Himachal Pradesh Tourism Development Corporation Tender

Centering and shuttering with steel plates including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform as per the diretion of Engineer in Charge including carriage of materials within all lead, lifts and heights.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size) as per the diretion of Engineer in Charge including carriage of materials within all lead and lifts .

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Hot rolled deformed bars as per the diretion of Engineer in Charge including carriage of materials within all lead, lifts and heights . Fe 500/Fe 500D TATA/Sail/Jindal /Panther /JSPL / Shyam steel or as approved by Engineer-In-Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 upto plinth level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) as per the diretion of Engineer in Charge including carriage of materials within all lead, lifts and heights .

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 foundation and plinth in Cement mortar 1:4 (1 cement :4 coarse sand) as per the diretion of Engineer in Charge including carriage of materials within all lead, lifts and heights.

Structural steel work riveted, bolted or welded in built up sections, In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works as per the diretion of Engineer in Charge including carriage of materials within all lead, lifts and heights as approved by Engineer -In-Charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer as per the diretion of Engineer in Charge including carriage of materials within all lead, lifts and heights .

15 mm cement plaster 1:4 (1 cement: 4 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall as per the diretion of Engineer in Charge including carriage of materials within all lead, lifts and heights .

Painting Two or more coats on new work with synthetic enamel paint of Asian/Nerolac/Berger or equivalent make of approved brand and manufacture to give an even shade as per the diretion of Engineer in Charge including carriage of materials within all lead, lifts and heights .

Polishing two or more coats with malamine polish of required shade (in glossy/matt finish) on new wood and wood based surfaces to give an even surface including cleaning the surface of all dirt, dust and sand papered smooth and including a coat of wood filler including carriage of materials within all lead, lifts and heights as per the diretion of Engineer in Charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) including carriage of materials within all lead, lifts and heights. Jindal/Hindalco/ Nalco or equivalent make.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC15) including carriage of materials within all lead, lifts and heights. Jindal/Hindalco/ Nalco or equivalent make.

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer- in-Charge Pre-laminated particle board with decorative lamination on both sides including carriage of materials within all lead, lifts and heights. Merino/Century/Kit ply or equivalent make as approved by Engineer-In-Charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm) including carriage of materials within all lead, lifts and heights . Jindal/Hindalco/ Nalco or equivalent make as approved by Engineer-In-Charge.

Providing and fixing cup board of 19 mm thick commercial board i.e. sides, shelves (with shutter) and back side 9 mm thick commercial ply inside sunmica 1.0mm thick, 4 mm Teak Ply on shutter and sids, 20 mm X5 mm Teak wood margin, ornamentle brass handles, hinges, cup board blocks and catchers etc fixed with necessary nails, favicol and screws etc complete as per the diretion of Engineer in Charge ncluding carriage of materials within all lead, lifts and heights. Merino/Century/Kit ply or equivalent make as approved by Engineer-In-Charge.