Border Security Force Tender

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 75 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 75 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm diameter

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /seIf tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm)

Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink without drain board 610x460 mm bowl depth 200 mm.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge 25 mm nominal outer dia Pipes

Providing and fixing uplasticised PVC connection pipe with brass unions : 30 cm length 15 mm nominal bore.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: 15 mm nominal size

Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includesmaking necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing PTMT grating of approved quality and colour. Circular Type 100 mm nominal dia.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. 25 mm nominal bore, 152 mm long. Weighing not less than 440 gms

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements. Weighing not less than 106 gms.

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing PUF panels for wall & false ceiling as per direction of Engineer-in-charge with following specification & directions:- The PUF panels shall be 60 mm thick made using 0.60 mm PPGI skins on both sides and CFC Free 44 kgs bulk density (+/-2 Kgs) PUF insulation in between. The PUF Panels will be joined together using tongue & groove and cam lock arrangement as per Manufacturer standard. The PUF insulation materials in the panel shall have fire retarding and self-extinguishing properties as per international standard. The wall/False ceiling panels shall be manufactured on dis continuous production line having integrated decoiler, forming machine capable on line ribbing and folding PPGI sheet and shall use PLC controlling high pressure dispending machine of required capacity to inject specified amount of PUF Chemical for consistence quality on line. The PUF panel manufacturing machine shall be capable of monitoring and controlling the injection rate to assure specified uniform density dimensional stability and compressive strength. The manufacture/manufacturing facility must full fill following criteria on quality and production capacity. The Wall Panel outside PPGI colour will be RAL 1001 and inside colour will be RAL 9002 / 9003. The False Ceiling Panel outside & Inside PPGI colour will be RAL 9002 / 9003. Other details of panels are as follows:- All material required for the manufacture of shelter shall be new and shall comply with relevant Bureau of Indian Standard Specification. (a) The bulk density of PUF insulation should be 44 Kg/Cum +/- 2 Kg/ Cum made from CFC free close cell polyurethane foam and the dispensing machinery should be kept with a PLC controlled panel for monitoring and controlling the injection rate to assure specified uniform density requirements. The total thickness of the finished composite wall panel should be 60 mm. The tolerance in the panel can only be on the plus side. (b) 0.6 mm thick PPGI sheet 'U' channel of size 65mm x 40mm at the bottom (Floor level) and top shall be provided to slide and fit the wall panels. Suitable arrangements will be made to fix the U channel to floor at bottom and on top to structural members. PUF Panel Joining arrangement. The PUF panels shall have Tongue and groove type of joint formed on line on the forming machine integrated with PUF panel manufacture machine. (c) The manufacture shall have facilities for conducting bend test, impact resistance test, pencil hardness test, cross hatch adhesion test, paint coat thickness test to IS-14246 and for galvanizing test to lS-277. The manufacture of PUF panel shall have test certificate/report for fire BS 476 chapter V,VI,VII from CBRI Roorkee for any sample of PUFpanels. (d) The outer and inner colour coated sand yellow colour (RAL-1001) GI skin made from hot dipped galvanized steel of the panels should be 0.6 mm thick TCT (Total coated thickness). Each panel should be supplied pre-painted with a colour coating of 50 microns of architectural polyester on a minimum 175 gms/m² base of Zinc coating on the finished surface only for protection against scratches during handling and transportation. Base metal of Gl skin CRCA should be as per IS-513 and grade of zinc coating will be 175 as per lS-277. The pre coated Gl sheet skin should have min coating of 4.5 micron epoxy primer and 25 micron polyester top coat on the finished surface and 7-8 micron primer Alkyd Backer on backside which is bounded to the polyurethane foam. The pre coated Gl sheet should conform to IS 14246-1995 with manufacturer test certificates conforming to specification.

Providing and fixing Floor panels as per direction of Engineer-in-charge with following specification & directions:- The floor panels of the shelter & wind breaker room shall be of 60 mm thick. The panels will be made using 0.60 PPGI skin (RAL- 9002/9003) at the bottom and 40 mm CFC Free 44 kgs bulk density (+/-2 kgs) PUF Insulation in between along with 18 mm thick BWR grade plywood on top. The Floor panels will be joined using cam locks & tongue and groove arrangement produced on discontinuous panel production line. The floor top will be be provided with 2 mm thick aluminium chequered sheet fixed with suitable counter sunk screws. The floor top finishing will be provided with 2mm thick vinyl sheet will be over the top surface of floor.

Providing and fixing of Windows with frame & canopy in PUF wall panel to be fixed with 1.5mm thick UPVC Section 2 track sliding window of size 900mm x 1100 mm. UPVC sliding shutters with double insulated toughened glass (5mm toughened glass +10mm air gap using strip +5 mm toughened glass = double glass Insulated window) along with aluminium 3mm thick grill of standard pattern. Window will have proper locking arrangement and will be fixed to the wall panels using suitable screws. Window Canopy Rain/sun shed of 0.60 mm thick PPGI sheet of size 1200 mm x 450 mm using angle iron frame of size 35 x 35 x 3 mm duly painted over with red oxide primer. All UPVC framework material should conform to IS 513, 1996. All sections of UPVC frame/track shall be 2 mm thick and shall be of ISI mark.

Providing and fixing of Door with frame & canopy in PUF wall panel as per direction of Engineer-in-charge with following specifications:- Doors-Size 995x2135 mm- Door outer frame shutter will be made up of suitable 2 mm thick MS section. The door internal shutter shall be of 40 mm thick puf panel made from 0.60 mm PPGI sheet on both sides and 44 Kgs PUF density. The internal shutter will be hanged with 3 Pcs heavy duty hinges. 2 Nos aluminium aldrop of 250 mm and Aluminium tower bolts of 200 mm size from inside and 2 Nos D type handles will be provided in each shutter. Canopy- Rain/sun shed of 0.60 mm thick PPGI sheet of size 1000 mm x 450 mm using angle iron frame of size 35 x 35 x 3 mm duly painted over with red oxide primer.

Providing and fixing of Bunk Bed (as per drawing) with PUF Mattress. Two tiers x two set of Bunk bed of size 915mm x 1830mm to be supplied/fixed as per drawing. Bed should be made of MS Section- RHS 50x25x2mm special hollow section and 25mm x 5mm Tai Flat Mild steel strip. 12mm BWR/BWP Ply covered with 42Kg per Cum Density Foam and Leatherite / rexine cloth, the bed should be of suitable size to take 200 Kg load & 1050mm down from the roof. The lower bed will be at 450mm height from the Floor with Six legs of 50x50x2mm SHS hollow section. A Provision of stair case to be given to access the top bed and also arrangement of two storage system below the lower bed etc. complete as per direction of Engineer-in-Charge. PUF Mattress- Size of cushioned platform with plywood of thickness 12 mm and size 1830 x 910 mm. Cushion provided to be thickness 100 mm with density of 40 kg per Cum. Total 112 mm thick. Note- The each member of sleeping of sleeping bunk shall be detachable and shall be assemble with help of suitable nut/bolt and washers.

Providing and fixing 1500 ltr capacity aerobic Bio digester FRP tank of approved make with following specification & directions:- Bio-digester:- Aerobic bio digester of approved make with 1500 ltr capacity for toilet block will be provided below the toilet chamber and suitability connected with the commodes. Instant heating rated 1 KW in out let chamber to be provided for emergency heating (to save bacteria). The culture (bacteria septic clean liquid) to be provided with each toilet for one year duration. All three chambers FRP digester with heat tracer shall be provided. The three chambers A, B, C shall be such that chamber A shall be the inlet and chamber C shall be the discharge end. There shall a vent system connection A & B chamber to convey the gases generated to the height of about 4 mtrs. All the three chambers A, B & C shall be connected at the bottom most level with 3 inch dia polypropylene full way valve so that in close condition of valves and when the system is not use, the contents in the three chambers are independently held without any chance for a mix up. In the open condition of the valve all the three chambers gets connected, the vertical pipe near the chamber C can tale in a two inch suction pump which can empty the system. The Content from chamber C should be discharge into a trailer mounted holding tank which can be discharge to a remote location of biogas generation system wherever possible.

Providing and installing kerosene heater (Size 446 X 446 X 585 (mm)) Model No. PS-22G, heating out put max. 23,000 Btu/Hrs, process continuous combustion max. 8-12 hrs air density having thermal efficiency 90% (Plus-minus 2%) maximum hot air temperature from 25 to 75 degree centigrade, Continuous consumption duration (kero) 0.66 ltr/hrs on full load, Ignition method-Battery-C, Cellx2, Ignition Type-B, Tank capacity 7.2 ltrs, weight -10.50 Kg & stainless steel Burner, Detailed specifications attached with user manual and as per directions of engineer-in-charge.

Providing and fixing PVC floor trap including the cost of cutting and making good the walls and floor 100 mm inlet and 75 mm outlet all complete as per direction of Engineer-in-charge.

Fixing of available structural steel elements i.e. bottom frame, roof frame, struss, runners etc. with riveted, bolted or welded including cutting, hoisting, fixing in position as per requirement and as per direction of the Engineer-in-charge.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. Group -B

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (i) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (ii) 2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. As required. (i) 5/6 A switch

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. As required. (ii) 3 pin 5/6 A socket outlet

Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 A socket outlet and 15/16 A piano type switch, connections, painting etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. As required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

Supplying and fixing following way SP&N sheet steel, MCB distribution board , 240 volts on surface/ recess complete with tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)- (i) 16 way, Double door

Supplying and fixing following way SP&N sheet steel, MCB distribution board , 240 volts on surface/ recess complete with tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)- (ii) 08way, Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. A) single pole

Supplying and fixing following rating, double pole, 240 V,isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. A) 40 Amp

Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure wit cover plate having locking arrangment and watering pipe etc. with charcoa/coke and salt as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe FRLSom earth electrode including connection with G.I. thimble excavation and re-filling as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc with charcoal/coke and salt as required.

Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, tube, having single prong at top, with 85 mm dia 6 mm thick G I base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required. (For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Supplying installation testing & commissioning of 20 watt 4Ft LED Tube light battan fitting complete with tube light , directly on ceiling / wall incluiding making connections with 1.5 SQ mm , FRLS PVC insulated copper condutor single core cable and earthing etc as required of Havells make (Model No.LHEXAWP6IN1W020) or equivalant make of Philips/Bajaj

Supplying & fixing of 400 mm swing wall fan (PVC Blade)- , suitable for operation single phase, 230 volts, 50 Hz, AC supply including wallmounting clip, with rope mounting regulator etc. as required of make (Crompton /havells/ bajaj,usha.)

Supplying,installation, testing and commissioning of 250 mm exaust fan PVC Body suitable for operation on 230 volt, single phase, 50 hz, ac supply i/c lauvers and shutters make Crompton model BRISK AIR NEO light duty or equivalent make of Havells/CG/Usha including connections with1.5 SQ mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying and fixing of LED 10 watt of Philips/Havells on the exsting holder etc as required.

Supplying & Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size 2 x 25 sqmm, direct in ground including excavation and refilling the trench etc. as required, but excluding sand cushioning and protective covering.

Supplying & laying of one number PVC insulated and PVC sheathed / XPLE power cable of 1.1 KV grade of size 2 x 25 sqmm. in the existng RCC / HUME / METAL pipe as required.

Supplying & Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of size 2x25 sqmm, In the existing masonary open duct as required, .