NHPC Limited Tender

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Floors etc.upto 200mm. in thickness.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Columns, pillars, posts and struts ; Square, rectangular or polygonal in plan.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Beams, cantilever, girders and lintels.: Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 Mtr. in depth in all heights from floor.

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in: Sloping or battering surfaces including folded plates: Where inclination to horizontal plane does not exceed 30 degree

Providing and laying cement concrete 1:1.5:3 (1cement :1.5 sand :3 graded stone aggregate 20mm. nominal size) and curing complete excluding cost of form work and reinforcement for feinforced concrete work in: Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor two level.

Providing and laying cement concrete work 1:1.5:3 (1 cement : 1.5 sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in : Lintels, beams girders bressumers and cantilevers upto floor two level :

Providing and laying cement concrete work 1:1.5:3 (1 cement : 1.5 sand :3 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in : Columns, pillars, posts and struts

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level : Tor Steel :

Brick work using common burnt clay building bricks in foundation and plinth in: Cement Mortar 1:6 (1 cement: 6 sand) second class bricks

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:6

6mm Cement plaster to ceiling (b) In Cement Mortar 1:4(1 Cement:4 Sand)

Distempering with dry distemper of approved brand and manufacture(Two coats)and of required shade on undecorated wall surface to given an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth.

Providing and fixing Garsa stone 12mm.cladding on R.C.C.surface side as on faces of Arch masonry walls etc.on 12mm. thick cement plaster 1:3 (1cement:3sand) and jointed with cement slurry i/c scaffolding etc. complete.

Steel work welded in built up sections, trusses and framed work, including cutting , hoisting , fixing in position and applying a priming coat of red lead paint . In trusses and trussed purlins in buildings.

Providing and fixing Anodised Aluminium work for door, window, ventilators and partitions with extruted builtup standard tubular and other sections of approved make confirming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868(Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions at top, bottoms and sides with required PVC/reoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and joined mechanically whereever required including cleast angle, aluminium snap beading for glazings/panelling C.P. brass/stainless steel srews. All complete as per architectural drawings and the directions of Engineer-in-Charge:- For door, windows and ventilators and glazed partitions frame.

Providing and fixing Anodised Aluminium work for door, window, ventilators and partitions with extruted builtup standard tubular and other sections of approved make confirming to IS 733 and IS 1285 anodised transparent or dyed to required shade according to IS 1868(Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions at top, bottoms and sides with required PVC/reoprene felt etc. Aluminium sections shall be smooth, rustfree, straight, mitred and joined mechanically whereever required including cleast angle, aluminium snap beading for glazings/panelling C.P. brass/stainless steel srews. All complete as per architectural drawings and the directions of Engineer-in-Charge. For shutters of doors windows & ventilators including providing and fixing hinges/pivots and making provisions for fixing of fittings

Providing and fixing glazing in Aluminium door, windows, ventilators, shutters and partition etc. with PVC/neoprens. Gasket etc complete as per the architectural drawing and the direction of Engineer-in-Charge(Cost of Aluminium snap beading shall be paid in basic item). Glazing with glass panes of 5.50mm thickness (weight not less than 13.75 kg/ sqm.

Providing and fixing aluminium tower bolts(berrel type) anodized trans parent or dyed to required shade and colour with screws etc. Complete.Size - 200x10mm

Providing and fixing aluminium handles anodysed transparent or dyed to required colour of shade with necessary screws etc. complete.100 mm