Himachal Pradesh Irrigation And Public Health Department Tender

Chieselling /wedging out of rock where blasting is prohibited

Excavation in foundation trenches in earth work in pick work, jumper work within all leads and lifts, stacking the excavated soil not more than 3 mtrers clear from the edge of excavation and then returning the stacked soil in15cm layers when required into plinths sides of foundation etc. consolidating each deposited layer by ramming watering and then disposing of all surplus excavated earth as direction with in all leads and lifts as per directed by the Engineer-in-Charge. (i.e. Pick work-50% +Jumper Work-50%)

Providing and laying cement concrete 1:4:8(1: cement :4 sand :8 graded crushed stone agg. of 40mm. nominal size) and curing complete excluding the cost of form work in foundation and plinth with in all leads and lifts as per the direction and entire satisfaction of the Engineer-in-charge.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering , strutting and propping etc. with wooden battens and ballies height of propping and centering below supporting floor to ceiling not exceeding 4meters and removal of the same for insitu reinforced complete in all respect within all leads and lifts.

In vertical surfaces such as ;walls(any thickness) partitions and the like in-cluding attached pillasters,buttresses,plinth and string courses and the like.

In foundation,footin,bases of columns etc.and mass concrete.

Columns,pillars,posts and struts :- Square, recanguar , polygonal in Plan

Sides and soffits of beam haunching cantilevers,bressumers and lintle not exceeding 1.00 Metres in depth all heights from from.

Sloping portion where inclination is more than 30O

In flat surface such as;soffits of suspended floor,roofs,landings and the like floor to level etc.upto 200mm.thickness.

Providing and laying cement concrete 1:4:8 with (1: cement :4 sand :8 graded crushed stone agg. of 40mm. nominal size) and curing complete excluding the cost of form work in foundation and plinth with in all leads and lifts as per the direction and entire satisfaction of the Engineer-in-charge.

Providing, laying cement concrete 1:2:4 (1cement: 2sand: 4graded stone agg., 20mm nominal size) & curing complete excluding the cost of form work and reinforcement for reinforced concrete work in.

Foundation,footin,bases of column and like mass concrete.

COLUMNS, PILLARS POSTS AND STRUTS UPTO FLOOR TWO LEVEL.

IN SUSPENDED FLOOR,ROOFS,LANDING &SHELVES & THEIR SUPPORT , BALCONIES,BEAMS,GIRDERS.BRESSUMERS & CANTILEVER UPTO FLOOR TWO LEVEL.

Providing and laying cement concrete work 1:1.5:3(1cement:1.5sand: 4 graded stone aggregate 20mm nominal size ) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in :-

Wall(any thickness but not less than 0.10metre) including attached pillaster-ing buttresses plinth and string courses etc.from top of foundation level upto any floor level.

Foundation,footing,bases of columns and the like and mass concrete.

Columns,pillars posts and struts upto any floor level.

In suspended floor roof landings and shelves and their supports balconies, beam,girders, bressumers and cantilevers upto floor level

Providing Tor steel reinforcement for RCC work including bending, binding & placing in position complete upto floor two level complete in all respect within all leads and lifts..

Wire crates of GI wire filled with boulders with square cut faces against the wire (Wire create to be measured and paid for separatly) including carriage of materials complete within all leads & lifts as per the direction and entire satisfaction to the Engineer in Charge

Wire crates made of G.I wire filled with boulders with square cut faces against the wire (Boulder filling to be measured and paid for separatly ) GI wire 5mm thck corresponding to SWG-8 15mmx 15mm mesh including carriage of materials complete within all leads & lifts as per the direction and entire satisfaction to the Engineer in Charge

Providing and laying cement concrete 1:3:6 (1cement:3sand: 6graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation & plinth complete in all respect within all leads and lifts as per the direction and entire satisfaction to the Engineer in Charges.

Steel work welded in built up section trusses and framed work included cutting hoisting fixing in position and applying a priming coat of red lead paint in gratings, Frame,Gaurd Bar, Ladders, Railing, Brackets, and similar work complete in all respect and direction and satisfaction of the Engineer-in-charge.

Providing and laying cement concrete using concrete mix of " M-25 " not Longer than 1:1.5:3 with stone aggregate 20 mm & Down guage nominal size and curing complete excluding the cost of form work & reinforcement for reincforcement concrete work in :

Foundation,footing,bases of columns and the like and mass concrete.

In wall(any thickness but not less than 0.10metre) including attached pillaster-ing buttresses plinth and string courses etc.from top of foundation level upto any floor level.

PROVIDING FOR RCC WORK SMOOTH FINISHING OF THE EXPOSED SURFACE WITH CEMENT MORTOR 1:3 (1CEMENT : 3 SAND) COMPLETE IN ALL RESPECT IN ALL LEADS & LIFTS.

Providing and fixing MS Rungs 20mm wide chequarred/ripped non slipery surface i/c fixing in position with 1:3:6 complete in all respect within all leads and lifts as per the direction and entire satisfaction to the Engineer in Charges.

Brick work using common burnt clay building bricks 2nd class in cement mortor 1:6(1 cement 6 sand ) complete in all respect within all leads and lifts and as per directions and satisfaction of Engineer in Charge. In foundation and plinth

Brick work using common burnt clay building bricks 2nd class in cement mortor 1:6(1 cement 6 sand ) complete in all respect within all leads and lifts and as per directions and satisfaction of Engineer in Charge. In superstructure upto floor two level.

Providing wood work in frames of doors, windows and other frames wrought framed and fixed in position with second class deodar wood.

Providing and fixing wood paneled glazed or paneled and glazed shutters for doors, windows and clear story 40mm thick windows including bright finished black enameled iron with necessary screws with second class deodar wood 40mm thick.

HALF BRICK MASONRY IN COMMON BURNT CLAY BUILDING BRICKS IN CEMENT MORTOE 1:4( 1 CEMENT:4 SAND) IN SUPERSTRUCTURE ABOVE PLINTH LEVEL UPTO FLOOR TWO LEVEL 2nd CLASS BRICK.

POINTING ON BRICK WORK WITH CEMENT MORTOR 1:3(1CEMENT:3SAND) RAISED AND CUT POINTING complete in all respect within all leads and lifts and as per directions and satisfaction of Engineer in Charge.

6 mm thick cement plaster to ceiling in CM 1:3 (1Cement :3 Sand) complete in all respect within all leads and lifts and as per directions and satisfaction of Engineer in Charge.

15mm thick cement plaster in single coat of rough sides of bricks/ concrete/stone walls for interior plastering upto floor two level including arrises, internal rounded angles chamber and rounded angles not exceeding 80mm in girth and finished even and smooth in Cement mortar 1:6(1 cement: 6 sand) complete in all leads and lift.

20mm thick cement plaster in single coat of rough sides of bricks/concrete stone wall for interior plastering upto floor two level including arrises, internal rounded angles chamber and rounded angles not exceeding 80mm in girth and finished even and smooth in Cement mortar 1:6(1 cement: 6 sand) complete in all leads and lift as specification and direction of the Engineer-in-charge.

Providing and fixing M.S. Grills of required pattern in wooden frame of window etc. with MS Flat square or round bar with round headed bolt nut by screws plain Grills within all leads and lifts as per the direction of Engineer-in-charge.

Providing and fixing wire gauge shutters using galvanized MS wire gauge of IS gauge designation 85 G.with wire of 0.56mm for doors window & clearestry windows including bright finished black enameled iron hinges with necessary screw.40mm thick 2nd class Deodar wood.

WHITE GLAZED TILES 6mm IN FLOORING ,TREAD ,STEPS & LANDING LAID ON A BED 12 mm THICK CEMENT MORTOR (1:3) FINISHED WITH FLUSHED POINTING IN WHITE CEMENT.

Stone/Boulder filling under floors/behind retaining walls under floor complete in all respect within all leads and lifts and as per directions and satisfaction of Engineer in Charge.

Providing and fixing 40x3mm flat iron hold fast 40cm long including fixing to frames with 10mm dia meter bolts, nuts & wooden plug and emedded in cement mortar block 30x10x15cm 1:3:6(1cement:3 sand:6 graded stone agg., 20mm nominal size) complete in all respect within all leads and lifts as per the direction of Engineer-in-charge.

White washing with lime on undercated walls surfaces (two coats) to give an even shade including thoroughly bromming the surface to remove all dirt, dust mortar dirt and other foreign matter complete in all respect within all leads and lifts as per the direction of Engineer-in-charge.

Distempering with dry distemper of approved brand and manufacture (Two coats)and of required shade on undercoated wall surface to give even shade over & including priming coat of whiting after thoughly brusing the surface clean of all grease, dirt loose pieces of scales including preparing the surface even and sand papere smooth.

Finishing wall with water proofing cement paint of approved brand & manufacture & of required shade on undecorated wall surfaces ( two coats) to give an even shade after thotoughly brushing the surface to remove all dirt & remains of loose powdered materials complete in all respect within all leads and lifts.

Providing and fixing of MS Sliding door bolts of following size with necessary screw etc., complete in all respect within all leads and lifts as per the direction of Engineer-in-charge.

300x16mm

250x16mm

Providing and fixing of MS Tower Bolt (Barrel type) of following size with necessary screw etc., complete in all respect within all leads and lifts as per the direction of Engineer-in-charge.

200x10mm

Providing and fixing of MS Handle of following size with necessary screw etc., complete in all respect within all leads and lifts as per the direction of Engineer-in-charge.

125mm

100mm

Applying priming coat over new wood & wood based surface after and including repairing the surface by thoroughly cleaning oil grease dirt & other foreign matter & papering & knotting with ready mixed paint brushing wood primer pink complete in all respect within all leads and lifts as per the direction of Engineer-in-charge.

Painting two coats(excluding priming coat) on new wood and wood surface with ready mixed paint brushing to give an even shade including cleaning of all dirt, dust & other foreign matter sand papering and stopping with ready mixed paint other than white complete in all respect within all leads and lifts as per the direction of Engineer-in-charge.

Providing plinth protection 50mm thick cement concrete 1:3:6(1cement:3sand:6graded stone agg., 20mm nominal size) including finishing the top surface concrete smooth complete in all respect within all leads and lifts as per the direction of Engineer-in-charge.

PROVIDING UNDER LAYERS FOR PLINTH PROTECTION OF 75 mm THICK ( UNCOLIDATED) BED OF DRY BRICK/STONE AGGREGATED 40 mm NOMINAL SIZE WILL RAMMED & GROUTED WITH FINE SAND INCLUDING PREPARATION OF GROUND.

Squarred rubble stone masonry coursed with hard stone of approved quality in Super Structure above plinth level and upto floor two level in CM 1:6 complete in all respect within all leads and lifts.

Providing & Fixing of Fencing panel of size 2.40m x 1.20 m devided in two Panels of 1.20m X 1.20m by fixing T iron at centre fitting with wire mesh 25X25mm mesh welded to M.S.Angle frame all around with M.S Flats cover and seven Nos. of holdfast including cutting welding, painting with red oxide paint completein all respect and as per the entire satisfaction of the Engineer In charge.

Providing and laying cement concrete 1: 6: 12 (1Cement: 6 sand:12 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work foundation and plinth complete in all respect within all leads and lifts.

PROVIDING & FIXING PRESSED STEEL DOORS FRAMES MANUFACTURED FROM COMMERCIAL MILD STEEL SHEET OF 1.25 mm THICKNESS INCLUDING HINGES,JUMP LOCK JAMB,BEED & IF REQUIRED ANGLE THRESHOLD OF MILD STTEL ANGLE OF SECTION 50 x 25 mm OR BASE TIES OF 1.25 mm PRESSED MILD STEEL WELDED OR REGIDLY FIXED TOGETHER BY MECHANICAL MEANS,ADJUSTABLE LUGS WITH SPLIT & TAILS TO EACH JAMB INCLUDING STEEL BUTT HINGES 2.5 mm THICK WITH GUARDS,LOCK STRIKE PLARE & SHOCK AS SPECIFIED & APPLYING A COAT OF APPROVED STEEL PRIMER AFTER PRETREATMENT OF THE SURFACE AS DIRECTED BY ENGINEER IN CHARGE. (Profile as required for double rebate frames)

40 MM THICK CEMENT CONC. FLORRING 1:2:4 (1 CEMENT:2 SAND:4 GRADED STONE AGGREGATE 20 mm NOMINAL SIZE ) LAID IN ONE LAYER FINISHED WITH A FLOATING COAT OF NEAT CEMENT complete excluding the cost of form work foundation and plinth complete in all respect within all leads and lifts.

Excavation in foundation, trenches ( for pipes & pits) upto all depths in all classification of earth work such as pick work, jumper work, saturated soil including bailing and pumping out water, blasting soft/ hard rock or chieselling soft/hard rock where blasting is prohibited in all lifts including trimming and dressing of sides, leveling of beds to correct grade i/c shoring /strutting , planking, timbering & dewatering wherever required, stacking the useable & unuseable material /soil separately & after laying jointing & testing of pipes, returning the useable soil in trenches in 15 cm layers including consolidating of such deposoited layer by ramming & watering & then disposing of all surplus excavated soil /unusable material as directed with in all leads & lifts including restoration, unmetalled surfaces to its original condition & including cost of diversion for traffic, night signals, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respects with in all leads & lifts as per directions of Engineer-in-charge. (Pick work-50% & Jumper work-50%)

Providing & laying, jointing & testing of bevel edged MSERW pipe with circumfrential butt welded (94%) joints by electrical arc welding (welding thickness shall be equal to pipe wall thickness) and welding of M.S flangs (6%) dully welded & testing of MSERW pipe of following dia conforming to BIS 3183-20077 required grade ( latest with up to date amendments having wall thickness as specified below and capable of with standing required test pressure in a rendom length of 5.5 to 6.5 mtr,including manufacturing reducers/tapers,bends of required degree, all shot pices etc as per site requirement made from parent tuble. The laying of pipe shall also including flanges joint duly welded in three layers two Inner & one outer where ever required as per the direction of Engineer-in charge (earth work & trenches and the cost of proving flanges l/c nuts and bolts and gasket will be measured and paid for separatly )and all operation suach as cutting, welding, jointing fabrication of Tee including lowering and laying in excavated trenches to Insure required level including flushing, cleaning and hydrolic testing complete in all respect to the satisfaction of the Engineer in charge. The pipe shall be factory galvanized (zinc coating both inside and outside) as per relevent IS standards and the damaged portion of the pipe and special (if damaged during laying jointing operation of pipe) made from the parant tube, shall be provided anticorrosive trearment by applying two coats of anticorrosive bituminous paint over a priming coats as per AWWA specification C-203-1978. The welding eictrodes shall be as per 15 814 of Advani oerlikon /L & T or IS marked make The rate also include entire carriage of material, Flushing, cleaning & Hydrolic testing, OP test butt welded joints comaplete in all respect and to the best satisfaction and direction of Engineer In charge with in all leads and lifts Note negitive ance of wall thickness should not be more than 3%. Pipe make Surya/Jindal/Tata

MSERW pipe 250mm dia pipe grade L-290 or X42 having wall thickness 4.80mm Flange Table-5 RD 0 to 45 Mtr (Head weir to intake (booster stage) and RD 260 to 780 Mtr= 520 mtr (Pump house to delivery tank)

MSERW pipe 250mm dia pipe grade L-290 or X42 having wall thickness 4.80mm Flange Table-11 RD 0 to 260 Mtr= 260 mtr

Providing and welding MS flanges (6% joint flange) confirming to following table as per IS 6392-1971 (latest with upto date ammendments) with plain end MSERW pipe by two layer outer face and one layer in inner face to make the joint leak proof ( the cost of providing & laying of GI/MSERW pipe to be measured and paid for saparetaly). The weldeding of flange should be confiming to IS 816-1969 with electrodes as per IS: 814-2004 and required Numbers of nuts and bolts conmfriming to IS :1364. with i/c cost of gasket sheet nut and bolts the thickness of gasket sheet not less than 3mm thick confirming to IS 2712-1998. The work shall be done to the entire satisfaction of Engineer-in-charge within all leads and lifts.

250mm dia Table-5 RD 0 to 45 Mtr of booster stage and RD 260 to 780 Mtr of main stage i.e .Pump house to delivery tank

250mm dia pipe Flange Table-11 RD 0 to 260 Mtr= 260 mtr

Providing , fixing , Jointing & Testing of MSERW Bend 5 times dia of pipe with 3 cut (4 Pieces) of various degree Fabricated from parient tube of 250 mm dia flanged with flange Table-5 & 11 at Various RD's including incersion of Gasket sheet washer 3mm thick and Nuts and bolts complete in all respect.

Providing and fixing of Cast Iron air releasing valve of reputed make 50 mm dia class PN-10 test pressure 10.20 Kg/cm2 complete in all respect .

Supply Installation Testing & Commissioning of of Submersiblel Pumping Set of Calama /KSB/Crompton /SU/Johnston /Sabar conforming to BIS-8034-1976 (Latest) suitable for clear water fitted with bronze Impellers or suitable alloys directly cooupled to squirrell cage electric Induction Motor of same make as that of Pump conforming to BIS:9283-1979(Latest with uptosate ammendments) and totally water proof for Submersible duty,isolated from the pump by intermediate casing with double Mechanical seal in oil chamber,grease packed lubricated bearings and provided with stainless steel thrust bearing plate to withstand non-vertical loads with minimum wear and tear. It should also be fitted with a device to take-up expansion of water with the heating of motor including water level guard,erection clamps,cable clips and depth gauge etc. The Pump shall be suitable for operation on data given below including Pump sets (working ), necessary piping and control valves alongwith electrical works including all taxes, insurance, transportation, freight charges, inspection charges, loading, unloading, conveyance to Departmental stores/ site, stacking, etc. including earthing ,specials and wastage etc.; complete as per Tender Specifications, technical data Sheets and instruction of Engineer in charge. including:-

i) Total head in Metres :- 12.31 Metres ii) Discharge required from each pump 26.42 Lps iii) Nos.of Pumps required :-2 No.Pump.(both running) iv) Location : Site is located at a distance of 7 km from Baijnath railway station on Baijnath Utralla Road & 1 km Head Load v) The altitude of place in which :-Altitude of place is 810 Metres above Mean Sea Level. vi) Type of current :-A.C.Three phase supply with frequency 50 cycles per second. vii) Rated Voltage :-415 Vvolts (+/-) 10%treated vii) Rated Voltage :-415 Vvolts (+/-) 10%treated viii) Type of Source: Raw water from Binwa Khad (Pound) viii) Type of Source: Raw water from Binwa Khad (Pound) ix) Characterstics of water :-(a).Temperature = 20oC (b).Turbidity = 6000 PPM upto 50NTU ©. PH = 6.5 to 8.5 (d).Hardness =260Mg/Litre(as CaCo3) (e) TDS 540PPM (g) Total solids____Mg/Litre (h) other ____ (x) Depth of Pound : 2 mtr deep xi) RL of Pump Shaft/Central aixs 810.80 mtr xii) Discharge level of highest point:- 819.00 Metres xiii) Total head in Metres :- 12.31 Metres xiv) Length of Rising Main :- 45.00 Metres xv) Dia of Rising Main :- 250mm dia (MSERW pipe)(L-290 or X-42) xvi) Test Run :- 16.00 Hours continueously for 7 days. xvii) Limits of Pump operator :- (-) 15% (+) 10% of total head. xviii) RPM of pumping set : 2900 RPM Static Head= 8.20 mtr

Supply , Installation, Testing and Commissioning of fully Automatic LT Panel for submersible pump made out of 16 Gauge sheet, powder coated dust and vermin proof, wall/base mounted and front opening door type with copper insulated wiring suitable to operate 2 Nos. pump (2 working ) of the rating offered by the bidder . Starter should be capable enough to handle the following faults like short circuit, over current, under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicators, Power Quality Monitoring & Controlling Relay at the Incomer Feeder, Should be fitted with Surge Suppressor Device suiatble to protect against class-1 & 2 surges.Make: Aarmation Electric Private Lmited/MAS/ELLES/Adlec

Energy Saving Variable Frequency Starter of designed required HP Heavy Duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It Should be capable to monitor & control the frequecy of pumps through out the operation and to maintain the power factor of the system within acceptable limits. It should be able to withstand ambient temperature upto 50 Degrees celcius without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. Make: Aarmation Electric Private Limited/Bechoff/Bosch/Rockwell (As per requirement in Nos.)) (i) Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc. with RS 485 communication Make:- L&T/Conserve/Schnieder/Aarmation (1 No.) (ii) Main incomer MCCB of suitable capacity of L&T / Schnieder/ABB/Siemens make on the coming feeder for pumping set confirming to BIS 2516-1985 ( Latest edition). (1 No.) (iii) LED Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments.(1 Set). (iv) LED On / Off & Trip indicator and push buttons, Control and power wiring,Power capacitor,Cooling fan 230 VAC, Contorl terminal, Bus Bar, i.e.Bolt, insulator, etc. (1 No.) (v) Selector Switch for Auto and Manual Operation (1 No.) (vi) Input Choke of required HP for Energy saving variable frequency Starter which should be installed at the input of Energy saving variable frequency starter, so that there should be proper protection in case of any voltage surge and distortions. (2 Nos.) (vii) Control Transformer Make: Aarmation Electric/MAS/Elle (1 No.) (viii) Power and Control Wiring and Busbar (1 No.) (ix) Installation, Commissioning and Software Development (1 No.) (x) Surge supressor device with Isolating MCCB to eliminate the power surges due to lightening and system surges. (1 No.) (xi) Power quality monitoring & controlling relay with Control Contactor to safeguard the Electronic & Electric elements (1 No.) (xii) Independent Control Panel with Switch Fuse Unit and Fuses of Suitable Amperage to eliminate the KItKat fuses of HPSEB Make: Aarmation/Siemens/Schnieder/L&T (1 Set) (xiii) Mini PLC (Programmable logic controller) with appropriate digital and analog inputs and outputs to give automatic command to Star Delta Starter Panel/ Energy Saving Variable Frequency Starter Panel Make Aarmation Electric/Bechoff Automation/Rockwell Automation (1 No) (xiv) Electronic relay card 8 channel (1 No.) (xv) SMPS 4.5 Amps to energise PLC system (1 No.) (xvi) HMI (Human Machine Interface) 7" display for Monitoring and Controlling of Centrifugal pumps Make: Aarmation Electric/Bechoff Automation/Roackwell (1 no.) (xvii) Control MCB for Automation System (1 No.) (xviii) IOT based system and Mobile App for 3 Users to give command for ON and OFF to Motor remotely and also It should give tripping indication and fault history about the motor tripping due to faults. (1 No.) (xix) Cloud gateway to cloud the data, so that it can be monitored and controlled remotely through Mobile App. (1 job) (xx) Installation, Commissioning and Software Development complete in all respect and as per satisfaction of engineer in charge (1 No.) Including:- (i)

Automation System for Unmanned operation with SCADA feature PLC, HMI, and level Sensor and which includes PLC (Programmable logic controller) with appropriate digital and analog inputs and outputs to give automatic command to Star Delta Starter Panel/ Energy Saving Variable Frequency Starter Panel, Electronic relay card 8 channel, SMPS 4.5 Amps to energise PLC system, HMI (Human Machine Interface) 7" display for Monitoring and Controlling of Centrifugal pumps make Armation Electric, Bechoff Automation/Rockwell Automation, Control MCB for Automation System, Level Sensor to indicate the water level, Shielded Data Cable, Mobile App (Android/IOS) with User ID and Password to monitor and control the pumping operation from Mobile for 3 users., Cloud GateWay for Data Clouding to Server, SCADA software to be installed in Laptop/PC to remotely monitor and control the operation of pumps and also to analysis the pump start and stop history logging, fault status, fault history, Power Quality Parameters like PF, Current, Voltage, KWH, THD etc and Software DevelopMake: Aarmation Electric / Beckhoff Automation(Germany) / Allen Bredley, Cloud space for data storage at cloud /server, Installation and commissioning and software development

Supply & fixing of Kirloskar/Leader make Cast iron double flanged sluice valve heavy size PN 1.6 having by pass arrangement (to be provided on delivery side of size one size higher than delivery size of pump and shall be suitable for withsatanding seat pressure of 10.20kg/cm2 confirming to BIS 1868-API-600 latest edition complete in all respect with in all leads & lifts as per directions and to the entire satisfaction of Engineer-In-Charge. (1 No.)

Supply & fixing of Kirloskar/Leader make Cast steel double flanged swing check type reflux valve of PN 1.6 having by pass arrangements and right equal to dia of R/Main ie. 250 mm dia with upto date arrangements for withstanding seat pressure of 10.20kg/cm2 with flanges of table 5 complete in all respect with in all leads & lifts as per directions and to the entire satisfaction of Engineer-In-Charge. (1 No.)

Supply & fixing of Kirloskar/Leader make Cast iron double flanged swing check type reflux valve of Class-PN 1.6 having by pass arrangement (to be provided on delivery side of size one size higher than delivery size of pump and shall be suitable for withsatanding seat pressure of 10.20kg/cm2 confirming to BIS 1868-API-600 latest edition complete in all respect with in all leads & lifts as per directions and to the entire satisfaction of Engineer-In-Charge. (1 No.)

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. (1 No.)

On supply as required for Pumping Machinery= 10 Rmt

On Motor side as required for Pumping Machinery= 150 Rmt

Supply of standard make 100mm dia circular/Square dial pressure gauge of suitable range of Fiebeg/Bourden/Precision make with all accessories such as;stop cock,copper tubing etc.conforming to BIS-3624-1987 latest with uptodate ammendments. (1No.)

Providing and Laying of GI/MSERW pipe of Column Assembly considering as per site requirement and having appropriate size in accordance with the delivery size of pumping set. The pipe shall be confirming to relevant BIS code & capable with standing the field test pressure equal to 1.5 time the operating pressure including all type of fitting such as bend tapper,/reducer rubber gasket sheet 3mm thick ,nuts & bolts as per 1364-1983 and any other fitting as per site requirment. The pipes shall be capable of withstanding 1.5 times the total pressure indicated icomplete in all respect within all leads and lifts as per the entire satisfaction of the Engineer-in-Charge. (10.00 Rmt)

Supply Installation Testing & Commissioning of horizontal spindle, horizontal/radial split casing and suction (backpull out arrangement) single/ double / multistage centrifugal pumps or combination of pumps in /parallel of KSB / Mather & Platt/ Jyoti /Kirloskar /BE /Maxflow/ Beaconweir make conforming to BIS: 1520-1980 (latest with upto date ammendments) read with BIS: 9137-1978 (latest edition) suitable for lifting water of under mentioned charactristics with impellers of bronze/suitable alloy, priming funnels, casing ring & shaft sleeves of bronze/ suitable alloy, shaft of sutable steel grade with cast iron casing coupled directly through a flexible coupling on a common C.I. / Cast steel base plate (base plate to be from the principle manufacturer of pumping set) to slippering/squirrel cage screen protected drip proof electric induction motor of Kirlokar /NGEF/Crompton/Siemen /Jyoti /BHEL /GEC /ABB conforming to BIS: 325-1978 read with BIS: 900-1968 (latest with upto date ammendments) It should include the cost of bearings, nuts & bolts,painting etc. and shall be suitable for operation as per data given below.

i) Discharge required from each pump 26.42 Lps ii) Nos.of Pumps required :-2 No.Pump.(both running) iii) Location : Site is located at a distance of 8 km from Baijnath railway station on Baijnath Utralla Road & 1 km Head Load iv) The altitude of place in which :-Altitude of place is 810 Metres above Mean Sea Level. v) Type of current :-A.C.Three phase supply with frequency 50 cycles per second. vi) Rated Voltage :-415 Vvolts (+/-) 10%treated vii) Rated Voltage 15 Vvolts (+/-) 10%treated viii) Type of water and Source: Clear water RL of Pump Shaft: 817.50 mtr Rl of discharge heigest point= 901.50 mtr Statice Head: 84 Mtr ix)Characterstics of water :-(a).Temperature = 20oC (b).Turbidity = 6000 PPM upto 50NTU ©. PH = 6.5 to 8.5 (d).Hardness =260Mg/Litre(as CaCo3) (e) TDS 610 PPM (g) Total solids____Mg/Litre (h) other ____ x) Nos. of working hours: 16.00 hours xi) Length of Rising Main :- 780.00 Metres xii) Dia of Rising Main :- 250mm dia (MSERW pipe)(L-290 Or X42) xiii) Test Run :- 8.00 Hours continueously for 7 days. xiv) Limits of Pump operator :- (-) 15% (+) 10% of total head. xv) RPM of pumping set : 2900 RPM

Supply , Installation, Testing and Commissioning of fully Automatic LT Panel for submersible pump made out of 16 Gauge sheet, powder coated dust and vermin proof, wall/base mounted and front opening door type with copper insulated wiring suitable to operate 2 Nos. pump (2 working ) of the rating Offered by bidder Starter should be capable enough to handle the following faults like short circuit, over current, under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicators, Power Quality Monitoring & Controlling Relay at the Incomer Feeder, Should be fitted with Surge Suppressor Device suiatble to protect against class-1 & 2 surges.Make: Aarmation Electric Private Lmited/MAS/ELLES/Adlec

Energy Saving Variable Frequency Starter of designed for offered Pumping Machinery Heavy Duty for smooth start and smooth stop of pumps and for the energy conservation in the system. It Should be capable to monitor & control the frequecy of pumps through out the operation and to maintain the power factor of the system within acceptable limits. It should be able to withstand ambient temperature upto 50 Degrees celcius without derating and have conformal coating class 3C2, so that it can work in any harsh environment like moisture etc. Make: Aarmation Electric Private Limited/Bechoff/Bosch/Rockwell (As per requirement in Nos.)) (i) Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc. with RS 485 communication Make:- L&T/Conserve/Schnieder/Aarmation (1 No.) (ii) Main incomer MCCB of suitable capacity of L&T / Schnieder/ABB/Siemens make on the coming feeder for pumping set confirming to BIS 2516-1985 ( Latest edition). (1 No.) (iii) LED Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments.(1 Set). (iv) LED On / Off & Trip indicator and push buttons, Control and power wiring,Power capacitor,Cooling fan 230 VAC, Contorl terminal, Bus Bar, i.e.Bolt, insulator, etc. (1 No.) (v) Selector Switch for Auto and Manual Operation (1 No.) (vi) Input Choke of required HP for Energy saving variable frequency Starter which should be installed at the input of Energy saving variable frequency starter, so that there should be proper protection in case of any voltage surge and distortions. (2 Nos.) (vii) Control Transformer Make: Aarmation Electric/MAS/Elle (1 No.) (viii) Power and Control Wiring and Busbar (1 No.) (ix) Installation, Commissioning and Software Development (1 No.) (x) Surge supressor device with Isolating MCCB to eliminate the power surges due to lightening and system surges. (1 No.) (xi) Power quality monitoring & controlling relay with Control Contactor to safeguard the Electronic & Electric elements (1 No.) (xii) Independent Control Panel with Switch Fuse Unit and Fuses of Suitable Amperage to eliminate the KItKat fuses of HPSEB Make: Aarmation/Siemens/Schnieder/L&T (1 Set) (xiii) Mini PLC (Programmable logic controller) with appropriate digital and analog inputs and outputs to give automatic command to Star Delta Starter Panel/ Energy Saving Variable Frequency Starter Panel Make Aarmation Electric/Bechoff Automation/Rockwell Automation (1 No) (xiv) Electronic relay card 8 channel (1 No.) (xv) SMPS 4.5 Amps to energise PLC system (1 No.) (xvi) HMI (Human Machine Interface) 7" display for Monitoring and Controlling of Centrifugal pumps Make: Aarmation Electric/Bechoff Automation/Roackwell (1 no.) (xvii) Control MCB for Automation System (1 No.) (xviii) IOT based system and Mobile App for 3 Users to give command for ON and OFF to Motor remotely and also It should give tripping indication and fault history about the motor tripping due to faults. (1 No.) (xix) Cloud gateway to cloud the data, so that it can be monitored and controlled remotely through Mobile App. (1 job) (xx) Installation, Commissioning and Software Development complete in all respect and as per satisfaction of engineer in charge (1 No.) Including:-

Automation System for Unmanned operation with SCADA feature PLC, HMI, and level Sensor and which includes PLC (Programmable logic controller) with appropriate digital and analog inputs and outputs to give automatic command to Star Delta Starter Panel/ Energy Saving Variable Frequency Starter Panel, Electronic relay card 8 channel, SMPS 4.5 Amps to energise PLC system, HMI (Human Machine Interface) 7" display for Monitoring and Controlling of Centrifugal pumps make Armation Electric, Bechoff Automation/Rockwell Automation, Control MCB for Automation System, Level Sensor to indicate the water level, Shielded Data Cable, Mobile App (Android/IOS) with User ID and Password to monitor and control the pumping operation from Mobile for 3 users., Cloud GateWay for Data Clouding to Server, SCADA software to be installed in Laptop/PC to remotely monitor and control the operation of pumps and also to analysis the pump start and stop history logging, fault status, fault history, Power Quality Parameters like PF, Current, Voltage, KWH, THD etc and Software DevelopMake: Aarmation Electric / Beckhoff Automation(Germany) / Allen Bredley, Cloud space for data storage at cloud /server, Installation and commissioning and software development

Supply & fixing of Kirloskar/Leader make Cast steel double flanged Sluice valve heavy duty one dia higher than pump size to delivery of Pump Class- ASA-150 confirming to BIS 14846-2000 latest with upto date ammendments complete in all respect with in all leads & lifts as per directions and to the entire satisfaction of Engineer-In-Charge. (The size of valve specified by the Tenderer) (2 Nos.)

Supply & fixing of Kirloskar/Leader make Cast steel double flanged Swing check type Reflex valve of Class- ASA-150 having by pass arrangement (to be provided on delivery side) on size higherthan the delivery size of pump with upto date ammendments complete in all respect with in all leads & lifts as per directions and to the entire satisfaction of Engineer-In-Charge. (The size of valve specified by the Tenderer) (2 Nos.)

Supply & fixing of Kirloskar/Leader make Cast steel double flanged Swing check type Reflex valve of Class- ASA-150 having by pass arrangement equal to dia of Rising Main i.e. 250mm dia ) with upto date ammendments complete in all respect with in all leads & lifts as per directions and to the entire satisfaction of Engineer-In-Charge. (1 Nos.)

Supply & fixing of Kirloskar/Leader make Cast Iron double flanged Sluice valve heavy duty one dia higher to suction of pump of class PN-1.0 capable of wihstanding nominal seat pressure of 10.20kg/cm2 with upto date ammendments complete in all respect with in all leads & lifts as per directions and to the entire satisfaction of Engineer-In-Charge. (2 Nos.)

Providing & laying PVC insulated jointless, flat water proof copper cable of Siemens/Finolex/ Grandlay/ Gloster make conforming to BIS:1554 (Part I) -1988 or latest with up to date ammendments of suitable size for the pump sets offered(one cable carrying all three phases) including all other electrical equipment /accessories such as thimbles ,flexible pipe, solder, nuts & bolts cable glands etc. laid in pipes or trenches under floor. The type,size & make will be subject to approval of HPSEB authorities.In case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer free of cost. (i) On supply as required for Pumping Machinery= 10 mtr. (ii) On Motor as required for Pumping Machinery= 20 mtr.

Supply of standard make 100mm dia circular/Square dial pressure gauge of suitable range of Fiebeg/Bourden/Precision make with all accessories such as;stop cock,copper tubing etc.conforming to BIS-3624-1987 latest with uptodate ammendments. (1No.)

Providing and Laying of GI/MSERW pipe of Column Assembly (Common Header) considering as per site requirement and having appropriate size in accordance with the delivery size of pumping set. The pipe shall be confirming to relevant BIS code & capable with standing the field test pressure equal to 1.5 time the operating pressure including all type of fitting such as bend tapper,/reducer rubber gasket sheet 3mm thick ,nuts & bolts as per 1364-1983 and any other fitting as per site requirment. The pipes shall be capable of withstanding 1.5 times the total pressure indicated icomplete in all respect within all leads and lifts as per the entire satisfaction of the Engineer-in-Charge. (i) Suction Side…………mm dia one dia higher to suction = 10 mtr (ii) Delivery Side…………mm dia one dia higher to delivery of Pump = 15 mtr (iii) Column assembly 250mm dia- 10 mtr

Providing and lying double loop earthing with coper plate 600x600 x3 thick electrode and copper strip of 25x3 complete including providing of material such as charcoal, common salt, GI pipes, thimbles, nuts & bolts, digging of pits, Copper /GI wire/ Strips of required capacity conforming to BIS 8034-1978 latest with upto date ammendments for above motors and other electrical equipments.

Erection of all equipments including cost of tees, bends,tapers and any other fittings required as per conditions and as per directions of the Engineer-in-Charge.(both Pumping Machinery)

Providing, Laying, Jointing & Testing of HDPE pipe of following dia and grade having suitable pressure polythene pipes high density confirming to I.S. 4984-2016 ( PE 80- Grade ) complete with special flange compression type fittings including all necessary fitting & bends complete in all respect within all leads & lifts to the entire satisfaction of Engineer in Charge. (Earth work in trenches to be measured and paid for separately

90 mm Dia HDPE Pipe PN-6

110 mm Dia HDPE Pipe PN-4

140 mm Dia HDPE Pipe PN-4

160 mm Dia HDPE Pipe PN-4

Providing & Fixing of Cast Iron Alfa Valve of following dia complete in all respect complete in all respect within all leads & lifts to the entire satisfaction of Engineer in Charge. (Earth work in trenches to be measured and paid for separately

90 mm Dia

110 mm Dia

140 mm Dia

160 mm Dia

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. (Group C)

Providing Wiring for light power plug with 2x1.5 mm2 PVC insulted heat resistant flame retardant (HRFC) and low smoke single core (flexible) copper conductor in surface /recessed PVC Conduit alongwith 1 Nos. 1.50 mm2 HRFLRS/PVC insulated single core copper conductor cable as required within all leads and lifts to the satisfcation of Engineer in Charge (Group C ) 3Pin 5/6 amp plug point with 1 Sq. mm PVC insulated coppoer conductor cable for earthing as required.

Supplying and fixing metal box of 200mmx150mmx75mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 3 pin 15 amps socket outlet and 15/16 amps, P/F piano type switch, connections, painting etc. as required.

Wiring for Circut /Sub Main with 2x1.5 mm2 PVC insulted heat resistant flame retardant (HRFC) and low smoke single core (flexible) copper conductor in surface /recessed PVC Conduit alongwith 1 Nos. HRFLRS/PVC insulated single core copper conductor cable as required within all leads and lifts to the satisfcation of Engineer in Charge.

Providing Wiring for power plug with 2x4 mm2 PVC insulted heat resistant flame retardant (HRFC) and low smoke single core (flexible) copper conductor in surface /recessed PVC Conduit alongwith 2 Nos.4mm sq. HRFLRS/PVC insulated single core copper conductor cable as required within all leads and lifts to the satisfcation of Engineer in Charge.

Wiring for Circut /Sub Main with 2x6 mm2 PVC insulted heat resistant flame retardant (HRFC) and low smoke single core (flexible) copper conductor in surface /recessed PVC Conduit alongwith 1 Nos. HRFLRS/PVC insulated single core copper conductor cable as required within all leads and lifts to the satisfcation of Engineer in Charge.

Providing, installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc.as required : Ceiling Fan 1200mm sweep, Category-A.

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required : Single pole Cat-A.

Supplying and fixing 40Amp rating, double pole (Single pole and neutral) 240 volts RCCB having sensitivity current upto 300amp existing MCB DB complete with connections, testing and commissioning etc.as required.

Providing,Installation , Testing & commissioning of shock proof Slim decorative extrude fixture with domestic electronics balast suitable for 36 watt FTL (T8) complete with accessories (excluding t-8 tube) connections as required (1x36 watt Cat.-A).

Providing,Installation, Testing & commissioning of CFL Bulb (9 watt) of reputed make complete in all respect.

Supplying and installation of Sodium vapour light 250watt i/c 900 bend 40mm dia GI pipe (L) class complete in all respects with in all leads & lifts as per directions of Engineer-in-charge.

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (MG) including fitting and clamps including making good the wall ceiling and floor complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge

15mm dia

Providing and placing (at all heights) polyethylene water Storage Tank IS 12701 marked indicating the BIS License no. with cover & suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes including all fittings and float valve excluding the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license ]. 300 Ltrs. capacity

Providing and fixing plastic seat and cover for wash down water closet with C.P. brass hinges and rubber buffers: White plastic seat and cover, solid type.

Providing and fixing vitreous china wash basin with single hole for pillar tap with CI or MS brackets painted white i/c cutting holes & making good the same but excluding fitting i.e. size 400 x 300 mm

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete 10 litre capacity-White

Providing and fixing PVC/G.I. inlet connection for flush pipe connecting with W.C. pan.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve of standard design and of approved make, 15mm nominal bore.

Providing and fixing C.P. Pillar cock with capstan head of approved brand complete in all respect.

Providing and fixing PVC connection pipe of approved brand complete in all respect.

Providing and fixing C.P. water jet including connection pipe with check nut complete in all respect

Providing and fixing PVC pipes of 10 Kg f/Sq.cm working pressure including fittings as per requirement at site complete in all respect in all leads and lifts and to the entire satisfaction of Engineer-in-charge 110 mm OD