Dr Yashwant Singh Parmar University Of Horticulture And Forestry Tender

Centering and shuttering including strutting, propping etc. and removal of form for etc. complete in all respect as per satisfaction of Engineer-in-charge.

a). Foundations, footings, bases of columns etc for mass concrete

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement work up to plinth level with 1.1.5:3 (one cement : one and half sand : three stone aggregate 20 mm (Twenty milimetre) nominal size) in foundation and plinth etc. Complete in all respect as per satisfaction of Engineer-in-charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Cold twisted bars.

Providing and fixing mild steel round holding down with bolts, plates and washers etc complete in all respect as per satisfaction of Engineer-in-Charge

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Applying priming coat with ready mixed red oxide zinc chromate primer of approved brand and manufacturer on steel galvanized iron/ steel works etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Painting with aluminium paint of approved brand and manufacturer to give an even shade etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). Two or more coats on new work

15 mm (fifteen milimetre thick) cement plaster on rough side of single or half brick wall of mix with cement mortar 1:4 (one cement: four sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Finishing walls with Acrylic Smooth exterior paint of required shade with New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Supplying and drawing 4 Sqmm of PVC insulated, heat resistant, flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface / recessed, Steel/PVC conduit as required complete in all respect as per satisfaction of Engineer-in-charge.

a). 6 x 4.0 Sq. mm.

b.) 5 x 4.0 Sq. mm

Supplying and erection of wall mounted metal boards for switch gear mounting of suitable size, with permissible variation in size of plus minus 5mm, welded frame work made of M.S. angle iron 50mm x 50mm x 6mm thick duly welded complete with 3mm thick M.S. sheet fixed with hinges as open able front, complete with locking arrangement including painting and bonding to the existing earth as required complete in all respect as per satisfaction of Engineer-in-charge.

Supplying and erection of following depth sheet metal cubical pedestal of suitable dimensions with plus-minus 5 cm variation made from (50 mm x 50 mm x 6 mm thick) M.S. angle iron frame, covered with 1.6 mm thick M.S. sheet duly welded on five sides & front side hinged, complete with locking arrangement with sufficient No. vertical and horizontal intermediate switchgear supporting members each of M.S. flat 50mmx6mm thick of suitable length duly welded. The cubical pedestal shall have cable entry box at one or two sides and 4 No. legs of 50mmx50mmx6mm thick M.S. angle iron each 60 cm long including, powder coated painting and bonding to the existing earth etc., the same shall be erected in the 1:2:4 cement concrete plat-form of suitable dimensions 15 cm high from ground level and 45 cm thick. The cubical pedestal shall be 15 cm from the top of cement concrete plat-form complete in all respect as per satisfaction of Engineer-in-charge. a). 300mm deep (Nominal).

Supplying & fixing sheet metal bus-bar chamber suitable for 63 amp. 415 volts capacity with 4 Nos. copper strip bus-bars each of length 300mm & cross-sectional area (16mmx3.17mm), enclosure made from 1.6mm thick M.S. sheet having overall dimensions (530mmx350mmx150mm) nominal with all accessories including connections, earthing the body etc. as required complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing following rating and breaking capacity MCCB four pole in the existing cubical panel board including drilling holes in the cubicle panel, making connections, etc. as required complete in all respect as per satisfaction of Engineer-in-charge. (L&T/ Havells Make)

a). 100 Amp. – 10 KA

b). 100 Amp. – 16 KA

Supplying & erection of 6 amps. to 32 amps. rating, 10KA breaking capacity, 240 volts, ‘C’ curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a) Single pole. Category – A

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a) 40 Amps. Cat-A.

Supplying and fixing of following way triple pole and neutral sheet steel MCB distribution board, 415 volts, on surface / recess, with provision for 4-pole MCB / isolator / RCCB / RCBO as incomer and SP MCBs as outgoing, complete with tinned copper bus-bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a) Single door-4 way (8+12), horizontal type.

Earthing with GI earth plate 600mmx600mmx6mm thick, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but with charcoal or coke and salt) complete as required as per direction of Engineer-in-charge.

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required complete in all respect as per satisfaction of Engineer-in-charge.

Supplying and laying 6 SWG G.I. wire at 0.50 metre. below ground level for earth electrode conductor, including soldering etc. as required complete in all respect as per satisfaction of Engineer-in-charge.

Providing and laying of one No. aluminium conductor, PVC insulated and PVC sheathed, armoured / XLPE power cable, working voltage 1100 volts grade direct in ground to be laid 1 meter below the ground level including excavation sand cushioning, protective covering and refilling the trench etc. of the required size complete in all respect as per satisfaction of Engineer-in-charge.a). Armoured cable 16Sqmm (four core).

Providing and Erection of Octagonal MS pipe high mast pole along with base material and hydraulic power pack 2Kw single phase induction motor (Crompton/ KSB/ Kirlosker make) with allied accessories as required etc. complete in all respect as per satisfaction of Engineer-in-charge .a). Overall length 15.25 metre, with outer dia and thickness of section in bottom 304.80 mm into 6mm and Top 165.10mm into 4.5 mm depth with app. Weight 520 Kg with base material

Supplying, installation, testing and commissioning of flood LED light fitting 350 watts made up of pressure die-cast aluminium housing with toughened glass high power LEDs and secondary lenses with IP66 protection, efficacy 120 lm/w etc. complete in all respect as per satisfaction of engineer-in-charge. (Wipro/ Phillips/ Bajaj/Jaguar & Great white maket).

Supplying, installation, testing and commissioning of Integral Aviation LED light fitting comprising of aluminium housing with polycarbonate enclosure etc. complete in all respect as per satisfaction of engineer-in-charge. (Wipro/ Phillips/ Bajaj/Jaguar & Great white maket).