Public Works Department Tender

Supply, installation, testing and commissioning of Secondary Chilled Water duty Vertical inline split coupled (long coupled centrifugal pumps factory mounted electric motor and pump motor, IP-55 VFD for re circulation of water for the central air conditioning system. The pump motor shall be of IE-3 class efficiency, TEFC Squirrel cage  class -F insulation, 1450/2900 rpm, BMS compatible and suitable for 415 Volts ± 10%, 50 cycles, 3 phase power supply. The pump should be complete with all necessary accessories mechanical seals, gland drain connections mechanical coupling, coupling guards etc.The internal components of pumps including mechanical seal shall be suitable to sustain a temperature of 122 degree fehrenheit. Pumping sysetm along with VFD shall be capable to operate on Sensorless/ DPT signal along wth applicable controller. Refer Specs for more details To monitor the performance and change the pump quadratic curve of the the pump for site requirement of head and flow, this can be done by the pump in build sensorless logics or by providing Flow meter(For Flow) and Digital DPT(For Head) for each pump and integrating the same with the PID`s available with in the VFD. The above item Included with following inbuilt controller The Above item shall be included with Dedicated microprocessor based pump logic controller, parallel pumping software duly downloaded, sensorless logic, interfacing amongst all components and compatibility of I/O signals, BMS compatible etc complete with other accessories as required. It should be complete as per manufacturer`s Specifications and as directed by Engineer-in-charge.multiple differential pressure sensor/ transmitters( Minimum 5 nos) as per the site requirement. VFD shall be capable to operate on Sensorless Control application along wth controller. Controller should have parallel pump logic to operate all set of the pumps with the following features: -Parallel pump operation for power savings. - Controller shall control pump VFD`s as per building load variation. Microprocessor controller shall not be mounted on any of the VFD and should be standalone system to have equipments better performance/ Efficiency and reliability. 1 set. Note:- Pump`s motor should be BMS Compatible Pump logic Controller shall be individual for individual block Vendor shall be submit Pump performance curve and efficiency curve alongwith offer The above mentioned pumps shall include following: a) 1 No.- Pump with minimum 75 ± 5% Efficiency b) 1 No. - Suitable HP TEFC squirrel cage induction type IE3 motor with class `F` insulation 1500 rpm synchronous speed, operating on 415 plus 10% volts, 3 phase, 50 Hz A.C. supply. c) Rubber Below Flexible type with MS flanges at inlet and oulet connections of the pump/ Not required in Vibrationless pumps d) Lot- RCC Foundation with Anivibration pads / Not require for vibrationless pumps 6.1 For Hospital Block: Water flow rate: 840 USGPM, Head : 27 mtrs Final Head furnished by vendor. The mentioned head is indicative purpose. (02 Working plus 01 Standby) (Rates are of GST excluded).

Supply, installation, testing and commissioning of Secondary Chilled Water duty Vertical inline split coupled (long coupled centrifugal pumps factory mounted electric motor and pump motor, IP-55 VFD for re circulation of water for the central air conditioning system. The pump motor shall be of IE-3 class efficiency, TEFC Squirrel cage  class -F insulation, 1450/2900 rpm, BMS compatible and suitable for 415 Volts ± 10%, 50 cycles, 3 phase power supply. The pump should be complete with all necessary accessories mechanical seals, gland drain connections mechanical coupling, coupling guards etc.The internal components of pumps including mechanical seal shall be suitable to sustain a temperature of 122 degree fehrenheit. Pumping sysetm along with VFD shall be capable to operate on Sensorless/ DPT signal along wth applicable controller. Refer Specs for more details To monitor the performance and change the pump quadratic curve of the the pump for site requirement of head and flow, this can be done by the pump in build sensorless logics or by providing Flow meter(For Flow) and Digital DPT(For Head) for each pump and integrating the same with the PID`s available with in the VFD. The above item Included with following inbuilt controller The Above item shall be included with Dedicated microprocessor based pump logic controller, parallel pumping software duly downloaded, sensorless logic, interfacing amongst all components and compatibility of I/O signals, BMS compatible etc complete with other accessories as required. It should be complete as per manufacturer`s Specifications and as directed by Engineer-in-charge.multiple differential pressure sensor/ transmitters( Minimum 5 nos) as per the site requirement. VFD shall be capable to operate on Sensorless Control application along wth controller. Controller should have parallel pump logic to operate all set of the pumps with the following features:-Parallel pump operation for power savings. - Controller shall control pump VFD`s as per building load variation. Microprocessor controller shall not be mounted on any of the VFD and should be standalone system to have equipments better performance/ Efficiency and reliability. 1 set. Note:- Pump`s motor should be BMS Compatible Pump logic Controller shall be individual for individual block Vendor shall be submit Pump performance curve and efficiency curve alongwith offer The above mentioned pumps shall include following: a) 1 No.- Pump with minimum 75 ± 5% Efficiency b) 1 No. - Suitable HP TEFC squirrel cage induction type IE3 motor with class `F` insulation 1500 rpm synchronous speed, operating on 415 plus 10% volts, 3 phase, 50 Hz A.C. supply. c) Rubber Below Flexible type with MS flanges at inlet and oulet connections of the pump/ Not required in Vibrationless pumps d) Lot- RCC Foundation with Anivibration pads / Not require for vibrationless pumps 6.2 For OPD Block: Water flow rate: 360 USGPM, Head : 32 mtrs Final Head furnished by vendor. The mentioned head is indicative purpose. (01 Working plus 01 Standby) (Rates are of GST excluded).

Supply, Installation, Testing and Commissioning of Condenser Water duty centrifugal Vertical inline split coupled (long pumps with mechanical seal, complete with motor, drain valves and other accessories (except suction and discharge shut off valves, suction strainer, discharge check valves and drain piping which are covered under separate item). Pumps shall have a mechanical seal and CI casing and Bronze / SS (CF8) IImpeller, SS Shaft. The pump motor shall be of IE-3 class efficiency, TEFC Squirrel cage  class -F insulation, suitable for 415 Volts ± 10%, 50 cycles, 3 phase power supply. The quoted price shall include cost of M.S supports for mounting both pump with motor and coupling guard etc. Pumps shall be complete as per specifications and shall have operating parameters as given below. The internal components of pumps including mechanical seal shall be suitable to sustain a temperature of 122 degree Fahrenheit.   Note:- Pump`s motor should be BMS Compatible Vendor shall be submit Pump performance curve and efficiency curve alongwith offer The above mentioned pumps shall include following: a) 1 No.- Pump with minimum 75 % Efficiency b) 1 No. - Suitable HP TEFC squirrel cage induction type IE3 motor with class `F` insulation 1500 rpm synchronous speed, operating on 415 plus 10% volts, 3 phase, 50 Hz A.C. supply. c) Rubber Below Flexible type with MS flanges at inlet and oulet connections of the pump d) Lot- RCC Foundation with Antivibration pads. e) Water flow rate:1600 USGPM, Head : 36 mtrs Vendor shall be furnished final USGPM flow as per chiller Final Head furnished by vendor. The mentioned head is indicative purpose. (02 Working plus 01 Standby) (Rates are of GST excluded).

Supply, Installation, Testing and Commissioning of Hot Water Generator`s Pump duty centrifugal Vertical inline split coupled (long coupled) pumps for monsoon Reheat with mechnical seal, complete with motor, drain valves and other accessories (except suction and discharge shut off valves, suction strainer, discharge check valves and drain piping which are covered under separate item).Pumps shall have mechanical seal and CI casing and Bronze Impeller, SS Shaft. The pump motor shall be of IE-3 class efficiency, TEFC Squirrel cage  class -F insulation, suitable for 415 Volts ± 10%, 50 cycles, 3 phase power supply. The quoted price shall include cost of M.S supports for mounting both pump with motor and coupling guard etc. Pumps shall be complete as per specifications and shall have operating parameters as given below. The internal components of pumps including mechanical seal shall be suitable to sustain a temperature of 122 degree fehrenheit. Vendor shall be provide with antivibration arrangement for pumps as per specification if applicable. To monitor the performance and change the pump quadratic curve of the the pump for site requirement of head and flow, , this can be done by the pump in build sensorless logics or by providing Flow meter(For Flow) and Digital DPT(For Head) for each pump and integrating the same with the PID`s available with in the VFD. Note:- Pump`s motor should be BMS Compatible Vendor shall be submit Pump performance curve and efficiency curve alongwith offer The above mentioned pumps shall include following: a) 1 No.- Pump with minimum 75 ± 10% Efficiency b) 1 No. - Suitable HP TEFC squirrel cage induction type IE3 motor with class `F` insulation 1500 rpm synchronous speed, operating on 415 plus 10% volts, 3 phase, 50 Hz A.C. supply. c) Rubber Below Flexible type with MS flanges at inlet and oulet connections of the pump/ Not required in Vibrationless pumps Lot- RCC Foundation with Anivibration pads / Not require for vibrationless pumps e) Water flow rate: 430 LPM, Head : 27 mtrs (01 Working plus 01 Standby) (Rates are of GST excluded).

PAN TYPE HUMIDIFIER For OT Supplying, installation,testing and commissioning of Humidification package of 2mm thick stainless steel sheet SS-304 duly insulated with 50 mm thick fibre glass and aluminum claded with all necessary controls such as low-level cutout, float valve, heating thermostat, high-temperature cutout, electricals panel with digital Humidistat with all necessary control wiring and interlocking with each other accessories like transformer 24V etc as required and as per standard specification and of following capacities: 4.5 KW (Rates are of GST excluded).

AIR HANDLING UNITS :- FLOOR MOUNTED AIR HANDLING UNITS WITH MIXING CHAMBER and ADDITIONAL HEATING COIL Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with Mixing Chamber included Fresh air damper with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick SS 304 Stainless Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section and 2 RD Heating coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet 3000 CFM / 120 mmwg St. Pressure - For OT (except minor) (Rates are of GST excluded).

AIR HANDLING UNITS :- FLOOR MOUNTED AIR HANDLING UNITS WITH MIXING CHAMBER and ADDITIONAL HEATING COIL Supply, Installation, Testig and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with Mixing Chamber included Fresh air damper with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick SS 304 Stainless Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section and 2 RD Heating coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet 2000 CFM / 60 mmwg St. Pressure - CT and MRI Room (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For OPD Block: 11000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For OPD Block: 7500 CFM / 60 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For OPD Block: 6500 CFM / 60 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For OPD Block: 5500 CFM / 60 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For Hospital Block: 6000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For Hospital Block: 8000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For Hospital Block: 9000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For Hospital Block: 10000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For Hospital Block: 12000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For Hospital Block: 13000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For Hospital Block: 14000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet For Hospital Block: 16500 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS WITH HEATING COIL :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section and 2 RD Heating coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1+B36 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet 19000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS WITH HEATING COIL :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section and 2 RD Heating coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet 12000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS WITH HEATING COIL :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section and 2 RD Heating coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet 10000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS WITH HEATING COIL :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section and 2 RD Heating coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE:1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet 9000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS WITH HEATING COIL :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section and 2 RD Heating coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet 8000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

FLOOR MOUNTED AIR HANDLING UNITS WITH HEATING COIL :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 6 RD cooling coil with coil section and 2 RD Heating coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% and combined with fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) before cooling coil. The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB70 @ 1 Meter at AHU discharge outlet 6000 CFM / 65 mmwg St. Pressure (Rates are of GST excluded).

CEILING SUSPENDED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 4 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% before cooling coil, fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) in supply . The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB 55 - 58 @ 1.5 Meter at discharge outlet For OPD Block: 3500 CFM / 50 mmwg St. Pressure (Rates are of GST excluded).

CEILING SUSPENDED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 4 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% before cooling coil, fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) in supply . The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB 55 - 58 @ 1.5 Meter at discharge outlet For OPD Block: 2500 CFM / 50 mmwg St. Pressure (Rates are of GST excluded).

CEILING SUSPENDED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 4 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% before cooling coil, fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) in supply . The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB 55 - 58 @ 1.5 Meter at discharge outlet For Hospital Block: 1200 CFM / 40 mmwg St. Pressure (Rates are of GST excluded).

CEILING SUSPENDED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 4 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% before cooling coil, fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) in supply . The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB 55 - 58 @ 1.5 Meter at discharge outlet For Hospital Block: 2000 CFM / 50 mmwg St. Pressure (Rates are of GST excluded).

CEILING SUSPENDED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 4 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% before cooling coil, fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) in supply . The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB 55 - 58 @ 1.5 Meter at discharge outlet For Hospital Block: 2500 CFM / 50 mmwg St. Pressure (Rates are of GST excluded).

CEILING SUSPENDED AIR HANDLING UNITS :- Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick 180 GSM Galvanised Steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 4 RD cooling coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% before cooling coil, fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) in supply . The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB 55 - 58 @ 1.5 Meter at discharge outlet For Hospital Block: 3000 CFM / 50 mmwg St. Pressure (Rates are of GST excluded).

CEILING SUSPENDED AIR HANDLING UNITS WITH HEATING COIL Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick SS 304 stainless steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 4 RD cooling coil with coil section and 2 RD Heating coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% before cooling coil, fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) in supply . The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB 55 - 58 @ 1.5 Meter at discharge outlet For Hospital Block: 2000 CFM / 60 mmwg St. Pressure (Rates are of GST excluded).

CEILING SUSPENDED AIR HANDLING UNITS WITH HEATING COIL Supply, Installation, Testing and Commissioning of factory fabricated Indoor Type Double Skinned air-handling unit horizontal type with fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.8 mm thick precoated galvanised sheet outside and 0.8 mm thick SS 304 stainless steel sheet inside with Backward curved direct driven plug type Metallic construction in supply with fan section with fan motor with IE3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz along with IP 20 VFD, 4 RD cooling coil with coil section and 2 RD Heating coil with coil section, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90% before cooling coil, fine filter ( EU-7 / F7 ) / MERV-13 section with Synthetic fibre media with frame material made out by Aluminium anodized with flange rigid media with efficiency 99 % at 3µ (micron) in supply . The polished stainless steel drain pan of 1.25 mm thick duly insulated with 13 mm thick nitrile rubber under cooling coil shall be provided. Motor and direct driven arrangement, blower without face and bypass dampers. The AHU panel shall be insulated with 43 mm thick injected fire retardent PUF of density 38 plus /-2Kg/m³. The motor and fan assembly shall be mounted on aluminium extruded section .Marine light with limit switch shall be provided . The complete AHU shall conform to standard spec.The face velocity across cooling / heating coil, filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch NOTE: 1. Magnehelic differential pressure gauge required with fine filter and same shall be included in AHU. `2. AHU, Fans and Coil should be AHRI / EUROVENT Certified: Casing Deflection : CD1 / D1 Casing Air Leakage : CL1 / L1 Thermal Transmittance : CT2 / T2 Thermal Brdigging : CB1 / TB2` 3. Noise Level should not be exceed dB 55 - 58 @ 1.5 Meter at discharge outlet For Hospital Block: 3000 CFM / 60 mmwg St. Pressure (Rates are of GST excluded).

FCU Units :- Supply ,Installation ,Testing and commissioning of Fan coil units (AHRI certified) complete with twin blower, 3 speed motor 230 ± 10 % volts, single phase, 50 Hz, A.C. supply, 3 row deep cooling coil (AHRI certified), synthetic washable fitter, insulated S.S. drain pan tray, copper connection, rotary switch, supporting arrangement, electrical wiring etc. The fan shall be selected for 06 mm static pressure (normal). The AHRI certified FCU shall be included with Valve Station duly insulated (01 No. isolation Ball valve, 01 No. isolation Ball valve with strainer and motorised PIDB(on/off type) / High rangeability valve).The complete fan coil unit shall be in line with the standard specification and positioning confirmed as per tender Drawing. AHRI Certified Software Selection sheet to be submitted. The capacity of fan coil units shall be as follows: GA Drawing and Technical Data sheets should be get approval before dispatch For Hospital Block: Capacity: 1.5 TR / 600 CFM (Rates are of GST excluded).

FCU Units :- Supply ,Installation ,Testing and commissioning of Fan coil units (AHRI certified) complete with twin blower, 3 speed motor 230 ± 10 % volts, single phase, 50 Hz, A.C. supply, 3 row deep cooling coil (AHRI certified), synthetic washable fitter, insulated S.S. drain pan tray, copper connection, rotary switch, supporting arrangement, electrical wiring etc. The fan shall be selected for 06 mm static pressure (normal). The AHRI certified FCU shall be included with Valve Station duly insulated (01 No. isolation Ball valve, 01 No. isolation Ball valve with strainer and motorised PIDB(on/off type) / High rangeability valve).The complete fan coil unit shall be in line with the standard specification and positioning confirmed as per tender Drawing. AHRI Certified Software Selection sheet to be submitted. The capacity of fan coil units shall be as follows: GA Drawing and Technical Data sheets should be get approval before dispatch For Hospital Block: Capacity: 2.0 TR / 800 CFM (Rates are of GST excluded).

Kitchen Ventilation System :- Air Washer for Make Air Supply, installation, testing and commissioning of factory fabricated double skinned Cellulose Fill type Air Washer for Kitchen Make up Fresh Air made of 25 mm thick panels consisting of G.I. Casing of thickness 0.63 mm outside layer made out by 180 GSM GI sheet and 0.63 mm inside layer made out by stainless steel (SS 304) with polyurethene foam (PUF) and 38Kg/m³ density insulation factory injected between them by injection moulding machine, giving 90% saturation efficiency at 500 FPM air velocity across pads, factory assembled with fan section having multiple DIDW Backward curved blower with minimum 200 mm deep cellulose paper pads for humidification having water distribution arrangement and suitable rating water circuilating pump. Water tank shall be of stainless steel (SS 304) thickness not less than 1.6 mm having necessary arrangement of water inlet with float valve, over flow and drain arrangement. complete with Aluminum wiremess / viscous Pre filters section with 20µ (micron) particle size with an efficiency of 75% and belt drive package with TEFCsq cage induction drive motor type IE-2 suitable for 415 plus 10% volts, 50 Hz, 3 phase AC supply. The airwasher shall be complete with 02 No. water circulation pump in built inside the air washer casing The unit shall be integrated and connected with fan section including all necessary accessories to complete the installation etc. as per specifications and Drawings of following capacities. Unit to be blow thru type to avoid water caryover on Fan and motor . GA Drawing and technical Data sheets should be get approval before dispatch 16000 CFM @ 50 MMWG (Rates are of GST excluded).

Dry Scrubber for Exhaust Air Supply, Installation, Testing and Commissioning of Electrostatic Type Kitchen Exhaust Air Cleaner (Dry Scrubber) with SISW fan section complete with the following accessories, components etc. making it a completely functional dry scrubber suitable for Kitchen Hood Exhaust. i) Casing - Shall be made of 0.63 mm galvanized pre-plasticized/powder coated sheet on outside and 0.63 mm GI sheet inside with PUF foam of 36 kg/m3 density insulation in between sheets to make 25 mm thick panels. ii) Pre Filter Section with Wire Mesh SS Filters for Coarse Particle Removal iii) Electrostatic Precipitator Section - Electrostatic section shall be made of 16 gauge galvanised sheet, high bake epoxy powder coated, SS Spiked ionizers to create high voltage DC field, aluminium collector plates which should be alternatively charged positive and negative with large collecting area with deep cell, to work as magnet for charged smoke and oil particles. Average efficiency of 90-95% in single pass as per ASHRAE test method. Electrostatic Precipitator should be able to charge particles from 0.01 micron to 10 microns through solid state power supply. Collector cell should be of permanent type and incorporate slide out facility for easy removal for cleaning. Power supplies(UL Listed) shall be 100% solid state. Operating Voltage : 220V, 50 Hz and Ionizing Voltage : 12 to 13 KVDC. The system shall be allow connection to a fan section to achieve 500 - 650 FPM velocity across the air cleaner. The units shall be included with V Shaped Adsorber Module feature as per specification. iv) Fan Section with SISW Curved Fan having following capacity @ specified SP and should be complete with suitable TEFC Induction Motor and Belt Drive arrangements. GA Drawing and technical Data sheets should be get approval before dispatch Capacity: 18000 cfm @ 75mmwg SP Proposed Motor: 7.5 KW. (Rates are of GST excluded).

Supply, Installation, Testing and Commissioning of factory fabricated Double Skinned DIDW fan section horizontal type fabricated out of extruded aluminium (1.6 mm thickness min.)section with 0.63mm thick pre-plasticide galvanised sheet outside and 0.63mm thick polished galvanised Steel sheet inside backward curved direct driven plug type / DIDW belt driven with fan motor with IE-3 rating and suitable for 415 plus 10%, 3 Phase, 50 Hz, prefilter (EU-4) section with non woven synthetic washable media of 10µ (micron) particle size with an efficiency of 90%, fine filter ( EU-7 / F7 ) section with Synthetic fibre media with frame material made out by Aluminium anodized with flange bag type media with efficiency 99 % at 3µ (micron) and HEPA filters shall have the efficiency of 99.97% down to 0.3 micron particle size. The Fan section shall be insulated with 25 mm thick injected fire retardent PUF of density 38 plus /-2 Kg/m³ . The motor and fan assembly shall be mounted on aluminium extruded section .The complete fan section shall conform to standard spec.The face velocity across filters should not exceed 500 FPM. The capacities of airhandling shall be as follows GA Drawing and technical Data sheets should be get approval before dispatch Manufacturer shall furnish AMCA Test Certificate for air performance.3. Noise Level should not be exceed dB 56 @ 1 Meter 800 CFM / St Pr.110 mm Wg - For Negative Isolation room / Septic Room (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:-Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For Basement Ventilation: For OPD Block: 5500 CFM / 20 mm Wg / dB 72 @ 3 Meter / Efficiency not less than 65 % - For zone-1 (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity: Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For Basement Ventilation: For OPD Block: 5000 CFM / 20 mm Wg / dB 72 @ 3 Meter / Efficiency not less than 65 % - For zone-2 (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:-Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For Basement Ventilation: For OPD Block: 1200 CFM / 15 mm Wg / dB 74 @ 3 Meter / Efficiency not less than 65 % - For Pump Room (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:-Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For Basement Ventilation: For Hospital Block: 25000 CFM / 25 mm Wg / dB 72 @ 3 Meter / Efficiency not less than 65 % - For zone-1and2 (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :-Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:-Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For Basement Ventilation: For Hospital Block: 5500 CFM / 15 mm Wg / dB 72 @ 3 Meter / Efficiency not less than 65 % - For AC Plant Room (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:-Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For Basement Ventilation: For Hospital Block: 4000 CFM / 15 mm Wg / dB 72 @ 3 Meter / Efficiency not less than 65 % - For Electrical Panel Room (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:-Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For Basement Ventilation: For Hospital Block: 2500 CFM / 15 mm Wg / dB 72 @ 3 Meter / Efficiency not less than 65 % - For Store Room 1and2. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For Basement Ventilation: For Hospital Block: 2000 CFM / 15 mm Wg / dB 72 @ 3 Meter / Efficiency not less than 65 % - For Fire Pump Room. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For OPD Block: 9500 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:-Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For OPD Block: 9000 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For OPD Block: 8500 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:-Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For OPD Block: 7500 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:-Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For Hospital Block: 12000 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For Hospital Block: 10000 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For Hospital Block: 9000 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For Hospital Block: 7000 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For Hospital Block: 6000 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For Hospital Block: 5500 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fan for Smoke Exhaust Air :- Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS with powder double coated / High duty GSS long Casing, cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `H` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc..Motor shall be suitable for 250 °C temperature rated for 2 hours and shall be completely be accommodated inside the fan casing.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch For occupied zone smoke exhaust : For Hospital Block: 3500 CFM / 25 mm Wg / Efficiency not less than 65 %. (Rates are of GST excluded).

Axial Flow Fans for make up Fresh Air - Basement AC Plant Room Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS MS with powder double coated / High duty GSS long Casing , cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `F` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and technical Data sheets should be get approval before dispatch 5500 CFM / 15 mm Wg / dB 72 @ 3 Meter / Efficiency not less than 65 % - For AC Plant Room (Rates are of GST excluded).

Axial Flow Fans for Liftwell Pressurization Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS MS with powder double coated / High duty GSS long Casing , cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `F` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and Technical Data sheets should be get approval before dispatch For OPD Block 8000 CFM / 20 mm Wg (Rates are of GST excluded).

Axial Flow Fans for Liftwell Pressurization Supply,installation,testing and commissining of direct driven Tube axial flow fans suitable for installing in any position in Horizontal or vertical with adjustable pitch blade, MS MS with powder double coated / High duty GSS long Casing , cast aluminium alloy impeller complete with TEFC Sq. Cage Induction type IE-3 motor suitable for 415 volts ± 10%, 50Hz ± 3 %, 4 Pole, three phase A.C supply of class `F` insulation motor`s winding with support, mountings, vibration isolators, fire retardant flexible canvass connector 150 mm deep with 25 mm slack at Outlet etc.The fans shall be as per specifications and tender Drawing of following capacity:- Thickness of the casing shall not be less than: For Dia (300 to 650) mm – 2mm, Dia (700 to 1140) mm – 3 mm, Dia (1200 to 1400) mm – 4mm and Dia 1600 – 5 mm.Multi piece casing is not accepted. Manufacturer shall furnish AMCA Test Certificate for air performance along with fire test certificate (Latest) for each fan sourced from that particular factory. GA Drawing and Technical Data sheets should be get approval before dispatch For Hosital Block 9000 CFM / 20 mm Wg (Rates are of GST excluded).

Supply, installation, testing and commissioning of Circular / Rectangular type Ducted Inline fans with motor complete with TEFC Sq. Cage Induction motor suitable for 220 volts ± 10%, 50Hz ± 3 %, single phase A.C supply of class `F` insulation with , mountings accessories in all respect with wiring upto power supply point and of following capacities and as per tender drawing: GA Drawing and Technical Data sheets should be get approval before dispatch For OPD Block 400 CFM / 20 mm WG total St. Press./ dB level not to exceed 45 @ 3.0 Meter. (Rates are of GST excluded).

Supply, installation, testing and commissioning of Circular / Rectangular type Ducted Inline fans with motor complete with TEFC Sq. Cage Induction motor suitable for 220 volts ± 10%, 50Hz ± 3 %, single phase A.C supply of class `F` insulation with , mountings accessories in all respect with wiring upto power supply point and of following capacities and as per tender drawing: GA Drawing and Technical Data sheets should be get approval before dispatch For OPD Block 350 CFM / 20 mm WG total St. Press./ dB level not to exceed 45 @ 3.0 Meter. (Rates are of GST excluded).

Supply, installation, testing and commissioning of Circular / Rectangular type Ducted Inline fans with motor complete with TEFC Sq. Cage Induction motor suitable for 220 volts ± 10%, 50Hz ± 3 %, single phase A.C supply of class `F` insulation with , mountings accessories in all respect with wiring upto power supply point and of following capacities and as per tender drawing: GA Drawing and Technical Data sheets should be get approval before dispatch For Hospital Block 750 CFM / 20 mm WG total St. Press./ dB level not to exceed 45 @ 3.0 Meter. (Rates are of GST excluded).

Supply, installation, testing and commissioning of Circular / Rectangular type Ducted Inline fans with motor complete with TEFC Sq. Cage Induction motor suitable for 220 volts ± 10%, 50Hz ± 3 %, single phase A.C supply of class `F` insulation with , mountings accessories in all respect with wiring upto power supply point and of following capacities and as per tender drawing: GA Drawing and Technical Data sheets should be get approval before dispatch For Hospital Block 600 CFM / 20 mm WG total St. Press./ dB level not to exceed 45 @ 3.0 Meter. (Rates are of GST excluded).

Supply, installation, testing and commissioning of Circular / Rectangular type Ducted Inline fans with motor complete with TEFC Sq. Cage Induction motor suitable for 220 volts ± 10%, 50Hz ± 3 %, single phase A.C supply of class `F` insulation with , mountings accessories in all respect with wiring upto power supply point and of following capacities and as per tender drawing: GA Drawing and Technical Data sheets should be get approval before dispatch For Hospital Block 450 CFM / 20 mm WG total St. Press./ dB level not to exceed 45 @ 3.0 Meter. (Rates are of GST excluded).

Supply, installation, testing and commissioning of Circular / Rectangular type Ducted Inline fans with motor complete with TEFC Sq. Cage Induction motor suitable for 220 volts ± 10%, 50Hz ± 3 %, single phase A.C supply of class `F` insulation with , mountings accessories in all respect with wiring upto power supply point and of following capacities and as per tender drawing: GA Drawing and Technical Data sheets should be get approval before dispatch For Hospital Block 300 CFM / 15 mm WG total St. Press./ dB level not to exceed 45 @ 3.0 Meter. (Rates are of GST excluded).

Supply, installation, testing and commissioning of Circular / Rectangular type Ducted Inline fans with motor complete with TEFC Sq. Cage Induction motor suitable for 220 volts ± 10%, 50Hz ± 3 %, single phase A.C supply of class `F` insulation with , mountings accessories in all respect with wiring upto power supply point and of following capacities and as per tender drawing: GA Drawing and Technical Data sheets should be get approval before dispatch For Hospital Block 250 CFM / 15 mm WG total St. Press./ dB level not to exceed 45 @ 3.0 Meter. (Rates are of GST excluded).

Supply, installation, testing and commissioning of Circular / Rectangular type Ducted Inline fans with motor complete with TEFC Sq. Cage Induction motor suitable for 220 volts ± 10%, 50Hz ± 3 %, single phase A.C supply of class `F` insulation with , mountings accessories in all respect with wiring upto power supply point and of following capacities and as per tender drawing: GA Drawing and Technical Data sheets should be get approval before dispatch For Hospital Block 200 CFM / 15 mm WG total St. Press./ dB level not to exceed 45 @ 3.0 Meter. (Rates are of GST excluded).

Supply, installation, testing and commissioning of Cassette type ceiling mounted ventilation fan balanced turbine curved blade type fan made out by high impact ABS plastic with round spigot opening for easy connection, Non return flap, capacitor operated motor complete with Induction motor suitable for 220 volts ± 10%, 50Hz ± 3 %, single phase A.C supply of class `F` insulation, easy mountings accessories in all respect with wiring upto power supply point and of following capacities and as per tender drawing: GA Drawing and technical Data sheets should be get approval before dispatch 150 CFM / 10 mm WG total St. Press. / 150 CFM (Rates are of GST excluded).

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2) 300 mm dia.(32 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2) 250 mm dia.(32 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2) 200 mm dia.(32 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2)150 mm dia.(32 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2)125 mm dia.(32 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2)100 mm dia.(32 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2) 80 mm dia.(32 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2)65 mm dia.(32 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2)50 mm dia.(32 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2)40 mm dia.(32 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2)32 mm dia.(19 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (Nitrile rubber insulation) :- `Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled / hot water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / cu m density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class `O` insulation applied by suitable adhesive or Chemically cross linked polyethlyne foam of class``O``(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc. and complete as per specifications including repairing of damage to building etc. and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.2)25 mm dia.(19 mm thick insulation) ( Rates are of GST excluded)

INSULATED CHILLED WATER PIPING (expanded polystrene insulation):- Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping plumbing inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with fire retardant quality expanded polystrene moulded pipe section of density 20 kg/cu.m after a thick coat of cold setting adhesive (CPRX compound) wrapping with 500g polythene faced hessain and finally applying 0.63mm aluminium sheet cladding complete with type3 , grade 1 roofing feltstrip(as per IS:1322 as amended up to date ) at joints repairing of damage to building etc. as per specifications and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.3) 125 mm dia. (50 mm thick insulation) - Burried Pipe from Hospital Block to OPD Block ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal and O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified (DSR:16.7.1) 250 mm dia (as per 200 mm dia size)- Decoupler line ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal and O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified (DSR:16.7.1) 200 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal and O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified (DSR:16.7.1) 150 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal and O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified (DSR:16.7.1) 125 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal and O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified (DSR:16.7.1) 100 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal and O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified (DSR:16.7.1) 80 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal and O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified (DSR:16.7.1) 65 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal and O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified (DSR:16.7.1) 50 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal and O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified (DSR:16.7.1) 40 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) Balancing valve with built in measuring facility with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation and PN 16 pressure rating for chilled / hot water pipe circulation as specified(DSR:16.7.2) 200 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) Balancing valve with built in measuring facility with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation and PN 16 pressure rating for chilled / hot water pipe circulation as specified(DSR:16.7.2) 80 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end and PN 16 pressure rating for chilled / hot water circulation including insulation as specified.(DSR:16.7.3) 200 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end and PN 16 pressure rating for chilled / hot water circulation including insulation as specified.(DSR:16.7.3) 125 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end and PN 16 pressure rating for chilled / hot water circulation including insulation as specified.(DSR:16.7.3) 80 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.(DSR:16.7.4) 200 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.(DSR:16.7.4) 125 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.(DSR:16.7.4) 80 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.(DSR:16.7.4) 65 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.(DSR:16.7.4) 50 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.(DSR:16.7.4) 40 mm dia ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.(DSR:16.7.4) 32 mm dia (as per 40 mm ) ( Rates are of GST excluded)

INSULATED VALVES:- Supplying, fixing, testing and commissioning of following valves, strainers, gauges in the chilled water plumbing duly insulated to the same specifications as the connected piping and adequately supported as per specifications.(DSR:16.7) Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified.(DSR:16.7.4) 25 mm dia (as per 40 mm ) ( Rates are of GST excluded)

INSULATED VALVES:- Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required (DSR:16.8) ( Rates are of GST excluded)

INSULATED VALVES:- Providing and fixing in position the mercury in glass industrial type thermometers.(DSR:16.9) ( Rates are of GST excluded)

INSULATED VALVES:- PRESSURE INDEPENDENT BALANCING CUM CONTROL VALVE Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. Valve shall be globe type design and the travelling stroke for the control valves will not be change, no matter the pre-setting the flow rate in the pre-setting rings.The actuator shall be capable of accepting upto 10V DC or upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm and above. Valves should have pressure rating of 16 Bar minimum. 20mm Threaded (2.5-6)USGPM ( Rates are of GST excluded)

INSULATED VALVES:- PRESSURE INDEPENDENT BALANCING CUM CONTROL VALVE Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. Valve shall be globe type design and the travelling stroke for the control valves will not be change, no matter the pre-setting the flow rate in the pre-setting rings.The actuator shall be capable of accepting upto 10V DC or upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm and above. Valves should have pressure rating of 16 Bar minimum. 25mm Threaded (6-8)USGPM ( Rates are of GST excluded)

INSULATED VALVES:- PRESSURE INDEPENDENT BALANCING CUM CONTROL VALVE Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. Valve shall be globe type design and the travelling stroke for the control valves will not be change, no matter the pre-setting the flow rate in the pre-setting rings.The actuator shall be capable of accepting upto 10V DC or upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm and above. Valves should have pressure rating of 16 Bar minimum. 32mm Threaded (8-17)USGPM ( Rates are of GST excluded)

INSULATED VALVES:- PRESSURE INDEPENDENT BALANCING CUM CONTROL VALVE Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. Valve shall be globe type design and the travelling stroke for the control valves will not be change, no matter the pre-setting the flow rate in the pre-setting rings.The actuator shall be capable of accepting upto 10V DC or upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm and above. Valves should have pressure rating of 16 Bar minimum. 40mm Threaded (17-41)USGPM ( Rates are of GST excluded)

INSULATED VALVES:- PRESSURE INDEPENDENT BALANCING CUM CONTROL VALVE Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. Valve shall be globe type design and the travelling stroke for the control valves will not be change, no matter the pre-setting the flow rate in the pre-setting rings.The actuator shall be capable of accepting upto 10V DC or upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm and above. Valves should have pressure rating of 16 Bar minimum. 50mm Threaded (41-50)USGPM ( Rates are of GST excluded)

INSULATED VALVES:- PRESSURE INDEPENDENT BALANCING CUM CONTROL VALVE Supply, Installation, Testing and Commissioning of following sizes electronic, self-balancing, pressure independent type dynamic balancing valve with integrated 2 way modualating control valve in a single body. Valve shall be globe type design and the travelling stroke for the control valves will not be change, no matter the pre-setting the flow rate in the pre-setting rings.The actuator shall be capable of accepting upto 10V DC or upto 20mA electric signal and shall provide similar transduced feedback output to control system. Maximum close off pressure shall not be less than 6 Bar for upto 50 mm valves and 7 Bar for 65 mm and above. Valves should have pressure rating of 16 Bar minimum. 65mm Threaded (50-105)USGPM ( Rates are of GST excluded)

Supplying, laying, fixing, testing and commissioning of following thickness closed cell elastrometric nitrile rubber of class `O` applied by suiatable adhesive, as per specifications and as required complete in all respect.(DSR:16.5) 32 mm ( Rates are of GST excluded)

Supplying, laying, fixing, testing and commissioning of following thickness closed cell elastrometric nitrile rubber of class `O` applied by suiatable adhesive, as per specifications and as required complete in all respect.(DSR:16.5) 19 mm ( Rates are of GST excluded)

Supply, Installation,testing and commissioning of Ball valves(full open port type) threaded type BSPT internal without Strainer complete with heavy duty PN16 bronze forged body, chrome plated bronze ball etc.and as specified in standard specification 25 mm dia ( Rates are of GST excluded)

Supply, Installation,testing and commissioning of Ball valves(full open port type) threaded type BSPT internal without Strainer complete with heavy duty PN16 bronze forged body, chrome plated bronze ball etc.and as specified in standard specification 32 mm dia ( Rates are of GST excluded)

Supply, Installation,testing and commissioning of Ball valves(full open port type) threaded type BSPT internal without Strainer complete with heavy duty PN16 bronze forged body, chrome plated bronze ball etc.and as specified in standard specification 40 mm dia ( Rates are of GST excluded)

Closed Expansion Tank alongwith Air separator with Pressurisation Pump Kit for Chilled Water Line:- Supply, installation, testing and commissioning of 1000 Ltr Closed type EXPANSION TANK along with necessary accessories such as air vents,Safety Valves, with required Support etc. The tank shall be made out of MS-2062 with replaceable heavy duty butyl rubber bladder. ( Rates are of GST excluded)

Closed Expansion Tank alongwith Air separator with Pressurisation Pump Kit for Chilled Water Line:- Supply, installation, testing and commissioning of Centrifugal Air Separator with matching flanges, bolts, nuts and gasket, with supervent, strainer, insulation, valves and fittings, 300 mm dia, PN16 etc. ( Rates are of GST excluded)

Closed Expansion Tank alongwith Air separator with Pressurisation Pump Kit for Chilled Water Line:- Tank shall be complete with Pressurization kit including Pumps required in the configuration of N plus 1 (1working plus 1 Stand By). The cost shall include necessary valve package and control logic panel (Head-25mtrs ) ( Rates are of GST excluded)

Open Expansion Tank for Hot water line :- Supply,installation,testing and commissioning of M.S. expansion tank of size 450 mm x 450 mm x 450 mm height made of 3 mm thick mild steel sheet complete with 19 mm thick nitrile rubber insulation covered with 24G Aluminium foil and complete with air vent and drain connection with valve, and control valves etc. as required. ( Rates are of GST excluded)

Supply, installation, testing and commissioning of auto air vent valve with cock or ball valve of following sizes:- 15 mm dia auto air vent valve ( Rates are of GST excluded)

Supply, installation, testing and commissioning of auto air vent valve with cock or ball valve of following sizes:- 25 mm dia auto air vent valve ( Rates are of GST excluded)

Drain Piping :- Supply and installation of Rigid UPVC piping complete with U trap, fittings, elbows, bends and supports as per specifications and duly insulated with 6 mm thick closed cell Nitril rubber with factory laminated 7 mil glass cloth or Chemically cross linked polyethlyne foam of class`O`(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc.as per specifications. 50 mm dia (Working pressure - 6Kg/cm2) ( Rates are of GST excluded)

Drain Piping :- Supply and installation of Rigid UPVC piping complete with U trap, fittings, elbows, bends and supports as per specifications and duly insulated with 6 mm thick closed cell Nitril rubber with factory laminated 7 mil glass cloth or Chemically cross linked polyethlyne foam of class`O`(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc.as per specifications. 40 mm dia (Working pressure - 6Kg/cm2) ( Rates are of GST excluded)

Drain Piping :- Supply and installation of Rigid UPVC piping complete with U trap, fittings, elbows, bends and supports as per specifications and duly insulated with 6 mm thick closed cell Nitril rubber with factory laminated 7 mil glass cloth or Chemically cross linked polyethlyne foam of class`O`(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc.as per specifications. 32 mm dia (Working pressure - 10Kg/cm2) ( Rates are of GST excluded)

Drain Piping :- Supply and installation of Rigid UPVC piping complete with U trap, fittings, elbows, bends and supports as per specifications and duly insulated with 6 mm thick closed cell Nitril rubber with factory laminated 7 mil glass cloth or Chemically cross linked polyethlyne foam of class`O`(XLPE) with Aluminium PE foil for as per given below pipe size. The joints shall be sealed with 50 mm x 1 mm thick self adhesive tape at the joints etc.as per specifications. 25 mm dia (Working pressure - 10Kg/cm2) ( Rates are of GST excluded)

CONDENSER WATER PIPE :- Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS `C` class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.10) 400 mm dia. ( Rates are of GST excluded)

CONDENSER WATER PIPE :- Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS `C` class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.10) 250 mm dia. ( Rates are of GST excluded)

CONDENSER WATER PIPE :- Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS `C` class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.10) 150 mm dia. ( Rates are of GST excluded)

CONDENSER WATER PIPE :- Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS `C` class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.10) 125 mm dia. ( Rates are of GST excluded)

CONDENSER WATER PIPE :- Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS `C` class along with necessary clamps, vibration isolators and fittings such as bends,tees etc.but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:- The Pipes of sizes 150mm and below shall be M.S. `C` class as per IS : 1239 and pipes size above 150mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above.(DSR:16.10) 100 mm dia. ( Rates are of GST excluded)

VALVES WITHOUT INSULATION :- Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications. (DSR:16.11) BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet and O - ring and PN 16 pressure rating as specified. (DSR:16.11.1) 250 mm dia.(Considered insulated valve size 200 mm dia) ( Rates are of GST excluded)

VALVES WITHOUT INSULATION :- Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications. (DSR:16.11) BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet and O - ring and PN 16 pressure rating as specified. (DSR:16.11.1) 150 mm dia. ( Rates are of GST excluded)

VALVES WITHOUT INSULATION :- Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications. (DSR:16.11) BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet and O - ring and PN 16 pressure rating as specified. (DSR:16.11.1) 100 mm dia. ( Rates are of GST excluded)

VALVES WITHOUT INSULATION :- Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications. (DSR:16.11) NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end and PN 16 pressure rating as specified. 250 mm dia. ( Rates are of GST excluded)

VALVES WITHOUT INSULATION :- Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications. (DSR:16.11) Balancing valve with built in measuring facility with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation and PN 16 pressure rating for chilled / hot water pipe circulation as specified 250 mm dia ( Rates are of GST excluded)

VALVES WITHOUT INSULATION :- Supplying, fixing, testing and commissioning of following valves, gauges and strainers for condenser water circulation as per specifications. (DSR:16.11) Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified. 250 mm dia. ( Rates are of GST excluded)

VALVES WITHOUT INSULATION :- Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required (DSR:16.8) ( Rates are of GST excluded)

VALVES WITHOUT INSULATION :- Providing and fixing in position the mercury in glass industrial type thermometers.(DSR:16.9) ( Rates are of GST excluded)

Supply, Installation,testing and commissioning of Ball valves(full open port type) threaded type BSPT internal without Strainer complete with heavy duty PN16 bronze forged body, chrome plated bronze ball etc.and as specified in standard specification 25 mm dia. ( Rates are of GST excluded)

Supply, Installation,testing and commissioning of Ball valves(full open port type) threaded type BSPT internal without Strainer complete with heavy duty PN16 bronze forged body, chrome plated bronze ball etc.and as specified in standard specification 40 mm dia. ( Rates are of GST excluded)

Supply, installation, testing and commissioning of auto air vent valve with cock or ball valve of following sizes:- 15 mm dia auto air vent valve .. ( Rates are of GST excluded)

Supply, installation, testing and commissioning of auto air vent valve with cock or ball valve of following sizes:- 25 mm dia auto air vent valve .. ( Rates are of GST excluded)

Square / Rectangular Ducting (Factory Fabricated) - (DSR:16.12.1) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 24 G (0.63 mm) ( Rates are of GST Excluded)

Square / Rectangular Ducting (Factory Fabricated) - (DSR:16.12.1) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 22 G (0.80 mm). ( Rates are of GST Excluded)

Square / Rectangular Ducting (Factory Fabricated) - (DSR:16.12.1) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 20 G (1.0 mm). ( Rates are of GST Excluded)

Square / Rectangular Ducting (Factory Fabricated) - (DSR:16.12.1) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 18 G (1.25 mm). ( Rates are of GST Excluded)

Rectangular / Square Ducting ( Site fabrication ) - (DSR:16.12.2) Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 24 G (0.63 mm) ( Rates are of GST Excluded)

Rectangular / Square Ducting ( Site fabrication ) - (DSR:16.12.2) Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 22 G (0.80 mm) ( Rates are of GST Excluded)

Rectangular / Square Ducting ( Site fabrication ) - (DSR:16.12.2) Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 20 G (1.00 mm) ( Rates are of GST Excluded)

Rectangular / Square Ducting ( Site fabrication ) - (DSR:16.12.2) Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 8 G (1.25 mm) ( Rates are of GST Excluded)

Supply, installation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications.(DSR:16.13) ( Rates are of GST Excluded)

Supplying and fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.(DSR:16.15) ( Rates are of GST Excluded)

Supplying and fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.(DSR:16.16) ( Rates are of GST Excluded)

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring and removable core.(DSR:16.17) ( Rates are of GST Excluded)

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring and removable core.(DSR:16.18) ( Rates are of GST Excluded)

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. (DSR:16.20) a) Fire damper ( Rates are of GST Excluded)

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. (DSR:16.20) Actuator ( Rates are of GST Excluded)

Duct Accoustic Lining Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. or anti-microbial Chemically cross linked polyethlyne foam of class`O`(XLPE)complete as required and as per specifications.(DSR:16.21) ( Rates are of GST Excluded)..

Duct External Insulation Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class `O`) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation or anti-microbial Chemically cross linked polyethlyne foam of class`O`(XLPE) with Aluminium PE foil complete as per specifications and as required.(DSR:16.23) 19 mm ( Rates are of GST Excluded)

Duct External Insulation Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class `O`) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation or anti-microbial Chemically cross linked polyethlyne foam of class`O`(XLPE) with Aluminium PE foil complete as per specifications and as required.(DSR:16.23) 25 mm for external duct ( Rates are of GST Excluded)

Supply, fabrication, installation and testing of Aluminium sheet metal ducting duly silicon sealed and as per tender drawings.The price shall include with supports such as full threaded rod and GI slotted channel / Wire Rope hanger including nut bolt fastner for ceiling hung and rigid Supports if laid on floor complete with end fixing in accordance with the approved shop drawings and as required by the specifications. , access door etc. 22 Gauge ( Rates are of GST Excluded)

Supplying and fixing of 18 G thick Aluminium extruded powder coated Fresh / Exhaust air weather protected louvers with bird screen type i.e. louvers blade shall be at 45° inclination with blade pitch 40 mm (with Aluminium frames if required) for ventilation. as per specification and sizes will be as per tender drawing mentioned. ( Rates are of GST Excluded)

Supplying and fixing of Non-vision air transfer grille aluminium extruded powder coated . ( Rates are of GST Excluded)

Supply, installation Testing and commissioning of wall mount differential pressusre sensor having high accuracy of plus /- 2% of measuring value(m.v.) and shall generate an output of 0-10 VDC/ 4-20 mA as output. Power supply for sensor is 24 VAC ( Rates are of GST Excluded)

HVAC Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T` irons and / or flats wherever necessary, 16 gauge CRCA sheet steel shall be used for final distribution panels. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of zinc chromate primer and final approved shade of enamelled paint. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels. All Switchboards shall have provision for entry of cables from the top or bottom as required All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all out going feeders doors and switch handles shll be lockable in off position. Space heater with thermostate and internal lighting shall be provided in all panels. GA Drawings shall be got approved before fabrication. All ACB/MCCB`s /MCB/Equipment shall be as per technical specifications Make : Schnieder/Siemens/ABB/LandT Approval shall be taken for each panel in the form of shop (GA and SLD) Drawings before fabrication. MCC -1 Main A/C Panel ( AC Plant Room) Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 50 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Incoming 1 No 1200A, FP, 50KA, EDO air circuit breaker with microprocessor based release having O/L,S/C Instantaneous and E/F protection with display of all energy parameters, Last 10 trip history. Having feature of ZSI and Terminal adaptors on Load and line side of breaker, seperate fault diffreciation indications (O/L, S/C, E/F), Ready to close, Pre overload, spring charge on panel door. i. 0-500 volts Digital voltmeter with selector switch and protection fuses. - 1 Set ii. 0- 1200A Digital Ammeter with selector switch of suitable range with three nos of CTs - 1 Set iii. 1 No. Digital KWH Meter with RS-485 cummnication port - 1 Set iv. 3 No. Phase indicating lamps with MCB`s Protection. 1 Set Main bus bar rated at 1200 amps TPN, 50 KA with heat shrinkable sleeve and shall be of aluminium. OUTGOING 03 Nos. 500 Amps MCCB as outgoing feeder for Water Cooled Screw Chiller(2W plus 1SB), over load relay with built in single phasing protection. The compartment shall contain an indicating lamp with MCB for ‘ON’ status. One as a spare. 03 Nos.40 amps MPCB with Automatic Star Delta starter for 15 HP motor, over load relay with built in single phasing protection and outgoing feeder to primary chilled water pump motor(2W plus 1SB). The compartment shall contain an indicating lamp with MCB for ‘ON’ status ofpumps motor. 03 Nos. 150 amps MCCB with Automatic Star Delta starter suitable for 75 HP motor, over load relay with built in single phasing protection and outgoing feeder to condenser water pump motor(2W plus 1SB). The compartment shall contain an indicating lamp with MCB for ‘ON’ status of pumps motor. 03 Nos.63 amps MCCB as outgoing feeder for 20 - 25 HP motor VFD, over load relay with built in single phasing protection and outgoing feeder to secondary chilled water pump motor(2W plus 1SB) for Hospital Block . The compartment shall contain an indicating lamp with MCB for ‘ON’ status of pumps motor. 02 Nos.40 amps MCCB as outgoing feeder for 15 HP motor VFD, over load relay with built in single phasing protection and outgoing feeder to secondary chilled water pump motor(2W plus 1SB) for OPD Block . The compartment shall contain an indicating lamp with MCB for ‘ON’ status of pumps motor. 1 No.100 Amps MCCB as outgoing feeder for CT`s Starter Panel at terrace, over load relay with built in single phasing protection. The compartment shall contain an indicating lamp with MCB for ‘ON’ status. 2 Nos. 450 Amps MCCB as outgoing feeder for Hot Water Generator, over load relay with built in single phasing protection. The compartment shall contain an indicating lamp with MCB for ‘ON’ status. 02 Nos.32 amps MPCB with Automatic Star Delta starter for 5 HP motor, over load relay with built in single phasing protection and outgoing feeder to Hot Water Generator pump motor(1W plus 1SB) for Monsoon Reheat. The compartment shall contain an indicating lamp with MCB for ‘ON’ status ofpumps motor. 01 Nos.25 amps MCB as outgoing feeder for ATC. The compartment shall contain an indicating lamp with MCB for ON/OFF status of pumps motor. 02 Nos.20 amps MCB with DOL starter for 3.0 HP motor of Tube Axial fan for Ventilation, over load relay with built in single phasing protection . The compartment shall contain an indicating lamp with MCB for ‘ON’ status ofpumps motor. 01 Nos.150 amps MCCB as outgoing feeder for AHU`s starter feeder Panel for Registration and Pharmacy Block vertical wing. The compartment shall contain an indicating lamp with MCB for ‘ON’ status . 01 Nos. 320 amps MCCB as outgoing feeder for AHU`s starter feeder Panel for Gynae/OBS Block vertical wing. The compartment shall contain an indicating lamp with MCB for ‘ON’ status. 01 Nos.150 amps MCCB as outgoing feeder for AHU`s starter feeder Panel for Diagnostic Deptt vertical wing. The compartment shall contain an indicating lamp with MCB for ‘ON’ status .01 Nos.200 amps MCCB as outgoing feeder for AHU`s starter feeder Panel for DEIC Deptt vertical wing. The compartment shall contain an indicating lamp with MCB for ‘ON’ status . Necessary cable alleys, wiring and G.I. earthing of all equipment shall also be provided. Note: a. Potential free contact shall be provided with necessary modbus protocol compatible to BMS and energy management system. b. All outgoing MCCB shall be Ics= 25/35/50 KA as per fault current. c. All above rating is only indicative purpose. Final rating shall be as per actual equipment selection. ( Rates are of GST Excluded)

HVAC Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T` irons and / or flats wherever necessary, 16 gauge CRCA sheet steel shall be used for final distribution panels. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of zinc chromate primer and final approved shade of enamelled paint. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels. All Switchboards shall have provision for entry of cables from the top or bottom as required All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all out going feeders doors and switch handles shll be lockable in off position. Space heater with thermostate and internal lighting shall be provided in all panels. GA Drawings shall be got approved before fabrication. All ACB/MCCB`s /MCB/Equipment shall be as per technical specifications Make : Schnieder/Siemens/ABB/LandT Approval shall be taken for each panel in the form of shop (GA and SLD) Drawings before fabrication. MCC - 2, Cooling Tower`s(CT`s) Starter Panel weather protected IP 65 Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Incoming 100 AMP MCCB TP plus NL 25 KA incoming Thermal magnetic with O/L, S/C With ROM. 1 No. VA meter and CTs of rating 100/5A. 3 Nos.phase indicating lamps. Main bus bar rated at 150 amps TPN, 25 KA with heat shrinkable sleeve and shall be of aluminium. Note: The AC contractor shall provide fire shunt relay contact in his panel wherever necessary along with auto / manual mode selector switch in the outgoing feeder for Fan to take fire input signal (Potential Free Contact).Cost shall be included in the panel price quoted by him. OUTGOING 4 Nos. 25 A TPN MPCB with Star Delta starter CT Fan`s motor, overload relay inbuilt single phase prevention, start/stop push buttons, on / off / trip indication lights with protection fuse, Auto Manual Selector switch. MPCB Shall be 10 KA All outgoing feeder shall have following accessories. 02 Nos. ON/OFF indicating lights with protection switch. Note: a. Potential free contact shall be provided with necessary modbus protocol compatible to BMS and energy management system. ( Rates are of GST Excluded)

HVAC Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T` irons and / or flats wherever necessary, 16 gauge CRCA sheet steel shall be used for final distribution panels. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of zinc chromate primer and final approved shade of enamelled paint. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels. All Switchboards shall have provision for entry of cables from the top or bottom as required All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all out going feeders doors and switch handles shll be lockable in off position. Space heater with thermostate and internal lighting shall be provided in all panels. GA Drawings shall be got approved before fabrication. All ACB/MCCB`s /MCB/Equipment shall be as per technical specifications Make : Schnieder/Siemens/ABB/LandT Approval shall be taken for each panel in the form of shop (GA and SLD) Drawings before fabrication. MCC - 3 , AHU`s starter feeder Panel for Registration and Pharmacy Block vertical wing Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Incoming 150 AMP MCCB TP plus NL 25 KA incoming Thermal magnetic with O/L, S/C With ROM. 1 No. VA meter and CTs of rating 150/5A. 3 Nos.phase indicating lamps. Main bus bar rated at 200 amps TPN, 25 KA with heat shrinkable sleeve and shall be of aluminium. Note: The AC contractor shall provide fire shunt relay contact in his panel wherever necessary along with auto / manual mode selector switch in the outgoing feeder for Fan to take fire input signal (Potential Free Contact).Cost shall be included in the panel price quoted by him. OUTGOING 07 Nos. 25 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. 01 Nos. 16 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. Note: All above rating is indicative purpose only. ( Rates are of GST Excluded)

HVAC Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T` irons and / or flats wherever necessary, 16 gauge CRCA sheet steel shall be used for final distribution panels. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of zinc chromate primer and final approved shade of enamelled paint. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels. All Switchboards shall have provision for entry of cables from the top or bottom as required All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all out going feeders doors and switch handles shll be lockable in off position. Space heater with thermostate and internal lighting shall be provided in all panels. GA Drawings shall be got approved before fabrication. All ACB/MCCB`s /MCB/Equipment shall be as per technical specifications Make : Schnieder/Siemens/ABB/LandT Approval shall be taken for each panel in the form of shop (GA and SLD) Drawings before fabrication. MCC - 4 , AHU`s starter feeder Panel for Gynae/OBS Block vertical wing Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Incoming 320 AMP MCCB TP plus NL 25 KA incoming Thermal magnetic with O/L, S/C With ROM. 1 No. VA meter and CTs of rating 320/5A. 3 Nos.phase indicating lamps. Main bus bar rated at 450 amps TPN, 25 KA with heat shrinkable sleeve and shall be of aluminium. Note: The AC contractor shall provide fire shunt relay contact in his panel wherever necessary along with auto / manual mode selector switch in the outgoing feeder for Fan to take fire input signal (Potential Free Contact).Cost shall be included in the panel price quoted by him. OUTGOING 05 Nos. 40 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. 05 Nos. 25 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. 05 Nos. 16 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. Note: All above rating is indicative purpose only. ( Rates are of GST Excluded)

HVAC Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T` irons and / or flats wherever necessary, 16 gauge CRCA sheet steel shall be used for final distribution panels. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of zinc chromate primer and final approved shade of enamelled paint. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels. All Switchboards shall have provision for entry of cables from the top or bottom as required All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all out going feeders doors and switch handles shll be lockable in off position. Space heater with thermostate and internal lighting shall be provided in all panels. GA Drawings shall be got approved before fabrication. All ACB/MCCB`s /MCB/Equipment shall be as per technical specifications Make : Schnieder/Siemens/ABB/LandT Approval shall be taken for each panel in the form of shop (GA and SLD) Drawings before fabrication. MCC - 5 , AHU`s starter feeder Panel for Diagnostic Deptt vertical wing Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Incoming 150 AMP MCCB TP plus NL 25 KA incoming Thermal magnetic with O/L, S/C With ROM. 1 No. VA meter and CTs of rating 150/5A. 3 Nos.phase indicating lamps. Main bus bar rated at 200 amps TPN, 25 KA with heat shrinkable sleeve and shall be of aluminium. Note: The AC contractor shall provide fire shunt relay contact in his panel wherever necessary along with auto / manual mode selector switch in the outgoing feeder for Fan to take fire input signal (Potential Free Contact).Cost shall be included in the panel price quoted by him. OUTGOING 07 Nos. 25 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. 02 Nos. 16 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. Note: All above rating is indicative purpose only. ( Rates are of GST Excluded)

HVAC Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T` irons and / or flats wherever necessary, 16 gauge CRCA sheet steel shall be used for final distribution panels. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of zinc chromate primer and final approved shade of enamelled paint. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels. All Switchboards shall have provision for entry of cables from the top or bottom as required All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all out going feeders doors and switch handles shll be lockable in off position. Space heater with thermostate and internal lighting shall be provided in all panels. GA Drawings shall be got approved before fabrication. All ACB/MCCB`s /MCB/Equipment shall be as per technical specifications Make : Schnieder/Siemens/ABB/LandT Approval shall be taken for each panel in the form of shop (GA and SLD) Drawings before fabrication. MCC - 6 , AHU`s starter feeder Panel for DEIC Deptt vertical wing Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Incoming 200 AMP MCCB TP plus NL 25 KA incoming Thermal magnetic with O/L, S/C With ROM. 1 No. VA meter and CTs of rating 200/5A. 3 Nos.phase indicating lamps. Main bus bar rated at 250 amps TPN, 25 KA with heat shrinkable sleeve and shall be of aluminium. Note: The AC contractor shall provide fire shunt relay contact in his panel wherever necessary along with auto / manual mode selector switch in the outgoing feeder for Fan to take fire input signal (Potential Free Contact).Cost shall be included in the panel price quoted by him. OUTGOING 01 Nos. 40 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. 03 Nos. 32 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. 04 Nos. 25 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. 04 Nos. 16 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. Note: All above rating is indicative purpose only. ( Rates are of GST Excluded)

HVAC Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T` irons and / or flats wherever necessary, 16 gauge CRCA sheet steel shall be used for final distribution panels. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of zinc chromate primer and final approved shade of enamelled paint. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels. All Switchboards shall have provision for entry of cables from the top or bottom as required All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all out going feeders doors and switch handles shll be lockable in off position. Space heater with thermostate and internal lighting shall be provided in all panels. GA Drawings shall be got approved before fabrication. All ACB/MCCB`s /MCB/Equipment shall be as per technical specifications Make : Schnieder/Siemens/ABB/LandT Approval shall be taken for each panel in the form of shop (GA and SLD) Drawings before fabrication. MCC - 7 , AHU`s starter feeder Panel for OPD Block Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Incoming 150 AMP MCCB TP plus NL 25 KA incoming Thermal magnetic with O/L, S/C With ROM. 1 No. VA meter and CTs of rating 150/5A. 3 Nos.phase indicating lamps.Main bus bar rated at 200 amps TPN, 25 KA with heat shrinkable sleeve and shall be of aluminium. Note: The AC contractor shall provide fire shunt relay contact in his panel wherever necessary along with auto / manual mode selector switch in the outgoing feeder for Fan to take fire input signal (Potential Free Contact).Cost shall be included in the panel price quoted by him. OUTGOING 07 Nos. 25 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. 03 Nos. 16 amps MCB as outgoing feeder for AHU`s VFD with bypass starter panel. The compartment shall contain an indicating lamp with MCB for ON/OFF status of AHU motor. Note: All above rating is indicative purpose only. ( Rates are of GST Excluded)

HVAC Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T` irons and / or flats wherever necessary, 16 gauge CRCA sheet steel shall be used for final distribution panels. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of zinc chromate primer and final approved shade of enamelled paint. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels. All Switchboards shall have provision for entry of cables from the top or bottom as required All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all out going feeders doors and switch handles shll be lockable in off position. Space heater with thermostate and internal lighting shall be provided in all panels. GA Drawings shall be got approved before fabrication. All ACB/MCCB`s /MCB/Equipment shall be as per technical specifications Make : Schnieder/Siemens/ABB/LandT Approval shall be taken for each panel in the form of shop (GA and SLD) Drawings before fabrication. MCC - 8,Starter Panel for Kitchen Ventilation Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 35 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Incoming 40 AMP MCCB TP plus NL 25 KA incoming Thermal magnetic with O/L, S/C With ROM. 1 No. Digital VAF meter and CTs of rating 40/5A. 3 Nos.phase indicating lamps. Main bus bar rated at 63 amps TPN, 25 KA with heat shrinkable sleeve and shall be of aluminium. OUTGOING 2 Nos. 32 A TPN MPCB with DOL starter suitable for Air Washer and Dry Scrubber Fans Motor required HP, overload relay inbuilt single phase prevention, start/stop push buttons, on / off / trip indication lights with protection fuse, Auto Manual Selector switch. MPCB Shall be 10 KA Both Outgoing starter shall be interlinked to each other so that both equipments opearte on same time. All outgoing feeder shall have following accessories. 02 Nos. ON/OFF indicating lights with protection switch. Note: a. Potential free contact shall be provided with necessary modbus protocol compatible to BMS and energy management system. ( Rates are of GST Excluded)

HVAC Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel `T` irons and / or flats wherever necessary, 16 gauge CRCA sheet steel shall be used for final distribution panels. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated with all anticorrosive process before painting as per specifications with 2 coats of zinc chromate primer and final approved shade of enamelled paint. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels. Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels. All Switchboards shall have provision for entry of cables from the top or bottom as required All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The Busbars insulation shall be with heat shrinkable sleeves.SMC/DMC shrouds and busbar supports shall be used. Padlocking facility shall be provided on all out going feeders doors and switch handles shll be lockable in off position. Space heater with thermostate and internal lighting shall be provided in all panels. GA Drawings shall be got approved before fabrication. All ACB/MCCB`s /MCB/Equipment shall be as per technical specifications Make : Schnieder/Siemens/ABB/LandT Approval shall be taken for each panel in the form of shop (GA and SLD) Drawings before fabrication. MCC - 9 and 10, Emergency Panel weather proof IP 65 - For Liftwell Pressurization for OPD and Hospital Block Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Incoming 100 AMP MCCB TP plus NL 25 KA incoming Thermal magnetic with O/L, S/C . 1 No. Analog VA meter and CTs of rating 100/5A. 3 Nos.phase indicating lamps. Main bus bar rated at 150 amps TPN, 25 KA with heat shrinkable sleeve and shall be of aluminium. Note: The AC contractor shall provide fire shunt relay contact in his panel wherever necessary along with auto / manual mode selector switch in the outgoing feeder for axial Flow Fan to take fire input signal (Potential Free Contact).Cost shall be included in the panel price quoted by him. Outgoing 7 Nos. 16 A MCB with DOL Starter for Liftwell Pressurization Fan`s Motor, start/stop push buttons, on / off / trip indication lights with protection fuse, Auto Manual Selector switch. MCB Shall be 10 KA Note: a. Potential free contact shall be provided with necessary modbus protocol compatible to BMS and energy management system. ( Rates are of GST Excluded)

Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Panel should have inside Space for VFD installation and louver for ventilation. 40 A TPN MCB with Star Delta starter Fan`s motor, overload relay inbuilt single phase prevention, start/stop push buttons, on / off / trip indication lights with protection fuse, Auto Manual Selector switch. MPCB Shall be 10 KA ( Rates are of GST Excluded)

Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Panel should have inside Space for VFD installation and louver for ventilation. 32 A TPN MCB with Star Delta starter Fan`s motor, overload relay inbuilt single phase prevention, start/stop push buttons, on / off / trip indication lights with protection fuse, Auto Manual Selector switch. MPCB Shall be 10 KA ( Rates are of GST Excluded)

Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Panel should have inside Space for VFD installation and louver for ventilation. 25 A TPN MCB with Star Delta starter Fan`s motor, overload relay inbuilt single phase prevention, start/stop push buttons, on / off / trip indication lights with protection fuse, Auto Manual Selector switch. MPCB Shall be 10 KA ( Rates are of GST Excluded)

Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. Panel should have inside Space for VFD installation and louver for ventilation. 16 A TPN MCB with Star Delta starter Fan`s motor, overload relay inbuilt single phase prevention, start/stop push buttons, on / off / trip indication lights with protection fuse, Auto Manual Selector switch. MPCB Shall be 10 KA ( Rates are of GST Excluded)

Tube Axial Fan`s Starter Panel for Emergency Smoke Exhaust Supply, Installation, testing and commissioning of Cubical type main MV panel board suitable for 3 phase, 415 volts, 50 Hz and of 25 KA rupturing capacity at 415 volts, fabricated from minimum 2 mm thick and doors of 1.6 mm thick CRCA sheet powder coated through seven tank process facility for prickling and degreasing complete with mountings, interconnections, earthing etc including mechanical and Electrical Inter locking as required. 20 A TPN MCB with DOL starter CT Fan`s motor, overload relay inbuilt single phase prevention, start/stop push buttons, on / off / trip indication lights with protection fuse, Auto Manual Selector switch. MPCB Shall be 10 KA Note: The AC contractor shall provide fire shunt relay contact in his panel wherever necessary along with auto / manual mode selector switch in the outgoing feeder for Fan to take fire input signal (Potential Free Contact).Cost shall be included in the panel price quoted by him. ( Rates are of GST Excluded)

Supplying, laying, effecting proper termination, testing and commissioning of the following POWER CABLE sizes of 1.1 KV -PVC inner sheated,extruded PVC type ST2 sheathed and Galvanised steel strips/wire as per IS 7908 (Part-I) armoured aluminium conductor cables conforming to relevant latest amended Indian Standards and aluminium lugs as per specification standard. 3.5C X 300 sq. mm ( Rates are of GST Excluded)

Supplying, laying, effecting proper termination, testing and commissioning of the following POWER CABLE sizes of 1.1 KV -PVC inner sheated,extruded PVC type ST2 sheathed and Galvanised steel strips/wire as per IS 7908 (Part-I) armoured aluminium conductor cables conforming to relevant latest amended Indian Standards and aluminium lugs as per specification standard. 3.5C X 240 sq. mm ( Rates are of GST Excluded)

Supplying, laying, effecting proper termination, testing and commissioning of the following POWER CABLE sizes of 1.1 KV -PVC inner sheated,extruded PVC type ST2 sheathed and Galvanised steel strips/wire as per IS 7908 (Part-I) armoured aluminium conductor cables conforming to relevant latest amended Indian Standards and aluminium lugs as per specification standard. 4C X 35 sq. mm ( Rates are of GST Excluded)

Supplying, laying, effecting proper termination, testing and commissioning of the following POWER CABLE sizes of 1.1 KV -PVC inner sheated,extruded PVC type ST2 sheathed and Galvanised steel strips/wire as per IS 7908 (Part-I) armoured aluminium conductor cables conforming to relevant latest amended Indian Standards and aluminium lugs as per specification standard. 4C X 25 sq. mm ( Rates are of GST Excluded)

Supplying, laying, effecting proper termination, testing and commissioning of the following POWER CABLE sizes of 1.1 KV -PVC inner sheated,extruded PVC type ST2 sheathed and Galvanised steel strips/wire as per IS 7908 (Part-I) armoured aluminium conductor cables conforming to relevant latest amended Indian Standards and aluminium lugs as per specification standard. 4C X 16 sq. mm ( Rates are of GST Excluded).

Supplying, laying, effecting proper termination, testing and commissioning of the following POWER CABLE sizes of 1.1 KV -PVC inner sheated,extruded PVC type ST2 sheathed and Galvanised steel strips/wire as per IS 7908 (Part-I) armoured aluminium conductor cables conforming to relevant latest amended Indian Standards and aluminium lugs as per specification standard. 4C X 10 sq. mm ( Rates are of GST Excluded)

Supplying, laying, effecting proper termination, testing and commissioning of the following POWER CABLE sizes of 1.1 KV -PVC inner sheated,extruded PVC type ST2 sheathed and Galvanised steel strips/wire as per IS 7908 (Part-I) armoured aluminium conductor cables conforming to relevant latest amended Indian Standards and aluminium lugs as per specification standard. 4C X 6 sq. mm ( Rates are of GST Excluded)

CONTROL CABLE Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel / PVC conduit as required(DSR- 1.17.4) 4C X 1.5 Sq.mm ( Rates are of GST Excluded)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (DSR:9.1) 3.5C X 300 sq. mm ( Rates are of GST Excluded)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (DSR:9.1) 3.5C X 240 sq. mm ( Rates are of GST Excluded)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (DSR:9.1) 4C X 35 sq. mm ( Rates are of GST Excluded)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (DSR:9.1) 4C X 25 sq. mm ( Rates are of GST Excluded)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (DSR:9.1) 4C X 16 sq. mm ( Rates are of GST Excluded)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (DSR:9.1) 4C X 10 sq. mm ( Rates are of GST Excluded)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. (DSR:9.1) 4C X 6 sq. mm ( Rates are of GST Excluded)

Earthing Strip / Wires. Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. (DSR:5.15) ( Rates are of GST Excluded)

Earthing Strip / Wires. Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. (DSR:5.16) ( Rates are of GST Excluded)

Cable Tray Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts and nuts, painting suspenders etc as required. (DSR:4.1) 100 mm width x 50 mm depth x 1.6 mm thickness ( Rates are of GST Excluded)

Cable Tray Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts and nuts, painting suspenders etc as required. (DSR:4.1) 150 mm width x 50 mm depth x 1.6 mm thickness ( Rates are of GST Excluded)

Cable Tray Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts and nuts, painting suspenders etc as required. (DSR:4.1) 200 mm width x 50 mm depth x 1.6 mm thickness ( Rates are of GST Excluded)

Cable Tray Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts and nuts, painting suspenders etc as required. (DSR:4.1) 300 mm width x 50 mm depth x 1.6 mm thickness ( Rates are of GST Excluded)

Cable Tray Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts and nuts, painting suspenders etc as required. (DSR:4.1) 450 mm width x 50 mm depth x 2 mm thickness ( Rates are of GST Excluded)

Cable Tray Supplying and installing following size of perforated pre-painted M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts and nuts, painting suspenders etc as required. (DSR:4.1) 600 mm width x 62.5 mm depth x 2 mm thickness ( Rates are of GST Excluded)

Supplying, installation, testing and commissioning of CTI Certified induced draft Counter Flow ( CTI STD 201 ) FRP Cooling Tower suitable for heat rejection of water-cooled screw chiller capacity 425 TR (1285200 kcal/hr) each in multi cell casing construction with water basin made out by FRP material, PVC fills with louvers and drift eliminators complete with hot water distribution system should be Gravity Flow comprising of static header and branch arms system, statically and dynamically balanced axial flow type fan-direct driven with TEAO/TEFC induction motor type IE3 weather protected suitable for 415 ± 10% 50 Hz , 3 Phase A/c supply, operating at low noise level, suction screen, make and up-quick fill arrangement, overflow, drain connections and suitable inspection ladder, access arrangement for cooling tower interior, steel/masonry supporting structure, anti-vibration mountings, complete as per specifications and as required. GA Drawing and Technical Data sheets should be got approved before dispatch Location: Fatehabad (Haryana) Inlet Water Temperature 36.4 °C (97.5°F) Outlet Water Temperature 32.2 °C (90.0°F) Water flow rate - Not to exceed 4 USGPM / TR Approach:- Min. 5.4°F The performance required for the cooling tower is a minimum 60 gpm/hp as per Ashrae 90.1/ 6.8.1-7. Both Working (Rates are of GST excluded).

SUPPLY OF CHILLERS Chillers package-Water cooled screw Chiller with VFD AHRI certified Water chilling machine with Semi-hermetic/ open type centrifugal compressor, refrigerant cooled motor, Even Pass flooded type insulated chiller, Even Pass Water cooled shell and tube condenser with Higned marine box, integral refrigerant piping, automatic controls and accessories etc. all mounted on steel frame as per specifications. Motor shall be of high efficiency suitable for 415 plus 10% volts, 50 plus 3%Hz, 3 phase AC supply, controls shall be suitable for hookup to BMS, compatible with BacNet/ Modbus. Chiller shall be complete with Unit Mounted Air Cooled VFD with minimum IP42 protection (Variable Frequency Drive). List of approved make: Trane/ Daikin/ York/ Climaveneta(Mitsubishi)/ Voltas (Country of Origin: US/Europe/India). Manufacturer shall have own service step in India from past 10 years. Company with third party service not acceptable. Bidder shall submit AHRI certified sheets at the time of submission. a. Chiller shall be able to unload from 100% to 25% at AHRI reducing temp. Chiller shall come with complete first charge of refrigerant and oil from factory only. b. Chiller shall have Micro-processor based controls with alpha-numeric display in English for all operating parameters such as supply voltage, frequency, load current, chilled water inlet, chilled water outlet, condenser water inlet and outlet temperature and operating presuure etc. flange at the Chiller/ Condenser inlet and outlet shall be supplied along with chiller package. Chiller shall have Sight glass and liquid line isolation valve as mandatory features. Oil cooling shall be as Water Cooled/ Refrigerant Cooled. c. Elect. control panel The electrical control panel shall be factory fabricated, preferably unit mounted or free standing type complete with suitable rated power disconnect switch/ MCCB and a VFD complete with all safeties, interlocks and protections such as over load, short circuit and single phasing prevention. Chiller operating parameters shall be: Chilled Water IN 54 F (12.22 C), Chilled Water out 44 F (6.66 C) Evaporator Pressure Drop 12 Ft Condenser water In 90 F (32.22 C) Condenser water out 97.5 F (36.38 C) Condenser Pressure Drop 21 Ft Chiller Fouling Factor 0.0005 FPS Condenser Fouling Factor 0.001 FPS Referigerant R134a only Working pressure* 150 PSI 1KW/TR 0.64 COP Not less than 6.2 at ARI IPLV 9.7 above NPLV 9.4 above 425 TR plus 3% actual capacity water chilling machine as described above and at above mentioned operating conditions. The price of water chilling machine including with loading, unloading, lifting and shifting etc at site positioning. (02 working plus 01 standby) (Rates are of GST Excluded)