Himachal Pradesh Irrigation And Public Health Department Tender

a) LWL in sump well (h) 2601.00

b) Shaft level 2604.00

c) Level at discharge point 2870.00

d) Suction lift -ve

e) Dynamic head 308.05

f) StTIC HEAD 266.00

Risining Main

a) Length 650.00

b) Dia 32.00

Pumping hours 6.00

Altitude of installation above MS

Characterstics of water Clear water with turbidity up to 50 PPM.

a) Temperature centigrade. 25 degree degree centigrate.

Providing supplying and installation of control panel with required accessories for motor offered above and having protection of motor on occurance of faults { Triping on occurance of fault(s) i.e. Moisture, high motor temperature, dry running, reverse rotation, Single phasing, voltage imbalance, overload and short circuit } and indiation thereof by glowing fault lamp ; for motors above 15 KW another protection of Mechanical seal failure shall also be provided in addition to above protections complete in all respect with in all leads and lifts and to entire satisfaction of engineer -in -charge

Providing , laying and installation of PVC Insulated un- armoured aluminium conductor cable Havells/Gloster/Khaitan /RR Kabel make of suitable size and suitable for motor offered under item No I complete with flexible pipe and couplers from HPSEB meter to Panel, switch, starter complete job, The type and size shall be subject to approval of Electrical authorities and in case of its non acceptance the same shall be replaced free of cost by the tenderer complete in all respect with in all leads and lifts and to entire satisfaction of engineer -in -charge

16 sq. mm , 3.0 core

Providing , laying and installation of 3 core flat submersible pump cable from starter to pump of Havells/ksb/L&T/RR Kabel make of suitable size and suitable for motor offered under item No I complete with flexible pipe complete in all respect with in all leads and lifts and to entire satisfaction of engineer -in -charge

4.00 mm2

Proiding and fixing of cast steel double flanges Non Return Valve 40 mm dia with flange table -5 make LEADER/KIRLOSKER/ KILBURN make having class PN-10.0 capable of withstanding nominal seat pressure of 52kg/cm2. the Non Return Valve should be confirming to BIS -1414 with up to date ammendments including cost of Nut & Bolts and GAsket and complete fixing new valve by all means complete job in all respect. in all leads and lifts and to the entire satisfaction of Engineer in Charge.

Proiding and fixing of cast steel double flanges Sluice Valve 40 mm dia with flange table -5 make LEADER/KIRLOSKER/ KILBURN make having class PN-1.6 capable of withstanding nominal seat pressure of 52kg/cm2. the Sluice Valve should be confirming to BIS -1414 with up to date ammendments including cost of Nut & Bolts and GAsket and complete fixing new valve by all means complete job in all respect. in all leads and lifts and to the entire satisfaction of Engineer in Charge.

Providing and fixing steel wire rope 10mm Thick for holding the column assembly and pump set in bore well to avoid falling of assembly and pum set in bore well including comlete arrangement of fastening etc.complete in all respect as per the direction of Engineer-In.Charge.

Providing and fixing MS sheet box size (0.60x0.30x0.90mm fabrocated with angle irong of four legs mounted in cement concrete 1:3:6 for electric metred starter switch and other accessories with locking arrangement complete.

Providing and fixing MS Clamps to hold the pump set in the bore well including required bolt and nuts complete in all respect as per entire satisfaction of Engineer-in-charge.

Erection Charges including labour charges, electrical connection , lowering of etc complete in all respect as per the entire satisfaction of Engineer-in-charge.

Excavation in foundation trenches etc. in earth work lift up to 1.5 mtrs. Stacking the excavated soil not more than 3 metres away from the edge of excavation and then returning the stacked soil in 15 cm layers when required in to plinth and sides of foundations, consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres.

Laying,jointing ( by way of circumfrential butt welded joints by electrical arc welding ) and testing of Galvanised mild steel tubes (GI Pipes) of following dia meters confirming to BIS 1239-2001 (latest with upto date amendments) having wall thickness as per code with bevelled / plain ends in a random length of 4 to 7 meters, including manufacturing reducers/ tapers , all short pieces, bends etc. as per site requirement made from parent tubes . The laying of pipe will include all operation such as cutting, welding, jointing, fabrication of bends, tees etc. including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respects to the satisfaction of the Engineer in charge. The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The damaged portion of the pipes and specials made form the parent tube during welding or otherwise shall be provided anticorrosive treatment by applying two coats of anticorrosive bituminous paint over a priming coat as per AWWA specifications C-203-1978. The welding electrodes shall be as per IS 814 of Advani Oerlikon/ L&T or ISI marked make. The rates also includes entire carriage of material, flushing, cleaning & hydraulic testing complete to the best satisfaction & direction of Engineer in charge with in all leads and lifts. (Earth work in trenches will be measured and paid for separately). GI Pipe 32mm ( LC)

Cutting in earth work and disposal of excavated earth work upto a lead of 20 metre

Excavation in foundation trenches etc. in earth work lift up to 1.5 mtrs, Stacking the excavated soil not more than 3 metres away from the edge of excavation and then .returning the stacked soil in 15 cm layers when required in to plinth and sides of foundations, consolidating each deposited layer watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres in pick jumper work.

Providing and laying cement concrete 1:3:6 (1 Cement :3 Sand: 6 graded stone aggregate 40mm nominal size)and curing complete excluding the cost of form work in foundation and plinth including all carriage of materials upto all leads and lifts complete in all respects.

Providing and laying cement concrete work 1:11/2 Sand : 3 graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and reinforcement for reinforced concrete work in

In foundations ,footings bases of columns and the like and mass concrete work complete in all respects

In Walls any thickness (but not less than 0.10meter thickness including attached pilasters, buttresses plinth and string courses etc. from top of foundation(level) upto floor two level including all leads and lifts etc. complete in all respects

Suspended floors, roofs, landings, shelves and their supports, balconies, beams, and girders, bressumers and cantilevers upto floor two level including all leads and lifts etc. complete in all respects

Providing form work with mild steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as 10 give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4 meters and removal of the same for insitu- reinforced concrete work and plain concrete work in:-

Vertical surfaces such as walls(any thickness )partition and the like including attached pillasters, buttresses plinth and string courses and like including all leads and lifts etc. complete in all respects.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like floors etc, upto 200mm in thickness including all leads and lifts etc, complete in all respects.

Edges of slab including all leads and lifts complete in all respects.

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete upto floor two level including cost of binding wires and carriage of materials upto all leads and lifts complete in all respects.

Prov. and fixing MS man hole cover of size 600 x 600 mm made up of 3.15 mm Thick plain MS sheet fixed in angle iron frame frame of 50x50x5mm supported with MS flat of 50x5mm at center of sheet including fising hold fast ,hinges and locking arrangement and lock of medium size etc complete in all respects.

Laying and jointing in trenches GMS Tubes (Light class) tube fitting for inlet , out lets and over flow pipe including all leads and lifts complete in all respect.

32mm

50mm

Providing and fixing gun metal wheel valve(with hand wheel) as per specification of the Engineer-in -Charge in all leads.

32mm

50mm