The Himachal Pradesh State Industrial Development Corporation Limited Tender

Dismantling wooden ballies in posts and struts including stacking with all leads including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking with all leads : of area 3 sq. metres and below including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in- Charge.With cement mortar 1:4 (1 cement : 4 fine sand) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth Cement mortar 1:6 (1 cement : 6 coarse sand) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

15 mm cement plaster on the rough side of single or half brick wall of mix :1:4 (1 cement: 4 fine sand) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.20 mm M.S. laths with 1.20 mm thick top cover including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing ball bearing for rolling shutters including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Extra for providing mechanical device chain and crank operation for operating rolling shutters. Exceeding 10.00 sqm and upto 16.80 sqm in the area including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.60 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a) Ridges plain (500 - 600mm)

(b) Gutter (600 mm over all girth)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) sal wood including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete, 35 thick of Hollock wood including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete With 12 mm mild steel U beading including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth. Priming coat with distemper primer including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Finishing walls with Acrylic Smooth exterior paint apexultima of required shade Two or more coat applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm. including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Earth work in excavation by mechanical/(Hydraulic excavator) / manual means in foundation trenches or drains of any width and depth, including dressing of sides and ramming of bottoms, including getting out the excavated soil and disposal of surplus excavated soil within all leads and lifts as directed, in all kind of soils including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and Laying concrete for plain/reinforced concrete in open foundations complete as per drawing and technical specification clauses 802, 803, 1202 and 1203 cement concrete 1:4:8( 1 cement :4 Sand :8 graded stone aggregate 40 mm nominal size) including cost of formwork including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in- Charge.80 mm thick C.C. paver block of M-40 grade approved by HPPWD (NTC/Ashok Panjla Tiles/NTCCI/Pooja Concrete Fabricators, M/S Dalal Tiles Pvt. Ltd.) with approved color design and pattern including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) Medium shade pigment using 50% white cement 50% Grey cement including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 Nominal mix (1:2:4) ( 1 cement :2 Sand :4 graded crushed stone aggregate 20 mm nominal size) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. (a) 20 mm dia nominal bore

(b) 25 mm dia nominal bore

Providing and fixing brass bib cock of approved quality including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. : 20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) including carriage of materials upto all leads and lifts and as per the direction of Engineer-in-Charge. : (a) 20 mm dia nominal bore

(b) 25 mm dia nominal bore

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China including carriage of material within all leads and lifts.