Indian Army Tender

CATEGORY: Weld Mesh Panels should produced by electrical resistance welded galvanized wires and subsequently powder coated as per specification. , Omega clamps with profile cover plate to tighten the mesh panel along the post with 76mm dia 35mm width and 3 mm thickness as per specification. , Mushroom Head Bolt Nut with Washer Each clamps will be supplied with a pair of SS 304 mushroom headed square necked bolts and security nuts M8 X 50 as per specification. , Fence Post. Type Circular Hollow Material MS Steel Tube IS 1161. Dimentions 76 mm Dia and 3.2 mm plus or minus 10 percentage Thickness as per specification. , Straining Y Arm for supporting top PTCC Material. MS Angle Size 50x50x5mm as per IS 1852 as per specification. , Accessories for fitting Y Arm. Mushroom Head Bolt with breakable head safety nuts. Each Y Arm shall be supplied with two sets mush room headed bolts with security nuts and washers as per specification , Intermediate Y Arm for supporting top PTCC Material MS Angle Size 50x50x3mm as per IS 1852 Coating as per specification.. , Accessories for fitting Y Arm. Mushroom Head Bolt with breakable head safety nuts. , Anchor Rod. 10 mm dia 300mm long GI Rod tie with fence post at bottom using tie wire. 02 Nos for each post , Punched Tape Concertina Coil including spike and handle with 56 turns and dia 610 mm having a core wire of high carbon spring steel of high tensile strength as per specification. , Galvanised Steel Barbed Wire ISI marked A5 designation for Galvanised steel barbed wire for fencing shall conform to IS 278 1978 as per specification. , Quick setting compound , Aggregate 20mm Stone Aggregate to be crushed rock or gravel 20mm graded conforming to IS 383 of 1970 , Aggregate 40mm Stone Aggregate to be crushed rock or gravel 40mm graded conforming to IS 383 of 1970 , Ms Binding wire not less than 0.9mm dia confirming to relevant IS , Natural sand confirming to IS 383 of 1970 , Wire Cutter 18 inch , Aluminium Ladder 12 Feet length 12 to 13 inch width and 9 steps load capacity 150 Kgs and weight of ladder 12 Kgs , Hand Gloves Leather 500G , Hand Gloves Canvas , Hand Gloves Rubber , Bold Cutter 12 inch , Y Joint 10 Feet long , Y Joint 12 Feet long , Hammer with handle weight 5 Kg. , Steel Gurmala , Plumbob and Mason Thread , Cutting pliers size 8 inch for steel , Showel Square Nose 14 Gauge TATA High Carbon Steel , Hacksaw frame , Wooden Gurmala , Ratchet Spanner Single Socket 14 sproket , Trowel Masson Brick , Water Level Pipe 100 mtr , Hack Saw Blade Double Ended , Measuring Tape 5 mtr , Measuring Tape 30 mtr , Picks Axes with Chiesel and Point ends. Nominal weight 3.0 Kg overall length 595 mm with hard wooden handle. , Bosch GCO 220 corded electric metal cut off chop saw 2200W 3800 rpm Robust Base 355 mm cutting disc dia. , Iron cutting machine blade 355mm , Professional Impact Drill Machine 13 mm 600W GSB 13 RE , All type of Drill Bits for Drill Machine 13 mm 600W GSB 13 RE , Ratchet Spanner with deep Socket 12 to 13 mm , Welding Rods , Rivet Gun Machine alongwith 100 Nos of Rivet bit , Binding stick , Tasla Iron 18 inch , Fawada with wooden handle weight 2 Kg , Crow bar 5 feet long and 30mm thickness , Bolt cutter 32 inch , Wire cutter 150 mm , Alluminium straight edge 50mm sq 2 mm thick 1800mm long