Dr Yashwant Singh Parmar University Of Horticulture And Forestry Tender

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within all lead : Up to 10 mm thick

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (Nitco/Johnson/Kazaria make 1st quality)

Precast terrazo tiles 22 mm thick with graded marble chips of size upto 12 mm, laid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) : Dark shade pigment using ordinary cement

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement : 4 coarse sand).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) (Jindal/Hindalco make)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) (Jindal/Hindalco make)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness weight not less than 10.00 kg /sqm

With float glass panes of 5.00 mm thickness weight not less than 12.50 kg / sqm

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge. Anodized (AC 15 ) aluminium tubular handle bar

Providing and fixing 100mm brass mortice latch & locks with 6 livers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 300x10 mm

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 100x75x4 mm

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm

Providing and fixing vitreous china dual purpose closet suitable for use as squatting pan or European type water closet (Anglo Indian W.C pan) with seat & lid fixed with C.P. brass hinges and rubber buffers, 10 litre low level flushing cistern with fitting and brackets, 40 mm flush bend, 20 mm over flow pipe, with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: White vitreous china dual purpose WC pan with white solid plastic seat and lid with white vitreous china flushing cistern and C.P. flush bend. (Cera / Hindware make)

Providing and fixing 8mm dia C.P./S.S. jet with flexible tube upto 1m long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. (Cera / Hindware make)

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2" BSP thread and shapes, weighing not less than 60 gms.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps (Cera / Hindware make)

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: White glazed fire clay kitchen sink of size 600x450x 250 mm (Cera / Hindware make)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length 15 mm nominal bore

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : 100 mm dia

Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 20 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 40 mm dia nominal bore

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 20 to 40 mm nominal bore

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing brass stop cock of approved quality 15 mm nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing PTMT grating of approved quality and colour Circular type 100 mm nominal dia

Cutting out cracks of roof terrace to V-section, cleaning out welting, grouting with Cement and Sand Slurry 1:3 (1 Cement : 3 Sand.)

Removing old paint or polish from wood and wood based surfaces with paint remover of approved brands and manufacture and making the surface even with:- Paint remover of approved brand and manufacture :

Providing and fixing recessed roll type toilet paper holder (vitreous China)

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a)110mm dia

b) 75mm dia

Providing and fixing PVC floor trap with grating ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Kisan / D-Plast make). a)110mmx75mm

Providing and fixing PVC plain bend ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make).a) 75mm dia

b) 110mm dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a) a)75mm dia

b) 110mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Kisan/D-plast make). a) 75mm dia

b) 110mm dia

Providing and fixing PVC size P or S trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Kisan / D-Plast make). a) 110mm dia

Providing and fixing C.P. Brass Towel Rail complete with C.P. Brass brackets fixed to wooden plug with C.P. Brass Screws:- 600mmx20mm

Providing and fixing chromium plated brass soap dish with C.P. Brass Brackets fixed to wooden cleats with C.P. Brass Screws.

Providing and fixing zebra roller blinds of superior quality with required accessories complete in all respect as per satisfaction of Engineer-in-Charge (Bizel/Nova/Vista Make).

Providing and installation of Executive table with attached ERU with pedestal  1650 x 1950x 750 Primary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Soft closing access flap with in-build power box are provided on work surface for wire management Secondary Work Surface Made of 25mm thick MDF one side pre-laminate board confirming to IS-4587:1998 with 0.4mm PVC membrane pressed on to top. Modesty Panel Made of 25mm thick MDF one side pre-laminate board confirming to IS- 4587:1998 with 0.4mm PVC membrane pressed on to top. Under structure Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Integrated Pedestal Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top Pedestal construction is BOX-BOX-FILE type which Uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security etc. complete in all respect as per satisfaction of Engineer-in-charge (Steel case / Haworth / Godrej / Spacewood make or equivalent).

Providing and installation of Stool SEAT ASSEMBLY: The seat should be made up of 1.2±0.1cm thick flat plywood and with moulded Polyurethane foam and should be upholstered with replaceable synthetic leathercovers. SEATSIZE:Diameter40.0cm, ADJUSTMENTS:360°RevolvingtypeBack. ASSEMBLY: The back foam should be designed with contoured Lumbar support for extra comfort. The upholstery should be available in synthetic leather. *BACK SIZE: 45.0 cm (W) covered with polyurethane foam, HIGHRESILIENCE(HR)POLYURETHANE OAM:The_HR.polyurethane foam should be _molded with density = 45 +1-2 kg/m3 and Hardness load 16 ± 2 kgf for 25% compression HEIGHT ADJUSTMENT: The manual height adjustment should be very easy to operate with a help of a knob.. It can be easily locked at the most comfortableposition. PEDESTAL ASSEMBLY: The five-prong pedestal should be fabricated from 0.2 ± 0.02 cm: thick HR sheet.( should be :. DD 1079 / HR), powder coated ( DFT 40-60 microns ) and fitted with an injection moulded black Polypropylene Hub Cap and 5 nos. twin wheel castors. The pedestal-should be 55.0±0.5cm pitch-circle-diameter- (65.0±-1,0cm-with-castors).-Circular-foot-ring of 052.0±0.2cm made up of 01.9±0.2 x 0.12±0.0096cm thk MS ERW Tube for foot support in High-base stool. TWIN WHEEL CASTORS: The twin wheel castors should be injection moulded in Black Nylon etc. complete in all respect as per satisfaction of Engineer-in-Charge (Steel case / Haworth / Godrej / Spacewood make or equivalent)

Providing and installation of Executive Chair complete in all respect. Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with leatherette and moulded High Resilience (HR) Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The Seat SIZE: 47.0 cm. (W) x 48.0 cm. (D). The Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette. The BACK SIZE: 47.7 cm. (W) x 76.4 cm. (D). The armrest top should be moulded from polyurethane (PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish. The armrest height adjustable up to 6.5±0.5cm in 5 steps. The adjustable tilting mechanism should be designed with the following features: • 360' revolving type. • Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be operated in seating position. • 5-position Tilt limiter giving option of variable tilt angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing should be made up of HPDC Aluminum black powder coated. Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. The pedestal should be High Pressure Die cast polished Aluminum and fitted with 5 nos. twin wheel castors. The pedestal should be 65.0 ± 0.5cm. Pitch-center dia.(75.0 ± 1.0cm. With castors.) The twin wheel castors should be injection moulded in black PP having 6.0± 0.1cm wheel Diameter etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Steel case / Haworth / Spacewood make or equivalent)

Providing and installation of staff chair complete in all respect. SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression. The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with spacer fabric and leatherette. Seat SIZE : 47.0 cm. (W) x 48.0 cm. (D), BACK SIZE: 45 cm. (W) x 75.5 cm (D). ARMRESTS The armrest top should be moulded from polyurethane(PU) and mounted on to a drop lift adjustable type tubular armrest support made of 03.81±0.03 cm x 0.2±0.01 cm thk MS E.R.W tube. The armrest height adjustable up to 6.5±0.5cm in 5 steps.The Armrest structure should be powder coated (DFT 40-60 micron). ACTIVE BIO-SYNCHRO mechanism (FU3401/3402): The adjustable tilting mechanism should be designed with the following features: 360° revolving type, Front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating position, 5-position Tilt limiter giving option of variable tilt angle to the chair, Seat/back tilting ratio of 1: 2, The mechanism housing should be made up of HPDC Aluminum black powder coated. SEAT DEPTH ADJUSTMENT Seat depth adjustment should be integrated in the seat through a sliding mechanism. Seat depth adjustment range should be of 6.0±0.5 cm. ADJUSTABLE BACK SUPPORT Back Frame should be connected to the Up/Dn mechanism housed in Plastic T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. PNEUMATIC HT. ADJUSTMENT The pneumatic ht adjustment has an adjustment stroke of 10.0±0.3 cm. TWIN WHEEL CASTOR : 5 Nos. twin wheel castors should be injection moulded in plastic having 6.0±0.1cm wheel Diameter and assembled to pedestal etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Steel case / Haworth / Spacewood make or equivalent)

Providing and installion of Vistor Chair. SEAT/BACK ASSEMBLY: The Cushioned seat should be made of Injection molded Plastic outer & inner. Plastic Inner should be upholstered with stitched cover and moulded High Resilience Polyurethane foam of Density 45±2 kg/m3, and hardness load 16 ± 2 kgf for 25% compression. The stitched cover should be made from spacer fabric and leatherette. Cushioned back should be made of PU Foam with insitu molded MS E.R.W Round Tube of size 1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with spacer fabric and leatherette. SeatSIZE:47.0cm(.W)x48.0cm.(D)BACK SIZE : 45 cm. (W) x 60.5 cm. (D) .Visitor Tubular Frame The powder coated (DFT 40-60 micron) tubular frame should be cantilever type & made of 02.54±0.03 cm x 0.2±0.016 cm thk MS ERW tube. The back connected to frame through powder coated (DFT 40-60 micron) high pressure die cast connector piece etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Steel case / Haworth / Spacewood make or equivalent).

Providing and installation of Desking office table (Steel case/ Haworth/ Godrej/ Space wood make) 1500X750X750mm WITH CREDESTAL 30mm thick Table top made up of 18mm thick Pre-laminated Particle board with 12mm thick thin PVC foil wrapped decorative profile made up of MDF fixed along all the edges from bottom side which provide decorative waterfall edge profile to top with twin color look the decorative trim to be connected at the angle of 45Degree with each other. M.S. T-Hat of 0.8mm thickness is provided for extra support for the Top of length 1200mm and above. LEG: - 25mm thick Leg or Gable End made up of 25mm thick Pre-laminated Particle board with M.S. Leveler bracket to give floating look. Modesty: - Modesty Panel made up of 18mm thick Pre-laminated Particle board providing stability to structure and allows sufficient leg privacy to user. "D" headed Decorative aluminum profile fixed on it, the aluminum profile to be fixed by making grove in panel for better fixing and integrated look. along with 3 dr Pedestal Storage 26 mm thick Melamine top edge band with profile wrapped trim and shutter 18 mm melamine finish type pvc handle silver colour etc. complete in all respect as per satisfaction of Engineer-in-Charge.

Providing and installation of 4 (four) Door Book Case shall have the configuration of 914mm(W)x320mm(D)x1742mm(H). Rigid Knock Down Construction with prime quality CRCA steel Top Back and side are made from 0.7 mm thick CRCA Rest in 0.8 mm CRCA steel with anti rusting treatment. The Top Pannel, Back Pannel and Side Pannel are made from 0.7mm high yield CRCA and other components from 0.8mm CRCA. Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision which shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. Each door should be provided with plastic side end caps as handle which is easy to grip. Each compartment shall have a storage shelf with a UDL capacity of max 80 Kg. The 2 Door Book Case shall have 18mm PLB Top straight edge with PVC lipping. The finishing shall include Epoxy powder coated to the thickness of 50 microns (,/- 10) etc. complete in all respect as per satisfaction of Engineer-in-Charge (Godrej / Steel case / Haworth / Spacewood make or equivalent).

Providing and installation of floor storage unit (Steel case/ Haworth/ Godrej/ Space wood make or equivalent) Overall Dimensions of main Floor Unit 450 W Metal Door shall be 448mm (W) x20mm (T)x1978mm (H) . The construction and Material shall be made from combination of CRCA 0.5 mm & 0.8 mm thickness. Steel Hinged Door with shelf closing hinges .The handle shall be Aesthetically appealing, Ergonomic, Made of Aluminum. The loacking shall be 3 way and Finish shall be Epoxy Powder coated to the thickness of 50 microns and Overall Dimensions of Floor Unit 500 W main shall be 450mm(W)x500mm(D)x2025mm(H) with leveler . The construction shall be aesthetically appealing completely knock down construction. Legs shall be fitted with screw type leveler and material shall be from combination of CRCA 0.5 mm & 0.8 mm thickness. The shelving shall be height wise adjustable shelf mounting, each full shelf shall have a load capacity of 40 kg UDL max. and 4 nos. of full adjustable shelves. A4 size box file (85 W x 285 D x 345 H mm) can be stored vertically on all five loading levels. Finish shall be epoxy powder coated to the thickness of 50 microns (+/-10) etc. complete in all respect as per satisfaction of Engineer-in-charge.

Providing and installation of floor unit (Steel case/Haworth/Godrej/Space wood make or equivalent) Overall Dimensions of Floor Unit Add On 900 W Metal Door shall be 448mm(W)x20mm(T)x1978mm (H) . The construction and Material shall be made from combination of CRCA 0.5 mm & 0.8 mm thickness. Steel Hinged Door with shelf closing hinges .The handle shall be Aesthetically appealing, Ergonomic, Made of Aluminum. The loacking shall be 3 way and Finish shall be Epoxy Powder coated to the thickness of 50 microns and Overall Dimensions of Floor Unit 900 W Add On shall be 900 mm(W)x500mm(D)x2025mm(H) with leveler. The construction shall be aesthetically appealing completely knock down construction. Legs shall be fitted with screw type leveler and material shall be from combination of CRCA 0.5 mm & 0.8 mm thickness. The shelving shall be height wise adjustable shelf mounting, each full shelf shall have a load capacity of 40 kg UDL max. and 4 nos. of full adjustable shelves. A4 size box file (85 W x 285 D x 345 H mm) can be stored vertically on all five loading levels. Finish shall be epoxy powder coated to the thickness of 50 microns (+/-10). The Add On units shall be stacked widthwise to form a row of storage having a common side panel etc. complete in all respect as per satisfaction of Engineer-in-charge.

Supplying and installation of Research module Laboratory Units for temprate fruits and nursery production(Waldner / Kotterman / Godrej make or equivalent) with work surface of following size with V-groove type moulding jet black Granite 20mm + - mm thick as per layout along with neoprene strip 2.5” width and 6mm thick SR 998 glue for neoprene mat complete in all respect as per satisfaction of Engineer-in-charge as well as concerned deptt. The following size of storage unit and other articles of module labs. are as under and also the Dimentlling of old existing laboratory unit due to repair the flooring and will be refixed in the same position etc. complete in all respect as per satisfaction of Engineer-in-charge. Storage Unit with Cam lock : 600 mm Depth. 750 mm Ht With metal shutter MT-1200W-600D-7H . AT-450W-600D-7H AT-1200W-600D-7H UBC-600W-450D-506H-2S UBC-450W-450D-506H-2S LS-600W-750H RP-600D-7H

Supply, Installation, Testing & Commissioning of Deep Frieze 535 Litres Capacity capable to maintain minimum temperature of -26 Degree. (Voltas/IFB/Blue star/Godrej make).

Supply & Installation of 3 Seater Petal plum sofa (Steel case/ Haworth/ Godrej/ Space wood make)

Supply & Installation of 2 Seater Petal plum sofa (Steel case/ Haworth/ Godrej/ Space wood make)

Wiring for light point / fan point / exhaust fan / call bell point with 1.5sqmm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface / recessed steel conduit and earthing the light point with 1.5 sqmm HRFRLS / PVC insulated single core copper conductor cable as required complete in all respect as per satisfaction of Engineer-in-charge (Group – C).

Wiring for Power plug with 2x4 Sqmm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface / recessed steel conduit along with 1 No. 4sqmm HRFRLS / PVC insulated single core copper conductor cable for earthing as required complete in all respect as per satisfaction of Engineer-in-charge.

Wiring for power plug with 4x4 sqmm PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface / recessed steel conduit along with 2 No. 4sqmm HRFRLS / PVC insulated single core copper conductor cable for earthing as required complete in all respect as per satisfaction of Engineer-in-charge.

Wiring for circuit / sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface / recessed steel conduit along with 1 No. HRFRLS / PVC insulated single core copper conductor cable of same size for earthing as required complete in all respect as per satisfaction of Engineer-in-charge. a)2x1.5 sqmm).

Supplying and fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess as required complete in all respect as per satisfaction of Engineer-In-charge. A) 4 modules (140mmx78mmx50mm)

Supplying and fixing following rating modular switch/socket in the existing switch box/cover plate including connections etc. as required complete in respect as per satisfaction of Engineer-In-Charge. A) S.P. 15/16 Amps one way Switch.

b) 6 pin 15/16 Amps modular socket

Supplying and fixing ceiling rose on the existing junction box/wooden block including conections etc. complete in all respect as per satisfaction of Engineer-In-Charge.

Supplying and fixing bakellite / angle holder including connections etc. as required complete in respect as per satisfaction of Engineer-In-Charge.

Supplying & erection of 6 amps. to 32 amps. rating, 10KA breaking capacity, 240 volts, ‘C’ curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a)Single pole. Category – A

Supplying and fixing following rating, double pole, 240 Volts, isolator in the existing MCB DB complete with connections etc.as required complete in all respect as per satisfaction of Engineer-in-charge. 40 Amps Category-A

Supplying and fixing of following way single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus-bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a) Single door-6 way

Providing & installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required complete in all respect as per satisfaction of Engineer-in-charge. a) Exhaust fan, Light duty , 300mm sweep.

Supplying, installation and commissioning of indoor light LED luminaire surface type T5M output complete in all respect as per satisfaction of Engineer-In-Charge (Panasonic/ Great White make) batten size of 4'-00" and wattage 22 Watt (PBTM08204/BCLAB/20MCCTBTN) anodised extracted aluminium housing high transmissibility diffuser with high lumen.

Supplying, installation and commissioning of indoor light LED luminaire surface type T5E output complete in all respect as per satisfaction of Engineer-In-Charge (Panasonic/ Great White make) batten size of 2'-00" and wattage 10 Watt (TSE 3114) anodised extracted aluminium housing high transmissibility diffuser with high lumen output.