Dr Yashwant Singh Parmar University Of Horticulture And Forestry Tender

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) 25mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Single tee with door 75x75x75 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5° 75 mm bend

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar

Dismantling doors, windows and clerestory windows shutter including chowkhats, architrave, holdfasts etc. complete and stacking within all lead : Of area 3 sq. metres and below

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 75 mm dia

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931: 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and installation of staff chair complete in all respect. SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression. The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with spacer fabric and leatherette. Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D), BACK SIZE: 45 cm. (W) x 75.5 cm (D). ARMRESTS The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk MS E.R.W tube. The armrest height adjustable up to 6.5±0.5cm in 5 steps.The Armrest structure should be powder coated (DFT 40-60 micron). ACTIVE BIO-SYNCHRO mechanism (FU3401/3402): The adjustable tilting mechanism should be designed with the following features: 360° revolving type, Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating position, 5-position Tilt limiter giving option of variable tilt angle to the chair, Seat/back tilting ratio of 1: 2, The mechanism housing should be made up of HPDC Aluminum black powder coated. SEAT DEPTH ADJUSTMENT Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. TWIN WHEEL CASTOR : 5 Nos. twin wheel castors should be injection moulded in plastic having 6.0±0.1cm wheel Diameter and assembled to pedestal etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Steel case / Haworth / Spacewood make)

Providing and installion of Vistor Chair. SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3, and hardness load 16 ± 2 kgf for 25% compression. The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with spacer fabric and leatherette. SeatSIZE:47.0cm(.W)x48.0cm.(D)BACK SIZE : 45 cm. (W) x 60.5 cm. (D) .Visitor Tubular Frame The powder coated (DFT 40-60 micron) tubular frame should be cantilever type & made of 02.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. The back connected to frame through powder coated (DFT 40-60 micron) high pressure die cast connector piece etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Steel case / Haworth / Spacewood make).

Supplying, installation, testing and commissioning of temperature controlled Colony initiation & brood rearing room of size 5700mmx4380mmx2600mm with details & specifications as below including all accessories:- 1. Room temperature: 25Deg.c - 30Deg.C (Ambient Temp 40Deg.c) 2. Relative Humidity (RH): 50% - 70% 3. Insulation on Wall & Ceiling: 105 mm PUF panels (Climatrol/ Desmond/ King Span Make) with ceiling panels to panels interconnection for the male-female Cam lock for joint finished with 0.5mm SS-304 fiishing in exposed area, PPGI for unexposed area 4. Insulation on Floor: PUF panels finished bitumen sheet KOTA stone (Kotastone flooring to be paid extra) 5. Doors: 1 No. Flush type door 34" x 78" for the airtight sealed arrangement with kickplate, door closer, hinge etc. 6. Condensing Unit: 02 Nos. with cooling capacity of 15,000 BTU/hr (Condensing temp: 50 Deg. C) 7. Compressor: 1 No. (Emerson/Frascold/Hermatic Make) 8. Air Flow: Controlled & guided flow of air through condesnig coil 9. Evaporators: 02 Nos. with Noise level not more than 20 dB, cooling capacity of 15,000 BTU/hr, air circulation through guided air flow with eco-friendly Refrigerant 10. Lightning: Provision of red light having intensity of 60 Hz. 11. De-Humidifier: 1 No. (Subzero/Bryair/HoneyWell Make) 12. Humidifier: 5 Kg Ultrasonic Automatic type with controller and RH display -1Nos. 13. RO: 1 No. for supply to humidifier with accessories 14. Accessories: Strip curtains, temp controller, controller box, RH controller etc. 15. Hanging Arrangements: Grooves & Trapes to provide Hanging Arrangements 16. Refrigerant: 1 No. (Ecofriendly )

Supplying, installation, testing and commissioning of temperature controlled Gynes & Drones maintenance room of size 3000mm x 4400mm x 2600mm with details & specifications as below including all accessories:- 1. Room temperature: 20Deg.c - 30Deg.C (Ambient Temp 40Deg.c) 2. Relative Humidity (RH): 50% - 70% 3. Insulation on Wall & Ceiling: 105 mm PUF panels (Climatrol/ Desmond / King Span Make) with ceiling panels to panels interconnection for the male-female Cam lock for joint finished with 0.5mm SS-304 fiishing in exposed area, PPGI for unexposed area 4. Insulation on Floor: PUF panels finished bitumen sheet KOTA stone (Kotastone flooring to be paid extra) 5. Partition: 105mm SS-304 PUF panels wall for partition of size 3000mm x 2600mm dividing the room into two equal parts. 6. Doors: 2 Nos. Flush type door 34" x 78" for the airtight sealed arrangement with kickplate, door closer, hinge etc. 7. Condensing Unit: 04 Nos. with cooling capacity of 15,000 BTU/hr (Condensing temp: 54 Deg. C) 8. Compressor: 1 No. (Emerson/Frascold/Hermatic Make) 9. Air Flow: Controlled & guided flow of air through condesnig coil 10. Evaporators: 04 Nos. with Noise level not more than 20 dB, cooling capacity of 15,000 BTU/hr, air circulation through guided air flow with eco-friendly Refrigerant 11. Lightning: Provision of red light having intensity of 60 Hz. 12. De-Humidifier: 2 Nos. (Subzero/Bryair/HoneyWell Make) 13.Accessories: Strip curtains, temp controller, controller box, RH controller etc. 14. Hanging Arrangements: Grooves & Trapes to provide Hanging Arrangements 15. Refrigerant: 1 No. (Ecofriendly )

Supplying, installation, testing and commissioning of temperature controlled Cool Room/ Hibernation Room of size 2800mm x 4350mm x 2600mm with details & specifications as below including all accessories:- 1. Room temperature: 0-5 Deg C (Ambient Temp 40Deg.c) 2. Relative Humidity (RH): 70% - 90% 3. Insulation on Wall & Ceiling: 105 mm PUF panels (Climatrol/ Desmond / King Span Make) with ceiling panels to panels interconnection for the male-female Cam lock for joint finished with 0.5mm SS-304 fiishing in exposed area, PPGI for unexposed area 4. Insulation on Floor: PUF panels finished bitumen sheet KOTA stone (Kotastone flooring to be paid extra) 5. Doors: 1 No. Flush type door 34" x 78" for the airtight sealed arrangement with kickplate, door closer, hinge etc. 6. Condensing Unit: 02 Nos. with cooling capacity of 15,000 BTU/hr (Condensing temp: 54 Deg. C) 7. Compressor: 1 No. (Emerson/Frascold/Hermatic make) 8. Air Flow: Controlled & guided flow of air through condesnig coil 9. Evaporators: 02 Nos. with Noise level not more than 20 dB, cooling capacity of 15,000 BTU/hr, air circulation through guided air flow with eco-friendly Refrigerant 10. Lightning: Provision of red light having intensity of 60 Hz. 11. Humidifier: 5 Kg Ultrasonic Automatic type with controller and RH display -1 No. 12. RO: 1 No. for supply to humidifier with accessories 13. Accessories: Strip curtains, temp controller, controller box, RH controller etc. 14. Hanging Arrangements: Grooves & Trapes to provide Hanging Arrangements 15. Refrigerant: 1 No. (Ecofriendly )

Supply of 400 KVA, 11/0.433kv, Copper Wound, Distribution Transformer, EEL-2 as per IS Specifications including accessories with 3 years Warrnatyas per satisfaction of Engineer-In charge. (Kirloskar/Greaves/GTB/EVR Make)