Public Works Department Tender

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm (twenty milimetre) nominal size) upto plinth level with : Cement mortar 1:6 (one cement : six coarse sand) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Centering and shuttering including strutting, propping etc. and removal of form including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge. For

Foundations, footings, bases of columns,etc. for mass concrete.

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders,bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiralstaircasesStair cases with sloping or stepped soffits excluding landing

Edges of slabs and breaks in floors and walls Under 20 cm wide

Providing and laying in position cement concrete ofspecified grade excluding the cost of centering and shuttering . All work up to plinth level :1:5:10 (one cement : five coarse sand): ten graded stone aggregate 40 mm (forty milimetre) nominal size) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Poviding and laying in position cement concrete of specified grade excluding the cost of centering and shuttering- All work up to plinth level 1:4:8 (one cement : four sand : eight graded stone aggregate 20mm (twenty milimetre) nominal size.) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying in position specified grade ofreinforced cement concrete, excluding the cost ofcentering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (one cement :one point five sand : three graded stone aggregate 20mm (twenty milimetre) nominal size.) including carriage of material in all leads and lifts and other incidentals complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Reinforced cement concrete work in beams, suspendedfloors, roofs having slope up to 15° landings, balconies,shelves, chajjas, lintels, bands, plain window sills,staircases and spiral stair cases above plinth level up tofloor five level, excluding the cost of centering,shuttering, finishing and reinforcement with 1:1.5:3 (1cement : 1.5 coarse sand) : 3 graded stone aggregate20 mm nominal size). including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Reinforced cement concrete work in walls (anythickness), including attached pilasters, buttresses,plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. above plinth level up to floor all level, excluding cost of centering, huttering,finishing and reinforcement : 1:1.5:3 (one cement : one point five coarse sand : three graded stone aggregate 20 mm (twenty milimetre)nominal size) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing thermo mechanical teated bars of grade FE-500 D or more Steel reinforement for R.C.C. work including straightening, cutting, bending, placing in position and binding including cast of binding wire including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Brick work with common burnt clay machine mouldedperforated bricks of class designation 12.5 conforming toIS: 2222 in superstructure above plinth level up to all floor level in cement mortar 1:6 (one cement : six coarsesand) : With F.P.S.(non modular) bricks including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Half brick masonry with common burnt clay F.P.S. (nonmodular) bricks of class designation 7.5 insuperstructure above plinth level up to floor any level. including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing wood work in frames of doors, windows,clerestory windows and other frames, wrought framedand fixed in position with hold fast lugs or with dashfasteners of required dia & length ( hold fast lugs ordash fastener shall be paid for separately) for Sal wood including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 30 mm (thirty milimetre) thick factory made Polyvinyl Chloride(PVC) door shutter made of styles and railsof a uPVC hollow section of size 60x30 mm (sixty into thirty milimetre) and wall thickness 2 mm(two milimetre) (± 0.2 mm), withinbuilt decorative moulding edging on oneside. The styles and rails mitred and joint atthe corners by means of M.S. galvanised/plastic brackets of size 75x220 mm (seventy five into two hundred twenty milimetre) havingwall thickness 1.0 mm (one milimetre) and stainless steelscrews. The styles of the shutter reinforcedby inserting galvanied M.S. tube of size25x20 mm (twenty five milimetre into twenty milimetre) and 1 mm (one milimetre) (± 0.1 mm) wallthickness. The lock rail made up of 'H'section, a uPVC hollow section of size100x30 mm (one hundred into thirty milimetre) and 2 mm (two milimetre) (± 0.2 mm) wallthickness fixed to the shutter styles bymeans of plastic/ galvanised M.S. 'U' cleats.The shutter frame filled with a uPVC ultichamberedsingle panel of size not less than620 mm, having over all thickness of 20 mm (twenty milimetre) and 1 mm (one milimetre) (± 0.1 mm) wall thickness.The panels filled vertically and tie bar at twoplaces by inserting horizontally 6 mm(six milimetre) galvanised M.S. rod and fastened withnuts and washers, complete as permanufacturer's specification and direction ofEngineer-in-charge including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing panelled or panelled and glazedshutters for doors, windows and clerestory windowsfixing with butt hinges of required size with necessaryscrews, excluding panelling which will be paid forseparately,ll complete as per direction of Engineer-incharge.(Note:- Butt hinges and necessary screws shall be paidseparately)Second class teak wood 35 mm (thirty five milimetre) thick shutters including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing angle iron cupboard frames frames manufactured from M.S.Angle iron section 25X25X5mm (twenty five into twenty five into five milimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 25X25 mm (twenty five into twenty five milimetre)welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five milimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface (twenty five into twenty five into five milimetre)

Providing and fixing cup board shutters 25 mm (twenty five milimetre) thick,with Pre-laminated flat pressed three layer particle boardor graded wood particle board IS: 12823 marked,exterior grade (Grade l Type ll), having one sidedecorative lamination and other side alancinglamination, including IInd class teak wood lipping of 25mm (twenty five milimetre) wide x12 mm (twelve milimetre) thick with necessary screws and brightfinished stainless steel piano hinges, including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing wire gauge shutters usinggalvanized M.S. wire gauge of average width of aperture1.4 mm in both directions with wire of dia 0.63 mm ( zero point six three milimetre) , fordoors, windows and clerestory windows with hinges andnecessary screws 35 mm thick shutters Second class teak wood including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing Aluminium sheet 4 mm (four milimetre) thick composite panel having core of polythene fixed to internal side with screws or nails including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing M.S. grills of required pattern inframes of windows etc. with M.S. flats, square or roundbars etc. including priming coat with approved steelprimer all complete.Fixed to openings /wooden frames with rawlplugs screws etc including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing aluminium sliding door bolts, ISImarked anodised (anodic coating not less than gradeAC 10 as per IS : 1868), transparent or dyed torequired colour or shade, with nuts and screws etc.complete including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing aluminium tower bolts, ISI marked,anodised (anodic coating not less than grade AC 10 asper IS : 1868 ) transparent or dyed to required colour orshade, with necessary screws etc. complete including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

200x10mm (Two hundred x ten millimeter)

150x10mm (One hundred fifty x ten millimeter)

100x10mm (One hundred x ten millimeter)

Providing and fixing aluminium handles, ISI marked,anodised (anodic coating not less than grade AC 10 asper IS : 1868) transparent or dyed to required colour orshade, with necessary screws etc. complete including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

125 mm (One hundred x twenty five millimeter)

100 mm (One hundred millimeter)

75 mm (seventy five millimeter)

Providing and fixing bright finished brass 100mm.(One hundred millimeter) Mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing bright finished brass 100 mm (one hundred milimetre) mortice latch and lock, ISI marked, with six levers and apair of anodised (anodic coating not less than grade AC10 as per IS : 1868) aluminium lever handles approvedquality with necessary screws etc. including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing bright finished brass hard drawnhooks and eyes including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

250mm (Two hundred fifty millimeter)

200mm(Two hundred millimeter)

Providing and fixing bright finished brass hasp andstaple (safety type) with necessary screws etc. complete. 115mm (one hundred fifteen milimetre) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing bright finished brass single actingspring hinges with necessary brass screws etc.complete 150mm (one hundred fifty milimetre) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing cup board shutters with 25 mm (twenty five milimetre) thickveneered particle board IS : 3097 marked, exterior grade(Grade I), of approved make, including IInd class teakwood lipping of 25 mm (twenty five milimetre) wide x 12 mm (twelve milimetre) thick withWith non decorative veneering on both sidesnecessary screws and bright finished stainless steelpiano hinges, including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Cement concrete flooring 1:2:4 (one cement :two coarse sand : four graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm (forty milimetre) thick with 20 mm (twenty milimetre) nominal size stone aggregate including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Precast terrazo tiles 22 mm (twenty two milimetre) thick with graded marblechips of size upto 12 mm (twelve milimetre) , laid in floors, and landings,jointed with neat cement slurry mixed with pigment tomatch the shade of the tiles, including rubbing andpolishing complete, on 20 mm (twenty milimetre) thick bed of cementmortar 1:4 (one cement: four coarse sand) :11.16.2 Medium shade pigment using 50% whitecement and 50% ordinary cement including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) withwater absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours and shades, laidon 20mm (twenty milimetre) thick cement mortar 1:4 (one cement : four coarsesand), jointing with grey cement slurry @ 3.3 kg/ sqm three point three kilogram per square metre) including grouting the joints with white cement andmatching pigments etc., complete11.49.2 Size of Tile 600x600 mm (six hundred into six hundred milimetre) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying vitrified floor tiles in different sizes(thickness to be specified by the manufacturer) withwater absorption less than 0.08% and conforming to IS:15622, of approved make, in all colours and shades, laidon 20mm (twenty milimetre) thick cement mortar 1:4 (one cement : four coarsesand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement andmatching pigments etc., complete11.49.2 Size of Tile 600x600 mm (six hundred into six hundred milimetre) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 10 mm (ten milimetre) thick acid and/or alkaliresistant tiles of approved make and colour using acidand/or alkali resisting mortar bedding, and joints filledwith acid and/or alkali resisting cement as per IS : 457,11.21.2 In dado/skirting on 12 mm (twelve milimetre) thick mortar 1:4(one acid proof cement : four coarse sand)11.21.2.1 Acid and alkali resistant tile sqm 1437.10 including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 10 mm (ten milimetre) thick acid and/or alkaliresistant tiles of approved make and colour using acidand/or alkali resisting mortar bedding, and joints filledwith acid and/or alkali resisting cement as per IS : 4457,complete as per the direction of Engineer-in- ChargeIn flooring on a bed of 10 mm (ten milimetre) thick mortar1:4 (one acid proof cement : four coarse sand) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying Pre-Laminated Particle Board 12 mm (twelve milimetre) thick ply panelling over soft wood frame 40 x 40 mm (forty into forty milimetre) @ 600 x 600 mm c/c (six hundred into six hundred milimetre center to center) having decorative first class kiln seasoned teak wood polished beeding out of 25 x 12 mm (twenty five into twelve milimetre) and cornice of size75 x 60 mm (seventy five into sixty milimetre) with necessary screws priming coat on unexposed surface etc for all floor level including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying Black granite stone in flooring 20mm (twenty miulimetre) (average)thickness base of cement mortar 1:3(one cement: three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing for all foor level including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Kota stone slab flooring over 20 mm (twenty milimetre) (average) thickbase laid over and jointed with grey cement slurry mixedwith pigment to match the shade of the slab, includingrubbing and polishing complete with base of cement mortar 1 : 4 (one cement : four coarse sand) :25 mm (twenty milimetre) thick including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Kota stone slabs 20 mm (twenty milimetre) thick in risers of steps, skirting,dado and pillars laid on 12 mm (twelve milimetre) (average) thick cementmortar 1:3 (one cement: three coarse sand) and jointed withgrey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

40 mm (forty milimetre) thick fine dressed stone flooring over 20 mm (twenty milimetre) (average) thick base of cement mortar 1:5 (one cement : five coarse sand) with joints finished flush including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing corrugated G.S. sheet roofing includingvertical / curved surface fixed with polymer coated J or Lhooks, bolts and nuts 8 mm (eight milimetre) diameter with bitumen andG.I. limpet washers or with G.I. limpet washers filled withwhite lead, including a coat of approved steel primer andtwo coats of approved paint on overlapping of sheetscomplete (up to any pitch in horizontal/ vertical or curvedsurfaces), excluding the cost of purlins, rafters andtrusses and including cutting to size and shape whereverrequired.0.63 mm (zero point six three milimetre) thick with zinc coating not less than 275 gm/ m² (two hundred seventy five graams per metre square including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing ridges or hips of width 60 cm (sixty centimetre) overall widthplain G.S. sheet fixed with polymer coated J or L hooks,bolts and nuts 8 mm dia G.I. limpet and bitumenwashers complete.0.63 mm (zero point six three milimetre) thick with zinc coating not less than275 gm/m² (two hundred seventy five grams per metre square) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing valleys of 90 cm (ninety centimetre) wide overall in plain G.S.sheet fixed with polymer coated J, or L hooks, bolts andnuts 8 mm (eight milimetre) dia G.I. limpet and bitumen washerscomplete including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing flushing 38cm(Thirty centimeter) overall with 0.60mm ( Zero point six milimetre)thick pre painted sheet in roofing with hot dipped metallic Zink coated sheet with top coat of regular modified polyester organic coating of 20 (twenty) microns over 5 (five) microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with pre painted J or L hooks, bolts and nuts 6mm(Six milimetre) dia meter & pre painted G.I. limpet & bitumen washers complete with all accessories as required including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing on wall face unplasticised - PVCmoulded fittings/ accessories for unplasticised RigidPVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382,leaving 10 mm (ten milimetre) gap for thermal expansion110 mm one hundred milimetre) diameter including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing on wall face unplasticised - PVCmoulded fittings/ accessories for unplasticised RigidPVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382,leaving 10 mm (ten milimetre) gap for thermal expansion110 mm one hundred milimetre) diameter including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

110 mm (one hundred ten milimetre) bend

Shoe 100mm dia(One hundred milimetre) dia.

Providing and fixing M.S B.P sheet 1.66 mm to 2mm ( One point sixty six milliMetre to two millimetre) thick in eaves board/facia/soffits/ceiling including cutting , fixing and welding to steel roof members and applying a coat of red lead primer complete as per the direction of the Engineer-in-Charge (base member of steel work shall be measured and paid for separately) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge..

Structural steel work riveted, bolted or welded in built up sections, Trusses and trussed partions in building work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.primer all complete

Steel work welded in built up section/ framed work in grating framed guard bars, ladder, railing, bracket and similar work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing hand rail of approved size bywelding etc. to steel ladder railing, balcony railing,staircase railing and similar works, including applyingpriming coat of approved steel primer E.R.W. tubes 113.80 kg one hundred thirteen milimetre including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20 mm X10 mmX2mm (twenty into ten into two milimetre) and braced with flat iron diagonals 20 mm X 5 mm (twenty into five milimetre) size with top and bottom rails of T.iron 40 mm X40 mm X6 mm (forty into forty into six milimetre ) with 38 mm (thirty milimetre) dia steel pulley complete with bolts and nuts locking arrangements, toppers,handles,including applying a priming coat of red lead paint including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

6 mm (six milimetre) cement plaster of mix: 1:3 (one cement : three fine sand) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

15 mm cement plaster on rough side of single or halfbrick wall of mix: 1:6 (one cement: six coarse sand) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

15 mm (fifteen milimetre) cement plaster on the rough side of single or half brick wall of mix 1:6 (one cement : six fine sand) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and applying plaster of paris putty of 2 mm (two milimetre) thickness over plastered surface to prepare the surface even and smooth complete including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade two or more coats on new work including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Distempering with dry distemper of approved brand andmanufacture (two or more coats) of required shade onnew work, over and including water thinnable primingcoat to give an even shade including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Applying priming coat With ready mixed pink or Grey primer ofapproved brand and manufacture on woodwork (hard and soft wood) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Painting with oil type wood preservative of approved brand and manufacture including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Applying priming coat overWith ready mixed red oxide zinc chromateprimer of approved brand and manufactureon steel galvanised iron/ steel works including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’sspecifications including appropriate priming coat,preparation of surface, etc. complete.On steel work

Making plinth protection 50mm (fifty milineter) thick of cement concrete 1:3:6 (one cement : three coarse sand (zone-III) : six graded stone aggregate 20mm (twenty milimetre) nominal size) over 75mm (seventy five milimetre) thick bed of dry brick ballast 40mm (forty milimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing, laying and jointing glazed stoneware pipesclass SP-1 with stiff mixture of cement mortar in theproportion of 1:1 (one cement : one fine sand) includingtesting of joints etc. complete 150 mm (one hundred fifty milimetre) diameter including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing false ceiling at all height includingproviding and fixing of frame work made of specialsections, power pressed from M.S. sheets andgalvanized with zinc coating of 120 gms/sqm (one hundred twenty grams per square metre (both sidewith intermediate G.I. channels 45x15x0.9 mm (forty five into fifteen into zero point nine milimetre) runningat the spacing of 1200 mm (one thousand two hundred miloimtre) centre to centre, to which theceiling section 0.5 mm (zero point five milimetre) thick bottom wedge of 80 mm (eighty milimetre) with tapered flanges of 26 mm(twenty six milimetre) each having lips of 10.5mm (ten point five milimetre) , at 450 mm (four hundred fifty milimetre) centre to centre, shall be fixed in adirection perpendicular to G.I. intermediate channel withconnecting clips made out of 2.64 mm (two point six four milimetre) dia x 230 mm two hundred thirty milimetre ) long G.I. wire at every junction, including fixing perimeterchannels 0.5 mm (zero point five milimetre) thick 27 mm (twenty seven milimetre) high having flanges of 20mm (twenty milimetre) and 30 mm(thirty milimetre) long, the perimeter of ceiling fixed towall/partition with the help of rawl plugs at 450 mm (four hundred fifty milimetre) centre, with 25mm (twenty milimetre) long drywall screws @ 230 mm (two hundred thirty milimetre) interval, including fixing ofgypsum board to ceiling section and perimeter channelwith the help of dry wall screws of size 3.5 x 25 mm at230 mm c/c, (three point five into twenty five milimetre at two hundred thirty milimetre center to center) including jointing and finishing to a flushfinish of tapered and square edges of the board withrecommended jointing compound , jointing tapes ,finishing with jointing compound in 3 (three layers coveringupto 150 mm (one hundred fifty milimetre) on both sides of joint and two coats ofprimer suitable for board, all as per manufacturer'sspecification and also including the cost of makingopenings for light fittings, grills, diffusers, cutouts madewith frame of perimeter channels suitably fixed, allcomplete as per drawings, specification and direction ofthe Engineer in Charge but excluding the cost of paintingwithinclusive) as per IS : 277 and consisting of angle cleatsof size 25 mm (twenty five milimetre) wide x 1.6 mm (one hundred six milimetre) thick with flanges of 27mm (twenty seven milimetre) and 37mm (thirty seven milimetre) , at 1200 mm (one thousand two hundred milimetre) centre to centre, one flangefixed to the ceiling with dash fastener 12.5 mm (twelve point five milimetre) dia x50mm (fifty milimetre) long with 6mm dia bolts, other flange of cleatfixed to the angle hangers of 25x10x0.50 mm (twenty five into ten into zero point five zero milimetre) of requiredlength with nuts & bolts of required size and other end ofangle hanger fixedFully Perforated Gypsum Plaster Board ofsize 1200 x 2400x12.5 mm (one thousand two hundred into two thousand four hundred into twelve point five milimetre) having approx.15 % perforated area with perforation sizeand pattern as approved by the Engineerinchargeand as per manufacturer's specification, with all 4 (four) side tapered andbacked by acoustical tissue with NRC valuenot less than 0.60 including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

15mm (fifteen milimetre) nominal bore

20 mm (twenty milimetre) nominal bore

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-incharge.1216 (16 mm (sixteen milimetre) OD) pipe including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Constructing masonry Chamber 30x30x50 cm (thirty into thirty into fifty milimetre) inside, in brick work in cement mortar 1:4 (one cement : four coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (one hundred into one hundred (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (one cement : two coarse sand : four graded stone aggregate twenty mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (one cement : five fine sand : ten graded stone aggregate 40mm (forty milimetre) nominal size ) and inside plastering with cement mortar 1:3 (one cement : three coarse sand) 12mm (twelve milimetre) thick, finished with a floating coat of neat cement complete as per standard Design:With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm (one hunderde milimetre) sand cast Iron P or S trap, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:Stainless Steel AISI-304(18/8) Orissa pattern W.C. pan of size 585x480 mm (five hundered eighty five into four hundered eighty milimetre) with flush pipe and integrated type foot rests including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 (ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT White colour high density polyethylene / poly propylene 10 (ten) litres capacity ( full flush) European standard control low level flushing cistern No. 2602 of Cera/Hindware/jaguar with fittings with a pair of brackets with fittings such a lead valve, syphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia C.P. flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) .as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing wash basin with C.I. brackets, 15 mm (fifteen milimetre) C.P. brass pillar taps, 32 mm (THIRTY TWO MILIMETRE) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm ( five hundred fifty into four hundred milimetre) with single 15 mm (fifteen milimetre) C.P. brass pillar tap including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

.Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm (forty milimetre) C.P brass waste and 40mm (forty milimetre) C.P. brass trap withnecessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :Size 600x450x200 mm (six hundered into four hundered fifty into two hundred milimetred) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing CP Brass 32mm (thirty two milimetre) size bottlw trap of aproved quality & makeand as per direction of engineer- in- charge including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :32 mm (thirty two milimetre) nominal bore including carriage of material in all leads and lifts and other incidentials including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 600x450 mm (six hundred into four hundred fifty milimetre) beveled edge mirror of superior glass (of approved quality) complete with 6 mm (six milimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT towl rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.600 mm (six hundered milimetre) long towel rail with total length of 645 mm (six hundred forty five milimetre) , width 78 mm (seventy eight milimetre) and effective height of 88 mm (eighty eight milimetre) , weighing not less than 190 gms.(one hundred ninety grams) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing toilet paper holder C.P. brass including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT liquid soap container 109 mm (one hundred nine milimetre) wide, 125 mm (one hunderd twenty five milimetre) high and 112 mm (one hunderd twelve milimetre) distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms (one hundred five grams) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm (one hunderd thirty eight milimetre) , breadth 102mm (one hundered two milimetre) , height of 75mm (seventy five milimetre) with concealed fitting arrangements, weighing not less than 106 gms. (one hundered six milimetre) including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :15 mm (fifteen milimetre) nominal bore including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms (six hunderde ninty grams) .15 mm (fifty milimetre) nominal bore including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing brass stop cock of approved quality 15 mm (fifteen milimetre) nominal bore including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PTMT bib cock of approved quality and colour.15mm (fifty milimetre) nominal bore, 86 mm (eighty six milimetre) long, weighing not less than 88 gms including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing uplasticised PVC connection pipe with brass unions :15 mm (fifty milimetre) nominal bore including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

15 mm (fifteen millimetre) nominal bore

20 mm (twenty millimetre) nominal bore

25 mm (Twenty Five Millimetre) nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete.110x90 mm (one hundred ten x ninty millimetre) as per the direction of Engineer-in-charge including carriage of materials with in all leads, lifts and other incidentals including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing soil, waste and vent pipes including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

100 mm (one hundred milimetre) dia Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989

75 mm (seventy five milimetre) diaCentrifugally cast (spun) iron socketed pipe as per IS: 3989

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC single equal branch with oval access door, ISI marked insertion rubber washer 3 mm (three millimetre) thick bolts and nuts complete /including fixing with approved adhesive etc.including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC door bend with oval access door insertion rubber washer 3 mm Three millimetre) thick bolts and nuts ISI market complete including fixing with approved adhesive etc. including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC plain bends ISI marked including fixing with approved adhesive etc. including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing 110 mm ( one hundred ten millimetre) dia PVC clamps ISI marked of approved design with steel screws and rawal plugs etc. including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and laying cement concrete 1:5:10 (one cement : five coarse sand : ten graded stone aggregate 40 mm (forty milimetre) nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :150 mm (one hundred fifty milimetre) diameter S.W. pipe including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm (three hundred into three hunderde milimetre) size (inside) the weight of cover to be not less than 4.50 kg (four point five zero kilogram ) and frame to be not less than 2.70 kg (two point seven zero kilogram) as per standard design:With sewer bricks conforming to IS : 4885 including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement : four coarse sand ) with R.C.C. top slabwith 1:1.5:3 mix (one cement : one point five coarse sand (zone- III) : three graded stone aggregate 20 mm (twenty milimetre) nominal size), foundation concrete 1:4:8 mix (one cement : four coarse sand (zone- III) : eight graded stone aggregate 40 mm (forty milimetre) nominal size), inside plastering 12 mm(twelve milimetre) thick with cement mortar 1:3 (one cement : three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (twenty milimetre) nominal size) finished with a floatingcoat of neat cement complete as per standard design Inside size 90x80 cm (ninety into eighty centimetre) and 45 cm (foty five centimetre) deep including C.I. cover with frame (light duty) 455x610 mm (four hundred fifty five into six hundred ten milimetre) internal dimensions, total weight of cover and frame to be not less than 38 kg (thirty eight kilogram) (weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) ) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of material in all leads and lifts and other incidentials complete and as per the entire satisfaction and direction of Engineer-in-Charge.