Housing And Urban Development Department Tender

Finishing walls with Acrylic smooth exterior paint of required shade: Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface)

Finishing walls with textured exterior paint of required shade on New work (two or more coats applied @ 3.28 liter/10sqm) over and including base coat of exterior primer applied @ 2.20kg/10sqm

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters leadWith cement mortar 1:4 (1 cement : 4 fine sand)

Providing and applying Plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm widex1.6mm thick with flanges of 27mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x40mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.5mm of required length with nuts & bolts of requiredsize and other end of angle hanger fixed with G.I. channels 45x15x0.9 mm running at the spacing of 1200 centre to centre, to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5 mmat450mm centre to centre, shall befixed in a direction perpendicular to G.I. intermediate channel withconnecting clips made out of 2.64mm diaX230 mm long G.I. wire at everyjunction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre to centre, with 25mm long drive-all screws @ 230 mm interval ,including fixing of gypsum board/calcium silicate board to ceiling section and perimeterchannel with the help of dry wall screws of size 3.5x25mm at 230mm c/c, including jointing and finishing to a flush finish of tapered and squareedges of the gypsum board with recommended jointing compound, jointing taps, finishing with jointing compound in three layers covering upto 150mm on both sides of joint and two coats of primer suitable for both, all as per manufacturer specification and also including the cost of making openings for light fittings, grills defusers, cuttout made with frame of parameter chanels suitably fixed all complete as per drawing and specification under action of the Engineer incharge but excluding the cost of painting with 12.5mm thick tapered edge gypsum plain board conforming to IS: 2095-Part-1: 2011 (Board with BIS certification marks) including scafolding upto required height.

Painting with aluminum paint of approved brand and manufacture to give an even shade, one or more coats on old work

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows,Railings, all complete with : 5.0mm thick glass panes

Providing and fixing of Toughned and itched glass 6mm thick in already fixed aluminium panels of required shape and size including all necessary fittings screws etc .Complete Job

Supply, Installation, testing and commissioning of 3 Phase, 5HP Induction Motor Pump Assembly, for lifting of water including all the necessary accessories required for installation of motors.With 50 x 40mm dia with head range of 42.0-51.0 Rating IP55.

Repair and Rewinding of 5HP induction motor Including dismounting, carriage and re-installation at sangarmall city Centre. (complete job to make motor functional)

Repairs to starter Panel by way of replacement of 2 No. starter relay and single phase preventers(complete job to make system functional)

Bullet Camera (Analog) CCTV Monitoring, Recording & Streaming System as per the following specifications. Minimum 2-megapixel resolution. The frame rate shall be 25 FPS or better for viewing. IR Range 20 MTRS or above. Day/night operation:- The Camera should provide day/night functionality automatically switchs to night mode in low-light scenes. Certification: It should be FCC, CE, UL certified.

Dome Camera (Analog) CCTV Monitoring, Recording & Streaming System as per the following specifications. Minimum 2-megapixel resolution. The frame rate shall be 25 FPS or better for viewing. IR Range 20 MTRS or above. Day/night operation:- The Camera should provide day/night functionality automatically switch to night mode in low-light scenes. Certification: It should be FCC, CE, UL certified.

Supplying of 16 Channel 8MP 4K Analog Digtal Vidio Recorder (DVR)

3+1 coaxial copper CCTV Camera Standard Cable for video, power and audio communication.

Install, testing and commissioning of the above system complete job.