Public Works Department Tender

Providing and laying 60mm (Sixty milimetre) factory made chamfered edge Cement Concrete paver blocks of NTC or equivelant in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge and including curing and carriage of materials in all leads and lifts as per direction of The Engineer-In-Charge complete.

Providing and fixing 19 mm (nineteen millimetre) thick water proof termite resistant commercial board box including shelves and shutters, the back side cupboard / cabinet shall be 8 mm (eight millimetre) thick ply and all the cut portions of shelves shall be finished with 6 mm (six millimetre) thick hard wood edging. The cut portion of shutters from all sides shall also be finished with 12 mm (twelve millimetre) thick hard wood edging. The shutter from outside shall be finished with 4 mm (four millimetre) thick veneer Ply of approved shade to match with paneling including stainless steel hinges and magnetic catcher with in all accessories etc. complete as per detailed drawing as per direction of Engineer-in-charge including all leads, lifts and carriage of material and other incidental including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge Concealed work, including cutting chases and making good the walls etc 20 mm nominal outer dia Pipes including all leads, lifts and carriage of material and other incidental including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

P/F 12 mm THICK PRELAMINATED BOARD BOTH SIDE bwp PHENOL BONDED EXTERIOR/INTERIOR GRADEIN PARTITION/CABIN WITH FRAME OF FIRST CLASS DEODAR FOR DOORS I/C BRIGHT FINISHED/BLACK ENAMELLED IRON PIANO HINGES WITH NECESSARY SCREWS AND GLASS PANES OF 8 MM THICK IN PARTITION 40 mm THICK FRAME

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :150 mm including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing E-channels for cup boards slider transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc.Kiln seasoned and chemically treated hollock wood including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with ecessary accessories and screws etc. complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour 15 mm nominal bore with 45 cm length including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing soil, waste and vent pipes of 75 mm dia Sand cast iron S&S pipe as per IS: 1729 including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing plain bend of required degree of 75 mm dia Sand cast iron S&S as per IS -1729 including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete Flexible pipe 40 mm dia including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing 100 mm sand cast Iron grating for gully trap including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing PTMT towel rioal complete with bracket fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors 100 mm inlet and 75 mm outlet Sand Cast Iron S&S as per IS- 1729 including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms ncluding carriage of imaterials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing chromium plated brass curtain rod having wall thickness of 1.25mm with two chromium plated brass brackets fixed with C.P. brass screws and PVC sleeves etc., wherever necessary complete 25 mm dia including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 35 mm to 40 mm thick in hollock wood incuding all leads and lifts as per direction of The Engineer-In-Charge complete including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.

French spirit polishing Two or more coats on new works including a coat of wood filler including carriage of materials in all leads and lifts and as per directions of The Engineer – in – Charge complete.