Himachal Pradesh Tourism Development Corporation Tender

Image for design reference only Providing & supplying round low table finished with Veneer 1300 x 400(DXHt) with a Walnut veneered top in cross cut pattern finished.The top edge to be 75mm thk with rounded edge made of 18mm double BWP ply (Greenply/Century or equivalent) top including carriage of materials within all leads and lifts. The legs to be in Teak wood without knots , and joined to the circular frame and to have the same profile as shown in the image Veneer to be finished with PU polish (Asian or equivalent or as approved).

Image for design reference only Providing & supplying round low table finished with Veneer 600 x 600 mm(DXHt) with a Walnut veneered top in cross cut pattern..The top edge to be 75mm thk with rounded edge made of 18mm double BWP ply (Greenply/Century or equivalent) top including carriage of materials within all leads and lifts. Veneer to be finished with PU polish (Asian or equivalent or as approved). Please note the side tables and the center table to match in finish and look.

Image for design reference and sofa fabric as per the scheme approved by the Architects and Department. Providing & supplying single seater chair without arms of size 600x600x975mm (LxWxH) made up of hard wood frame double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The chair seat and backrest should be padded with polyurethane foam fully upholstered fabric of de-decor, dicitex retails or equivalent or as approved make with cost of fabric Rs. 750/- per meter. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the chair including carriage of material within all leads and lifts.

Image for design reference and sofa fabric as per the scheme approved by the Architects and Department. Providing & supplying single seater bar stool without arms of size 500x500x1050mm (LxWxH) seating height 750 mm with a back rest made up of hard wood frame double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved) with interconnected frame support for straingth and foot rest. The chair seat and backrest should be padded with polyurethane foam fully upholstered fabric/leatherite of de-decor, dicitex retails or equivalent or as approved make with cost of fabric/leatherite Rs. 750/- per meter. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the chair including carriage of material within all leads and lifts.

Image for design reference and sofa fabric as per the scheme approved by the Architects and Department. Providing & supplying single seater chair with arms of size 650x735x975mm (LxWxH) made up of hard wood frame double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The chair seat and backrest should be padded with polyurethane foam fully capitone upholstered fabric of de-decor, dicitex retails or equivalent or as approved make with cost of fabric Rs. 750/- per meter. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the chair including carriage of material within all leads and lifts.

Image for design reference and sofa fabric as per the scheme approved by the Architects and Department Providing & supplying single seater sofa of size 750x850x875mm (LxWxH) made up of hard wood frame double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The sofa should have coil springs in seats and sinuous spring for backrest, padded with polyurethane foam fully upholstered fabric of de-decor, dicitex retails or equivalent or as approved make with cost of fabric Rs. 750/- per meter. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the sofa. The necessary thickness of foam should be used for cushioning of front/side aprons of sofa. All open area or base or invisible part of the sofa should be fully covered with base fabric including carriage of material within all leads and lifts.

Image for design reference only Providing & supplying 1500X900x750mm pre-laminated teak ply (Greenply or equivalent) Rectangular Table top with 1.8mm thick PVC edge binding tape with knots free teak wood legs finished in PU polish (Asian or equivalent) as per approved colour/shade including carriage of materials within all leads and lifts all complete. The laminate to be approved by the HPTDC and the wood polish to match the laminate

Providing & supplying 25mm thick pre-laminated Teak Ply board (Greenply or equivalent) Oval shaped table top of size 2100x900mm with edge binding with 1.8mm thick PVC edge binding tape. The base frame to be made of 25mm thick teak wood as per shape shown in snaps finished with PU polish (Asian or equivalent) suitable for top size 2100x900mm. Wood Knots to be minimal as possible including carriage of materials within all leads and lifts. The laminate to be approved by the HPTDC and the wood polish to match the laminate

Image for design reference only( Bar Area) Providing & supplying 25mm thick pre-laminated teak ply board (Greenply or equivalent) Oval shaped table top of size 900x900mm with edge binding with 1.8mm thick PVC edge binding tape. The base frame to be made of 25mm thick teak wood as per shape shown in snaps finished with PU polish (Asian or equivalent) suitable for top size 900x900mm. Wood Knots to be minimal as possible including carriage of materials within all leads and lifts. The laminate to be approved by the HPTDC and the wood polish to match the laminate

Image for design reference only ( laminate as per specification ) Providing & supplying Laminated Rectangular work table 1200 x 600 mm(LXW) workstation in size as specified and top made 25mm thick Pre-laminated MDF board.In the workstation, all the edges are sealed with 1.8mm thick PVC edge binding tape all around, Side Panels/Gable Ends made of 25 mm thick Pre-laminated MDF board. All the edges are sealed with 1.8mm thick PVC Edge binding tape on the user side and 0.8 mm on the Top and Bottom Side. The side panels/gable ends have 2 glide screws/lavellers each for leveling of the desk. 300mm height Modesty Panel made from 18mm Thick Prelaminated MDF board. The pedestal unit with 2+1 drawers to be provided with table made of pre-laminated MDF board as per approved colour/shade with centrally lockable. The entire desk unit is assembled with standard fittings and hardwares complete. Each side panel is provided with a cutout for laying cables for the monitor and other computer. Each table has a toughened glass white board marker fixed on SS clips as shown including carriage of materials within all leads and lifts.)

Image for design reference only( laminate top as per specifications ) Providing & supplying L-shaped workstation made of 25mm thick pre-laminated MDF board (Greenply or equivalent) Rectangular front work table top of size 1500x700x750mm and side table of size 900x450x700mm. In the workstation, all the edges are binded with 2mm thick PVC edge binding tape all around, Side Panels/Gable ends made from 25mm thick pre-laminated MDF board. The side panels to have 2 glide screws/levellers each for leveling of the desk. 450mm height Modesty Panel Made from 18 mm Thick Prelaminated MDF board. The side unit to have openable shutters with adjustable shelf inside. The pedestal unit with 2+1 drawers to be provided with table made of prelaminated MDF board as per approved colour/shade with centrally lockable. The entire desk unit is assembled with standard fittings and hardwares complete. Each side panel is provided with a cutout for laying cables for the monitor and other computer including carriage of materials within all leads and lifts.

Providing & supplying an Ergonomic Medium Back Chair( 2 no’s ) is designed for comfort, to provide lumbar support, they have 360 Degree swivel base mechanism, fixed PU arm, PU base with wheel and gaslit seat height adjustment including carriage of materials within all leads and lifts of a standard approved brand .

Image for design reference and sofa fabric as per the scheme approved by the HPTDC Providing & supplying Bed with headboard of overall size 76" x 80” x 20” ( top including mattress ) King Size (LxB). The bed to be made out in single size (without any box ). The 3 sides of the bed to be done in veneer pasted on 19 mm ply / teak ply of approved make .All veneered surfaces to be finished with Melamine polish (Asian or equivalent). The headboard to be made of size 76”x 42” (WxH) height from top of the mattress, with 12mm BWP ply with 4" PU foam (Century/Sleepwell or equivalent) of density 3222Kg/m3 upholstered with fabric/ leatherite (De-decor, Dictiex Retails or equivalent) with a base price of fabnc/ leatherite of Rs. 750/per meter with quilting pattern shown in the drawing/picture. The headboard should have a 3”x3/4” sideframe finished with veneer & melamine polish respectively to match the sides of the bed. All open ply/board sides to be finished with 4mm teak margin finished with melamine polish including carriage. 2” deep rebate for the mattress to be kept as per the size ( mattress depth 10” ) the edge patti all around will be 1.5” finished In veneer .

Image for design reference –base for the drawers in powder coated frame in MS frame colour as per specifications ( antique finished ) to match the center table Providing & supplying Bed side table 480 mm x 450mm x 580( L X B x h) bed is provided with 2 nos. each side. The bed side unit having two drawers made of 18mm thick ply/board with veneer pressed and polished. (Greenply/Archid or equivalent) fitted on required telescopic runner and 200mm SS long handles finished with 3.5mm walnut veneer (Greenply/Archid or equivalent) and mellamine polish (Asian or equivalent). The inside of the drawers is finished in 0.8 mm laminate of Greenlam/Merino or equivalent. The drawer unit rest on the teak wood mellamine polish finish stand in the profile as shown as per colour/shade approved including carriage of material within all leads and lifts.

Image for design reference and sofa fabric as per the scheme approved by the Architects and Department Providing & supplying 2 seaters sofa of size 1350x800x850mm (LxWxH) made up of hard wood frame double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The arm should be finished in 75mm thick as per design/snaps. The back should have quilting as per snaps. The sofa should have coil springs in seats and sinuous spring for backrest, padded with polyurethane foam fully upholstered fabric of de-decor, dicitex retails or equivalent or as approved make with cost of fabric Rs. 750/- per meter. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the sofa. The necessary thickness of foam should be used for cushioning of front/side approns of sofa. All open area or base or invisible part of the sofa should be fully covered with base fabric. All loose cushions and padding tobe covered with approved Upholstry with Stain and water resistant 3M coating including carriage of material in all leads & lifts.

Image is for design reference only Providing & supplying Table top in 18 mm ply with 3.5mm Veneer (Greenply/Archid or equivalent) fixed in cross cut ( the grains will be arranged in a random manner) and top is finished in walnut polish with coats of melamine. The frame work for the table is in powder coated MS angle where the top fits in perfectly into the slot .The angle is rounded to perfect diameter ( 50 mm x 25 mm x 6mm thick ) .This is finished in Antique powder coated factory finish as approved. Table diameter 28" and the height is 18” . The base of the table is welded to the MS frame and finished in the same finish as the edge . Refer to the picture . Round Veneered table 28" dia including carriage of materials

Image for design reference only Providing and supplying study table 4'-0" x 1'-8" x 2'-8"(L x B x H) made of 18mm comm. board finished with 3.5mm Veneer (Greenply/Archid or Equivalent) and mellamine polish (Asian or equivalent). The legs to be made of teak wood with frame finished with mellamine polish as approved colour/shade shown in the attached picture. The table top should have a 100x100mm front pocket skirting to be provided in veneer & mellamine polish finished including carriage of material within all leads and lifts.

Image for design reference and sofa fabric as per the scheme approved by the Architects and Department Providing & supplying study chair without arms of size 520x600x850mm (LxWxH) made up of hard wood frame double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The chair seat and backrest should be padded with polyurethane foam fully capitone upholstered fabric of de-decor, dicitex retails or equivalent or as approved make with cost of fabric Rs. 750/- per meter. The thickness of foam should be 3" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the chair. The necessary thickness of foam should be used for cushioning of front/side approns of chair. All loose cushions and padding tobe covered with approved Upholstry with Stain and water resistant 3M coating including carriage of material within all leads and lifts

Providing & supplying Bed with headboard of overall size 76" x 80” x 20” ( top including mattress ) King Size (LxB). The bed to be made out in single size (without any box) .The 3 sides pattis ( 8"deep ) of the bed to be done in veneer pasted on 19 mm ply / teak ply of approved make. All veneered surfaces to be finished with Melamine polish (Asian or equivalent). The headboard to be made of size 76"x 42”( from the mattress top) as per the design seen in the reference picture . The headboard to be in a mix of wood runner with perforations on top to match the perforation on the foot side .The headboard to have infill panels in veneer finished with veneer & melamine polish respectively to match the sides of the bed. All open ply/board sides to be finished with 4mm teak margin finished with melamine polish including carriage. The foot board to have the same design as headboard in wood and veneer infill. 2” deep rebate for the mattress to be kept as per the | size (mattress depth 10” ) the edge patti all around will be 1.5” finished in veneer.

Providing and supplying Bed side table 1'-8" x 1'-4" x 18" (L X B x h) 2 nos. each side made of 18mm ply/board finished with 3.5mm veneer (Greenply/Archid or equivalent) on exposed surfaces and walnut mallamine polish (Asian or equivalent). The bed side unit having one drawer made of ply/board fitted on telescopic runners (Hettich/Ozone or equivalent) and 100mm SS long handles. The inside of the drawers is finished in 0.8 mm laminate of Greenlam/Merino or equivalent including carriage of material within all leads and lifts.

Image for design reference only Providing & supplying chair ( rooms ground floor ) 650x550x875mm (LxWxH) made up of hard wood frame double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per designor as approved finished with PU polish (Asian or equivalentor as approved). Chair back and seat Internal frame to befixed with Heavy duty jalebi spring, padded withpolyurethane foam fully capitone upholstered fabric of dedecor, dicitex retails or equivalent or as approved makewith cost of fabric Rs. 750/- per meter. The thickness offoam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 IgnitionSource O (Cigarette)) to provided extra softness & comfortto the chair. The necessary thickness of foam should be used for cushioning of front/side approns of chair. All loose cushions and padding tobe covered with approved. Upholstry with Stain and water resistant 3M coating

Image for design reference only Providing and supplying Round balcony table 600 MM dia and height is 750mm. The top of the table is in glass of tile mosiac pattern ( as seen in the reference picture ) including carriage of materials within all leads and lifts.

Image for design reference only Providing and supplying Balcony chairs MS powder coated chair 450 mm dia satndard chair in MS powder coated hollow pipe frame work including carriage of materials within all leads and lifts. The seat would be in wooden.

Image for design reference Providing and supplying Garden Benches 1600 mm x 700 mm Materials Used - Leg Support: Cast Iron | Seating Material Slats/Strips - 4mm thick and strong FRP (FibreReinforced Plastic)Leg Support painted with Spray Paint for shiny look . Termite proof seating material and 100% washable and waterproof. Can be easily dismantled and reassembled. Can be stored in a box in knocked down condition. Supplied in a carton in knocked down condition. Buyer need to reassemble at their end. Easy and convenient portability to lift and shift Strong and durable design to take load up to 350 Kg. distributed across the length including carriage of materials within all leads and lifts.

Image for design reference only Providing and supplying outdoor deck furniture 600 mm dia round table height is 800mm Structure made of Mild Steel with 18 Gauge thickness (1.6 mm wall thickness) Structure frame painted with Epoxy Berger Paint which helps avoid corrosion Heavy duty build quality to tolerate maximum seating weight upto 120 kg per seater, export quality metal frame and rattan used UV Protected HPDE high quality wicker is used for this balcony sofa set which is resistant to Sun heat and Rain Includes 4 Indian made heavy duty chairs and 1 table set with 10mm toughened Glass Top including carriage of materials within all leads and lifts.

Image for design reference and sofa fabric as per the scheme approved by the Architects and Department Providing & supplying stackable conference room chair without arms of size 520x630x850mm (LxWxH) made up of hard wood frame double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The chair seat and backrest should be padded with polyurethane foam fully capitone upholstered fabric of de-decor, dicitex retails or equivalent or as approved make with cost of fabric Rs. 750/- per meter. The thickness of foam should be 3" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the chair.

Image for design reference only Providing and supplying Confrence Hall table of 1200 MM Dia made of prelaminated MDF board (Greenply or equivalent) as per approved colour/shade. Table top edge to be binded with 1.8mm thick PVC edge binded tape all around. The table top to be properly screwed with supporting base for proper strength. Base of the table is in MS powder caoted as per colour/shade approved including carriage of materials within all leads and lifts all complete.

Image for design reference and sofa fabric as per the scheme approved by the Architects and Department Providing & supplying 3 seaters sofa of size 2150x750x875mm (LxWxH) made up of hard wood frame double dowelled for proper strength, glued and screwed/nailed properly as per design/snaps attached. The legs should be made of knot free teak wood as per design or as approved finished with PU polish (Asian or equivalent or as approved). The sofa should have coil springs in seats and sinuous spring for backrest, padded with polyurethane foam fully upholstered fabric/leatherite of de-decor, dicitex retails or equivalent or as approved make with cost of fabric/leatherite Rs. 750/- per meter. The thickness of foam should be 4" thick having density of 40±2Kg/m3 with 1/5" soft foam on base foam (sleepwell, Century or equivalent conforming to BS 5952 Part 1 1979 Ignition Source O (Cigarette)) to provided extra softness & comfort to the sofa. The necessary thickness of foam should be used for cushioning of front/side approns of sofa. All open area or base or invisible part of the sofa should be fully covered with base fabric including carriage of material within all leads & lifts.

Image for design reference only Providing & supplying round low table finished with Veneer 1300 x 320 mm(DXHt) with a Walnut veneered top in cross cut pattern with a 6mm thk nickel finished MS section inserted in the legs and table top as shown in the drawing/snap.The top edge to be 75mm thk with rounded edge made of 18mm double BWP ply (Greenply/Century or equivalent) top including carriage of materials within all leads and lifts. Veneer to be finished with PU polish (Asian or equivalent or as approved).