Central University Of Jammu Tender

For Openable Portion

Providing and fixing 12 mm thick pre laminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fitting aluminium handles ISI Marked anoidic coating not less than grade AC 10 transparent or dyed to colour or shade with necessary screws nuts washers complete

Providing & Fixing for Aluminium doors, mortise lock chrome plated brass 100 mm latch and lock with 6 leversgood quality as per directions of Engineer-In-Charge

Providing and fitting aluminium tower bolts ISI Marked anoidic coating not less than grade AC 10 transparent or dyed to colour or shade with necessary screws nuts washers complete300X10 mm

Providing & Fixing Hydraulic door closer

Providing & Fixing Aluminium hanging floor door stopper with Twin rubber

Earth work in surface excavation exceeding 30 cm in depth but 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: All kinds of Soils

Filling Available excavated earth (excluding rock in trenches), plinth sides of foundations etc, in layers not exceeding 20 cms in depth consolidating and depositing each layer by ramming, watering, lead upto 50 and for all lift.

Providing and Doing Brickwork with common burnt clay non Modular Bricks of class designation 7.5 in foundation and Plinth in CM(1cement:4coarse sand)

Providing and Doing Brickwork with common burnt clay non Modular Bricks of class designation 7.5 from Plinth Level to Floor V in CM(1cement:6coarse sand)

Providing and Doing Half brick masonary with common burnt clay non Modular Bricks of class designation 7.5 from Plinth Level to Floor V in CM(1cement:4coarse sand)

Providing and Doing 12 mm cement plaster in Mix 1:4( 1 cement:4 coarse sand)

Dry stone pitching 22.5 mm thick including supply of stones and preparing surface complete

Providing & Laying cement concrete 1:4:8(1 cement:4 coarse sand(Zone-III):8 Graded Aggregates)

Providing & Laying Rectified Ceramic Glazed Tiles of size 300mmX300mm in floor of Ist quality confirming to IS 15622 of approved make and shade laid on 20 mm thick cement mortar jointing with grey cement slurry @3.3 Kg per sqm including grouting the joints with white cement and matching pigments

Providing & Laying Rectified Ceramic Glazed Tiles of size 300mmX300mm of Ist quality confirming to IS 15622 of approved make and shade laid in skirting, risers of steps and Dado on 12 mm thick cement mortar jointing with grey cement slurry @3.3 Kg per sqm including grouting the joints with white cement and matching pigments of matching shades all complete.

Providing & Fixing White Vitreous China Pedestal Type Water Closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

Providing and fixing white vitreous china flat back half stall urinal of size580x380x350 mm with standard size C.P. brass flush pipe, spreaders with unions and clamps (allin C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, Autoclosing(Pressmatic) valve including painting of fittings and cutting and making good the walls and floors wherever required.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and Fixing of Health Faucet(CP Brass/SS) with 1 m long flexible tube as approved by Engineer-In-Charge

Providing and Fixing mirror of superior class 600X450mm beveled edge mirror of approved quality complete with 6 mm thick hard board ground fxed to wooden cleats with brass screw and washers complete.

Providing & Fixing 600X120X5mm glass shelf with edges round off supported on anodised aluminium angle frame with CP brass brackets and guard rail complete fixed with 40 mm long screw rawl plug etc complete.

600 mm long towelSS rail with total length of 645 mm, width 78mm and effective height of 88 mm, weighing not less than 190gms.

Providing and Fixing Drain Pipe PVC for Urinals Heavy Duty

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing.his includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints , cutting, chases making good the wall complete as per direction of Engineer in Charge. Internal work concealed work cutting chasing and making good the wall.20 mm nominal dia pipes

Providing and fixing C.P. brass bib cock of approved quality conforming IS 8931 15mm nominal bore

Providing and fixing C.P. brass bib cock long body of approved quality conforming IS 8931 15mm nominal bore weight not less than 810 gms

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Supply and Installing at site uPVC piping system using Solvent Cement ISI Marked [As perIS4985]with Heavy duty ISI Marked special fittings, Plain Bends ,Door bends, Coupler ,Reducers, Single Tees ,Door Tees, Double Tees, Reducing Tees, Plain, Ys, ,Door Ys, Double Ys, Elbows , Door Elbows,Floor traps(P,S type) etc. Adapters, Air vents, Clamping with GI UClamps as required for firmly installing the pipes. Testing of the system for leakage and Air tightness Complete 33.1 75 mm dia pipe(type B soil and Vent pipes)

100 mm dia pipe(type B soil and vent Pipes)

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement: 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal Dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

Extra depth for Manholes size 90X80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Laying Non Pressure NP2 Class ( Light Duty ) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1: 2 ( 1 Cement: 2 fine sand) incuding testing of joints and inlcuding trenching ( 750 mm deep) and refiling etc as required etc and connecting it with sewer/manhole : 150mm dia pipe

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than4.50 kg and frame to be not less than 2.70 kg as per standard design: 150X100mm size P type

Providing and fixing Sand Cast Iron grating for Gully trap 100 mm

Providing and Fixing SS grating 100 mm (lockable)(100 mm/75mm) dia for floor trap

Providing and laying damp proof course 40mm thick with cement concrete 1:2:4 (1cement:2 coarse sand:4 graded aggregate 12.5 mm and below derived from natural resources)

Providing and applying cement putty average thickness 1 mm of approved brand and manufacture over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with waterproofing cement paint of required shade new work New work (Two or more coats applied @ 3.84 kg/10 sqm)

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerincharge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including, cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete Hot finished welded type tubes.

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing false ceiling at all heights with integral densifiedcalcium silicate reinforced with fibre and natural filler false ceiling tiles ofSize 595x595 mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on interlockingmetal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm,cross - T of size24x32 mm of length 1200 mm and secondaryintermediate cross-T of size24x32 mm of length 600 mm to formgrid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fullythreaded hanger rod upto 1000 mm length and L-shape level adjuster ofsize 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25 mm flange to pierce into 12x50 mmor even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to befixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directionsof theEngineer-in-Charge. 15mm thick tegular edge light weight calcium silicate false ceiling tiles

Centring and Shuttering and removal of formwork for foundations footings bases of columns all works upto plinth level