Indo Tibetan Border Police Tender

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

6 mm cement plaster of mix : 1:3 (1 cement : 3 fine sand)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre

Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Centering and shuttering including strutting,proppingetc. andremoval of formworkfor : columns,piers, abutments, pillars, posts and struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :Kitchen sink with drain board 510x1040 mm bowl depth 225 mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe 40 mm dia

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 20 mm nominal dia Pipes

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 15 mm nominal bore

Providing and fixing PTMT grating of approved quality and colour.Circular type 125 mm nominal dia with 25 mm waste hole

Kitchen cabinet : providing and fixing kitchen cabinets ,made out of 19mm hdhmr board for verticals, top, bottom and intermediate drawing. Back and top cabinet should be finished with 6mm thick Plywood Waterproof (BWP). Outer shutters are made out of 19mm board. Handles shall be of approved make and design. Skiriting : 100x19mm ply for skiriting all external /visible surface including top/back if exposed , shall be finished with 1.0mm acrylic of approved make shade. All internal surface of cabinet including top of shelves, sides etc. base box Action Tesa HDMR 18mm thick with acrylic and outerside white finish. Hings soft close. Hettich brand. Handless with complete accessories. • Panel doors thickness 19mm, • Stainless steel perforated Sheet Modular Kitchen Basket/Storage Basket (size 20”x24” ) of approved, With Labour and fitting.

Supply and installation of Kitchen Chimney with buffle filter of approved brand as per directed by Engineer-in-charge.Items Industrial Kitchen Chimney, Materials of Chimney Stainless Steel 304, Materials of Blower Body Stainless Steel 304, Materials of Blower Blade Stainless Steel 304, Materials of Exhaust pipe Aluminium, Shape Rectangular, Filter Type Baffle Filter, Control panel Type Push Button, Mount Type Wall Mounted, Exhaust/Flexible pipe (3 meter) Yes, Oil Pad Provided Yes, Chimney Air Suction Capacity (cubic meters per hour) 10000, Exhaust Motor RPM 2000 rpm, Blower Size 20, Chimney Power Cord Wire Length { Meter )20, Blower Motor Power 2000, Thickness of Chimney Sheet ( In MM )0.8, Chimney Height ( In CM )150 ,Chimney Length ( In CM ) 300, Chimney Width ( In CM )150, Suction Area Length ( In CM )290, Suction Area width ( In CM )140, Exhaust Area Length ( In CM )500, Exhaust Area Width ( In CM )500, Flexible Pipe Diameter ( In MM )150, Oil Collector Pad Length ( In CM )285, Oil Collector Pad Width ( In CM )135,Oil Collector Pad Thickness ( In CM )10