Shri Mata Mansa Devi Shrine Board Tender

Supplying, installation, testing and commissioning of 2MP IP Dome Camera Compliance Yes/No Image Sensor: Cameras should have a size of 1/2.9” 2MP Progressive CMOS Sensor. Resolution: Cameras should have a maximum resolution of 1920(H) x 1080(V) with a maximum fps of 2MP@25/30fps. Minimum Illumination: Cameras should have a minimum illumination of Color: 0.01 Lux @F1.2 and B/W: 0.001 Lux@F1.2, 0 Lux at IR ON. Signal to Noise Ratio: Cameras should have a Signal-to-Noise Ratio greater than 60dB. Shutter Speed: Cameras should support Auto and Manual Mode with shutter speeds ranging from 1/50 sec to 1/10000 sec. IR Range: Cameras should have an IR range of 30 meters. Lens: Cameras should have a Focal Length of 3.6mm with a maximum aperture of F1.2, providing a Horizontal Angle of View of 74°, Vertical Angle of View of 58°, and Diagonal Angle of View of 88°. Image Enhancement: Cameras should support Digital Wide Dynamic Range (DWDR), Backlight Compensation (BLC), Highlight Compensation (HLC), and Automatic Gain Control (AGC). Video Compression: Cameras should support H.264/ H.265 video compression. Smart Features: Cameras should not have a Smart Codec and should support two streams. Main Stream Resolutions: Cameras should support Mainstream resolutions of 1080P (19201080) @25FPS and 720P (1280720) @25FPS. Sub Stream Resolutions: Cameras should support Sub Stream resolutions of D1/ VGA/ CIF @25 FPS. Bit Rate Range: Cameras should support a bit rate range from 27Kb to 8Mbps. Audio: Cameras should support audio. White Balance: Cameras should support White Balance adjustment. Noise Reduction: Cameras should support Auto, 2D/3D Noise Reduction (NR) with levels ranging from 1 to 5. Digital Zoom: Cameras should support Digital Zoom up to 16X with area selection using a mouse. Image Orientation: Cameras should support Flip and Mirror functions. Advanced Features: Cameras should support Region of Interest and Privacy Masking with up to 4 privacy masks. Motion Detection: Cameras should support Motion Detection.Smart Analytics Supported: Cameras should support Human Detection, Line Crossing, and Area Intrusion analytics. Network Connectivity: Cameras should have 1 x RJ45 Ethernet port supporting 10/100M adaptive Ethernet interface and should support network protocols including IPv4, TCP/IP, HTTP, HTTPS, UDP, RTSP, FTP, DHCP, DDNS, NTP, SMTP, UPnP, and IP filter. Interoperability should comply with ONVIF Profile S. Operating Conditions: Cameras should operate within a temperature range of -30°C to plus 60°C (-22°F to plus 140°F) with humidity levels less than 90% RH. Power: Cameras should support DC 12V/1Amp power input and Power over Ethernet (PoE) with a maximum power consumption of 12W. Weight: Cameras should weigh approximately 200 g. Product Certification: Shall comply with BIS, CE/FCC/UL standards Make: HIKVISION/TPLINK/DAHUA/DLINK

Supplying, installation, testing and commissioning of Tender Specification: 2MP IP Bullet Camera Image Sensor: Cameras should have a size of 1/2.9” 2MP Progressive CMOS Sensor. Resolution: Cameras should have a maximum resolution of 1920(H) x 1080(V) with a maximum fps of 2MP@25/30fps. Minimum Illumination: Cameras should have a minimum illumination of Color: 0.01 Lux @F1.2 and B/W: 0.001 Lux@F1.2, 0 Lux at IR ON. Signal to Noise Ratio: Cameras should have a Signal-to-Noise Ratio greater than 60dB. Shutter Speed: Cameras should support Auto and Manual Mode with shutter speeds ranging from 1/50 sec to 1/10000 sec. IR Range: Cameras should have an IR range of 30 meters. Lens: Cameras should have a Focal Length of 3.6mm with a maximum aperture of F1.2, providing a Horizontal Angle of View of 74°, Vertical Angle of View of 58°, and Diagonal Angle of View of 88°. Image Enhancement: Cameras should support Digital Wide Dynamic Range (DWDR), Backlight Compensation (BLC), Highlight Compensation (HLC), and Automatic Gain Control (AGC). Video Compression: Cameras should support H.264/ H.265 video compression. Smart Features: Cameras should not have a Smart Codec and should support two streams. Main Stream Resolutions: Cameras should support Mainstream resolutions of 1080P (19201080) @25FPS and 720P (1280720) @25FPS. Sub Stream Resolutions: Cameras should support Sub Stream resolutions of D1/ VGA/ CIF @25 FPS. Bit Rate Range: Cameras should support a bit rate range from 27Kb to 8Mbps. Audio: Cameras should support audio. White Balance: Cameras should support White Balance adjustment. Make: HIKVISION/TPLINK/DAHUA/DLINK

Supplying, installation, testing and commissioning of Network Video Recorder (NVR) 1. General Requirements Make and Model: To be specified by the bidder. Product Code: To be specified by the bidder. 2. Technical Specifications Network Video Input: The NVR should support 32 channels (32CH). Operating System: The NVR should operate on Embedded Linux. Network Access Bandwidth: The NVR should support 320 Mbps video bandwidth. Video Compression: The NVR should support H.265 and H.264 compression technologies. Video Output: 1 CH VGA output (1920×1080@60Hz, 1280×1024@60Hz). 1 CH HDMI output (3840×2160@30Hz, 1920×1080@60Hz, 1280×1024@60Hz). Video Preview Mode: The NVR should support 32 channels in 4K/5MP resolution. Video Bit Rate: The NVR should support a video bit rate from 16Kbps to 16Mbps. Video Resolution: The NVR should support resolutions of 4K, 5MP, 3MP, 1080P, 720P, D1, VGA, CIF, and QCIF. Preview Capability: The NVR should support 32×4K (Mainstream) and 32×D1 (Sub Stream). Image Display: The NVR should support image displays of 1, 4, 6, 8, 9, 16, and 32 images. Snapshot Mode: The NVR should support timing snapshots and manual snapshots in JPEG format. Motion Detection: The NVR should support motion detection with 396 (22x18) surveyed areas per screen and multi-level sensitivity adjustments. Privacy Mask: The NVR should support up to 4 privacy mask zones. Audio Specifications: Audio Compression: G.711u/A. Audio Output: 1 RCA. Video Recording and Playback: Video Frame Rate: 1-30 FPS. Record Mode: Manual, Schedule, Motion Detection, Timing, Intelligent analysis alarm. Playback Ability: Support for 16 channels. Playback Mode: Local video, External file playback. Record Search: The NVR should support time, calendar, and channel search. Make: HIKVISION/TPLINK/DAHUA/DLINK

Supplying, installation, testing and commissioning of Layer 2 PoE Manageable Gigabit Switch - 8 Port Make: Model Number: Switch Hardware Specification Switch with at least 8 x RJ-45 PoE Gigabit Ethernet Ports and additional 2 x 1G SFP Ports. Product Should Approved from TEC under Mandatory Testing and Certification of Telecom Equipment as notified vide Indian Telegraph (Amendment) Rules, 2017. Switching capacity should be 20Gbps or higher or non-blocking architecture. Switch packet forwarding rate should be 14Mpps or higher or non-blocking architecture. Switch MAC table should be at least 8K or higher. Switch should delivered 802.3at PoE plus and 802.3af PoE power to any of the PoE RJ-45 ports. The total power available for PoE switch should be 65W or higher. Switch should be standard 19 inch 1U rack mountable. Support for the Energy Efficient Ethernet (IEEE 802.3az) standard. Power input should be 100 to 240 V AC 50/60 Hz internal universal power supply Switch Should Support Operating Temperature -5 to 50 °C, Storage Temperature -20 to 70 °C. Switch Should Support Operating Humidity 0% to 95% relative humidity, Storage Humidity 0% to 95% relative humidity Certification: CE, FCC, RoHS and UL. Make: HIKVISION/TPLINK/DAHUA/DLINK

Supplying, installation, testing and commissioning of Layer 2 PoE Manageable Gigabit Switch - 10 Port Make: Model Number: Switch Hardware Specification Switch with at least 8 x RJ-45 PoE Gigabit Ethernet Ports and additional 2 x 1G SFP Ports. Product Should Approved from TEC under Mandatory Testing and Certification of Telecom Equipment as notified vide Indian Telegraph (Amendment) Rules, 2017. Switching capacity should be 20Gbps or higher or non-blocking architecture. Switch packet forwarding rate should be 14Mpps or higher or non-blocking architecture. Switch MAC table should be at least 8K or higher. Switch should delivered 802.3at PoE plus and 802.3af PoE power to any of the PoE RJ-45 ports. The total power available for PoE switch should be 65W or higher. Switch should be standard 19 inch 1U rack mountable. Support for the Energy Efficient Ethernet (IEEE 802.3az) standard. Power input should be 100 to 240 V AC 50/60 Hz internal universal power supply Switch Should Support Operating Temperature -5 to 50 °C, Storage Temperature -20 to 70 °C. Switch Should Support Operating Humidity 0% to 95% relative humidity, Storage Humidity 0% to 95% relative humidity Certification: CE, FCC, RoHS and UL. Make: HIKVISION/TPLINK/DAHUA/DLINK

Supplying, installation, testing and commissioning of Layer 2 PoE Manageable Gigabit Switch - 16 Port Make: Model Number: Switch Hardware Specification Switch with at least 24 X RJ-45 PoE Gigabit Ethernet Ports and additional 4 X Combo (SFP/RJ-45) 1G Ports. Product Should Approved from TEC under Mandatory Testing and Certification of Telecom Equipment as notified vide Indian Telegraph (Amendment) Rules, 2017. Switching capacity should be 56Gbps or higher or non-blocking architecture. Switch packet forwarding rate should be 41Mpps or higher or non-blocking architecture. Switch MAC table should be at least 8K or higher. Switch should delivered 802.3at PoE plus and 802.3af PoE power to any of the PoE RJ-45 ports. The total power available for PoE switch should be 193W or higher. Switch should be standard 19 inch 1U rack mountable. Support for the Energy Efficient Ethernet (IEEE 802.3az) standard. Power input should be 100 to 240 V AC 50/60 Hz internal universal power supply Switch Should Support Operating Temperature -5 to 50 °C (23 to 122 °F), Storage Temperature -20 to 70 °C. Switch Should Support Operating Humidity 0% to 95% relative humidity, Storage Humidity 0% to 95% relative humidity Certification: CE, FCC, RoHS and UL. Make: CPPLUS/TPLINK/DAHUA/DLINK

Dressing of Rack and repair of exiting CCTV System Complete with laboure and minner parts

Supplying, installation, testing and commissioning of Wall Mount Rack Specification - 15Ux550Wx500D Rack Shall have Front Glass Door (tinted, Toughened) with Lock and Key Rack Shall have 2 pairs of 19` Mounting Rails with U-Marking Rack Shall have Provision to mount cooling fans Unit / 90 CFM /230V AC (1 No) on the top panel Rack shall Conforms to DIN 41494 OR equivalent ISO Standards Rack shall have Welded Side Walls, CRCA steel Frame and powder coated with highest quality standards. Rack Shall have 19” Mounting angles made of formed steel Rack Shall have Depth adjustable mounting slots for verticals provide better mounting flexibility and maximizes the usable mounting space Rack Shall have Top and bottom Panel with ventilation and cable entry facility Rack Shall be Powder coated finish with pretreatment process meeting all industry standards Rack Shall have Grounding and Bonding Options. 100% assured compatibility with all equipment conforming to DIN 41494 (General industrial standard for equipment) Rack Shall be Welded to Frame Top and Bottom Cover, Vented and Field Cable entry exit cut outs 1U Cable Manager (1), Hardware Pkt of 20 (1 Pkt), 6 Socket 5 Amp. Power Distribution Unit (1 No), Rack Shall have Standard Color : Grey, Static Load : 40 kgs OEM Eligibility Criteria for Racks Components OEM Should be International certification for the ISO 45001 Health and Safety Management System, ISO 9001 Quality Management System, ISO 14001 Environmental Management System, and ISO 14064-1 Greenhouse Gas Inventory Standards. OEM should have Indian based operation at least for a period of 20 plus years and should have an Annual Turnover of Rs. 500 Crores and above in any of last three consecutive Audited Financial years. (To ensure only principal networking companies participate having strong Product , Support and Service.)

Supplying, installation, testing and commissioning of Wall Mount Rack Specification - 4U Rack Shall have Front Glass Door (tinted, Toughened) with Lock and Key Rack Shall have 2 pairs of 19` Mounting Rails with U-Marking Rack Shall have Provision to mount cooling fans Unit / 90 CFM /230V AC (1 No) on the top panel Rack shall Conforms to DIN 41494 OR equivalent ISO Standards Rack shall have Welded Side Walls, CRCA steel Frame and powder coated with highest quality standards. Rack Shall have 19” Mounting angles made of formed steel Rack Shall have Depth adjustable mounting slots for verticals provide better mounting flexibility and maximizes the usable mounting space Rack Shall have Top and bottom Panel with ventilation and cable entry facility Rack Shall be Powder coated finish with pretreatment process meeting all industry standards Rack Shall have Grounding and Bonding Options. 100% assured compatibility with all equipment conforming to DIN 41494 (General industrial standard for equipment) Rack Shall be Welded to Frame Top and Bottom Cover, Vented and Field Cable entry exit cut outs 1U Cable Manager (1), Hardware Pkt of 20 (1 Pkt), 6 Socket 5 Amp. Power Distribution Unit (1 No), Rack Shall have Standard Color : Grey, Static Load : 40 kgs OEM Eligibility Criteria for Racks Components OEM Should be International certification for the ISO 45001 Health and Safety Management System, ISO 9001 Quality Management System, ISO 14001 Environmental Management System, and ISO 14064-1 Greenhouse Gas Inventory Standards. OEM should have Indian based operation at least for a period of 20 plus years and should have an Annual Turnover of Rs. 500 Crores and above in any of last three consecutive Audited Financial years. (To ensure only principal networking companies participate having strong Product , Support and Service.)

Supplying, installation, testing and commissioning of FIBER Cable 6 core complete in all respect.

Supplying and drawing of Optical Fiber Pigtail – SC Type 1 Meter Make: Model Number:Provide a field installable Single mode SC pigtails to terminate fiber optic cables from cable-to-cable, cable-to-equipment and equipment-to-equipment. Utilize a UPC polishing on the tip to provide high yield during installation. Meet TIA/EIA 568.C.3 standards for repeatability. Buffer diameter 900um Tight buffer, Minimum bend Radius: Install :30mm, Retention Strength: 20N, Cable: 900um Buffered Insertion Loss (Max) (0.3 db Max, Return Loss )/= 50 db for UPC Connector ferrule Ceramic, SC Type Simplex Type, Cable Color Yellow Repeatability ( 0.2dB 200 times Mating Cycle Working Temp. -10 deg. C to plus 70 deg. C, Storage Temp. -20 deg. C to plus 70 deg. C Make : Molex/ Panduit/ Systimax

Supplying, installation, testing and commissioning of VGA Splitter 4 port 1 input 4 output complete in all respect upto intire satifications in Enggineer Encharge.

Supplying, installation, testing and commissioning of 6TB Hard Disk for Storage of DATA complete in all respect upto intire satifications in Enggineer Encharge.

Fiber/Media Converter 1 port 10/100 media converter complete in all respect. Make : Secureye/Dlink

Supply , Testing and commissioning of Optical Fiber Equipment Cords - SC-LC Duplex Make: Model Number: Optical fiber patch leads shall comprise of Single mode 9/125µm fiber with LC-SC fiber connectors terminated at each end.The optical fiber patch leads shall be compatible with industry standards (EIA/TIA, IEC, ANSI). Adopts high precision ceramic ferrule with good concentricity. 100% inspected for optical characteristics and fiber end face finish. Low insertion loss and return loss, clean and scratch-free end faces. Good performance endurance under changing circumstances. 9/125µm Single mode G652D, Duplex Type Pre-radiuses and pre-polished ferrule Insertion Loss (0.3 db , Return Loss )/= 50dB for UPC Repeatability ( 0.2dB 1000 times Mating Cycle Working Temperature –10°C ~ plus 70°C, Storage Temperature –20°C ~ plus 70°C Cable yellow Color, Length 1m, 2m and 3m Meter Other lengths on request.