Public Works Department Tender

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge asper clause 1500,1700 and 2100 including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge asper clause 1500,1700 and 2100.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shade Area of slab upto 0.50 sqm including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge

Garsa Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade.8mm thick (mirror polished and machine cut edge)Granite stone/Garsa tiles of any colour and shade including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 80mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. grass paver block of M-50 grade with approved color design and pattern including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge.

Steel work in Mild Steel built up tubular (round, 219.1*6.3mm dia hollow/circular hollow section etc. .) in columns etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. (equal or more than YST 210) including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge.

Steel work in built up Mild Steel tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes (YST 210) including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge.

Providing and fixing precoated galvanised iron profile plain sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 1518 microns using self drilling/ self tapping screws complete : Ridges plain (500 - 600mm) including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge.

Slate roofing with 7.5cm single lap single layer fixed on galvanised Precoated plain sheet (Steel work to be paid for separately) With Slates 40*20 cm size including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge.

Providing & Fixing ACP (Aluminium Composit panel) Sheet 3mm thick Ceiling Over MS Angle & T Section complete in all respect as per Engineer in charge including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge.

Fabrication, Supply and installation of the Art work at site in Shimla (Type-A) fabricated in Mild steel sheets of min. 1.5 mm in layers as per the drawing and then powder coated to minimum 20 micron, further coated with layer of glossy finish. The fabrication will require use of CNC machine in cutting metal sheets/ angles etc., welding suitably the sides with mild steel plates for giving 3 dimensional effect of layers (each layer min. 5cm thick), construction of sturdy inside frame of angles/ channels/ tubular sections. The finish should be acceptable standard and without allowing water inside the frame. It should be complete in all respect as per instructions of Engineer-in-Charge / fine arts supervisor. Changes in the Art work pattern and layering without any change in first/bottom layer area shall not constitute any change of scope. Suitable provision shall be made for attaching it with entry gate. Drawing part of this item including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge. ( 10unit 2.776sqmt each =27.76 sqmt )

Fabrication, Supply and installation of the Art workat site in Shimla (Type-B) fabricated in Mild steel sheets of min. 1.5 mm in layers as per the drawing and then powder coated to minimum 20 micron, further coated with layer of glossy finish. The fabrication will require use of CNC machine in cutting metal sheets/ angles etc., welding suitably the sides with mild steel plates for giving 3 dimensional effect of layers (each layer min. 5cm thick), construction of sturdy inside frame of angles/ channels/ tubular sections. The finish should be acceptable standard and without allowing water inside the frame. It should be complete in all respect as per instructions of Engineer-in-Charge / fine arts supervisor. Changes in the Art work pattern and layering without any change in first/bottom layer area shall not constitute any change of scope. Suitable provision shall be made for attaching it with entry gate. Drawing part of this item including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge. ( 20unit 1083.41*20=21668.20 sqcm)

Fabrication, Supply and installation of the Art work (Type-C) fabricated in Mild steel sheets of min. 1.5 mm in layers as per the drawing and then powder coated to minimum 20 micron, further coated with layer of glossy finish. The fabrication will require use of CNC machine in cutting metal sheets/ angles etc., welding suitably the sides with mild steel plates for giving 3 dimensional effect of layers (each layer min. 5cm thick), construction of sturdy inside frame of angles/ channels/ tubular sections. The finish should be acceptable standard and without allowing water inside the frame. It should be complete in all respect as per instructions of Engineer-in-Charge / fine arts supervisor. Changes in the Art work pattern and layering without any change in first/bottom layer area shall not constitute any change of scope. Suitable provision shall be made for attaching it with entry gate. Drawing part of this item including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge. (4unit 5.265*4= 21.06 sqmt)

Fabrication, Supply and installation of the Art work at site in Shimla (Type-D) fabricated in Mild steel sheets of min. 1.5 mm in layers as per the drawing and then powder coated to minimum 20 micron, further coated with layer of glossy finish. The fabrication will require use of CNC machine in cutting metal sheets/ angles etc., welding suitably the sides with mild steel plates for giving 3 dimensional effect of layers (each layer min. 5cm thick), construction of sturdy inside frame of angles/ channels/ tubular sections. The finish should be acceptable standard and without allowing water inside the frame. It should be complete in all respect as per instructions of Engineer-in-Charge / fine arts supervisor. Changes in the Art work pattern and layering without any change in first/bottom layer area shall not constitute any change of scope. Suitable provision shall be made for attaching it with entry gate. Drawing part of this item including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge. The sign board is not included in Art work (2unit 4.909*2=9.818sqmt )

Fabrication, Supply and installation of the Art work at site in Shimla (Type-E) fabricated in Mild steel sheets of min. 1.5 mm in layers as per the drawing and then powder coated to minimum 20 micron, further coated with layer of glossy finish. The fabrication will require use of CNC machine in cutting metal sheets/ angles etc., welding suitably the sides with mild steel plates for giving 3 dimensional effect of layers (each layer min. 5cm thick), construction of sturdy inside frame of angles/ channels/ tubular sections. The finish should be acceptable standard and without allowing water inside the frame. It should be complete in all respect as per instructions of Engineer-in-Charge / fine arts supervisor. Changes in the Art work pattern and layering without any change in first/bottom layer area shall not constitute any change of scope. Suitable provision shall be made for attaching it with entry gate. Drawing part of this item including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge. (2unit 3.060*2=6.12 sqmt)

Providing and fixing Solar power Pack of Capacity 1KWP i.e. 4 Nos 10W flood light & * Nos 6W LED light including Dust to down senser , Fright & Insurance, Packing Charges , Design and Engineering , development andpermission, PV Modules-250wp solar PV modules , 4.1 Inverter, 4.2 Mounting system fixed without tracking 4.3 Battery 150Ah 12 Volt and excluding Civil Work i.e. Minor earth movement, fence of security and tax etc. including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge.

Providing and fixing retroreflective Sign Board on 3mm ACP sheet with 3M/Avery demnsion tape of HP grade with complete back support and fixng as per the norms of the specification of MoRTH including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge. .

Providing and fixing Logo (back lit) as per the direction of Engineer-in-Charge (Min. Size 1.20 mtr dia )on Acrylic sheet of 2inch width as per drawing approved by Chief Architect including carriage by all mode of transportation to the entire satisfaction and direction of the Engineer-In Charge.

Add for Structural Design, drawings and Architect design and drawing Charges @ 4% as per entire satisfaction of Engineer-in-Charge.