and fitting of 02 no. separate 6-32A DP MCB 240 V 50 Hz control switch for indoor and outdoor lighting. Providing and fitting of 6A 3 pin socket (02 no.), 240 V 50 HZ Make: Anchor, SSK or equivalent. The job includes cost on account of charges for skilled electrician and labour.

Fabrication & providing of MS operator sleeping beds (6 feet x 8 feet) by way of cutting and electric arc welding of mild steel angle ISA-40x40x5 with height of 4 feet and each end length to be fitted with gusset plates of suitable size specifications Total length of ISA-40x40x5= 19mtrs@3kg/m= 57kgs Job includes fitting of 6’ X 8’ ply board (19 mm Thick ) to bed and applying of two coats of red oxide primer and two coats of enamel paint and then shifting of same to site after its fabrication at workshop. The Job also includes providing and fitting of Thermocol and excel matting for bed.

providing and fitting of 03 ton capacity heavy duty chain pulley block with a lift height of 06m make pull lift/Indef/reputed make

Fabrication, providing and fitting of bypass arrangement to the 300 mm dia MS rising main out 80 mm dia MS pipe approx.06 feet long. Job includes fabrication of bends (02 no), providing/fitting PN 1.0 80 mm dia CI gate valve(01 no), providing/fitting of 100 mm MS flanges (02 no), washers (02 no), nut bolts.

Finishing with epoxy paint (two or more coats) at all loactions prepared and applied as per manufacturers specifications including appropriate priming coat, preparation of surface etc.on steel work.

providing and fitting of Double ended spanner (06 to 32)-----01 set, Double ended chrome plated ring spanner set(06 to 32)----01 set, providing and fitting of450 cc heavy duty grease gun lever type (01 no), 11 KVA rubber safety glove pair (01 no), 03 ton capacity sling sling belt (02 no), plier (01 no), screw driver set(01 no) (Taparia or equivalent reputed make)

shifting of old scrap material (if any) from site to stores subdivision Baramulla approx. lead 30 km in load carrier.