The Himachal Pradesh State Industrial Development Corporation Limited Tender

Providing and laying Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, fecia ,mouldings, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size).and curing complete, mixing the material in mechanical mixture and compacting the concrete with viberator complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. including carriage of materials upto all leads and lifts.

Providing and laying tor steel(Tata/Sail/RINL/Shyam steel make) reinforcement for reinforced cement concrete work including ,bending binding,straightening and placing in position complete in all floor level/ heights including cost of binding wire complete including entire carriage of material within all leads and lifts and other incidentials as per the direction by the Engineer-in-charge .

Providing Brick work using common burnt clay building bricks in superstructure 1:6 (1cement:6sand) up to all height including carriage of material within all leads, lifts and heights. 1st class bricks.

Providing and fixing NCL Soccular Frame Work (Japani Chaukhat) in door ,window and ventilator frame fabricated from section roll formed out of 1.3 mm thick galvanised steel ( Base steel as per IS 513 with Zinc of 120 Gram/Sqm. Powder Coated with pure polyster powder upto 50-60 micron thick. The over all size of the frame should be 150mmx60 mm with double rebate of 37 mm ,100mm hinges matching shade and holdfast . the frame section shall be cut to length and meter jointed with corner brackets made of electroplated including carriage of materials upto all leads and lifts.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) : including carriage of materials upto all leads and lifts.For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) including carriage of materials upto all leads and lifts.

Providing and fixing glass glazing in aluminium door, window, ventilator shutters and partition etc with PVC/neoprens gasket and including aluminium beading complete as per the architectural drawings and the directions of Engineer-In_charge including cost of aluminium snap beading . glazing with glass panes of 4 mm thickness (weight not less than 10 kg/sqm. including carriage of materials upto all leads and lifts.

Providing and fixing stainless steel wire gauge of IS gauge designation 140 g with wire of dia 0.71 mm to windows and clerestory windows including U shape beading and clip of aluminium including carriage of materials upto all leads and lifts.

Providing and fixing panelled shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, and including Butt hinges and necessary screws all complete as per direction of Engineer-incharge. sheesham wood 35 mm thick shutters including carriage of materials upto all leads and lifts.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete fixed to Aluminum window/ Steel window by secrews/welding including carriage of materials upto all leads and lifts.

Providing and fixing dyed Stainless steel sliding door bolt anodized colour and shade with bolts and nuts screws etc., complete: including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. a) 300X16 mm

Providing and fixing dyed aluminium hooks and eyes dyed to required shade and colour with screws etc., complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. 150mm

Providing and fixing dyed aluminium tower bolt (barrel type) anodized transparent or dyed to required shade and colour with screws etc., complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. ( a). 200x10mm

( b). 150x10mm

Providing and fixing Stainless steel handles dyed to required colour of shade with necessary screws etc., complete: including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. ( a). 200mm

( b). 150mm

15mm (fifteen milimetres) thick cement plasters in single coat on rough/fair side of brick/concrete/stone walls for interior/exterior plastering upto all floor level including arises, internal rounded angles, chamfers and or rounded angles not exceeding 80mm (Eighty milimetres) in girth and finished even and smooth with cement mortar 1:6 (one cement: six sand) including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge.

Applying Birla white wall care putty two coats over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete. including carriage of materials upto all leads and lifts.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of materials upto all leads and lifts.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth and cement primer complete. including carriage of materials upto all leads and lifts.

Painting two coats (excluding priming coat) on new steel and other metal surfaces with enamel paint brushing to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matters:- With white enamel paint.or other than white including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing double charge 10mm thick anti skid water proof stain and impect resistent heavy duty and Mat Finish vetrified tiles Nitco or equivalant 800mmx800mmx10mm manufactured of required shade and colour in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) and jointed with grouting of Epoxy material mixed with pigment to match the shade of tiles in all storeys, height, levels and location as required complete.including carriage of materials upto all leads and lifts.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.60 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.including carriage of materials within all leads and lifts and as per the direction of Engineer-in-Charge. Tata make

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked, to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately):12mm thick including carriage of materials upto all leads and lifts.

Providing and fixing of M.S. BP sheet 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instructions of the Engineer-in-charge..including carriage of materials upto all leads and lifts.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paintIn gratings framed guard bars,ladders,railling,brackets , roof and similar works of using channels ,Tee,angles,circular, square,Tubular pipesof any size and rectangular hollow sections and including carriage of materials upto all leads and lifts.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :Ridges plain (500 - 600mm)

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China including carriage of material within all leads and lifts.