Urban Development Department Tender

Providing and laying in position machine batched and machine mixed design mix M-20 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge All work above Plinth Level upto V Level

Steel reinforcement for reinforced cement concrete work including strengthening, cutting, bending, binding and placing in position complete and binding all complete avobe plinth level TMT bar grade Fe-500

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :CM 1:6

Providing and fixing Powder coated Coloured anodised aluminium extrusion section of Jindal/ Hindalcao aluminum or its equavqlent work for door, window ,ventilator and partition with extruted built up standard tubular and other sections of approved make confirming to IS:733 and IS:1285 anodised transparent or dyed to require shade accordingly to IS:1868 (minimum anodic coating of grade AC15) fixed with raw plugs and screws or with fixing clips , necessary filling up of gaps and junctions at top , bottom and sides with required with PVC / neoprene filles etc. aluminium section shall be smooth rust free, straight, mitred and jointed mechanically wherever required including clests angle, aluminium, snap beeding for glazing/ panelling C.P. brass / stainless steel screws all complete as per Architectural Drawings and the direction of the Engineer -in Charge.for doors, windows and ventilators and glazed partitions frames

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in-charge . (Cost of aluminium snap beading shall be paid in basic item

Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS: 733 andIS: 1285, fixing with dash fasteners of required dia and size, includingnecessary filling up the gaps at junctions, i.e. at top, bottom and sides withrequired EPDM rubber/ neoprene gasket etc. Aluminium sections shall besmooth, rust free, straight, mitred and jointed mechanically whereverrequired including cleat angle, Aluminium snap beading for glazing /paneling, C.P. brass / stainless steel screws, all complete as perarchitectural drawings and the directions of Engineer-in-charge. (Glazing,paneling and dash fasteners to be paid for separately) :

Providing and fixing stainless steel wire mesh in aluminum doors , windows, ventilator shutter for partion etc. Complete as per architectrual drawing and the direction of Engineer -in charge ( Wire mesh shutter)

Providing and fixing aluminium anodised powder coated pattern to existing window/ventilatior with 80mmx80mm panels holes with 25x8mm thick aluminium flat in windows and ventilators including fixing with aluminium screws or bolts and nuts complete in alluminium channels base frames (Aluminium channels base frames to be measured and paid for separately

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

250x10 mm

100x10 mm

Providing and fixing aluminium handles, ISI marked,anodised (anodic coating not less than grade AC 10 asper IS : 1868) transparent or dyed to required colour orshade, with necessary screws etc. Complete

125mm

100 mm

Providing and fixing oxidised M.S. casement stays(straight peg type) with necessary screws etc. complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge. 60 mm

Providing and fixing pre-painted sheet roofing of kotar metal single skin trapezoidal 10 (ten) refitted sheeting 0.60mm thickness having 1060mm (one thousand sixty millimetre) cover width cover all width 1126mm, 28mm crest depth at 353mm (three hundred fifty three millimetre) 2.50mm (two decimal fifty millimetre) the main crest with at top 25mm and at lower 81mm base metal of coil rolled steel coil with zinc waiting top coat with regular modified polysters coating of approved shade and balancing reverse coat 5.5mm (five decimal five millimetre) dia and 55mm (fifty five millimetre) length with EPDM seal complete in all respect

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat ofapproved steel primer all complete.

Providing and fixing plaing B.P. sheet 1.60 mm (one decimal sixty millimetre) thick 16 SWG fixed in soffits ceiling including jointing with gas/electric welding in position complete (frame work is to be measured paid for separately)

15 mm cement plaster in single coat on rough side of brick/ stone masonry for interior plaserting upto floor two level with Cm 1:6

Dismeteling of Steel work in single section including dismembering and staking with in 50 meter lead in channel angle Tees and flats

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :Water thinnable cement primer

Wall painting with exterior emulsion paint of approved brand and manufacture to give an even shade exterior