Himachal Pradesh Irrigation And Public Health Department Tender

Capacity (in LPS) 1.55 LPS

Dia of R/Main (in mm) 40 MM

Length of rising main (in mtr.) 1850 metres

1 set of 20 HP

Providing and fixing of auto control panel with push button star delta starter( 1 No.) for reciprocating /centrifugal pump of L&T and reputed make fabricated with M.S. sheet and angle stand duly painted and complete with internal wiring, comprising of main switch of suitable Amp., T.P. volte meter, copper busbar, ameter, hour run metre, phase indicating lamps with GMS based, remote start/stop operation call/SMS for feedback regarding running of pumps & breakdown message, timer scheduling for fixed hour in a day, imbuilt protection against overload/ undervoltage, dry run, single phase preventer, inbuilt GPS tracker, phase reversal configurable volt/current limits with a facility to access the system through minimum 10 No. authenticate mobile Nos. complete in all respect, including intire carriage of materials all leads and lifts, installation and testing at site with entire saisfaction of engineer-in-incharge.(all meters to be installed shall be DIGITAL)

Pumping Machinery 2nd Stage

Supply, erection, testing & commissioning of reciprocating /centrifugal pumping set of reputed make Kirlosker/M&P/KSB/ BS/Johnston/Worthington or any other reputed make conforming to BIS 1520-1980 with upto date ammendments read with BIS 9137-1978 or latest edition to handel clear water having characteristics as mentioned below in ltem no 3(A), with impelleres,casing ring priming funnels & shaft sleeves of bronze , shaft of steel of steel with cast iron casing of suitable capacity coupled directly through a flexible coupling on a common base plate of cast steel/ Mild steel to BHEL/ Kirlokar/ NGEF/Crompton/Siemen /jyoti/GEC make slip ring /squirrel cage screen protected drip proof induction electric motor suitable for operation on the data given below i/c the cost of all the accessories in all leads and lifts & carriage at the site sites as per direction of Engineer-in - charge. (Note:- Tender to be called for per set not for per HP rate)

Total Head in mtrs (i/c depth of Column Pipe in case of t/well) : 485 mtr

Capacity (in LPS) 1.55 LPS

Dia of R/Main (in mm) 40 MM

Length of rising main (in mtr.) 1250 metres

1 set of 20 HP

Providing and fixing of auto control panel with push button star delta starter( 1 No.) for reciprocating /centrifugal pump of L&T and reputed make fabricated with M.S. sheet and angle stand duly painted and complete with internal wiring, comprising of main switch of suitable Amp., T.P. volte meter, copper busbar, ameter, hour run metre, phase indicating lamps with GMS based, remote start/stop operation call/SMS for feedback regarding running of pumps & breakdown message, timer scheduling for fixed hour in a day, imbuilt protection against overload/ undervoltage, dry run, single phase preventer, inbuilt GPS tracker, phase reversal configurable volt/current limits with a facility to access the system through minimum 10 No. authenticate mobile Nos. complete in all respect, including intire carriage of materials all leads and lifts, installation and testing at site with entire saisfaction of engineer-in-incharge.(all meters to be installed shall be DIGITAL)

Excavation in foundation and trenches in all type of soil such as pickwork jumper work Kankar, moorum, shingles including decomposed soft and hard rock etcupto all heights stacking the excavated earth not more than 3mtrs clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinths sides of foundations etc. consolidating each deposited layers by ramming and watering and then disposing of all surplus excavated earth in all leads and lifts as per the direction of Engineer in-charge.

Providing and laying cement concrete 1:4:8(1cement:4approved sand:8app.graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth and as per the direction of Engineer-in-charge including entire carriage of material upto all leads and lifts.

Providing and laying cement concrete 1:1.5:3(1cement:1.5approved sand:3approved graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:-

Foundation and plinth including entire carriage of material upto all leads and lifts.

Wall (any thickness but not less than 0.1m thickness) attached pillasters,buttresses plinth and string courses etc. from top to foundation level upto floor two level and as per the direction of Engineer-in-charge.including entire carriage ofmaterial upto all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish. Including centring,shuttering strutting and propping etc. with wooden battens and ballies height of propping and centring below supporting floor to ceiling not exceeding 4mtrs and removal of the same for insitu reinforced concrete and plain concrete work in:-

Flat surfaces such as soffits of suspended floors, roofs, landings and the like, floors etc., up to 200mm in thickness.

Vertical surface such as wall of (any thickness) partition and the like including attached pillaster buttresses plinth and string courses and like and as per the direction of Engineer-in-charge .including entire carriage of material upto all leads and lifts.

Providing and laying reinforced cement concrete work 1:2:4 ( 1 cement :2 sand :4 graded stone aggregate 20 mm nominal size ) excluding cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landings, shelves and their supports balconies beams, girders bressumers and cantilevers upto floor two level in all heights and depths includiing all leads lifts and carriage of material at site and as directed by the Engineer Incharge.

Providing tor steel reinforcement for RCC work including bending,binding and placing in position complete upto floor two level.as per the direction of Engineer-in-charge including entire carriage of material upto all leads and lifts.

Providing and fixing MS sheet manhole cover of 600 X 600mm to existing storage tank made of angle iron 40mm x 4mm base plate and manhole frame 35mm X 35mm X 4mm with MS sheet 2mm thick including cutting, welding, red lead paint and locking arrangement with lock complete including all leads, lifts and carriage of material at site and as per the direction of Engineer Incharge.