Housing And Urban Development Department Tender

Supply and Installation of unsheilded/360 degree sheilded Information outlets made of high impact plastic body with ABS, FR Grade halogen free material with provision for protection against dust in jack, suitable for Cat 6/6A application complying to latest ammendments, According. to Cat. 6/6A channel, It should support channel as well as components requirements of Cat.6/6A standards at frequencies of up to 250 to 500 Mhz. Cat 6/6A unshielded/shielded Jack should be suitable to terminate 4 pair, 23/24 AWG solid/stranded wire diameters, using 100 Ohm unshielded/shielded balance twisted pair cable, the jack should have tooless/impact termination on reliable copper tin plated Insulation displacement contact, with easy lock mechanism, It supports IEC 60603-7-4 and complied with ANSI/TIA/EIA 568 C.2 standard. jack should be RJ11,RJ12 & RJ45 compatible. Should support Ethernet 1.2 Gb/s ATM,Digital video and broadband/baseband analog video, Voice over internet protocal (VOIP) Specifications including modular/MS Boxes along with necessory connections as required. All as pre approved by Executive Engineer in charge.

Supply Installation Testing & Commissioning of following sizes Equipment Rack with provision for housing all control equipment with front & rear door, Blower for cooling, power Distribution Panel and proper locking arrangements.

12 U Rack

42 U Rack

Supply, installation, testing and commissioning of Patch Panel Cat 6 UTP Keystone type- 24 port - fully loaded with all accessories as required in complete respect as technical specification mentioned in compliance. Approved Make:- Panduit, Systimax, Dlink, Huber Shuner, Commscope

Supplying and fixing of following sizes of PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. (ISI Make).

25 mm

Supply , Installation and Testing of 4 pair, 100 Ohm impedance, Cat 6/6A /Class E/Ea patch cords should be constructed of minimum 23/24 AWG, stranded bare Copper cable with FRPVC/LSZH Jacket, with an enhanced performance by factory moulded RJ45 connectors with strain relief boots as per ANSI/TIA/EIA 568-C.2 suitable for Cat 6/6A application complying to latest ammendments Category 6/6A Standards, According. to TIA568C.2, ISO/IEC 11801, EN 50173, IEC 60603-7-51, EN 60603-7, IEEE 802.3an minimum requirement for 1G BASE-T to 10G BASE-T performance. Patch cords shall be straight thru cable compatible with both T568-A and T568-B wiring schemes, should support IEEE 802.3af / IEEE 802.3at for POE applications, Minimum 750 to 1000 mating cycles in plug contacts for long durability, Should support Ethernet 10GBASE-T, 1.2 Gb/s ATM, Token ring 4/16, Digital video and broadband/baseband analog video, Voice over internet protocal (VOIP). All as per pre approved by Engineer in charge. Cat 6, U/UTP (Unscreened/Un-sheilded Twisted Pair) Patch Cord

1 Mtr

3 Mtr

6 Mtr

Supply Installation testing and commissioning of 5 KVA/ 4 KW True Online , DSP Controlled online UPS with 1 phase AC input 50Hz and 1 phase AC output with 60 minutes backup on 12V SMF batteries Bank with Rack along with inter connecting battery cables and cable from UPS to Battery bank. The UPS should be with IGBT Based Rectifier and Inverter and with LCD/LED display for monitoring of its status along with inbuilt Galvonic Isolation Transformer. UPS should have following Features: UPS power factor : Input PF should be 0.99 AND output PF not less than 0.9 , Efficiency: up to 97% without Isolation ,Communication interface :RS232/USB port and optional SNMP compatibility for remote Monitoring, Audible Alarm : Mains Failure/Low battery / UPS Warning / Overload / Fault & By-pass Mode, THDI: not more than 5%, Noise Level less than 70db, CERTIFICATIONS & Standard : ISO-9001-14001 Certified ,Compatibility with DG Genset , Built in Automatic & Maintenance Bypass Switch,Warranty : 2 Years on UPS as well as on Batteries, Battery Make : Exide /Amaron/Quanta Make Preferred/Approved Brand : APC-Schneider /Emerson –Vertiv /Legrand-Numeric. OEM should have own service center in the district (Need to furnish the service centre address & contact details of at least 2 engineers for better services.

Supply Installation Testing and Commisioning of 3 X 2.5 sq.mm FRLSType Power Cable along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying of extension Card

5 Amp.

Providing & FIXING WIFI Dual Band/AP

Supply, Installation, & Testing of Indoor duplex Singlemode patch cord (9/125 μm (OS1/OS2) made of glass fiber optic with LSZH jacket, F8 2.0x4.1 mm, yellow, singlemode G652.D (9/125 μm (OS1, OS2) Mounted on both sides with ST/E-2000/SC/LC/MT-RJ/PC type Duplex connectors in acc. with IEC 61754-20. Zirconia (ceramic) ferrule with a PC polished endface geometry, connectors should be tuned in accordance with IEC 61755-3-1 and qualified in acc. with IEC 61753-1 for category U (uncontrolled environment, duplex clip and white plastic dust cover, should comply to delta IL 0.2 dB after 500 mating cycles, there should be an optional Visual coding, mechanical coding and lock protection on the patch cords which can be added on later stage. patch cords's performance should be acc. to IEC 61753-1 (Table A.12) as per latest ammendments of TIA/EIA 569B.3, as per requirements. All as pre approved by Executive Engineer in charge.

Single Mode Patch Cord 1 Mtr.

Single Mode Patch Cord 3 Mtr.

Electrical Works / Point Installation with all accessories (as per requirement at site)

Connectivity type ILL 10Mbps1:1 with Media OFC /ARC & OTC complete Job.