Public Works Department Tender

Earth work in excavation for all type of road structure such as retaining walls, breast walls, culverts, drain and Parapets etcetra in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiseling /wedging out rocks (Where blasting is prohibited) as per drawings and M.O.R.D. technical specification section 300 and 1600 and as per direction of the Engineer- In – Charge including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto any lead and lift including dressing of sides, bottom and back filling in trenches with excavated suitable approved material to the original surface in layer not executing 150 mm (one hundred fifty millimetre) compacted thickness including shoring and strutting and pumping and bailing out water (surface and sub soil water ) upto any depth any quantam of water including cleaning of slush which may arise out during dewatering complete as per direction of Engineer-in-Charge. Including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST

Providing and laying mechanically mixed and vibrated plain cement concrete in all type of structure as per drawing and MORD technical specification section 800, 900 ,1200 and 1600 for nominal mix 1: 4: 8 (one cement isto four sand isto eight graded crushed/broken stone aggregate 40mm (forty millimetre) nominal size and curing complete including pumping or bailing out water, dewatering, removal of slush as required at site which may arise at the time of laying concrete complete for all heights/depths including the cost of form work in retaining walls, breast walls etcetera as per the direction of Engineer-in-Charge including carriage of materials, within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST

Providing and laying 110mm (one Hundred ten millimetre) dia with working pressure not less than 4.000 kg/ cm^2 (four point zero kilogram per square centimetre ) ISI marked PVC pipe weep holes in brick masonry/stone masonry, plain reinforced concrete, Abutments, Wing walls, Return walls and retaining/breast walls extended through the full width of the structure with slope I(V):20(H)(One vertical : Twenty Horizontal) towards draining face complete as per drawing and MORD technical specification section 700 and 1200 and as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST

Providing and laying of boulder apron laid in wire crates with 4 mm (four millimetre) dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm (one hundred millimetre into one hundred millimetre) mesh (woven diagonally) including 10 % (ten percent) extra for laps and joints laid with stone boulders weighing not less than 40 kg (forty kilogram) each as per drawing and MORD technical specifications section 1300 including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST

Construction of granular sub base by providing well graded materials as per table 400.1 and spreading in uniform layers with tractor mount grader on prepared surface, mixing by mix in place method with rotavator at OMC and compacting with three wheel 80-100 (eighty -one hundred) kN static roller to achieve the desired density, as per MORD Technical Specifications Section 400 for grading-I material and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental.The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100 ( eighty to one hundred) KN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and M.O.R.D.Technical Specification Section 400. and direction of Engineer-in-Charge including carriage of materials within all leads and lifts and other incidentals. The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and applying primer coat with Bitumen emulsion (SS-I) on the prepared surface of granular base including cleaning of road surface with Hydraulic brooms and spraying primer at the rate 1.00 Kg. ( One kilogram) per square metre by mechanical means as per M.O.R.D. technical specifications section 500 as per the entire satisfaction and directions of Engineer – in- Charge including carriage of materials within all leads,lifts and other incidentals . The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing, laying and rolling 50mm (fifty millimetre) compacted thickness cold mix bituminous macadam with 75 ( Seventy five) TPH drum mix plant for cold mixes type plant with electronic control using crushed aggregate of specified grading premixed with bituminous emulsion (MSD) at the rate of 5% (five) percent of mix transported to site within all leads laid over a previousioly prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per MORTH Technical Specificaton Section 500 and as per IRC:SP:100-2014 complete or as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax and other taxes imposed by the Government but excluding GST.

Providing and applying Tack Coat with bitumen emulsion (RS-I) including cleaning the road surface with hydraulic broom and spraying with emulsion pressure distributor at the rate of 0.225Kg. (Zero point two two five Kilogram) per Square metre on granular / bituminous surface as per MORD technical specifications section 500 or as directed by the Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and applying Tack Coat with bitumen emulsion (RS-I) including cleaning the road surface with hydraulic broom and spraying with emulsion pressure distributor at the rate of 0.275Kg. (Zero point two seven five Kilogram) per Square metre on prepared granular/ bituminious surface as per MORD technical specifications section 500 or as directed by the Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals .The rate is inclusive of octroi, royality ,Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing , Laying and rolling 30 mm (Thirty Millimeter) compacted thickness cold mix bituminous concrete with 75 (seventy five) TPH drum mix plant for cold mixes type plant with electronic control grading -II using crushed aggregate 13.2mm (thirteen decimal two millimetre) nominal size of specified grading premixed with bituminous emulsion (MSD) at the rate of 8% (Eight) percent of mix weight, using cement as filler with quantity not less than 2% (Two percent) by weight of total aggregate, transported to site laid with Censor paver finisher hydraulic with Censor conrol to the required grade, level and alignment over a previously prepared surface and rolling complete or pneumatic tyre roller of 12-15 (Tweleve to fifteen) tonne with type pressure of atleast 0.56 MPa (Zero decimal five six ) for intermediate rolling and finish rolling with 6-8 (six to eight) tonne smooth wheeled tandom roller to achieve the desire compaction as per MORTH technical specification section 500 as per the direction and entire satisfaction of Engineer In Charge including carriage of material within all leads, lifts and other incidentials. The rate is including octroi, Royality , Malkhana, Toll tax and other taxes imposed by the Goverment but exluding the GST.

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete in open foundation for all type of structure complete using grade M-10 (M-ten) nominal mix 1: 3: 6 ( One cement isto three sand isto six graded crushed/broken stone aggregate 20mm (twenty millimetre) nominal size on ground or under water and curing complete including pumping or bailing out water, dewatering removal of slush as required at site which may arrise at the time of laying concrete complete for all heights/ depths including the cost of form work as per drawings and M.O.R.D. technical specification section 800, 900 and 1200 as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government but excluding GST

Providing and fixing of typical PMGSY informatory sign board with logo as per M.O.R.D. specification and drawing . Three MS plates of 1.6 mm ( one point six millimetre) thick top and middle plate duly welded with MS flat iron 25mmx5mm ( twenty five millimetres into five millimetres) size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm (Twenty five millimetre into twenty five milimetres into five millimetre). The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 Nos. ( Two Nos.) 75mmx75mm (seventy five millimetre into seventy five millimetres) of 12 SWG (twelve standard wire gauge) sheet tubes posts duly embedded in cement concrete M-15 (M fifteen) nominal mix 1:2½ : 5 (One cement: Two and half sand: Five graded or crushed stone aggregate 40mm(Forty milimetres) grade blocks of 450mmx450mmx600mm ( four hundred fifty millimetres into four hundred fifty millimetres into six hundred millimetres), 600mm ( six hundred millimetres) below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mm (Forty seven millimetre into forty seven millimetres) of 12 SWG (Twelve standard wire gauge) steel plate tube. All MS will be stove enamelled on both sides. Lettering and printing arrows, borders etcetera will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing and M.O.R.D. technical specifications section 1700 and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST

Reinforced cement concrete M-15 (M-fifteen) grade 5th (fifth) Kilometre stone (Precast) of standard design as per IRC :8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Reinforced cement concrete M-15 (M-fifteen) grade Ordinary Kilometer Stone (Precast) of standard design as per IRC :8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Reinforced cement concrete M-15 (M-fifteen) grade 200m (two hundred metre) Stone (Precast) of standard design as per IRC :8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals.The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Reinforced cement concrete M-15 (M-fifteen) grade Boundary Pillar (Precast) of standard design as per IRC :25 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals.The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing of Retro-reflectorised Traffic Signs 900mm equilateral triangular (nine hundred milimetre) cautionary, mandatory and informatory sign board as per IRC:67 (IRC - sixty seven) made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm (one point five milimetre) thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (seventy five milimtetre into seventy five milimtre into six milimetre) firmly fixed to the ground by means of properly designed foundation with M15 (M-fifteen) grade cement concrete 450 mm x 450 mm x 600 mm, (four hundred fifty milimetre into four hundred fifty milimetre into six hundred milimetre), 600 mm (six hundred milimetre) below ground level as per drawings and MORD Technical Specification Section 1700 including painting angle iron post with primer and two coats of epoxy paint as per specification . The rate including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing of Retro-reflectorised Traffic Signs 600 mm circular (six hundred milimetre) cautionary, mandatory and informatory sign board as per IRC:67 (IRC - sixty seven) made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm (one point five milimetre) thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (seventy five milimtetre into seventy five milimtre into six milimetre) firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, (four hundred fifty milimetre into four hundred fifty milimetre into six hundred milimetre), 600 mm(six hundred milimetre) below ground level as per drawings and MORD Technical Specification Section 1700 including painting angle iron post with primer and two coats of epoxy paint as per specification . The rate including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing of Retro-reflectorised Traffic Signs 600mm equilateral triangular (Six hundred millimeter) cautionary, mandatory and informatory sign board as per IRC:67 (IRC - sixty seven) made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm (one point five milimetre) thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (seventy five milimtetre into seventy five milimtre into six milimetre) firmly fixed to the ground by means of properly designed foundation with M15 (M-fifteen) grade cement concrete 450 mm x 450 mm x 600 mm, (four hundred fifty milimetre into four hundred fifty milimetre into six hundred milimetre), 600 mm( six hundred milimetre) below ground level as per drawings and MORD Technical Specification Section 1700 including painting angle iron post with primer and two coats of epoxy paint as per specification. The rate including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing of Retro-reflectorised Traffic Signs 600x450mm Rectangular board (six hundred into four hundred fifty milimetre) cautionary, mandatory and informatory sign board as per IRC:67 (IRC - sixty seven) made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm (one point five milimetre) thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (seventy five milimtetre into seventy five milimtre into six milimetre) firmly fixed to the ground by means of properly designed foundation with M15 (M-fifteen) grade cement concrete 450 mm x 450 mm x 600 mm (four hundred fifty milimetre into four hundred fifty milimetre into six hundred milimetre), 600 mm( six hundred milimetre) below ground level as per drawings and MORD Technical Specification Section 1700 including painting angle iron post with primer and two coats of epoxy paint as per specification. The rate including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing of Retro-reflectorised Traffic Signs 800x600 mm Rectangular board (eight hundred into six hundred milimetre) cautionary, mandatory and informatory sign board as per IRC:67 (IRC - sixty seven) made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm (one point five milimetre) thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (seventy five milimtetre into seventy five milimtre into six milimetre) firmly fixed to the ground by means of properly designed foundation with M15 (M-fifteen) grade cement concrete 450 mm x 450 mm x 600 mm (four hundred fifty milimetre into four hundred fifty milimetre into six hundred milimetre), 600 mm( six hundred milimetre) below ground level as per drawings and MORD Technical Specification Section 1700 including painting angle iron post with primer and two coats of epoxy paint as per specification. The rate including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing of Retro-reflectorised Traffic Signs 900 mm Octagonal, (nine hundred ,milimetre) cautionary, mandatory and informatory sign board as per IRC:67 (IRC - sixty seven) made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm (one point five milimetre) thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (seventy five milimtetre into seventy five milimtre into six milimetre) firmly fixed to the ground by means of properly designed foundation with M15 (M-fifteen) grade cement concrete 450 mm x 450 mm x 600 mm (four hundred fifty milimetre into four hundred fifty milimetre into six hundred milimetre), 600 mm (six hundred milimetre) below ground level as per drawings and MORD Technical Specification Section 1700 including painting angle iron post with primer and two coats of epoxy paint as per specification. The rate including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and erecting Direction and Place Identification signs board upto 0.90 sqm (zero point nine zero square metre) retro-reflectorised sign board as per IRC:67 (IRC - sixty seven) made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm (two millimetre) thick, supported on mild steel angle iron post 75x75x6mm (seventy five into seventy five into six millimetre) firmly fixed to the ground by means of properly designed foundation with M-15 (M-fifteen) grade cement concrete 450 x 450 x 600 mm (four hundred fifty into four hundred fifty into six hundred millimetres), 600 mm (six hundred millimetre) below ground level as per approved drawing and M.O.R.D. Tehnical Specification Section 1700 including painting angle iron post with primer and two coats of epoxy paint as per specification. The rate including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and erecting Direction and Place Identification signs board more than 0.90 sqm (zero point nine zero square metre ) retro-reflectorised sign board as per IRC:67 (IRC - sixty seven) made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm (two millimetre) thick supported on mild steel angle iron post 75x75x6mm (seventy five into seventy five into six millimetre) firmly fixed to the ground by means of properly designed foundation with M-15 (M-fifteen) grade cement concrete 450 x 450 x 600 mm (four hundred fifty into four hundred fifty into six hundred millimetres), 600 mm (six hundred millimetre) below ground level as per approved drawing and M.O.R.D. Tehnical Specification Section 1700 including painting angle iron post with primer and two coats of epoxy paint as per specification. The rate including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing of typical PMGSY Logo sign board with Logo as per MORD specifications and drawing with ACP Sheet 3mm (three milimetre) thick fixed on MS angle 25mmx25mm x 3mm (twenty five milimetre into twenty five milimetre into three milimetre)size on back on edges. Vertical Post MS square tubes 80x80x4.80mm (eighty into eighty into four point eight zero milimetre) thick duly embedded with base plate 200x200x5mm (two hundred into two hundred into five milimetre)in cement concrete M-20 (M- twenty) grade blocks of Size 450mm x 450mm (four hundred fifty milimetre into four hundred fifty milimetre ), 600mm(six hundred milimetre), below ground level. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per MORD technical specification Section 1700 . Retro Reflective Sheet Type IV including cutting, printing, lettering & fixing complete in all respects. The rate including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and fixing Citizen Informatory sign board logo as per M.O.R.D. specification and drawing . Three MS plates of 1.6 mm ( one point six millimetre) thick top and middle plate duly welded with MS flat iron 25mmx5mm ( twenty five millimetres into five millimetres) size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm (Twenty five millimetre into twenty five milimetres into five millimetre). The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 Nos. ( Two Nos.) 75mmx75mm (seventy five millimetre into seventy five millimetres) of 12 SWG (twelve standard wire gauge) sheet tubes posts duly embedded in cement concrete M-15 (M fifteen) nominal mix 1:2½ : 5 (One cement: Two and half sand: Five graded or crushed stone aggregate 40mm(Forty milimetres) grade blocks of 450mmx450mmx600mm ( four hundred fifty millimetres into four hundred fifty millimetres into six hundred millimetres), 600mm ( six hundred millimetres) below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mm (Forty seven millimetre into forty seven millimetres) of 12 SWG (Twelve standard wire gauge) steel plate tube. All MS will be stove enamelled on both sides. Lettering and printing arrows, borders etcetera will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing and M.O.R.D. technical specifications section 1700 and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and Laying hot applied thermoplastic compound road marking paint 3mm (Three millimetre) thick with refletorising glass beads at the rate 250 gram (two hundred fifty) gram per square metre area, thickness of 3mm (Three millimetre) is exclusive of surface applied glass beads as per specificaiton and with strips of 0.10 (Zero decimal one) metre width in centre lines or edge lines of the road as per the directions of Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST

Provision of 8 (eight ) No.s rumble strips covered with premix carpet, 15-20 mm (fifteen to twenty milimetre)high at center, 250 mm (two hundred fifty milimetre) wide placed at 1m (one metre) centre to centre at approved locations to control speed), marked with white strips of road making paint. Taking ouput 100 sqm (one hundred square metre) (including gaps). The rate shall including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high (eighty to one hundred centimetre) above ground level, painted black and white in 15 cm (fifteen centimetre) wide strips, fitted with 80 x 100 mm (eighty into one hundred millimetre) rectangular or 75 mm dia (seventy five millimetre diametre) circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 and the drawings and specifications complete as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST

Providing and fixing of PMGSY Maintenance Information board as per MORD specifications and drawing with ACP Sheet 3mm (three milimetre) thick fixed on MS angle 25mmx25mm x 3mm (twenty five milimetre into twenty five milimetre into three milimetre) size on back on edges. Vertical Post MS square tubes 80x80x4.80mm (eighty into eighty into four point zero milimetre) thick with base plate 300x300x5mm (three hundred into three hundred into five milimetre) duly embedded in cement concrete M-20 grade blocks of Size 600mm x 600mm x 750mm (six hundred into six hundred into seven hundred fifty milimetre), 600 mm (six hundred milimetre) below ground level. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per MORD technical specification section 1700 . Retro Reflective Sheet Type IV including cutting, printing, lettering & fixing complete in all respects. (Providing & fixing of Maintenance Information Board) The rate shall including entire carriage of materials within all leads lifts and other incidentals and per direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and Fixing pavement marker (Cat eyes) made out of ABS 3 M (three M) plastic of size 128x110x29.5 mm ( one hundred twenty eight into one hundred ten into twenty nine decimal five millimetres) without nail having 50mm ( fifty millimetres) stem of ABS. The pavement marker shall be installed with epoxy ABS as per specification including carriage of materials and equipment with all mode of transportation and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST

Providing and laying mechanically mixed and vibrated plain cement concrete in sub structure grade M-15 (M-fifteen) design mix with cement contents not less than 275kg (two hundred seventy five kilogram per cubic metre) with 40mm (forty millimetre) nominal size graded stone aggregate on ground or under water including curing complete including pumping or bailing out water de-watering removal of slush as required at site, which may arises at the time of laying concrete complete for all heights/depths including cost of form work in parapets and toe wall etcetra as per drawing and MORD technical specification section 800, 900 and 1200 including carriage of materials within all leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government but excluding GST.

Providing and errecting a " W" metal beam crash barrier comprising of 3 mm (three millimetre) thick corrugated sheet metal beam rail, 70 cm (seventy centimetre) above road/ Ground level fixed on I.S.M.C. series channel vertical post 150 x 75 x 5 mm (one hundred fifty into seventy five into five millimetre) spaced 2 m (two metre) centre to centre 1.8 m (one point eight metre) high, 1.1 m (one point one metre) below ground/ road level, all steel part and fitments to be galvanised by hot dip process. All fitting to conforms to I.S 1367 and I.S. 1364 metal beam rail to be fixed on the vertical post with spacer of channel section 150x75x5mm (one hundred fifty into seventy five into five millimetre), 330 mm (three hundred thirty millimetre) long complete as per MORTH technical specification section 800 and as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete in open foundation for all type of structure complete using grade M-10 (M-ten) nominal mix 1: 3: 6 ( One cement isto three sand isto six graded crushed/broken stone aggregate 40mm (Forty millimetre) nominal size on ground or under water and curing complete including pumping or bailing out water, dewatering removal of slush as required at site which may arrise at the time of laying concrete complete for all heights/ depths including the cost of form work as per drawings and M.O.R.D. technical specification section 800, 900 and 1200 as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or other taxes imposed by the Government but excluding GST

Providing and laying mechanically mixed and vibrated concrete for plain cement concrete in sub structure using concrete grade M-20 ( M-Twenty) design mix with cement contents not less than 330 Kgs (Three hundred thirty kilograms) per cubic metre with 40mm (Forty milimetres) nominal size graded crushed stone aggregate as per drawings and M.O.R.D. technical specifications section 800, 900 & 1200 including the cost of form work and curing complete including carriage of materials within all kinds of leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete in sub-structure using grade M-20 ( M-Twenty) designed mix with cement contents not less than 350kg (three hundred fifty kilogram) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate as per drawings and M.O.R.D. technical section 800, 900 and 1200 including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in bed block and dirt wall etcetra and curing complete including carriage of materials with in all kinds of leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete in super structure as per drawing and M.O.R.D. technical specification section 800, 900 and 1400 using Reinforced Cement Concrete grade M-25 (M-Twenty five) designed mix with minimum cement contents not less than 400 Kgs(Four hundred kilogram) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate and curing complete including the cost of form work but excluding the cost of reinforcement for reinforced concrete work in deck slab, etcetera including carriage of material within all leads, lifts and other incidental, as per the directions of the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying mechanically mixed and vibrated reinforced cement concrete grade M-30 ( thirty ) designed mix with cement contents not less than 430 Kgs(Four hundred thirty kilogram) per cubic metre with 20mm(Twenty milimetres) nominal size graded crushed stone aggregate and curing complete as per drawing and M.O.R.D. technical specification section 800, 900,1000 and 1400 in wearing course including the cost of form work and the cost of reinforcement for reinforced concrete work complete including carriage of material within all leads, lifts and other incidental, as per the directions of the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Supplying fitting and placing HYSD bar reinforcement (Fe 500 D) in sub structure complete as per drawing and M.O.R.D. technical specifications section 1000 and 1200 including cutting, bending, binding and placing in position complete in all respect including cost of binding wire upto any height / depths as per the directions of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, or other taxes imposed by the Government but excluding GST.

Supplying fitting and placing HYSD bar reinforcement (Fe-500 D) in superstructure complete as per drawing and M.O.R.D. technical specifications section 1000 and 1400 including cutting, bending, binding and placing in position complete in all respect including cost of binding wire as per the directions of the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST.

Providing and laying (to level or slope) 900mm dia (Nine hundred millimetres) diameter reinforced cement concrete heavy duty non pressure pipes IS Class NP3 for culverts on first class bedding of granular material in single row including providing and fixing collar with cement mortar 1 : 2 ( One cement : two sand) but excluding the cost of excavation, protection works, back filling, concrete bedding and masonry work in head walls and parapets as per drawing and M.O.R.D. technical specifications section 1100 and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST

Painting of two coat including primer coat after filling the surface with synthetic enamel paint in all shades on new plastred/concrete surface as per MORD Technical Specification section 1700 and as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST

Construction of Reinforcement cement concrete railing of M-25 grade (M-twenty five) in cast in situ with 20mm (twenty millimetre) nominal size aggregate true to line and grade , tolerance of vertical railing post not to exceed 1 in 500 (one in five hundred) centre to centre spacing between vertical posts not to exceed 2000 mm (two thousand millimetre) leaving adequate space between vertical post for expansion complete including the cost of reinforcement, form work and curing complete as per approved drawing and MORD technical specifications section 800, 900, 1000 and 1200 and as per the entire satisfaction and as directed by the Engineer-in-charge including carriage of material within all leads, lifts other incidentals. The rate is including octroi, royality, Malkana, toll tax and any other taxes imposed by the Government but excluding GST.