Indian Institute Of Management Tender

Round Pouf Size - Ø 450 x 450 H MM Seat Height- 450 mm • Structure made up of polyurethane foam block of approved quality supported with 16-18 mm BWP Ply confirming to IS 710:2010 at the bottom to fasten 50X25 mm nylon glides below it. • Approved PU foam to have density of = 40 having premium grade with moderate resilience. • Covered with removable Polyester fabric. • Martin - Dale Abrasion resistance 25000 to 30000 Cycles • Color fastness to lighting - 4 • Composition - Polyester - 100% • Weight not less than 360 GSM • Bottom Feet 50 X 25 mm nylon glides below it.

Round Cushions Size- 600 Dia x 80 H MM • Structure made up of polyurethane foam block of approved quality • Approved PU foam to have density of = 40 having premium grade with moderate resilience. • Covered with removable Polyester fabric. • Martin - Dale Abrasion resistance 25000 to 30000 Cycles • Color fastness to lighting - 4 • Composition - Polyester - 100% • Weight not less than 360 GSM

Coffee Table Rectangle Size - 1200 W x 600 D x 450 H MM • Table top shall be made in 18 mm BWP Ply confirming to IS 710:2010 with 1mm thick decorative laminate on the top and 0.6 mm thick balance lamination on bottom side of approved shade. Exposed edges covered with 2mm thick edge bending with using hot melt EVA glue • Powdercoated base in Trirod Pattern made up of 18 mm dia MS Bar of approved shade and color with coating thickness 60 micron with proper treatment. Buffers should be provided at contact point with floor. • The minimum factor of safety considered is 1.65 on yield stress.The allowable deflection will be limited to span/200.

Coffee Table Rectangle Size - 900 W x 600 D x 450 H MM • Table top shall be made in 18 mm BWP Ply confirming to IS 710:2010 with 1mm thick decorative laminate on the top and 0.6 mm thick balance lamination on bottom side of approved shade. Exposed edges covered with 2mm thick edge bending with using hot melt EVA glue • Powdercoated base in Trirod Pattern made up of 18 mm dia MS Bar of approved shade and color with coating thickness 60 micron with proper treatment. Buffers should be provided at contact point with floor. • The minimum factor of safety considered is 1.65 on yield stress.The allowable deflection will be limited to span/200.

Coffee Table Square Size - 600 W x 600 D x 450 H MM • Table top shall be made in 18 mm BWP Ply confirming to IS 710:2010 with 1mm thick decorative laminate on the top and 0.6 mm thick balance lamination on bottom side of approved shade. Exposed edges covered with 2mm thick edge bending with using hot melt EVA glue • Powdercoated base in Trirod Pattern made up of 18 mm dia MS Bar of approved shade and color with coating thickness 60 micron with proper treatment. Buffers should be provided at contact point with floor. • The minimum factor of safety considered is 1.65 on yield stress.The allowable deflection will be limited to span/200.

Book Tub: Supplying and Placing in place Book Tub of Dimension Size- 700 W x 700 D x 600 H MM of Following specifications: • Structure shall be made in 18 mm BWP Ply confirming to IS 710:2010 with 1mm thick decorative laminate on the visible surface and 0.6 mm thick balance lamination onunvisible sides of approved shade. Exposed edges covered with 2mm thick edge bending with using hot melt EVA glue . The entire structure is to be mounted on buffer. • Complete modular structure with minifix joinery. • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Bucket Chair: Supplying and Placing in place Arm Chair of Size - 650 W x 630 Dx 780 H MM Seat Height 450 mm. Chair Shall be made up of Single moulded high density PU foam with metal under structure upholstered with commercial grade approved fabric for the seat. Base to be made up steam beech wooden frame and legs, properly seasoned and chemically treated finished with PU polish matching to approved tone of the furnitures. Seat to be connected with frame with approved hardware including nuts and bolts. Commercial Grade fabric (as per approved shade) made up of 100% polyester, having GSM more than 360 with abrasion resistance 25000 to 30000 counts and colour fastness at scale 4. • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Carrel Double Seating: Supplying and Placing in Carrel -Double Seating of Size - 934 W x 1217 D x 1350 H MM Complete Structure made up of 18 mm BWP Ply confirming to IS 710:2010 including with 1mm thick decorative laminate IS 2046 : 1995 on both side matching with tabletop and balancing laminate of 0.6 mm thick of approved shade. Table top height shall be 750 mm.Modesty panel shall be provided between two desks in bottom and top. All edges finished with polypropylene edge bands 2 mm thick fixed with hot melt EVA glue with corner and edge rounding, enabling zero sharp elements environment. Complete structure with minifix joinery. Flip up box having one power port and one USB convertible port with metal raceway along with vertical and horizontally run for wire with junction box shall be provided. • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Carrel Single Seating: Supplying and Placing in Carrel -Double Seating of Size - 934 W x 617 D x 1350 H MM Complete Structure made up of 18 mm BWP Ply confirming to IS 710:2010 including with 1mm thick decorative laminate IS 2046 : 1995 on both side matching with tabletop and balancing laminate of 0.6 mm thick of approved shade. Table top height shall be 750 mm.Modesty panel shall be provided between two desks in bottom and top. All edges finished with polypropylene edge bands 2 mm thick fixed with hot melt EVA glue with corner and edge rounding, enabling zero sharp elements environment. Complete structure with minifix joinery. Flip up box having one power port and one USB convertible port with metal raceway along with vertical and horizontally run for wire with junction box shall be provided. • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Carrel Double Seater (PHD Student): Supplying and Placing in Carrel -Double Seating of Size - 1200 W x 1800 D x 1800 H MM Complete Structure made up of 18 mm BWP Ply confirming to IS 710:2010 with working table top of 25 mm thickess and 1mm thick decorative laminate IS 2046 : 1995 on both sides matching with tabletop and balancing laminate of 0.6 mm thick of approved shade. Table top height shall be 750 mm. Modesty panel shall be provided between two desks in bottom and top. Carrel shall have lockable storage shutters with SS handle in top modesty. It shall have fixed LED study light in bottom of open shelve for each seating. Suitable arrangement is to be made in front of open shelve for holding removable name plate. Front modesty shall be provided with pin up fabric board. All edges finished with polypropylene edge bands 2 mm thick fixed with hot melt EVA glue with corner and edge rounding, enabling zero sharp elements environment. Complete structure with minifix joinery. Each sides shall be provided with flip up box having 2x6 Amp. power port and light switch with raceway along with vertical and horizontal run for wire with junction box. • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Carrel Single Seater (PHD Student): Supplying and Placing in Carrel -Double Seating of Size - 1200 W x 900 D x 1800 H MM Complete Structure made up of 18 mm BWP Ply confirming to IS 710:2010 with working table top of 25 mm thickess and 1mm thick decorative laminate IS 2046 : 1995 on both sides matching with tabletop and balancing laminate of 0.6 mm thick of approved shade. Table top height shall be 750 mm. Modesty panel shall be provided in bottom and top. Carrel shall have lockable storage shutter with SS handle in top modesty. It shall have fixed LED study light in bottom of open shelve. Suitable arrangement is to be made in front of open shelve for holding removable name plate. Front modesty shall be provided with pin up fabric board. All edges finished with polypropylene edge bands 2 mm thick fixed with hot melt EVA glue with corner and edge rounding, enabling zero sharp elements environment. Complete structure with minifix joinery. Carrel shall be provided with flip up box having 2x6 Amp. power port and light switch with raceway along with vertical and horizontal run for wire with junction box. • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Chair : Providing & Placing in position Chair as approved of Size 570 W x 530 D x 1000 H MM Seat Height - 450 H mm Seat Back in Mesh of approved color with curved design and seat are made up of 12mm hot pressed plywood upholstered in fabric and moulded in foam. The High Resilience Polyurethane foam is moulded with density=45+/-2 kg/m3 and hardness load 16+/-2 kgf as per IS: 7888 for 25% compression. The seat and back are arrested together with a 9.0cm (W) spine made of 0.8cm thick HR steel. The back plywood shall be designed with contoured lumbar support for extra comfort. The chair shall have an center tilt mechanism and tilt tension adjustment, single locking facility and full 360 degrees swivel mechanism, the one piece arm rest should be made up of black integral skin polypropylene with 50-70 Shore “A” hardness reinforced with MS insert, the armrest are scratch and whether resistant. The arm rests are fitted to the seat with a connecting strip assembly made of 5mm of HR steel. The prong (base) is made of chrome plated steel and fitted with 5nos. twin wheel castors (castor wheel dia. 50mm). The prong (base) is 660mm pitch center dia (700mm with castors). The telescopic bellows is 3 piece telescopic type and injection molded in black polyurethane. Seat maximum height is 540mm & minimum height is 440mm & back height from floor maximum height is 1100mm & minimum height is 1000mm. Gas lift 100 mm telescopic haudraulic. • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Conference Table (08 Seater): Providing and fixing in position of customised ( factory made) Conference table of required Size- 2400 W x 1200 D x 750 H MM Table top shall be made out of 25mm thick commercial ply of BWP Grade confirming to IS 710:2010,including with 1mm thick decorative laminate IS 2046 : 1995 on both side matching with tabletop and balancing laminate 0.6 mm thick of approved shade as per client's choice. All edges finished with hot melt EVA glued - on polypropylene edge bands with 2 mm thick with corner and edge rounding, enabling zero sharp elements environment. Powder coated base in 75 x 25 rectangular frame. Powder coating of all the metal units must be of 60 micron 7 tank process with oven baking powder coated. The minimum factor of safety considered is 1.65 on yield stress. The allowable deflection will be limited to span/200. • Table shall have adequate arrangements for the movement of electric and LV cables seperately at desired levels with wire manager for vertical movement. Raceway having cut outs of required sizes along with 02 Nos. Hydraulic Pop Up Box/Cable Cubby with one number HDMI,Audio, LAN and 04 number 5/15 Amp. Power Ports in each. • Frame will be 14 gauge. provision for all electrical components • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make.

Discusion Table: Providing and fixing in position of customised ( factory made) Discussion table of required Size - 2100 W X 900 D X 750 H MM Table top shall be made out of 25mm thick commercial ply of BWP Grade confirming to IS 710:2010,including with 1mm thick laminate IS 2046 : 1995 on top and balancing laminate of 0.6 mm thick on bottom, of approved shade of colour as per client's choice. All edges finished with hot melt EVA glued - on polypropylene edge bands 2 mm thick with corner and edge rounding, enabling zero sharp elements environment. Powdercoated base in 75 x 25 rectangular frame. Powder coating of all the metal units must be of 60 micron 7 tank process with oven baking powder coated. The minimum factor of safety considered is 1.65 on yield stress.The allowable deflection will be limited to span/200. • Table shall have adequate provisions for the movement of electric and LV cables seperately at desired levels with wire manager for vertical movement. Raceway having cut outs of required sizes along with 02 Nos. Hydraulic Pop Up Box/Cable Cubby with one number HDMI,Audio, LAN and 03 number 5/15 Amp. Power Ports in each. • Frame will be 14 gauge. provision for all electrical components • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Conference Table: Providing and fixing in position of customised ( factory made) Discussion table of required Size - 4800 W X 1500 D X 750 H MM Table top shall be made out of 25mm thick commercial ply of BWP Grade confirming to IS 710:2010,including with 1mm thick laminate IS 2046 : 1995 on both side matching with tabletop and balancing laminate 0.6 m thick of approved shade as per client's choice. All edges finished with hot melt EVA glued - on polypropylene edge bands with 2 mm thick with corner and edge rounding, enabling zero sharp elements environment. Powdercoated base in 75 x 25 rectangular frame. Powder coating of all the metal units must be of 60 micron 7 tank process with oven baking powder coated. The minimum factor of safety considered is 1.65 on yield stress.The allowable deflection will be limited to span/200. • Table shall have adequate provisions for the movement of electric and LV cables seperately at desired levels with wire manager for vertical movement. Raceway having cut outs of required sizes along with 02 Nos. Hydraulic Pop Up Box/Cable Cubby with one number HDMI,Audio, LAN and 06 number 5/15 Amp. Power Ports in each. • Frame will be 14 gauge. provision for all electrical components • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make.

Discussion Table Round: Supplying and placing discussion table size is 1200mm (Dia) x 750mm (h). Table top shall be made in 25 mm thick commercial plywood of BWP with 1mm thick decorative laminate on the top and 0.6 mm thick balance lamination on bottom side of approved shade. Exposed edges covered with 2mm thick edge bending with using hot melt EVA glue. Table top supported metal legs with powder coated must be of 60 micron 7 tank process with oven baking powder coated. The metal legs of size 50mm x 50mm of minimum 14 gauge with 10mm high buffers offer ground clearance for easy cleaning.

Cooke Tub Four Seater Pod Set with table and seating arrangement: Supplying and Placing in place Cooke Tub four Seater with Pod Set having dimensions and specification as given below: Pod Size of each sides - 1280 W x 662 D x 1600 H MM Table Size - 900 W x 600 D x 750 H MM Table top shall be made out of 18mm thick commercial ply of BWP Grade confirming to IS 710:2010,including with 1mm thick decorative laminate IS 2046 : 1995 on both side matching with tabletop and balancing laminate 0.6 mm thick of approved shade as per client's choice. Unsuported end should be rested on 65 mm dia power coated MS pipe with suitable fixing arrangement at top and bottom. Cook Tub Specification: Size- 1200 W x 622 D x 736 H MM Structure - 25 mm foam sheets with Powder Coated 15 x 15 mm welded solid bar structure covered with layered composite of fabric Approved PU foam to have density of = 40 having premium grade with moderate resilience. Upholstered with approved fabric with more or equals to martin - dale abrasion resistance 25000 to 30000 Cycles. Color fastness to lighting - 4. Composition - Polyester - 100%. Weight not less than 360 GSM. Pod Structure - Frame should be made of medium class MS tubular section of size 50x25 mm , powder coated anchored formally at the floor level and walls at a spacing not exceeding 600 mm. The frame shall be mounted with 9 mm thick BWP ply on uphotstered sides. It should be upholstered with 25 mm foam sheets with polyester fabric on all the sides. Approved PU foam to have density of = 40 having premium grade with moderate resilience. Upholstered with approved fabric and design with more or equals to martin - dale abrasion resistance 25000 to 30000 Cycles. Color fastness to lighting - 4. Composition - Polyester - 100%. Weight not less than 360 GSM.

Cooke Tub Single Seater: Supplying and Placing in place Cooke Tub Single Seater of Dimension Size- 620 W x 622 D x 736 H MM Structure - It shall be made up of polyeurethane block of size and shape as shown in drawing and of approved quality. The block shall comprise of the base of thickness 250 mm and back tapering from 100 mm at the top to 150 mm at the top of the base. The block should be uphotstered with polyster fabric of approve make. The block shall be supported on a frame of powder Coated 32x32 mm tubular section of minimum 14 gauge as per manufacturer design. Approved PU foam to have density of = 40 having premium grade with moderate resilience. Upholstered with approved fabric with more or equals to martin - dale abrasion resistance 25000 to 30000 Cycles. Color fastness to lighting - 4. Composition - Polyester - 100%. Weight not less than 360 GSM.

Cooke Tub Three Seater: Supplying and Placing in place Cooke Tub Three Seater of Dimension Size- 1860 W x 622 D x 736 H MM Structure -It shall be made up of polyeurethane block of size and shape as shown in drawing and of approved quality. The block shall comprise of the base of thickness 250 mm and back tapering from 100 mm at the top to 150 mm at the top of the base. The block should be uphotstered with polyster fabric of approve make. The block shall be supported on a frame of powder Coated 32x32 mm tubular section of minimum 14 gauge as per manufacturer design. Approved PU foam to have density of = 40 having premium grade with moderate resilience. Upholstered with approved fabric with more or equals to martin - dale abrasion resistance 25000 to 30000 Cycles. Color fastness to lighting - 4. Composition - Polyester - 100%. Weight not less than 360 GSM.

Round Floor Table Size - Ø 900 x 330 H MM Table top made up of 25 mm thick commercial ply of BWP Grade confirming to IS 710:2010,including with 1mm thick decorative laminate IS 2046 : 1995 on both side matching with tabletop and balancing laminate 0.6 mm thick of approved shade as per client's choice. Edges finished with 2mm self glued hot pressed PVC Edge Biding with EVA glue. Base made up of metal frame, combination of Square tubes of 14 guage. Powdercoated tubular legs of dia 50 mm with buffers. Base frame will be finished of powder coating. Powder coating of all the metal units must be of 60 micron 7 tank process with oven baking coat by polyster powder coating.

Chair Bean Bag Size - 600 W x 500 D x 500 H MM Made up with Polyester fabric. Martin - Dale Abrasion resistance 25000 to 30000 Cycles Color fastness to lighting - 4 Composition - Polyester - 100% Weight not less than 360 GSM

Vinyl Bean Bag Size- 900 W x 600 D x 1200 H MM Made up with Polyester fabric. Martin - Dale Abrasion resistance 25000 to 30000 Cycles Color fastness to lighting - 4 Composition - Polyester - 100% Weight not less than 360 GSM

Large Triangular Bean Bag 1450 W x 1050 D x 1050 H MM Made up with Polyester fabric. Martin - Dale Abrasion resistance 25000 to 30000 Cycles Color fastness to lighting - 4 Composition - Polyester - 100% Weight not less than 360 GSM

Coffee Table Round Size- 600 Dia x 450 H MM Table top shall be made in 18 mm thick commercial plywood of BWP with 1mm thick decorative laminate on the top and 0.6 mm thick balance lamination on bottom side of approved shade. Exposed edges covered with 2mm thick edge bending with using hot melt EVA glue • Powdercoated base in Trirod Pattern made up of 18 mm dia MS Bar of approved shade and color with coating thickness 60 micron with proper treatment. Buffers should be provided at contact point with floor. • The minimum factor of safety considered is 1.65 on yield stress.The allowable deflection will be limited to span/200.

Centre Leg Coffee Table Round Size- 900 Dia x 450 H MM Table top shall be made in 18 mm thick commercial plywood of BWP with 1mm thick decorative laminate on the top and 0.6 mm thick balance lamination on bottom side of approved shade. Exposed edges covered with 2mm thick edge bending with using hot melt EVA glue with corner and edge rounding, enabling zero sharp elements environment. Base Slides under Couches or seats for easy movement & Space Saving. Base made up of Laser Cutted 8 mm Thick plate of 450 mm dia arc wielded with MS round pipe of medium class dia 65 mm with 50x25 tubular top frame. Frame structure shall be minimum 14 guage, frame & pipe welded together. Powder coating of all the metal units must be of 60 micron 7 tank process with oven baking powder coated.

Book Rack Storage Low Height Supplying and Placing in place Book rack of Dimension Size- 900 W x 450 D x 1240 H MM of Following specifications: • Structure made up of 18 mm BWP Ply confirming to IS 710:2010. laminated with 1 mm thick decorative laminate on visible surface and 0.6 mm balancing laminate on unvisible surface as per approved colour and shade. • Edges to be finished with 2 mm PVC edge band edging of approved make using glued with hot melt EVA glue. • Complete modular structure with minifix joinery and buffer at bottom. • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Baggage counter Size - 1200 W x 400 D x 2007 H MM • Structure made up of 18 mm BWP Ply confirming to IS 710:2010. laminated with 1 mm thick decorative laminate on visible sides and 0.6 mm balancing laminate on unvisible sides as per approved colour and shade. • Edges to be finished with 2 mm PVC edge band edging of approved make using glued with hot melt EVA glue. • Back shall be made of 12 mm BWP ply with 1 mm thick decoative laminate on visible sides and 0.6 mm thick balancing laminate on other side. • Horizontel parition shall be 12 mm and vertical parititon shall be of 18 mm BWP ply. • The complete structure shall have 18 number compartments. • Buffers shall be provided at base. • Complete modular structure with minifix joinery.

Polar Storage Size - 900 W x 450 D x 2007 H MM • Structure made up of 18 mm BWP Ply confirming to IS 710:2010. laminated with 1 mm thick decorative laminate on visible sides and 0.6 mm balancing laminate on unvisible sides as per approved colour and shade. • Edges to be finished with 2 mm PVC edge band edging of approved make using glued with hot melt EVA glue. • Back shall be made of 12 mm BWP ply with 1 mm thick decoative laminate on visible side and 0.6 mm thick balancing laminate on other side. • Horizontel parition shall be 12 mm and vertical parititon shall be of 18 mm BWP ply. • The complete structure shall have 10 number compartments. • Buffers shall be provided at base. • Complete modular structure with minifix joinery.

Open Storage Size - 900 W x 450 D x 2007 H MM • Structure made up of 18 mm BWP Ply confirming to IS 710:2010. laminated with 1 mm thick decorative laminate on visible sides and 0.6 mm balancing laminate on unvisible sides as per approved colour and shade. • Edges to be finished with 2 mm PVC edge band edging of approved make using glued with hot melt EVA glue. • Back shall be made of 12 mm BWP ply with 1 mm thick decoative laminate on visible side and 0.6 mm thick balancing laminate on other side. • The complete structure shall have 05 number compartments. • Buffers shall be provided at base. • Complete modular structure with minifix joinery.

Shutter Storage Size- 900 W x 450 D x 2007 H mm • Structure made up of 18 mm BWP Ply confirming to IS 710:2010. laminated with 1 mm thick decorative laminate on visible sides and 0.6 mm balancing laminate on unvisible sides as per approved colour and shade. • Back shall be made of 12 mm BWP ply with 1 mm thick decoative laminate on visible side and 0.6 mm thick balancing laminate on other side. • Openable shutter shall be made of 18 mm BWP ply with 1 mm thick decoative laminate on visible sides and 0.6 mm thick balancing laminate on other side with locking arrangment. SS handle of minimum 150 mm shall be provided for opening. • Edges to be finished with 2 mm PVC edge band edging of approved make using glued with hot melt EVA glue. • The complete structure shall have 05 number compartments. • Buffers shall be provided at base. • Complete modular structure with minifix joinery. • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Book Trolley: Supplying and Placing in place Book trolley with three shelves of Dimension Size- 520 W x 480 D x 1090 H MM excluding metal trolley and castor of Following specifications: • Structure made up of 18 mm BWP ply with 1 mm thick decoative laminate on visible sides and 0.6 mm thick balancing laminate on other side. The entire structure is to be mounted on duly powder coated metal frame base and back support with 04 numbers of 50 mm dia heavy duty castor wheel with brake mechanism, handles to be provided for easy movement of trolley from one place to another. • Edges to be finished with 2 mm PVC edge band edging of approved make using glued with hot melt EVA glue. • Complete modular structure with minifix joinery. • All necessary SS hardware/ fitting/ hinges/ locks/ handles etc. shall be provided of approved make

Magazine Display with tilting arrangement Size - 900W x 450D x 1830H MM Structure made up of 18 mm BWP ply with 1 mm thick decoative laminate on visible sides and 0.6 mm thick balancing laminate on other side. • Back shall be made of 12 mm BWP ply with 1 mm thick decoative laminate on all side with horizontel parition 18 mm BWP ply. • Edges to be finished with 2 mm PVC edge band edging of approved make using glued with hot melt EVA glue. • Provided with 15 openable shutters with tilting mechanism with 12 mm BWP ply laminated and edge bound as mentioned above with U profile of suitable size for holding display magzine. • Provided with buffers at base. • Complete modular structure with minifix joinery.

Newspaper Reading Table Size - 900 W x 600 D x 1350 H mm Structure made up of powdercoated metal structure with 18 mm BWP ply with 1 mm thick decoative laminate on visible sides and 0.6 mm thick balancing laminate on other side with 2 mm PVC edge band edging with hot melt EVA glue for display of news papers. Complete modular structure with minifix joinery. Provided with buffers at base.

Double Sided Shelving Size- 900 W 714 D x 2135 H MM Double Sided Open Shelving unit assembled from Post of 2100 mm H made in 2mm thick 70 x 30 mm tube punch fitted in a special reinforced having a 30 mm UNF nut on adjustable nylon level adjuster having loading capacity of 150 Kgs. Each posts to contain six flat shelves of 300 mm depth made in 1.2 mm thick CR sheet with a raised lip at the rear of each shelf and also with ‘C’ channel on front so that each shelf can be fitted perfectly in clips of the brackets of 1.8 mm thickness in CR without any screw, weld or nut features. Assembly of each shelf should be at minimum 300 mm from other. Both sides Shelves must be having height adjustment feature on clips of brackets. All the post should be manufactured in a way that it can be accommodated with Spine out display shelves. Powder coating of all the metal units must be of 60 micron 7 tank process with oven baking powder coated. The minimum factor of safety considered is 1.65 on yield stress. The allowable deflection will be limited to span/200.

Standard Slatwall Bayend Panel 714 W x 17 D x 2111 H mm The Double-Sided Bay End Panel, sized 714 W x 18 D x 2111 H mm, is made from 18 mm BWP ply with 1 mm thick decoative laminate on visible sides and 0.6 mm thick balancing laminate on other side with 2 mm PVC edge band edging with hot melt EVA glue. The panel includes two aluminum T profiles for mounting acrylic and sandwich displays (270 W x 357 L mm), with an 8 mm groove and 28 mm back, grouted along 18 mm Plywood, cut using CNC routing. The slatwall integrates 3 mm thick laser-cut acrylic for signage and book hanging, with a softening temperature of approximately 102 °C and water-insolubility. The laminate meets high durability standards: wear resistance 400 revolutions, water immersion mass increase 10% max, thickness increase 7% max, impact resistance 25N min, scratch resistance 3 N min, and color change resistance per IS: 2046-1995. It also resists steam, cigarette burns, cracking, and staining

Acrylic Holders 3 mm thick laser cut acrylic display for placing the books. Acrylic Display shall have softening temperature approx. 102 °C / 216 °F and insoluble in water.

Sleeping/Napping Pod: Supply, installation, testing and commissioning of the pod comparable to the reference image. This shall have: a. Ergonomic designed to reduce pressure on the cardiac system by elevating the feet. The seat contour should help in relaxing the muscles of the lower back by bending the knees slightly. b. Upholstery High quality synthetic leather upholstery which is super comfortable, and durable and easy to clean and maintain. c. Feature to rotate Privacy Visor to the desired position to provide semi privacy without making the person lying enclosed or claustrophobic but at the same time be easily able to block out distractions. d. An Interface Console enabling a person to Set the timer to the desired duration, or simply use the one-touch start button for a pre-programmed 20-minute nap. e. Status Indicator – The status indicator should feature red and green occupancy lights. The lights should also communicate time remaining during use, making it easy for users to see when the Pod is available, and if currently occupied, when it will next be free. f. Usage Tracking feature – The system should record usage data, which can be translated into individual device reports. Usage across devices can then be compared for effectiveness, producing valuable information for facility management. g. Understructure and Exterior: understructure shall be sturdy and exterior should be appropriate material and aesthetically sound.

Circulation Counter Size - 2400 W x 750 D x 1050 H MM Complete Structure in commercial plywood 16 mm thk. finished with 1 mm Laminate on table top & sides, & inner structure to be in 0.8 mm laminate of approved shade as per client's chopice. All edges finished with glued - on polypropylene edge bands with corner and edge rounding, enabling zero sharp elements environment. Provided with fixed padestal at base , which have 3 drawers on drawer channel & C type handle. Hardware - Ebco, Hettich or other relevant. Ply - Grassim,Archid or relevant. Laminate - Greenlam, Century or other relevant

Curved Bookcase with Seating With Back Size - 1372 W x 1000 D x 900 H mm ( seat height : 450 H) Bookcase made up of 17 mm prelaminated MDF finished with 2 mm PVC edge band. Provided with acrylic at back for stability Soft seating made up of Metal Under structure covered with plywood. Further Covered with non water absorbent, High Density Foam of density = 40, Martin - Dale Abrasion resistance = 20000 Cycles, Color fastness to lighting - 4, Composition - Polyester - 100%, Weight - 360 GSM Botton Fit 50X25 mm nylon glides below it.

Mobile Newspaper Display 824 W x 824 D x 1500 H mm Product made up of 17 mm prelaminated MDF finished with 2 mm PVC edge band. Display at all 4 sides for Newspaper in Acrylic holder