Dr Yashwant Singh Parmar University Of Horticulture And Forestry Tender

b). 1:2:4 (one cement: two sand): four graded stone aggregate 20 mm (twenty milimetre) nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for etc. complete in all respect as per satisfaction of Engineer-in-charge.

a)Foundations, footings, bases of columns, etc. for mass concrete

b)Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, fnishing and reinforcement work up to plinth level with 1.1.5:3 (one cement : one and half sand : three stone aggregate 20 mm (Twenty milimetre) nominal size) in foundation and plinth etc. complete in all respect as per satisfaction of Engineer-in-charge.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to all floor level with 1.1.5:3 (one cement : one and half sand : three stone aggregate 20 mm (Twenty milimetre) nominal size) in foundation and plinth etc. complete in all respect as per satisfaction of Engineer-in-charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level etc. complete in all respect as per satisfaction of Engineer-in-Charge. a) Cold twisted bars.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to all floor level with cement mortar 1:4 (one cement : four sand) etc. complete in all respect as per satisfaction of Engineer-in-charge ( Bricks will be supplied by the university free of cost).

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete in all levels etc. complete in all respect as per satisfaction of Engineer-in-Charge. a). Granite of any colour and shade Area of slab upto 0.50 sqm

MS hollow pipe/ Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tappings of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete in all respect as per satisfaction of Engineer-in-Charge.(Tata/ Jindal Make)

Providing and fixing precoated galvanised steel sheet 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete in all respect as per satisfaction of Engineer-in-Charge (Jindal/ Tata make.)

a). Ridges plain (500 - 600mm)

b). Barge board upto 300mm

15 mm (fifteen milimetre thick) cement plaster on rough/ fair side of single or half brick wall of mix with cement mortar 1:4 (one cement: four sand) complete in all respect as per satisfaction of Engineer-in-Charge.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade etc. in all respect as per satisfaction of Engineer-in-Charge..a) One or more coats on old work

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within all leads etc. complete as per direction of Engineer-in-charge. a). In cement mortar

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within all leads etc. all complete as specified and as directed by the Engineer-in-Charge.

Removing mortar from bricks and cleaning bricks including stacking within all lead etc. complete as per direction of Engineer-in-charge. (stacks of cleaned bricks shall be measured).

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extrasand Complete all as per direction of Engineer-in-Charge . a) 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. (NTC Make)

Fixing of ready made MS hollow pipe gate with allied accessories including all leads, lifts and carriage of material complete in all respect.