The Himachal Pradesh State Industrial Development Corporation Limited Tender

Providing and laying Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, fecia ,mouldings, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size).and curing complete, mixing the material in mechanical mixture and compacting the concrete with viberator complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. including carriage of materials upto all leads and lifts.

Providing and laying tor steel(Tata/Sail/RINL/Shyam steel make) reinforcement for reinforced cement concrete work including ,bending binding,straightening and placing in position complete in all floor level/ heights including cost of binding wire complete including entire carriage of material within all leads and lifts and other incidentials as per the direction by the Engineer-in-charge .

Providing Brick work using common burnt clay building bricks in superstructure 1:6 (1cement:6sand) up to all height including carriage of material within all leads, lifts and heights. 1st class bricks.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) : including carriage of materials upto all leads and lifts. (A) For fixed portion Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) including carriage of materials upto all leads and lifts.

(B) For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) including carriage of materials upto all leads and lifts.

Providing and fixing glass glazing in aluminium door, window, ventilator shutters and partition etc with PVC/neoprens gasket and including aluminium beading complete as per the architectural drawings and the directions of Engineer-In_charge including cost of aluminium snap beading . glazing with glass panes of 4 mm thickness (weight not less than 10 kg/sqm. including carriage of materials upto all leads and lifts.

Providing and fixing 12mm thick prelaminated Particle board board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge. Pre-laminated particle board with decorative lamination on both sides including carriage of materials upto all leads and lifts.

Providing and fixing dyed Stainless steel sliding door bolt anodized colour and shade with bolts and nuts screws etc., complete: including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (A) 300X16 mm

Providing and fixing dyed aluminium hooks and eyes dyed to required shade and colour with screws etc., complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. 150mm

Providing and fixing dyed aluminium tower bolt (barrel type) anodized transparent or dyed to required shade and colour with screws etc., complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (A) 200x10mm

(B). 150x10mm

Providing and fixing Stainless steel handles dyed to required colour of shade with necessary screws etc., complete: including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (A) 200x10mm

(B). 150x10mm

6mm (Six milimetre) cement plaster to ceiling in cement mortar 1:3 (One Cement is to three Sand) in all floor level. The rate isincluding carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

15mm (fifteen milimetres) thick cement plasters in single coat on rough/fair side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Applying Birla white wall care putty two coats over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. including carriage of materials upto all leads and lifts.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of materials upto all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth and cement primer complete. including carriage of materials upto all leads and lifts.

Providing and fixing double charge 10mm thick anti skid water proof stain and impect resistent heavy duty and Mat Finish vetrified tiles Nitco or equivalant 800mmx800mmx10mm manufactured of required shade and colour in flooring, treads of steps and landings laid with spacers laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) and jointed with grouting of Epoxy material mixed with pigment to match the shade of tiles in all storeys, height, levels and location as required complete.including carriage of materials upto all leads and lifts.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.62 mm (+ 0.05 %)of TATA Steel durashine total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge. Tata make

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately):12mm thick

Providing and fixing of M.S. BP sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instructions of the Engineer-in-charge. (weight of sheet not less than 15kg/sqm).including carriage of materials upto all leads and lifts.

Structural steel work riveted, bolted or welded in built up sections, trusses, tabular sections of any size and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China including carriage of material within all leads and lifts.