Housing And Urban Development Authority Tender
Bidassist allows us to explore new opportunities across the whole world so as to support the growth of the business. It is designed in such a manner that if we need any kind of information about any government e-tender the Himachal Pradesh government has posted on its website, Bidassist provides the same in a very hassle-free manner. As BidAssist is designed as a very user-friendly website which helps us find the specific Himachal Pradesh etender we are looking for.
Housing And Urban Development Authority - HIMUDA Tender
Eprocure
Opening Date22 Jan 2021
Closing Date10 Feb 2021
Tender AmountRefer Documents
Costs
EMD
₹ 1,50,560Document Cost
₹ 5,900Tender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2021_HIMUD_43743_1Bid Award Id
ViewTender No
Smart City Mission Shimla SH Remodeling RenovatiTender Authority
Housing And Urban Development Authority ViewPurchaser Address
-Website
http://http://himuda.hp.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
Smart City Mission Shimla SH Remodeling Renovation of Residential Block No 5 single Room ACC 3 unit 12 Nos flats without parking Old Abkari Building at Krishna Nagar Shimla 171001 including internal WS SI EI and Development of site in LGSF Pre Fab t
BOQ Items
Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuttering,strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work including carriage of material in all leads & lifts. a) Foundation, footings basis of columns etc. and mass concrete.
17.76
-
-
b) Flat surfaces such as soffits of suspended floors, roofs, landings and the like.Floors etc.upto any thickness.
41.78
-
-
c) Columns,pillars, posts and struts. Square, rectangular or polygonal in plan.
202.5
-
-
d) Stair cases with sloping or stepped soffits excluding landing.
71.89
-
-
e) Beams,cantilevers,girders and lintels, Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding1mtr. In depth in all heights from floor.
168.53
-
-
f) Edges of slabs and breaks in floors and walls: For any width.
11.5
-
-
Providing and laying cement concrete 1:4:8 (1cement:4sand: 8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work including carriage of material in all leads & lifts. a) Foundation and plinth.
7.2
-
-
Providing and laying cement concrete 1:6:12 (1cement:6 sand :12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of centring and shuttering including carriage of materials in leads & lifts. a) Foundation and plinth.
38.99
-
-
Providing and laying cement concrete 1 : 8 : 16 (1cement : 8 sand :16 graded stone aggregate 20 mm nominal size) and curing complete on slab and floor, under floor/ depressed slab excluding cost of form work including carriage of materials in all leads & lifts.
5.54
-
-
Applying cement slurry on R.C.C. slab or cement concrete work using 2.75 kg of cement per sqm. of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete including carriage of materials in all leads and lifts.
280.89
-
-
Providing and laying cement concrete having strength of M-20 Design mixed aggregate and curing complete excluding cost of form work and reinforcement for reinforced concrete work including carriage of materials in all leads & lifts. a) Foundations, footings, bases of columns and the like and mass concrete including carriage of materials in all leads and lifts.
11.99
-
-
b)Suspended floors, roofs, landings and shelves and their supports, balconies beams, girders, bressumers and cantilevers upto all floor level.
33.56
-
-
c) Columns,pillars,posts and struts. Square, rectangular or polygonal in plan.
18.23
-
-
d) Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto all heights.
6.81
-
-
Providing Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire upto all floor levels including carriage of materials in all leads and lifts.
8470.8
-
-
Providing throating or plaster drip and moulding to R.C.C. chajja including carriage of materials in all leads and lifts.
266.4
-
-
Providing and mixing polyester triangular synthetic fibres in specified ration 6-18mm length designed for melting point 240-260 degree centigrade and having specific gravity of 1.33-140 as per IS-456 amendment August 2007 & IRC 44- 2008 @ 125 grams/50kg of cement bag in plastering work including carriage of materials in all leads and lifts.
49
-
-
Brick work using 2nd class common burnt clay building bricks in superstructure in cement mortar 1:6 (1 cement : 6 sand) including carriage of materials in all leads and lifts.
2.95
-
-
Half brick masonry using 2nd class common burnt clay building bricks in superstructure above plinth level upto all heights in cement mortar 1:4 (1 cement: 4 sand) including carriage of materials in all leads and lifts.
17.28
-
-
Stone soiling properly hand packed filling interstices with spalls and consolidating with hand ramming to the required gradient and camber including spreading, watering and rolling of binding materials moorum or earth etc. complete as per HP.PWD specification. 100 mm spread thickness (finished work including materials and labour including carriage of materials in all leads and lifts.
12.25
-
-
Random rubble masonry/polygonal rubble masonry (Uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth up to all depths & heights including super-structure if required including levelling up with cement concrete 1:6:12 (1 cement : 6 Sand : 12 graded stone aggregate 20mm nominal size) in cement mortar 1:6 (1 cement:6 sand) in breast walls and retaining walls including carriage of materials in all leads & lifts.
281.14
-
-
Stone filling behind retaining walls including carriage of materials in all leads and lifts.
125.86
-
-
Providing and fixing PVC pipe 100mm diametre for weep hole in retaining walls/breast walls including carriage of materials in all leads and lifts.
145
-
-
P/F partical board ceiling of approved quality with butt jointing and nails (frame work and cover fillets to be paid for separately including carriage of materials in all leads and lifts. i) 12mm cement bonded partical board.
1786.24
-
-
P/F partical board ceiling of approved quality with butt jointing and nails (frame work and cover fillets to be paid for separately including carriage of materials in all leads and lifts. i) 8mm cement bonded partical board.
1963.03
-
-
Providing and fixing thermal insulation with Resin Bonded rock wool conforming to IS:8183, having density 48kg/m3, 50mm thick, fixed to wall with screws, rawl plugs & washers and hold in position by criss cossing GI wire etc. complete as per directions of Engineer-in-Charge including carriage of materials in all leads and lifts.
981.53
-
-
Providing and fixing gypsum board ceiling of approved quality with butt jointing and steel screws (frame work and cover fillets to be measured and paid for separately) including carriage of materials in all leads and lifts. i) 6mm thick
379.63
-
-
Providing and fixing factory made PVC door frame double rebate of required colour & shade of size 50mmx95mm with a wall thickness of 5mm made by jointing 3 Nos heat bent PVC sheet C chanel of 5mm PVC foam sheet of sizes 35x30x25mm and 40x35x40mm & 25mmx30mmx35mm for jointing using solvent cement. the two side C channels shall be reinforced with 19mmx19mm M.S. square tube of 19 gauge and all the three "C" channels shall be fixed to flat base of 5mm thick PVC sheet with salvent cement. the profile shall be mitred at corners and joined by inserting 4 nos 150mm long bracket of 15mmx15mm M.S. square tube to inner side. the 19mmx19mm M.S. square tubes the door frame shall be fixed to wall with 100mm long M.S. screws to wooden or rawl plugs embedded in masonry complete including carriage of materials in all leads and lifts as per the specification of manufactures & direction of Engineer -in-charge.
543
-
-
Providing and fixing factory made PVC door frame single rebate of any colours of size 50x47mm with a wall thickness of 5mm made out of extruded 5mm rigid PVC foam sheet heat bend & mitred at corners and jointed with 2 Nos. of 150mm long brackets of 15mmx15mm M.S. square tube, the vertical door profiles to be reinforced with 19mmx19mm M.S. square tube of 19 gauge EPDM rubber gasket weather seal to be provided throughout the frame i/c fixing of door frame to wall with M.S. screws 100long with wooden or rawl plugs emedded in masonry complete including carriage of materials in all leads and lifts as per manufactures specification & direction of Engineer-in-Charge.
182.4
-
-
Providing and fixing to existing door frames, 30mm thick factory made PVC panelled door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x19mm for styles and 15mmx15mm for top & bottom nails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC "C" channel of size 30mm thickness, 70mm width cut of which 50mm shall be flat and 20mm shall be tappred in 45 degree angle on either side forming style and 5mm thick, 95mm wide, PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm thick, 20mm wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails,oints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm size with necessary screws etc complete.
85.68
-
-
Providing and fixing to existing window frames, 30mm thick factory made PVC glazed window shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x19mm for styles and 15mmx15mm for top & bottom nails, M.S. frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC "C" channel of size 30mm thickness, 70mm width cut of which 50mm shall be flat and 20mm shall be tappred in 45 degree angle on either side forming style and 5mm thick, 95mm wide, PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both side to form lock rail, top, bottom and lock rail shall be provided either side of the panel 10mm thick, 20mm wide cross PVC sheet be provided as gap insert for top rail and bottom rail paneling of 5mm thick both side PVC Sheet to be fitted in the M.S. frame welded/sealed to the style & rails,oints mitred and jointed with solvent cement adhesive i/c fixing of PVC shutter with existing frame with M.S. butt hinges 100x50x1.90mm size with necessary screws etc complete.
114.73
-
-
Supplying & fixing glass panes 4 mm thick in PVC window including beading of required size. including carriage of material in all leads & lifts.
57.36
-
-
Providing and fixing aluminium anodised powder coated pattern (grill) to existing window/ventilatior with 80mmx80mm panels holes with 25x8mm thick aluminium flat in windows and ventilators including fixing with aluminium screws or bolts and nuts complete in alluminium channels base frames (Aluminium channels base frames to be measured and paid for separately).
118.62
-
-
Providing and fixing to existing door frames 30mm thick factory made wire mesh solid PVC door shutters consisting of frame made out of M.S. tube of 19 gauge thickness of size 19mmx19mm for style and 15mmx15mm M.S. square tube for top, bottom & Lock rail M.S. frame shall have a coat of steel primer and covered with 5mm thick PVC solid sheet heat moulded "C" channel of size 75mmx30mmx60mm out of which 10mm shall be bent at 90degree towards inner side on front face of the door M.S. frame at lock rail shall be covered with 100mm wide PVC sheet out of which 10mm on both the edges shall be bent at 90 degree on front face of the door and 85mm wide PVC sheet shall cover the M.S. frame at top, bottom & lock rail lof 70mm on back side of door 5mm thick 20mm wide cross PVC sheet as gap insert for top and bottom rail, PVC sheet beading of 10mm thick, 15mm wide PVC sheet beading in to be stick internally in the back side of style and rails of door with solvent cement adhesive i/c fixing of G.I. wire mesh 85G or 0.56 dia wire fixed between PVC sheet of style and rail bent at 90 degree on front face using 15mmx15mm L-shape PVC beading nailed on style a rails i/c fixing shutter to existing door frame with M.S. butt hinges 100x58x1.90mm with necessary screws etc. complete including carriage of materials in all leads and lifts.
104.77
-
-
Providing and fixing anodized aluminium sliding door bolt anodized transparent or dyed to required colour and shade with bolts and nuts, screws etc.complete including carriage of materials in all leads and lifts.
-
-
-
i) 250x 16 mm
36
-
-
ii) 300x 16 mm
12
-
-
Providing and fixing aluminium tower bolt (barrel type) anodized to transparent or dyed to required shade and colour with screws etc. complete including carriage of material in all leads and lifts.
-
-
-
250x 10 mm
24
-
-
150 x 10 mm
72
-
-
100 x 10 mm
144
-
-
Providing and fixing aluminium handles anodized transparent or dyed to required colour or shade with necessary screws including carriage of materials in all leads and lifts.
-
-
-
i) 125mm .
24
-
-
ii) 100mm .
96
-
-
Providing and fixing bright finished hard drawn hooks and eyes 150 mm including carriage of materials in all leads & lifts.
108
-
-
Providing and fixing 100mm aluminium floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of materials in all leads and lifts
48
-
-
Providing and fixing 19mm thick Commercial Board water proof shutters for cup boards i/c fixing with nickel plated piano hinges with screws etc complete including carriage of materials in all leads and lifts.
45.36
-
-
Providing and fixing 19mm thick water proof commercial board in shelves/box for cup board with butt joints & fixing with nails & screws etc complete including carriage of materials in all leads and lifts.
120.72
-
-
Providing and fixing 1.00mm thick coloured or plain lamination sheet (sunmica) on boards/ply wood sheets with approved adhesive and nails etc complete including carriage of materials in all leads and lifts.
45.36
-
-
Providing and fixing square edge cover fillets (beading) 19mmx6mm section i/c mitring at junctions with wood screws and nails complete including carriage of materials in all leads and lifts.
153.6
-
-
Providing and fixing bright finished brass ball catcher 10 mm dia including carriage of materials in all leads and lifts.
24
-
-
Providing and fixing 65x35mm special quality chromium plated brass cup board lock with six leavers including necessary screws etc. complete (Indian make) including carriage of materials in all leads and lifts
12
-
-
Providing and fixing bright finished brass handles with screws etc. complete including carriage of materials in all leads and lifts. 75mm
24
-
-
Providing and laying granite stone in flooring 20mm(average) thickness base of cement mortar 1:3(1cement: 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone rubbing and polishing including cost of rounding of edges etc. complete including carriage of materials in all leads and lifts. 20mm.thick
35.4
-
-
Providing and laying Duro stone vetrified tiles (600x600mmx10mm) any colour/design/shade as approved by Engineer in charge of in flooring, treads of steps and landing and single piece on steps of stair case laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.including cost of cutting tiles wherever requireds including carriage of materials in all leads and lifts.
180.72
-
-
Providing and laying Duro stone vetrified tiles (600x600mmx8mm) any colour/design/shade as approved by Engineer in charge in skirting, single piece on risers of steps and dado on 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete including cost of cutting tiles wherever requireds including carriage of materials in all leads and lifts.
55.02
-
-
Providing and laying 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles any colour/design/shade as approved by Engineer in charge in flooring, treads of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required i/c cost of cutting tiles wherever required complete including carriage of materials in all leads & lifts.
144.54
-
-
Providing & fixing digital tiles 6mm thick of any colour/design/shade as approved by Engineer in charge where ever required in skirting, risers of steps and dado on 12mm thick cement mortar 1:3 (1cement:3 sand) & jointed with cement slurry i/c cost of cuttings tiles wherever required i/c carriage of materials in all leads and lifts.
360.36
-
-
Providing and fixing 15 cm. wide 45 cm. overall semicircular plain Prepainted sheet sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary connections with rain water pipe complete as per design i/c carriage of materials in all leads and lifts.0.80mm thick sheet
45.58
-
-
Supply & Fixing of COLORBOND LYSAGHT TRIMDEK profile sheet of 1072 mm Supply width and nominal 28.5 mm deep ribs in roofing.The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness (BMT), Hi-Tensile steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminum-Zinc alloy (55% Aluminum, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides) with Super Polyester Colorbond XRW quality paint coat as per AS/NZS 2728 Class 3 of BlueScope Steel make. The paint will have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior coat on top surface and nominal 5 μm reverse coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade by concern authority. The sheet shall have brand marking of the manufacturer giving product details on the back of the sheet at every regular interval for confirming genuinity of the material In roofing.including all leads, lifts and carriage of materials and as per entire satisfaction of the Engineer-in charge . Any loss of Govt. and private property during the execution of work the absulte responsibilty of the contractor i/c carriage of materials in all leads and lifts.
198.04
-
-
Providing and fixing ridges or hips 60 cm overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the
direction of Engineer in Charges i/c carriage of materials in all leads and lifts.
38.79
-
-
Providing and fixing flushing 38cm overall with 0.60mm thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories as required as perthe direction of Engineer-in-Charge including carriage of materials in all lead and lift.
16.57
-
-
Providing & fixing Valley 60cm overall with 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP ) organic coating of 20 micron over 5 micron primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm diameter with prepainted G.I. limpet & bitumen washer complete with all accessories as required as per the direction of Engineer - in - charge including carriage of materials in all leads & lifts.
20.4
-
-
Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete.150mm dia pipes all leads and lifts ,Including carriage of all labour equipment and material to various locations through all modes of transportation in all leads and lifts, including all incidental charges and complete as per entire satisfaction of the enginer in charge i/c carriage of materials in all leads and lifts. Rain Water Pipes
132
-
-
Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete PVC Plain bend 150mm dia including carriage of materials in all lead and lift.
20
-
-
PVC shoe 100mm dia
10
-
-
Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawl plugs etc. complete. 150 mm dia, including carriage of all labour equipment and materials to various locations through all modes of transportation in all leads and lifts, including all incidental charges and complete as per entire satisfaction of the Enginer in charge.
70
-
-
Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely)including carriage of materials in all leads and lifts.
42.5
-
-
Steel work welded in built up sections, trusses and framed work, including cutting,hoisting, fixing in position and applying a priming coat of red lead paint including carriage of materials in all leads and lifts: -
-
-
-
a) In beams joists channels ,angles ,tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.
37
-
-
b) In gratings, framed guard bars, ladders, railling, brackets and similar works i/c making holes & filling the same with cement concrete 1:2:4 (1 cement:2 sand :4 graded stone aggregate 20mm nominal size).
120.01
-
-
Design, preparation of drawings, supply and erection in position of TRUSSS® Roof truss solution (top and bottom cord, Top batten and ceiling batten) manufactured from zinc-aluminium alloy coated steel- ZINCALUME steel(minimum yield strength of 550 MPa, coated with anAZ150 (min 150 gm/m2 total on both side complying to AS1397) base metal thickness of 0.75/1.0 mm and shall be C – type having web 75 X 40 mm or 100 X 50 mm with lip size of 8.00 / 12.0 mm & R 5.0 mm, whichever is economical as per AS1397/NZM design calculation and shall have a spacing @1200 c/c.The truss shall be design through appropriate software complying to design code of AS 1170 -2- 1998 /AS 4600-1996 and most economical design. Self tapping / drilling fasteners shall be min. 40 μm Zinc coated / min. 25 μm Zinc-Tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners. The truss purlin members should be manufactured from ZINCALUME or equivlant (min. 150 gsm & 550 MPA ) steel of base metal thickness 0.75/1.0 mm and shall be top hat TS41 (41 X 32) or TS61 (61 X 36.5).Design of Cold formed sections to be done by SUPRACADD or equivalent Design software of relevant AS/NZM codes (4600,1170).
3979.1
-
-
Providing and fixing Decking Sheet 0.80 mm to1.0 mm thick for floor slab to fixed with screws, rawl plugs & washers including carriage of materials in all leads and lifts.
303.62
-
-
Providing & fixing stainless steel railing in staircase incuding fixing in position complete as per design approved by Engineer-in-Charge i/c carriage of materials in all leads and lifts.
123.48
-
-
Providing & fixing stainless steel 3" dia vertical post in staircase i/c carriage of materials in all leads and lifts.
80
-
-
Painting two coats (excluding priming coat on new steel and other metal surfaces with enamel paint brushing, to give an even shade including cleaning the surface of all dirt,dust and other foregin matters. Enamel paint other than white/white paint including carriage of materials in all leads and lifts.
441.63
-
-
Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of material in all lead and lift.
2492.53
-
-
Distempering (two coats) with oil bound washable distemper of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade over and including a priming coat with Alkali-resistance primer of approved brand and manufacture after thoroughly brushing the surface free from mortar dropping and other foreign matter and also including preparing the surface even and sand papered smooth including carriage of materials in all leads and lifts.
-
-
-
(a) On Wall.
1918.26
-
-
(b) On Ceiling.
379.63
-
-
Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand papered smooth complete including carriage of materials in all leads and lifts.
574.27
-
-
6mm cement plaster to ceiling or slopping surface in cement mortar 1:3 (1cement :3sand) including carriage of materials in all leads & lifts.
103.71
-
-
15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth.Cement Mortar 1:6 (1 cement:6 sand) including carriage of materials in all leads and lifts.
212.88
-
-
20mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth.Cement Mortar 1:6 (1 cement:6 sand).including carriage of materials in all lead and lifts.
212.88
-
-
Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1cement :3 sand :6 graded stone aggregate 20 mm nominal size) including finishing the top surface of concrete smooth complete including carriage of materials in all leads and lifts.
31
-
-
Providing under layer for plinth protection of 75 mm thick ( unconsolidated) bed of dry bricks/stone aggregate 40 mm nominal size well rammed and consolidated and grouted with fine sand including preparation of ground including carriage of materials in all leads and lifts.
31
-
-
Brick edging brick laid on edge to plinth protection with bricks including grouting with cement mortar 1:4 (1 cement: 4 sand) (I) with bricks size 19 cm x 9 cm x 9 cm including carriage of materials in all leads and lifts.
53.78
-
-
Constructing course rubble hammer dressed "U" shape open surface drain with side wall 15x22 cm in cement mortar 1:6(1 cement:6 sand) and in side plastering with cement mortar 1:3(1cement : 3sand) including earth work and laying 10 cm.cement concrete in 1:5:10(1 cement :5sand:10 graded stone aggregate 40 mm.nominal size) and 7.5 cm cement concrete 1:2:4(1 cement :2 sand:4 graded stone aggregate 20mm. nominal size ) and finished with a floating coat of neat cement complete as per standard design. including carriage of materials in all leads and lifts.
53.78
-
-
Demolition above G.L. upto all floor level and disposal of unserviceable materials within all leads & lifts. (a) Un-reinforecd cement concrete upto 15 cm. Thickness.
39.24
-
-
Demolition above G.L.upto all floor level including disposal of unserviceable materials within all leads and lifts including cutting the necessary reinforcement and separating out from R.C.C. /R.B. works (a) R.C.C.work
2.89
-
-
Demolition of brick work above ground level upto all floor level including stacking of serviceable materials within all leads and lifts. (a) In Cement Mortar.
25.03
-
-
Demolition of stone masonry above G.L upto all floor level including stacking of serviceable materials and disposal of un-serviceable materials within all leads and lifts (a) Rubble masonry in cement mortar.
336.34
-
-
Dismantling tiled floors laid in mortar upto all floor level including stacking of serviceable material and disposal of unserviceable materials within all leads and lifts (wooden/concrete joists to be measured and paid for separately. (a) For thickness of tiles upto any thickness.
17.15
-
-
Dismantling roofing including ridges, hips, valleys, gutters etc. stacking the serviceable materials and disposal of un-serviceable materials within all leads and lifts. (a) G.I. Sheet roofing
370.26
-
-
Dismantling ballies in posts, purlins or rafters including stacking the materials within all leads and lifts.
548.8
-
-
Dismantling doors, windows and clerestory windows,ventilators etc. (wood or steel) shutters including chowkhats, architraves, hold fasts and other attachements etc. complete and stacking them within all leads & lifts, Not exceeding 3.0 Sqm. in area
30
-
-
Providing and fixing Polytheline – Aluminium - Polyethylene (PE-AL-PE) composite pressure pipe U.V. stabilized with carbon black confirming to IS-15450-2004 water supply including clamp at one metre spacing, cutting , fixing and making good the wall etc. but excluding the cost of fittings (internal work) pipes exposed on wall including carriage of material in all leads and lifts. (a) Internal work Exposed on wall.1216 (16 mm OD pipe).
796.2
-
-
Providing and fixing composite end seal compression fittings as per IS-15450-2004 for hot/cold water supply e.g elbow,tees , reducers , couplers & connectors etc. with includes testing of joints complete as per direction of Engineer-in-charge including carriage of material in all leads and lifts.
-
-
-
(a) Equal Tees (i) 1216
96
-
-
(b) Reducing Tees (i) 1216 x all branches
48
-
-
(c) Female Branch Tees (i) 1216 x 1216 x 15 mm thread
72
-
-
(d) Female Elbows(i) 1216 x 15 mm thread
120
-
-
(e) Male thread connector(i) 1216 x 15 mm thread
48
-
-
(f) Female thread connector(i) 1216 x 15 mm thread
48
-
-
(g) Couplers(i) 1216
24
-
-
(h) Reducers(i) 1620 x 1216
12
-
-
Providing and laying in trenches in all depth galvanised mild steel tubes (medium grade) including tube fittings (earth work in trenches to be measured and paid separately) including carriage of material in all leads and lifts. (a) 25 mm dia
17.98
-
-
Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipes complete.including carriage of material in all leads and lifts
12
-
-
Providing and fixing plastic seat (Solid ) and cover for wash down water closet with C.P. Brass hinges and rubber buffers including carriage of material in all leads and lifts. white/Coloured plastic seat and cover
12
-
-
Providing & Fixing PTMT Coloured/white high density polyethene/poly propylene 10 liters capacity (full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve,syphon,15mm nominal size PVC ball valve with polythene float ,with push button,couplings for constructions with inlet,outlet and over flow pipe,40mm dia C.P. flush bend including cutting holes in walls and making good the same and connectio the flush bend with cistern and closet (over flow pipe to be measured and paid for separately) including carriage of material in all leads and lifts.
12
-
-
Providing and fixing vitreous China wash basin with single/double hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings including carriage of material in all leads and lifts. (a) Flat back 550mmx400mm
12
-
-
Providing and fixing Vitreous China pedestal for wash basin complete recessed at the back for the reception of pipes and fittings including carriage of material in all lead and lifts.
12
-
-
Providing and fixing C.P Brass waste for wash basin or sink including carriage of material in all leads and lifts. (a) 32mm dia
12
-
-
Providing and fixing vitreous china wash down water closet (European type W.C. pan) with integral ‘P’ or ‘S’ trap including jointing the trap with soil pipe in cement mortar 1:1(1cement:1sand) (Seat and cover to be measured and paid for separately) Anglo Indian Universal Closet, including carriage of material in all leads and lifts.
12
-
-
Providing and fixing brass full way valve with wheel including carriage of material in all leads and lifts. (a) 15mm nominal size
12
-
-
Providing and fixing G.I./M.I. unions of following sizes(where not included in the item) 15mm including carriage of material in all leads and lifts
36
-
-
(a) 25mm dia.
2
-
-
(b)32mm dia.
1
-
-
Providing and fixing PVC waste pipe for wash basin or sink including carriage of material in all lead and lifts. (a)32mm dia
12
-
-
(b) 40mm dia
12
-
-
Providing and fixing 600mm x 450 mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers including carriage of material in all leads and lifts.
12
-
-
Providing and fixing C.P. brass towel rail complete with C.P brass brackets fixed to rawl plug with C.P brass screw including carriage of material in all leads and lifts. (a) 600X20mm
12
-
-
Providing and fixing 600mm x 120 mm glass shelf with C.P. Brass bracket and guard rail complete, fixed to wooden plugs with C.P. Brass screws including carriage of material in all leads and lifts.
12
-
-
Providing and fixing C.P. brass soap dish with C.P. brass brackets fixed to wooden cleats with C.P. brass screws confirming to BIS specification including carriage of material in all leads and lifts.
12
-
-
Providing and fixing C.P. Brass shower rose with 15mm or 20mm inlet including carriage of material in all lead and lifts. (a) 100mm dia
12
-
-
Providing and fixing C.P. brass bib tap with capastan head including carriage of material in all leads and lifts :- (a) 15mm dia.
36
-
-
Providing and fixing Brass stop cocks including carriage of material in all leads and lifts. (a) 15mm dia
24
-
-
(b) 25 mm dia
2
-
-
(c) 32 mm dia
1
-
-
Providing and fixing C.P. brass angle valve 15mm with or without Nuts and pipe including carriage of material in all leads and lifts.
48
-
-
Providing and fixing C.P. Brass concealed stop cock 15mm dia including carriage of material in all leads and lifts.
24
-
-
Providing and fixing Mixer for kitchen sink with casted swinging spout at top including carriage of material in all lead and lifts.
12
-
-
Providing and fixing one hole basin mixing Faucet. including carriage of material in all lead and lifts.
12
-
-
Providing and fixing P.V.C connection with brass unions including carriage of material in all leads and lifts..Confirming to BIS Specification. (a) 300/450mm length 15mm dia
60
-
-
Providing and fixing PVC water storage tank sintex make ISI marked, G.I. inlet and outlet connection, 15mm nominal bore bal l valve and mosquito proof PVC cover with locking arrangement including hoisting up to all heights above ground level including carriage of material in all leads and lifts. (a)1000 litres net capacity tank.
12
-
-
Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the walls and floors etc complete. (a) 110mm x 75mm including carriage of material in all leads and lifts.
36
-
-
Providing and fixing high pressure PVC spigot and socket soil waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts:- (a) 75mm dia.
58.8
-
-
(b) 110mm dia
54
-
-
(c) 150mm dia
38.8
-
-
Providing and fixting PVC single equal branch with oval access door, ISI marked insertion rubber washers 3mm thick bolts and nuts including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts:-(a)75mm dia.
6
-
-
(b) 110mmdia
6
-
-
Providing and fixting PVC door bend with oval access door, ISI marked insertion rubber washers 3mm thick bolts and nuts including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts:-(a) 75mm dia.
6
-
-
(b)110mm dia
6
-
-
(c) 150mm dia
1
-
-
Providing and fixting PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.(a)110mm dia.
16
-
-
(b) 75mm dia.
16
-
-
Providing and fixting PVC plain bend ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts (a) 75mm dia.
9
-
-
(b) 110mm dia.
9
-
-
(c) 150mm dia.
1
-
-
Providing and fixting PVC clamp ISI marked of approved design with steel screws and rawal plugs etc. complete including carriage of material in all leads and lifts (a) 75mm dia.
24
-
-
(b) 110mm dia
24
-
-
Providing and fixing PTMT JET spray of approved quality and colour with one meter tube. including carriage of material in all leads and lifts.
12
-
-
Providing and fixing stainless steel kitchen sink of approved standard with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting.(a) 610 x 510 mm with bowl depth 200 mm including carriage of material in all leads and lifts.
12
-
-
Providing and fixing 100 mm dia chromium plated grating of superior quality for floor, gully or nahani trap including carriage of material in all leads and lifts.
36
-
-
Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 and water tight C. I. cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53kg and frame to be not less than 2.72kg including carriage of material in all leads and lifts. (a) Square Mouth Traps100mmX100mm size P type
3
-
-
Constructing man hole with RCC top slab in 1 : 2 : 4 mix (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 (1 cement : 4 sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 15 mm thick with cement mortar 1:3 ( 1 cement : 3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1 : 2 : 4 mix (1cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) finished smooth complete including curing and testing. (a) Inside size 800x800mm and 500mm deep with steel fibre reinforced concrete manhole cover and frame (medium duty) 560mm internal dimension total weight of cover and frame to be not less than 173 Kg.(weight of cover 70 Kg. and weight of frame 103 kg With 230 mm thick walls of brick masonry using 2nd class common burnt clay building bricks in cement mortar 1:3 (1cement:3sand).including carriage of material in all leads & lfits.
4
-
-
Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with modular switch modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.Group B.
144
-
-
Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.
48
-
-
Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.
360
-
-
Wiring for power plug with 4x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.
240
-
-
Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.
-
-
-
(a) 2x1.5 Sq. mm.
180
-
-
(b) 2x6.0 Sq. mm.
210
-
-
Supplying and drawing LAN cable CAT 5E, solid copper conductor protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required.
120
-
-
Supplying and fixing of following sizes of PVC conduit along with the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required:-(a) 20 mm. dia
96
-
-
Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required. (a) 2 modules (78mmx78mmx50mm)
12
-
-
Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required. (a) TV. Socket outlet, modular.
12
-
-
Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required.
96
-
-
Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required.
60
-
-
SSupplying and fixing Ding-Dong / Electronic musical bell, suitable for .C./A.C. single phase,230 volts complete as required:-
12
-
-
Supplying and erection of following depth sheet metal cubical pedestal of suitable dimensions with plus-minus 5 cm variation, made from 1.6 mm thick M.S. sheet duly fabricated in a segregated manner for housing of switch fuse units, by welding each compartment on five sides & front side hinged, complete with locking arrangement, with sufficient No. vertical and horizontal intermediate switchgear housing compartments. The cubical pedestal shall have cable entry box at one or two sides, with epoxy powder coated approved paint and bonding to the existing earth etc. The same shall be erected in the 1:2:4 cement concrete plat-form of suitable dimensions 15 cm high from ground level and 45 cm thick. The cubical pedestal shall be 15 cm from the top of cement concrete plat-form 300 mm deep (nominal)
3
-
-
Supplying and fixing copper strip bus-bars suitable for 100 Amp. 415 volts apacity 4 No. each of cross-sectional area (25.4mmx3.17mm),in the existing enclosure with all accessories including connections etc. as required:-
1.2
-
-
Providing and fixing following rating and breaking capacity MCCB in the existing cubical panel board including drilling holes in the cubicle panel, making onnections, etc. as required. (a)100 Amp. -10 KA
1
-
-
Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required. (a) Single pole. Cat-A.
84
-
-
Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) 40 Amps. Cat-A.
12
-
-
Supplying and fixing following rating, double pole (single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 miliampers in the existing MCB DB complete with connections, testing and commissioning etc. as required. (a) 40 Amps. Cat-A.
12
-
-
Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required. (a) Double door-12 way
12
-
-
Earthing with G.I earth pipe 4.5 mtr. long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.
2
-
-
Extra for using salt and charcoal for pipe earth electrode complete as required.
2
-
-
Providing and fixing 6 SWG (4 mm dia.) G.I. wire on surface or in recess for loop earthing as required.
70
-
-
Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade direct in ground; to be laid 1 meter below the ground level including excavation and refilling the trench etc.as required, but excluding sand cushioning and protective covering:- i) Armoured cable 25 sq. mm (3.5 cor
40
-
-
ii)Armoured cable 70 sq. mm (3.5 core)
40
-
-
Providing, laying and fixing of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade on surface etc. of the required size:-core) i) Armoured cable 25 sq. mm (3.5 core)
40
-
-
ii) Armoured cable 70 sq. mm (3.5 core)
40
-
-
Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Nonreturn valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections,safety valve connections,testing and commissioning etc.as required:- i) 25 Litres capacity water heater (Cat-A)
12
-
-
Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required:- i)Ceiling Fan 1200 mm sweep,Category-A
12
-
-
Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required:- i)Exhaust Fan, Light duty, (Domestic) 300 mm sweep
24
-
-
Providing and fixing LED tube 20 watt of Extuded Aluminium Led Batten product code BCLBAL 20 W cool white of bajaj or equivalent make as required and approved by the Enginner-in-Charge.
24
-
-
Providing and fixing wall Bracket Floretine WL 1LS B22 SS of 9 watt Led Lamp B22 base of Havells or equivalent make as required and approved by the ngineer-in -charge.
36
-
-
Providing and fixing Bulk Head Luminaire of IP 65 product code BIBWP 10 w LED of bajaj or equivalent make as required and approved by the Enginner-in-Charge.
12
-
-
Supplying and fixing of concealed fan box with suitable size of phenolic laminated sheet cover in the front complete in all respect as required and approved by the engineer-in-charge.
12
-
-
Providing and fixing Surface Led celling panel with Al die castbody with optimized heat sink product code BGSLA Sleek surface 6W WH RD of bajaj or equivalent make as required and approved by the Engineer -in -charge
12
-
-
Providing and fixing Mirror Light of 300 mm Product code LCL 07-CDL of Crompton or equivalent make as required and approved by the Engineer-in -charge.
12
-
-
Providing and fixing instant Geyser with product Code GHWEOBPWH003 of capacity 3 ltr. /3 KW Havells or its equivalent make as required and approved by the Engineer-in -charge.
12
-
-
Providing and fixing of DWC pipe of size OD 90 and ID 76 of polyplast and equivalent make etc. as required and approved by Engineer-in -charge.
40
-
-
Supplying and laying of DWC pipe of size OD 40and ID 32 of polyplast and equivalent make as required and approved by Engineer-in-charge.
40
-
-
Note:-Minimum cost of useable materials recovered after dismantling of existing old structure i.e, Rs.360471/- only will be effected and said cost will be recoverable from the Contractor /Firm /Company. (-)
-
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements