Ropeway And Rapid Transport System Development Corporation HP Limited Tender

Centering and shuttering including strutting, propping etc. and removal of form work for:-Foundations, footings, bases for columns as directed by engineer in charge.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. (Excess/less cement over the specified cement content used is payable /recoverable separately) Providing M-30 grade concrete instead of M- 25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Hard drawn steel wire as directed by engineer-in-charge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes s directed by engineer in charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, chaquired sheet base plate, anchor bolt, nut and bolt, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete s directed by engineer in charge.

Providing and fixing Polycarbonate sheet multiwall UV protected having thickness of 10 mm in roof along with ridge and all complete as per direction of Engineer in-charge.

Providing and Installation of Rubber Tile made from recycled rubber uniform color, strong and durable quality, light weighr and tear resistance having 15mm thick with tensile strength 1.5 MPA to 2.0 MPA, % elongation break at 100 to 130, and density of 980 kg/m3, hardness Shoe A 62 and no deformation in temperature variation -20 degree celsius to 100 degree celsius and fire resistant. Material must be anti-skid, foot grip, scratch resistance and highly impact resistance. Rubber tile must be fixed with floor proper adhesive chemical glue as per direction of Engineer-in-Charge.

Designing fabricating testing installing and fixing in work gang saw cut (polished and machine cut) of position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium Marble work gang saw cut (polished and machine cut) of aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coats on new work as directed by engineer in charge.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : Toughened glass panes 12 mm thickness

Supplying Installation Testing commissioning of 24 passenger (884 kg lift having contract speed of 1.7MP Sserving G+4 Floors in the lift shaft and having barrier free requirements as per Appendix-VIIof CPPWD General Specifications for Electrical Works (Part-III-Lifts &Escalators) ,2003 and as per detailed specifications enclosed as per detailed specifications enclosed as per speed -1.7MPS Floor to be served equal to ground + 2 Travel-36 Mteres(approx) Stops & opening -One or two opposite side Machine :Fearless Machine with permanenbt magnent motor controller- AC Variable Voltage Variable Frequency Control Operation -Automoatice ,microprocessor based with /without attendent power-415 V,3 Phase,50 Hz,AC,4 wire system Door Operation -Automatice door opration with adjestable door opension and closing timinings Type of doors Car Cabin doors-Centre opening power operatored horizontal sliding doors in stainless steel moon kfinish Clear opening of car entrance and hoist way enterance -800 mm(W)x 2000mm(H)Landing doors-Stainless steel scratch resistant finish, two hours fire rated,Centre opening powers doors and in other three sides and one side of cabin stainless steel finsih and other two side with toughend glass/ door finish as per design specification satiisfaction and direction of Engineer-in-Charge.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing & Laying of one number aluminium conductor, PVC insulated and PVC sheathed armoured/ XLPE power cable, 1.1 KV grade of following sizes on wall surface as required. 3.5 core cable (35 sqm cable)

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 Amp

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required. 250 A, 25 KA,TPMCCB

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 2.5.2 8 way (4 + 24), Double door

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group A as per direction of engineer in charge as direction of engineer in charge

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire as direction of engineer in charge

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. as direction of engineer in charge

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. 180 mm X 100 mm X 60 mm deep as direction of engineer in charge

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required.5/6 amps switch as direction of engineer in charge

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 15/16 A switch as direction of engineer in charge

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way , Double door as direction of engineer in charge

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. Single pole as direction of engineer in charge

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.