Indo Tibetan Border Police Tender

Supply of Power make LT Switch Board with rupturing capacity of MVA at 415 Volts (type test done at CPRI BHOPAL) fully accessible form the front suitable for 3 phase “4 wire, 50 cycles A.C. supply weather proof, vermin proof, ventilated, front operated, floor mounting panel with compartments front cubical design, modular construction, fully compartmentalized, Indoor, Floor/Wall Mounted made out from 2/1.6 mm thick CRCA sheet A Panel duly painted with Powder Coated. General SpecificationsThe breaking capacity of ACB & MCCB as per electricity load . Electric Grade Aluminum bus bar with maximum current density of 1 amp. / Sq mm. suitable for 3 phase 4 wire 415 volt 50 Hz balanced/ unbalanced power system conforming to specifications.” The Bill of material/ component as per single line diagram. Metering set with all incoming Feeders on as per requirement. Panel are approved and successfully tested at 50 K.A. Breaking capacity of Bus bar 4000 A at C.P.R.I. Bhopal. Sheet steel Enclosure 2/1.6mm. C.R.C.A. sheet and Base frame of panel Board 75 x 40 x 3 mm. Nut, Bolt, washer shall be cadmium plated. Fully Compartmentalized. Gasket in all doors. Earthing with continousaluminum flat. Minimum clearance shall be maintained. Height of the panel as per site. Bill of material as per engineer-in charge drawing and specification. Makes of equipments& colour shade of panel board as per engineer-in-charge .asas per engineer-in-charge. PANEL :-Panel will be fabricated with 03 mm CRCA sheet steel for load bearing surfaces and 02 mm CRCA sheet steel for non load bearing surfaces with 3 mm gland plates. Paint shade is RAL 7032 , Cable entry in botttem , outdoor panel type ,floor mounted with MS angle 50x50xx6mm.BUS BAR :-600A Aluminium main bus bar , load wise sub feeder bus bar colour coated heat shrink bus bar sleeve nut -bolt, washer , hardware etc. INCOMER:- 01 No MCCB 400A FP 36 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB), 03 Nos R Y & B Phase indicating Lamps, 01 No Digital Amperemeter , 01 No Digital Voltmeter , 03 Nos 400/5A CI-1 15VA current transformer, 03 Nos MCB 6A 10KA SP , 06 Nos CT shorting Links & 01 No Netural Links. OUT GOING :-03 Nos MCCB 200A FP 10 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB) , 02 No MCCB 100A FP 10 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB) , 01 No MCCB 63A FP 10 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB)

Supply of Power make LT Switch Board with rupturing capacity of MVA at 415 Volts (type test done at CPRI BHOPAL) fully accessible form the front suitable for 3 phase “4 wire, 50 cycles A.C. supply weather proof, vermin proof, ventilated, front operated, floor mounting panel with compartments front cubical design, modular construction, fully compartmentalized, Indoor, Floor/Wall Mounted made out from 2/1.6 mm thick CRCA sheet A Panel duly painted with Powder Coated. General SpecificationsThe breaking capacity of ACB & MCCB as per electricity load . Electric Grade Aluminum bus bar with maximum current density of 1 amp. / Sq mm. suitable for 3 phase 4 wire 415 volt 50 Hz balanced/ unbalanced power system conforming to specifications.” The Bill of material/ component as per single line diagram. Metering set with all incoming Feeders on as per requirement. Panel are approved and successfully tested at 50 K.A. Breaking capacity of Bus bar 4000 A at C.P.R.I. Bhopal. Sheet steel Enclosure 2/1.6mm. C.R.C.A. sheet and Base frame of panel Board 75 x 40 x 3 mm. Nut, Bolt, washer shall be cadmium plated. Fully Compartmentalized. Gasket in all doors. Earthing with continousaluminum flat. Minimum clearance shall be maintained. Height of the panel as per site. Bill of material as per engineer-in charge drawing and specification. Makes of equipments& colour shade of panel board as per engineer-in-charge .asas per engineer-in-charge. PANEL :-Panel will be fabricated with 03 mm CRCA sheet steel for load bearing surfaces and 02 mm CRCA sheet steel for non load bearing surfaces with 3 mm gland plates. Paint shade is RAL 7032 , Cable entry in botttem , outdoor panel type ,floor mounted with MS angle 50x50xx6mm.BUS BAR :-600A Aluminium main bus bar , load wise sub feeder bus bar colour coated heat shrink bus bar sleeve nut -bolt, washer , hardware etc. INCOMER:- 01 No MCCB 200A FP 36 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB), 03 Nos R Y & B Phase indicating Lamps, 01 No Digital Amperemeter , 01 No Digital Voltmeter , 03 Nos 400/5A CI-1 15VA current transformer, 03 Nos MCB 6A 10KA SP , 06 Nos CT shorting Links & 01 No Netural Links. OUT GOING :-06 Nos MCCB 63A FP 10 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB)

Supply of Power make LT Switch Board with rupturing capacity of MVA at 415 Volts (type test done at CPRI BHOPAL) fully accessible form the front suitable for 3 phase “4 wire, 50 cycles A.C. supply weather proof, vermin proof, ventilated, front operated, floor mounting panel with compartments front cubical design, modular construction, fully compartmentalized, Indoor, Floor/Wall Mounted made out from 2/1.6 mm thick CRCA sheet A Panel duly painted with Powder Coated. General SpecificationsThe breaking capacity of ACB & MCCB as per electricity load . Electric Grade Aluminum bus bar with maximum current density of 1 amp. / Sq mm. suitable for 3 phase 4 wire 415 volt 50 Hz balanced/ unbalanced power system conforming to specifications.” The Bill of material/ component as per single line diagram. Metering set with all incoming Feeders on as per requirement. Panel are approved and successfully tested at 50 K.A. Breaking capacity of Bus bar 4000 A at C.P.R.I. Bhopal. Sheet steel Enclosure 2/1.6mm. C.R.C.A. sheet and Base frame of panel Board 75 x 40 x 3 mm. Nut, Bolt, washer shall be cadmium plated. Fully Compartmentalized. Gasket in all doors. Earthing with continousaluminum flat. Minimum clearance shall be maintained. Height of the panel as per site. Bill of material as per engineer-in charge drawing and specification. Makes of equipments& colour shade of panel board as per engineer-in-charge .asas per engineer-in-charge. PANEL :-Panel will be fabricated with 03 mm CRCA sheet steel for load bearing surfaces and 02 mm CRCA sheet steel for non load bearing surfaces with 3 mm gland plates. Paint shade is RAL 7032 , Cable entry in botttem , outdoor panel type ,floor mounted with MS angle 50x50xx6mm.BUS BAR :-600A Aluminium main bus bar , load wise sub feeder bus bar colour coated heat shrink bus bar sleeve nut -bolt, washer , hardware etc. INCOMER:- 01 No MCCB 200A FP 36 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB), 03 Nos R Y & B Phase indicating Lamps, 01 No Digital Amperemeter , 01 No Digital Voltmeter , 03 Nos 400/5A CI-1 15VA current transformer, 03 Nos MCB 6A 10KA SP , 06 Nos CT shorting Links & 01 No Netural Links. OUT GOING :- 02 No MCCB 100A FP 10 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB) , 02 Nos MCCB 63A FP 10 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB)

Supply of Power make LT Switch Board with rupturing capacity of MVA at 415 Volts (type test done at CPRI BHOPAL) fully accessible form the front suitable for 3 phase “4 wire, 50 cycles A.C. supply weather proof, vermin proof, ventilated, front operated, floor mounting panel with compartments front cubical design, modular construction, fully compartmentalized, Indoor, Floor/Wall Mounted made out from 2/1.6 mm thick CRCA sheet A Panel duly painted with Powder Coated. General SpecificationsThe breaking capacity of ACB & MCCB as per electricity load . Electric Grade Aluminum bus bar with maximum current density of 1 amp. / Sq mm. suitable for 3 phase 4 wire 415 volt 50 Hz balanced/ unbalanced power system conforming to specifications.” The Bill of material/ component as per single line diagram. Metering set with all incoming Feeders on as per requirement. Panel are approved and successfully tested at 50 K.A. Breaking capacity of Bus bar 4000 A at C.P.R.I. Bhopal. Sheet steel Enclosure 2/1.6mm. C.R.C.A. sheet and Base frame of panel Board 75 x 40 x 3 mm. Nut, Bolt, washer shall be cadmium plated. Fully Compartmentalized. Gasket in all doors. Earthing with continousaluminum flat. Minimum clearance shall be maintained. Height of the panel as per site. Bill of material as per engineer-in charge drawing and specification. Makes of equipments& colour shade of panel board as per engineer-in-charge .asas per engineer-in-charge. PANEL :-Panel will be fabricated with 03 mm CRCA sheet steel for load bearing surfaces and 02 mm CRCA sheet steel for non load bearing surfaces with 3 mm gland plates. Paint shade is RAL 7032 , Cable entry in botttem , outdoor panel type ,floor mounted with MS angle 50x50xx6mm.BUS BAR :-600A Aluminium main bus bar , load wise sub feeder bus bar colour coated heat shrink bus bar sleeve nut -bolt, washer , hardware etc. INCOMER:- 01 No MCCB 400A FP 36 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB), 03 Nos R Y & B Phase indicating Lamps, 01 No Digital Amperemeter , 01 No Digital Voltmeter , 03 Nos 400/5A CI-1 15VA current transformer, 03 Nos MCB 6A 10KA SP , 06 Nos CT shorting Links & 01 No Netural Links. OUT GOING :- 04 No MCCB 250A FP 36 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB) , 02 Nos MCCB 160A FP 36 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB) , 02 Nos MCCB 100A FP 36 KA TM based with (08 Nos of Spreader Links & 01 No ROM (remote operating machanizim ) per MCCB)

Supply of 3.5 Core 150 Sqmm Aluminium armoured Cable

Supply of 3.5 Core 95 Sqmm Aluminium armoured Cable

Supply of 3.5 Core 70 Sqmm Aluminium armoured Cable

Supply of 3.5 Core 35 Sqmm Aluminium armoured Cable

Supply of 3 Core 35 Sqmm Aluminium armoured Cable

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Above 35 sq. mm and upto 95 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Above 95 sq. mm and upto 185 sq. mm