Dr Yashwant Singh Parmar University Of Horticulture And Forestry Tender

Providing and fixing PVC floor trap with grating ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Vectus / D-Plast make).

a) 110mmx75mm

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make). a) 75mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make). a) 75mm dia

Providing and fixing PVC plain bend ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).a) 75mm dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawl plugs etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).

a) 75mm dia

Providing and fixing P.V.C. waste pipe 32mm dia for wash basin and sink complete in all respect as satisfaction of Engineer- in-charge.

Supplying and installation of SEAT / BACK: The seat sub-assembly should be made up of 1.2±0.1cm thk Plywood upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The seat can tip-up when not in use and thshould be feature can be used while stacking the chairs horizontally The back sub-assembly should be made up of injection-moulded polypropylene inner upholstered with moulded foam and polyester fabric and covered with an injection-moulded polypropylene outer cover. The contoured back with width extension at the bottom should be a should be designed to give comfort to lower back. The back flexing features allows the back to tilt by 9c±2' to aid the user in adopting a comfortable reclining posture. Both these sub-assemblies should be fixed to the tubular structure, BACK SIZE: 45.2cm (W) X 44.6cm (H) SEAT SIZE: 47.0cm (W) X 50.0cm (D).

2) TUBULAR FRAME STRUCTURE: The powder-coated 4 leg structure should be made of 2.2 ±0.03cm dia x 0.25 ±0.02cm thk M.S. E.R.W. Tube front and rear leg welded along with connecting tube made of 1.9 ±-0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube to form the tubular frame assembly. The legs should be provided with injection-moulded adopter bush in black Nylon and brake-loaded castors enabling easy maneuvering while not in use and stable sitting while in use_ The chairs can be stacked horizontally when not in use_

3) POLYURETHANE FOAM: The Polyurethane foam should be moulded with density = 70.0 ±8.0 kg/m3 and Hardness = 20 ±2 for Seat & 16 ±2 For Back At 25% compression.

4) ARMRESTS: The armrest structure should be made up of 2.2 ±0.03crn dia x 0.25 ±0.02cm thk M.S. E R.W. Tube welded to the Tubular Frame structure and having a scratch-resistant tant ABS Arm top.

5) FULL DESKLET: The Full Desklet assembly should be Flip-up type and should be made up of extension tube of 1.9 ±0.02em dia x 0_2 ±0.016cm thk PAS. E.R.W. Tube and a support tube on L.H. side of 1.6 ±0.02cm dia x 0.2 ±0.016cm thk M.S. E.R.W. Tube on which an scratch resistant tant ABS desklet top should be fixed and covered on bottom side with a bottom cover.

6) BRAKE-LOADED CASTORS : The brake-loaded castors should be assembled to the chair legs, to give a free movement for maneuvering the chair when not in use and it will brake the movement when load should be applied (while in use) to give a stable feel. The twin wheel castors should be injection molded in black Polypropylene. Overall Dimensions Of Chair Seat Height - 47.5 cm. Height – 89.0cm. Width & Depth of Chair as measured from base - Width-71.0cm and Depth-82.0 cm etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Rock worth / Steel Case/ HNI / Kewaunee make).

Supplying and installation of Work - 5026 size shall be 1500 Width x 750 Depth x 740 Height . The top shall be made from 25 mm thick pre- laminated board. All the edges are sealed with 2 mm thick PVC edge band all around . Side panels shall be made from 25 mm thick pre- laminated paticle board . All the edges are sealed with 2 mm thick PVC edge band on the user side and 0.8 mm on the top and bottom side .The side panels have 2 glide screws each for levelling of the desk. Modesty panel shall be made from 18 mm thick pre- laminated particle board . All the edges are sealed with 0.8 mm thick PVC edge band all around. Freestanding Pedestal shall be made from 18 mm pre- laminated particle board with a combination of 2 mm and 0.8 mm PVC edge band on all the exposed surfaces as per requirement. The drawers are provided with suitable slides for smooth operation. All the pedestal drawers are centrally locked with a single key etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Rock worth / Steel Case/ HNI / Kewaunee make).

Supplying and installation of cushioned seat assembly consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretch knitted polyester fabric. Full Back Size : 45.5 cm. (W) x 53.0 cm. (H) *Seat Size :48.5 cm. (W) x 47.0 cm. (D) The HR polyurethane foam used in seat and back cushion is moulded in Density 45±2 kg/m3, and hardness load 16 ± 2 kgf as per 15:7888 for 25% compression. The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. The "5" shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass-filled Poly-am)de form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which is inbuilt in seat base and the tension (return force) is user weight dependent. The assembly consists of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide. The height adjustment feature is button operated having adjustment of 6.6±0.5cm. The Armrest Top is made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide.

The seating height can be adjusted with a pneumatic gas-lift having an adjustment stroke of 9.2 ± 0.3 cm The pedestal is injection moulded in glass-filled Poly-amide and fitted with 5 nos. in wheel castors. The pedestal is 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors. twin wheel castors are injection moulded in Poly-amide having 5.0±0.1cm heel diameter and assembled to the pedestal.The powder coated (DFT 40-60 micron) tubular frame is cantilever type & lade of 02.54±0.03 cm x 0.3±0.016 cm thk MS ERW tube. Shoes are made of glass-filled Poly-amide and fixed the tubular frame. Dimensions measured out to out extreme point) on components in knockdown condition, variations within ±1.0 cm. (W)76(D)76*(H)99.5-108.8cm seat(H)44.5-53.8cm etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Rock worth / Steel Case/ HNI / Kewaunee make).

Supplying and installation of SEAT/BACK ASSEMBLY: The seat & back is made up of 1.2 ± 0.1cm thk. hot pressed plywood measured as per QA method described in OCP-QLTA-PL14-18 ; upholstered with synthetic leather over moulded High Resilience Polyurethane foam. MID BACK SIZE: 51.6 cm. (W) x 65.7 cm. (H) Fixed Armrest Top is PU moulded over metal insert. * SEAT SIZE: 49.0 cm. (W) x 51.4 cm. (D). TUBULAR VISITOR FRAME (Visitor Chair): The tubular frame is powder coated (DFT 40-60 microns) cantilever structure & made of Dia.Ø 2.54 ±0.03cm. x 0.2 ±0.016cm.thk. M.S. E.R.W. Tube with a connecting M.S. Spine welded to it. Back spine is fitted to the frame assembly. Fixed Armrest Top is PU moulded over metal insert etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Rock worth / Steel Case/ HNI / Kewaunee make).

Supplying and installation of Material: Top 18 mm Melamine laminated Particle Board & rest 15 mm Paper laminated Particle board. Hardware: Screw, KD Fittings, Slides & Castors. Construction: Knock down .Load Bearing Capacity: 30 Kgs. Packets: 1 No. Finish: Melamine laminated Top & rest Paper lamination (Color: Honey).Dimensions: W 900 X D 500 X H 750 etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Rock worth / Steel Case/ HNI / Kewaunee make).

Supplying and installation of Research module Laboratory Units (Waldner / Kotterman / Godrej make) with work surface of following size with V-groove type moulding jet black Granite 20mm + - mm thick as per layout along with neoprene strip 2.5” width and 6mm thick SR 998 glue for neoprene mat complete in all respect as per satisfaction of Engineer-in-charge as well as concerned deptt. The following size of storage unit and other articles of module labs. are as under: Storage unit with Cam lock : 750mm Depth, 880mm Ht with metal shutter AT-600W-750D-9H 1 No. AT-1500W-750D-9H 1 No. AT-1250W-750D-9H 2 Nos. UBC-600W-450D-674H-2S-1D 4 Nos. UBC-450W-450D-674H-1S-RH 1 No. UBC-450W-450D-674H-1S-LH 1 No. LS-600W-9H 2 Nos. GODREJ-UV-CASE 2 Nos. RP-750D-9H 2 Nos. CT-DOOR -FR 1 No. CT-750D-9H 1 No. TRUNKING 4 Nos. SIDE PANELS FOR SINK UNIT 1 No. 3 WAY WATER FAUCET BENCH MOUNTED 8" SWING 1 No. PP DROP -IN-SINK 560X355MM 1 No. 6/16A 6 PIN SHUTTER SOCKET MODEL M1332 8 Nos. 16A 1 WAY SWITCH MODEL M0130 and looping with your old wiring as per layout 8 Nos.

Supplying and installation of Research module Laboratory Units (Waldner / Kotterman / Godrej make) with work surface of following size with V-groove type moulding jet black Granite 20mm + - mm thick as per layout along with neoprene strip 2.5” width and 6mm thick SR 998 glue for neoprene mat complete in all respect as per satisfaction of Engineer-in-charge as well as concerned deptt. The following size of storage unit and other articles of module labs. are as under AT-450W-750D-9H 1 No. AT-1200W-750D-9H 6 Nos .AT-1050W-750D-9H 1 No. UBC-600W-450D-674H-2S-1D 9 Nos. UBC-450W-450D-674H-1S-RH 1 No. UBC-450W-450D-674H-1S-LH 2 Nos. LS-600W-9H 4 Nos.RP-750D-9H 2 Nos. CT-750D-9H 1 No.TRUNKING 6 Nos. SIDE PANELS FOR SINK UNIT 2 No. DOOR FRAME FOR INLINE SINK UNIT 2 Nos. 3 WAY WATER FAUCET BENCH MOUNTED 8" SWING 2 Nos. PP DROP -IN-SINK 560X355MM 2 Nos. 6/16A 6 PIN SHUTTER SOCKET MODEL M1332 12 Nos. 16A 1 WAY SWITCH MODEL M0130 and looping with your old wiring as per layout 12 Nos.

Supplying and installation of Research module Laboratory Units (Waldner / Kotterman / Godrej make) with work surface of following size with V-groove type moulding jet black Granite 20mm + - mm thick as per layout along with neoprene strip 2.5” width and 6mm thick SR 998 glue for neoprene mat complete in all respect as per satisfaction of Engineer-in-charge as well as concerned deptt. The following size of storage unit and other articles of module labs. are as under Storage unit with Cam lock : 750mm Depth, 880mm Ht with metal shutter AT-600W-750D-9H 1 No. AT-1500W-750D-9H 1 No. AT-1200W-750D-9H 3 Nos. AT-1050W-750D-9H 1 No. UBC-600W-450D-674H-2S 6 Nos. UBC-450W-450D-674H-1S-RH 1 No. UBC-450W-450D-674H-1S-LH 3 Nos. LS-600W-9H 3 Nos.RP-750D-9H 2 Nos. CT-750D-9H 1 No.TRUNKING 5 Nos. SIDE PANELS FOR SINK UNIT 2 Nos. DOOR FRAME FOR INLINE SINK UNIT 1 No. 3 WAY WATER FAUCET BENCH MOUNTED 8" SWING 1 No. PP DROP -IN-SINK 560X355MM 1 No. 6/16A 6 PIN SHUTTER SOCKET MODEL M1332 10 Nos. 16A 1 WAY SWITCH MODEL M0130 and looping with your old wiring as per layout. 10 Nos.

Supplying and installation of Research module Laboratory Units (Waldner / Kotterman / Godrej make) with work surface of following size with V-groove type moulding jet black Granite 20mm + - mm thick as per layout along with neoprene strip 2.5” width and 6mm thick SR 998 glue for neoprene mat complete in all respect as per satisfaction of Engineer-in-charge as well as concerned deptt. The following size of storage unit and other articles of module labs. are as under Storage unit with Cam lock : 750mm Depth, 880mm Ht with metal shutter MT-1200W-750D-9H 1 No. AT-600W-750D-9H 1 No. UBC-600W-450D-674H-2S-1D 3 Nos. RP-750D-9H 2 Nos. TRUNKING 2 Nos. SIDE PANELS FOR SINK UNIT 1 No. DOOR FRAME FOR INLINE SINK UNIT 1 No. 3 WAY WATER FAUCET BENCH MOUNTED 8" SWING 1 No. PP DROP -IN-SINK 560X355MM 1 No. 6/16A 6 PIN SHUTTER SOCKET MODEL M1332 4 Nos. 16A 1 WAY SWITCH MODEL M0130 and looping with your old wireing 4 Nos. ROOM-2MT-1200W-750D-9H 1 No. AT-600W-750D-9H 1 No. UBC-600W-450D-674H-2S-1D 3 Nos. RP-750D-9H 2 Nos. TRUNKING 2 Nos. SIDE PANELS FOR SINK UNIT 1 No. DOOR FRAME FOR INLINE SINK UNIT 1 No. 3 WAY WATER FAUCET BENCH MOUNTED 8" SWING 1 No. PP DROP -IN-SINK 560X355MM 1 No. 6/16A 6 PIN SHUTTER SOCKET MODEL M1332 4 Nos. 16A 1 WAY SWITCH MODEL M0130 and looping with your old wireing as per layout 4 Nos.