Public Works Department Tender

`Providing and Placing in position 2 Seater Sofa for HOD Cabin. Upperstructure shall be a single shell 1.2 ±0.1cm. thick hot pressed plywood. Dia 4mm zig-zag type assembly is mounted in the understructure for support and additional cushioning purpose. The seat is made up of PU foam with density 32 plus /-2 Kg/m3 having an additional top layer of PU foam with density 28 plus /-2 Kg/m3, upholstered with fabric or leatherette. The back is made up of 28 plus /-2 Kg/m3 with additional top layer of PU foam with density 23 plus /-2 Kg/m3, upholstered with fabric or leatherette. The leg is a welded assembly made up of stainless steel (grade SS 202) tube and plate. Overall Dimensions of Chair shall be Seat Height - 45.0 cm, Height - 82.0cm, Width and Depth of Chair as measured from pedestal - Width-146.0 cm and Depth-92.0 cm.

Providing and Placing in position Main Table. Overall size of the table shall be 1800 W mm x 1650 D mm x 750 H mm. Worktop shall be made of Made of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Side table shall be Made of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel shall be made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Cube legs shall be fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) shall be welded for fixing worktop. These shall be welded together by argo shield welding. This welded structure shall be coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert shall be fixed, on to which a straight M8 leveler fitted which allows for adjustment of the height upto 50mm. Cross Members shall be made from 50mm X 25mm X 1.2mm thick ERW tube (as per IS:7138). These shall be coated with 50 micron epoxy polyester coating. Cross Members shall be assembled by friction fit PDC joinery and grub screws. There shall always two cross members for one table. Soft closing access flap shall be used. Provision for standard size of 8 module electrical shall be offered. Access flap shall be made from Aluminum extrusion, PDC parts made from Aluminum Alloy and plastic parts are made from Nylon 6 and wire brush with nylon bristles. Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8 Module cutout provision). This shall be fixed with worktop along the depth at Access Flap position. Hinge Door Unit shall be made of 18mm Thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Door shall be fixed with slide on hinges and handle is provided for ease of opening. Drawer shall be provided with ebco metabox slide and lock for security.

Providing and Placing in position High Back Chair. The seat shall be made up of 1.2 plus /-0.1 cm thk hot pressed plywood. The Back shall be made up of injection moulded glass filled nylon and upholstered using Micro mesh fabric with high tenacity yarn with 28 density foam Sandwich in lumbar area. SEAT SIZE shall be 47.0 cm. (W) x 51.5 cm (D) and BACK SIZE shall be 45.0 cm. ”(W) x 65.3 cm. (H). The HR polyurethane seat foam shall moulded with density 45 plus /-2 kg/m` and hardness 16 plus 2 kgf as per IS:7888 for 25% compression. The adjustable armrest shall be designed with the folIowing features: • Up-Down adjustment— 8 steps (8.0 plus 0.Scm range), • Height adjustable armrest structure which is Powder Coated and fitted with an armrest top, • Fixed Armrest Top is PU moulded over metal insert. The adjustable tilting mechanism shall be designed with the following features: • 360° revolving type, • Single point control, • Front-pivot for tilt with feet resting on ground ensuring more comfort, • Tilt tension adjustment, • 4-position locking with anti shock feature, • Seat/back tilting ratio of 1:2. The Neckrest assembly consist of polypropylène pad with moulded polyurethane foam and covered with polyester fabric. Neckrest shall be fixed to Back Assembly through Neckrest connector. Neckrest assembly shall have height adjustment of 4.2 plus 0 5 cm and rotation adjustment of overall 76 plus /- 2 degree. The complète neckrest assembly shall be retro fit to the main chair. The pneumatic height adjustment shall have an adjustment Stroke of 10.0 plus /-0.3 cm. The pedestal shall be injection moulded in black 33% glass-filled Nylons and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 66.1 plus /-0.5 cm. (76.1 plus /-1.0 cm. with castors). The Coat Hanger shall be made up of injection moulded glass filled nylon. The Coat hanger shall be retro fit and is fixed to the back assembly. The twin wheel castors shall be injection moulded in black Nylon.

Providing and Placing in position Table for Doctor. Overall size of the Table shall be 1350 W mm x 600 D mm x 750 H mm. The top and modesty panel shall be made of 25 mm thick pre-laminated twin board of E1-P2 grade, edge banded with 2 mm thick PVC lipping. Table top shall be provided with Gromet on work surface for wire management. The understructure shall be made of 25 mm thick Pre-laminated twin board of E1-P2 grade, edge banded with matching 2 mm thick PVC lipping. Hinge Doors shall be made of 25 mm thick pre-laminated twin board of E1-P2 grade, edge banded with 2 mm thick PVC lipping. Handle shall be provided for ease of opening. Storage shall be provided with cam lock for security.

Providing and Placing in position Reception Chair. The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood and shall be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of powder coated (DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The dimensions of back shall be 46.5 cm (W) x 60.5 cm (H). The HR polyurethane foam shall be moulded with density =45 plus /-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black Co-polymer Polypropylene. The mechanism shall be designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be 3 piece telescopic type and injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to max 54.3cm, Height - min89.5 to max 100.5cm, Width and Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.

Providing and Placing in position Visitors Chair. The cushioned seat assembly shall be made of injection molded plastic inner and outer. Plastic inner shall be upholstered with foam laminate fabric and moulded high resiliance polyurethane foam of density 45 plus /-2 per cubic metre and hardness load of 16 plus /-2 Kgf. Seat size shall be 46 cm W x 48 cm D. Thecushioned back shall be made of PU foam with insitu molded MS ERW round tube of size 1.9 plus /-0.03 x 0.16 plus /-0.0128 cm. it shall be upholstered with foam laminate fabric. Back size shall be 46.6 cm W x 59.6 cm H. The powder coated tubular frame shall be cantilever type and shall be made of 2.54 plus /-0.03 x 0.2 plus /-0.016 cm thick MS ERW tube. The back shall be connected to the frame through powder coated high pressure die cast connector piece.

Providig and Placing in poition Waiting Chair. The seat shell shall be a welded assembly of seat,back and side frame. The seat and back shall be made of 0.12±0.013cm thk CR steel sheet with oblong perforations.They shall be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk HR steel. The welded assembly shall be powder coated ( DFT 40-60 microns). The seat shall has a front water fall edge to provide popliteal clearance for comfortable seating. It also shall has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. Clean and flat surfaces of seat and back shall aids in easy maintenance. The dimensions of seat shall be 47.8 cm (W) x 44.6 cm (D) and of back shall be 41.6 cm (W) x 23. cm (H). Understructure assembly shall consists of connecting beam and leg assembly made of M.S.E.R.W. oblong tube of size 7.5±0.03cm x5.0±0.03cm x 0.02±0.016cm thk.The welded structure assembly shall be powder coated (DFT 40-60 microns ).The leg assembly shall be fitted with shoes and levellers in Nylon. The leg structure shall be designed with minimal area of contact close to ground providing easy access for cleaning purposes. The shoes fiited to leg assembly shall help in aligning the structure for back to back arrangements. Levelers should take care of uneven flooring .Connecting beam shall be fitted with snap locking end cap.It also aids in side-by-side understructure alignment. Armrest assembly shall consists of armrest frame and armrest pad. The armrest frame shall be made up of size 3.175±0.05cm x 0.47±0.027cm thk HR steel and it shall be powder coated (DFT 40-60 microns). Armrest pad shall be injection molded in Nylon and shall be fitted onto the armrest frame. Overall Dimensions shall be Seat Height - 44.1 cm, Height - 78.5 cm, Width and Depth of Chair as measured from pedestal - Width-169.5cm and Depth-63.8 cm.

Providing and Placing in position Main Table. Overall size of the table shall be 1500 W mm x 1500 D mm x 750 H mm. Worktop shall be made of Made of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Side table shall be Made of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel shall be made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Cube legs shall be fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) shall be welded for fixing worktop. These shall be welded together by argo shield welding. This welded structure shall be coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert shall be fixed, on to which a straight M8 leveler fitted which allows for adjustment of the height upto 50mm. Cross Members shall be made from 50mm X 25mm X 1.2mm thick ERW tube (as per IS:7138). These shall be coated with 50 micron epoxy polyester coating. Cross Members shall be assembled by friction fit PDC joinery and grub screws. There shall always two cross members for one table. Soft closing access flap shall be used. Provision for standard size of 8 module electrical shall be offered. Access flap shall be made from Aluminum extrusion, PDC parts made from Aluminum Alloy and plastic parts are made from Nylon 6 and wire brush with nylon bristles. Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8 Module cutout provision). This shall be fixed with worktop along the depth at Access Flap position. Hinge Door Unit shall be made of 18mm Thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Door shall be fixed with slide on hinges and handle is provided for ease of opening. Drawer shall be provided with ebco metabox slide and lock for security.

Providing and Placing in position Main Chair. The cushioned seat assembly shall be consisting of seat base moulded in glass-filled poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyster fabric. The cushioned back assembly shall be consisting of back inner moulded in Poly-propylene in-situ moulded with polyurethane and upholstered with high stretch knittedpolyster fabric. The back size shall be 45.5 cm x 53 cm H and the seat size shall be 48.5 cm W x 49.0 cm D. The hig hresiliance polyurethane foam used in the seat and back cushion shall be moulded in density 45 plus /- 2 kg/m³ and hardness load shall be 16 plus /- 2 kgf for 25% compression. The seat and back shall be firmly connected to the frame and shall be cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need of complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with back movement during posture changes. The `S` shaped spines moulded in high strength glass-filled poly-amide and the spine connector moulded in glass -filled poly-amideform the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 positions tilt limit feature which is inbuilt in seat base and the tension shall be user weight dependent. The armrset assembly shall be made of housing sliding over the armrest struture, both moulded in glass-filled polyamide. The height djustment feature shall be button operated having adjustment stroke of 6.6±0.5 cm. The armrest top shall be made of integral skin PU moulded over plastic inner moulded in glass filled polyamide. The seat height can be adjusted with the pneumatic gas-lift having an adjustment stroke of 9.2 plus /- 0.3 cm. The pedestal shall be injection moulded in glass-filled poly-amide and fitted 5 nos. of twin wheel castors The pedestal shall be 66 plus /- 0.5 cm pitch center dia. and 76 plus /- 1 cm with castors. 5 nos. of twin wheel castors shall be injection moulded in poly-amide having 5.0 plus /- 0.1 cm wheel diameter and assembled with pedestal.

Providing and Placing in position Patient Stool. Overall Dimension: Overall Sizes Diagonal Leg Dia 538 mm H470 min-655maxTop plate should made of SS 202 made sheet with spin section of thickness 1mm and should be non corrosive. It should have a diameter of 305mm,seat base should made of MS ring and rectangular tube.EN8 Screw having dia of 22 mm should be used for height adjustment of the seat base.The round hub should be made of MS ERW tube having dia of 38mm and thickness 2 mm. The Hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.The understructure should consist of 4 legs made up of MS ERW tube of diameter 25.4 mm and 1.6mm thick. The press formed pipe leg should give a round and clean look. All the legs should be provided with 4 nos of Nylon-6 bush.All metal components should be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbial epoxy polyster powder coating to fulfill the requirements for bacterial protection against at least 2 commonly found bacteria in Hospital environment [Gram positive and Gram Negative].Safe working load must be 135kg.

Providing and Placing in position Examination Table. Overall size of the table shall be 1830 mm L x 600 mm D x 850 mm H. The examination table shall be made of sturdy structure and shall have a ratchet mechanism for tilting the backrest. Leg frame and intermediate frame shall be made of 30x30 section 1.6 mm thick M.S. ERW Tube. Nylon 6 leg shoe shall be provided to avoid wear and tear of the floor. Lying surface shall be made of 1.2 mm thick M.S. ERW Tube. Ratchet shall be made of 5 mm thick M.S. ERW tube and shall provide back tilt at 0º, 15º and 30º asjustment positions. Table shall be epoxy polyxter powder coated and shall have a maximum load bearing capacity of 135 kgs. It shall be provided with 30 mm thick mattress. Providing and Placing in position Single Step Stool. Overall size of the stool shall be 485 W mm x 355 D mm x 210 H mm. It shall be a sturdy stool for supporting patients while accessing the examination table. Understructure frame shall consist of 4 MS 1.2 mm thick Vertical tubes of 19mm Dia, 3 horizontal tubes at the bottom and 3 tubes at the top to support the sheet metal top. Stool top shall be made of 2 mm thick MS sheet for standing purpose. 3 Nos. of 4 mm thick aluminium extrusions strips shall be placed on the sheet metal top for getting a good grip while climbing. Max load bearing capacity shall be 135 Kgs.

Providing and Placing in position Plain Almirah. Overall size of the Almirah shall be 916 mm (W) x 486 mm (D) x 1980 mm (H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It shall have 4 no.s full shelves. A4 size box file(85 W x 285 D x 345 H mm) can be stored vertically on three shelves and the clear space above fourth shelf is 240mm. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns ( plus /- 10). There shall be 5 loading levels in the almirah.

Providing and Placing in position Modular Storage Unit. Overall size of the unit shall be 1800 W mm x 450 D mm x 1950 H mm. It shall be aesthetically appealing completely knock down construction. The add-on units are stack widthwise to form arow of storage. Legs fitted with screw type leveler. It shall be made from combination of Top panel(0.5mm CRCA), side panel(0.5mm CRCA), Bottom panel(0.5mm CRCA) Back panel(0.5mm CRCA), Top Bottom stiffener(1.2mm CRCA) and End Cover(0.5mm CRCA). Shelves shall be a 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513) Each shelf has max Load Capacity of 30kg UDL with 4 Nos. of fixed shelves. A4 size Box file (85Wx340Hx285D) can be stored vertically on all loading levels. Doors shall be made of 0.6mm Thick CRCA (D Grade, IS-513) with Soft closing Hinges. Handles shall be Asthetically appealing handle made of Aluminum. It shall be having 3 Way locking provision, with Click action mechanism, with Key removable in locked and unlocked positions. Zinc alloy die cast housing. The unit shall be Epoxy Polyester Powder coated to the thickness of 50 microns ( plus /-10 micron).

Providing and placing of panel and tile based modular workstations which are GRIHA compliant and as per BIFMA standards, with partition thickness of 50 mm thick including powder coated aluminium trims and supported on Legs for better air circulation and helps in keeping floor clean. The product should be complete and as per apprroved sample and as per the direction of Engineer-In-charge. Panels Construction - Each panel consists of Vertical extrusions 2Nos and Horizontal extrusions made of 1.2mm thick aluminium with duly powder coated at every division of tile/block. Each panel have Bottom frame fabricated for 50 mm panel comprises of L-channels made of 2mm thick CRCA steel (IS: 513), formed plates of 3mm thick HR steel (IS: 2062) and ERW steel tube of size 35x15x1.6mm thick in oval cross section (IS: 7138) welded together. The complete bottom frame shall be powder coated with an average of 50-60 microns thickness of epoxy powder coating. The Bottom Frame is bolted with the Upright verticals. Each Panel is provided with 2Nos Legs of height 120mm are fixed at the bottom frame of the panel. Legs are fabricated by CO2 welded MS Tube of section 38mm x 25mm (IS: 7138 ERW Tube, 38mm x 25mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5mm HR) over which an M8 Leveler is fitted which allows for adjustment of the height by 50mm. It will be coated with 45-50micron thickness of epoxy powder coating. Each Panel consists of 2Nos Intermediate blocks. In a 52.4mm Thick panel intermediate block shall comprise of 38mm thick paper honeycomb with 3mm MDF on each sides and 0.6mm decorative laminate on both sides. Particle board framing shall be used n outer boundary of these blocks as well as intermediately at certain locations forming conduit for passing cables. These blocks will be located in the middle bands of the panels made out of a composite construction of MDF and paper honeycomb. Each Panel consist of TOP TILES/SPLIT TILES. These tiles shall be slide in to the panels from top before fixing the top horizontal. These tiles shall be supported from top and bottom side with clips made from PP co polymer fitted in horizontal extrusion. In case of split tiles it shall be offered in Fabric magnetic tiles, Whiteboard tiles. Each Panel consists a BOTTOM TILE. These bottom tiles shall be press fitted on to the assembly frame of the panel with the help of snap on clips made of nylon-66 and support clips made from PP polymer. All partitions and side panels have levelling screws for adjustment in case of Uneven floor to take care of plus /- 40 mm of uneven flooring. `Tile Finishes :a FABRIC MAGNETIC TILES: Fabric magnetic tiles shall be fabric upholstered metal tiles in 0.6 mm thick G.I. Grade O as per IS: 277. The fabrics shall be upholstered with adhesives. • FABRIC TACK TILES: Fabric tackable tiles shall be upholstered metal tiles in 0.6mm thick G.I. grade O as per IS: 277, with P.E. foam in the tile for tackablity. The fabric shall be upholstered with adhesives. • WHITE BOARD TILES : White board tiles shall be made of 8.0 mm thick particle board conforming to IS: 12823 laminated with 0.6mm thick white glossy high pressure laminate on outer side and 0.6mm backing laminate on inner surface and will be having all its edges with minimum 0.5 mm thick PVC edging. ` End/Intermediate Panels : It is a 22.8mm Thick panel used at the ends and as a intermediate panle between 2 adjacent workstations. It is conncted to the main panel using screws and provided with trims on the outer edges. `Aluminium Trims : The top trims and end trims for 52.4 mm shall be made from aluminum extrusion. All kinds of extrusions for 52.4mm shall have average wall thickness of 1.2 mm and having finish of powder coating. Top trim in 52.4mm thick panel shall be press fitted on the horizontal extrusion, it shall be slide fitted with the help of top trim connector made from PP copolymer 3530 grade. End trim for 52.4mm thick panel shall be slide fitted with the help of end trim connector made from 2.0mm thick M.S. CRCA Grade D as per IS: 513. End trim for 22.8 mm thick panel shall slide with the help of end trim connector made from nylon-66.` `Wire Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the panels through concealed conduits inside the blocks. Wires runs through the system from Bottom tile and extended to the top at various locations by the help of 2 nos. vertical Cable Ducts in each panels. Cable duct shall be made from 0.8 mm thick M.S. CRCA Grade D as per IS: 513 - 1994. It is constructed with two parts, one is body and another is cover. It holds the cables and gives aesthetic appearance by covering all cables entry, which are moving upward to the panels. Size of Cable duct is 107mm W X 154 mm H X 21 mm D.` Legs - Metal powder coated legs at the end. System shall also have 120 mm high powder coated standalone panel legs to give the system an elevated look. Single side legs are fabricated by CO2 welded MS Tube of section 38 mm x 25 mm (IS: 7138 ERW Tube, 38 mm x 25 mm x 16bg) with the base plate of the MS plate of 35x22x5mm (IS: 2062, 5 mm HR) over which an M8 Leveler is fitted Worksurface : Worktop shall be made out of 25mm thick prelaminated particle board. All the open edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The work surface shall be provided with circular cut out of Dia.65mm as per the requirement, for passing of wires. These cut outs shall be provided with ABS covers. Worksurfaces are fitted to the panels by worksurface brackets. Brackets are made of 2.0mm thick CRCA grade D steel as per IS : 513. Brackets are slide in between end trim and vertical extrusions. Mobile Drawer : Mobile Drawer Unit having 3 Drawers Unit having flat metal front and top with Central locking. The Drawer Unit consistes of 2Box and 1File Drawers. The Overall size of the Drawer Units is 450mm(W) X 435mm(D) X 646mm(H). Construction and Material of Drawer Unit : Welded Assembled of 0.8 thick CRCA for Body Shell, Drawer Front and tray, Front Side Stiffener, Rear Side Stiffener and Bottom, 1.2 thick CRCA Top Stiffener and Bottom stiffener. Drawer Fronts and Metal Front Straight Edge. All Drawers with Double extension precision ball slide shall be provided. For Drawer pulling, side wise tapered recess provided in shell behind Drawer Fronts. Locking:10 lever Cam Lock and Central Right Hand locking with actuator and lock channel mechanism. Top Panel : 0.8 Thick Metal Straight Edge Top. Castors : Swiveling non-lockable 4Nos Castors mounted below the body shell. The Total drawer unit is finished with Epoxy Polyester Powder coated to the thickness of 50 microns ( plus /-10). Key Board Pullout Tray : Supplying and Fixing of sliding computer key board tray of 480mm (L) X 280mm (D) X 40mm(H) made out of CRCA steel as per IS : 513 made of 0.9mm thick powder coated with sliding channels and other fixing fittings. It should also have a sliding system for accomodating mouse. CPU Trolley : Supplying and Fixing of CPU Trolley of Size - 345mm(W) x 226(D) x 180mm(H) is made of 1.0 mm thick MS CRCA Sheet and Side support is made of 0.8 mm thick MS CRCA Sheet. It consists of 4Nos Non-lockable twin wheel castors made of injection moulded in Black Nylon. Recta - 1200 W mm x 600 D mm x 1200 H mm

Providing and Placing in position 2 Dr. Locker for Students. Overall size of the unit shall be 370 mm (W) x 450 mm (D) x 1900 mm(H). It shall be made from combination of Top panel(0.5mm CRCA), side panel(0.5mm CRCA), Bottom panel(0.5mm CRCA) Back panel(0.5mm CRCA), Top Bottom stiffener (1.2mm CRCA) and End Cover(0.5mm CRCA). Shelves shall be a 12 bend panel made of 0.7mm Thick CRCA (D Grade, IS-513). Locking shall be cam lock with 3 way locking provision, with click action mechanism and shall have zinc alloy die cast housing.

Providng and Placing in position Optimisers. Size: Overall Dimensions of a body shall be 1200 mm (W) x 400 mm (D) x 2000 mm (H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel. Each configuration have following type of blocks – Single Static (SS), Single Last (SL),Twin Mobile(TM). Finish: Finish shall be Epoxy polyester powder coated thickness of 40 microns. Construction: Shelf construction shall be made from CRCA steel 0.8 mm. Uniformly distributed load capacity of 100 Kg. Undercarriage: Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick. Movement: The Movements shall be Push-Pull / Drive Type configuration. Locking: Fittings shall be centralized locking arrangement through locking stiffener mounted onto back of single last unit so that it gets locked on channels when all the units are brought together. The Recess handle lock is placed at suitable height .The ‘sprocket-chain’ arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the body. Fixed unit (SD) does not have the Handle. Each units shall have Locking Knob for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The nuts and bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 15 for SD3. Label holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. Rail Pair: It consists of ‘C’ section 2 mm thk HR sheet and Square 25.4mm X 2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the help of raul plug and screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm, 1600mm and 2400mm.

Providing and Placing in position 1$ Seater Meeting Table. Overall size of the Table shall be 3000 W mm x 1150 D mm x 740 H mm. Top shall be made of 25 mm thick Pre-laminated twin board, edge banded with matching PVC edge lipping. Access panel shall be provided with soft closing hinges. The understructure shall consist of 25 mm thick * 18 mm thick pre-laminated twin board, edge banded with 2 mm thick matching lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. A wire raiser made of 0.8 mm thick CRCA shall be provided. It shall be epoxy polyster powder coatedc(DFT 40-60 microns) for flow of wires and cables.

Providing and Placing in position Meeting Chair. The seat shall be made up of 1.2 ±0.1cm thick hot pressed plywood. The back is made up of injection moulded glass filled nylon and upholstered using net fabric with high tenacity yam. The dimensions of seat should be 47.0cm(W) x 51.5(D) and that of back should be 45.0cm(W) x 65.3cm(H). The moulded polyurethane foam shall be of density 55 plus /-2kg/m ³, and hardness load 16 plus /-2kgf as per IS:7888 for 25% compression. The armrests have up and down adjustment of 8.5 plus /-0.5 cm with top having integrated layer of Thermoplastic Elastomer(TPE). The lumbar support consists of polypropylene pad with moulded polyurethane foam covered with polyster fabric. The lumbar pad has adjustment of 8.0 plus /-0.5 cm. The mechanism of the chair shall have following features : 360° revolving type, Single point control, Tilt tension adjustment, 4 position locking with antishock feature, seat back tilt ratio 1:2, front pivot for tilt with feet resting on ground ensuring more comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 plus /- 0.3 cm. The pedestial shall be injection moulded in black 33% glass-filled Nylon-66. It shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be 66.1 plus /- 0.5 cm pitch-centre-dia (76.1 plus /- 1.0 cm with castors). The twin wheel castors shall be made of Nylon injection moulded in black Nylon. Overall dimensions of Chair shall be, Width of Chair - 76.1cm, Depth of Chair - 76.1 cm as measured from pedestal below. Height of back from ground - min 98.0 to max 108.0cm. Seat height - min 44.0 to max 54.0cm.

Providing and Placing in position Canteen Table. Overall size of 1180 W mm x 1580 D mm x 750 H mm. Top shall be of Stainless Steel brushed with PLB insert for Durability. Easy to maintain hygiene. The Understructure shall be made of 50.8 mm x 50.8 mm 1.2 mm thick powder coated ERW tubes at base which are welded and fixed to the Top with screws. Tubular stiffeners that are provided between the two vertical frames. The tubes shall be closed with plastic cap. The seats are offered in SS round stool types. Level adjustment shall be provided to take care of unevenness in floor.

Providing and Placing in position 3 Seater Sofa for Waiting Room. The side frame assembly shall be fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It shall be made of 0 3.81 ±0.03cm. x 0.2±0.016cm. thick cmx0.l6cm and black powder coated (DFT 40-60 microns). The ends shall be fitted with ABS moulded end caps. It shall be the connecting beam assy. which holds the two side frames to each other. 2 nos tie members shall be used to connect the side frames. The tie-member shall be of dia 3.81 ±0.03cm x 02±0.016cm. thick cm x 0.16cm and black powder coated (DFT 40-60 microns ). The seat/back assemblies shall be mounted on one of the tie-member which shall has 5.0 ±0.1cm x 5.0 ±0.1 cm x 0.5±0.1cm. thk 5.5 ±0.1cm Long MS. Std. angles welded to mount the seat and back. The seat rest assembly shall be consists of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45 plus /-2 Kg/cm3 with Hardness load=25±2kgf as per lS:7888 for 25% compression of the foam. The complete moulded seat rest assembly shall be covered with a replaceable fabric upholstery cover. The dimensions of seat shall be: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T). The backrest assembly shall be flexing type and consists of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density = 45 plus /- 2 Kg/cm3 with Hardness load 14± 2 kgf as per lS:7888 for 25% compression of the foam. The complete moulded backrest assembly shall be covered with a replaceable fabric upholstery cover. The size of the back shall be 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) The adj. glide shall be injection moulded in black Nylon and fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take care or unleveled floor surface. Overall Dimensions of Chair shall be Seat Height - 43.5 cm, Height - 78.5cm, Width and Depth of Chair as measured from pedestal - Width-164.0cm and Depth-70.0 cm.

Providing and Placing in position Centre Table. The top shall be made of which shall be 12 plus /-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12 plus /-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

Providing and Placing in position Corner Table. The top shall be made of glass which shall be 12 plus /-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12 plus /-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.

Providing and Placing in position Table for HOD / Incharge. Overall size of the Table shall be 1800 W x 900 D x 750 H and ERU 1200 W x 500 D x 750 H. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing and anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Providing and Placing 2 Seater Sofa for Incharge / HOD Cabin. Upper structure shall be a single shell 1.2 ±0.1cm. thick hot pressed plywood. Dia 4mm zig-zag type assembly is mounted in the understructure for support and additional cushioning purpose. The seat is made up of PU foam with density 32 plus /-2 Kg/m3 having an additional top layer of PU foam with density 28 plus /-2 Kg/m3, upholstered with fabric or leatherette. The back is made up of 28 plus /-2 Kg/m3 with additional top layer of PU foam with density 23 plus /-2 Kg/m3, upholstered with fabric or leatherette. The leg is a welded assembly made up of stainless steel (grade SS 202) tube and plate. Overall Dimensions of Chair shall be Seat Height - 45.0 cm, Height - 82.0cm, Width and Depth of Chair as measured from pedestal - Width-146.0 cm and Depth-92.0 cm.

Providing and Placing in position Office Table. Overall size of the table shall be 1200 W mm x 600 D mm x 750 H mm. The top and modesty panel shall be made of 25 mm thick pre-laminated twin board of E1-P2 grade, edge banded with 2 mm thick PVC lipping. Table top shall be provided with Gromet on work surface for wire management. The understructure shall be made of 25 mm thick Pre-laminated twin board of E1-P2 grade, edge banded with matching 2 mm thick PVC lipping. Hinge Doors shall be made of 25 mm thick pre-laminated twin board of E1-P2 grade, edge banded with 2 mm thick PVC lipping. Handle shall be provided for ease of opening. Storage shall be provided with cam lock for security.

`Providing and Placing in position Staff Chair. The cushioned seat assembly shall be consisting of seat base moulded in glass-filled poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyster fabric. The cushioned back assembly shall be consisting of back inner moulded in Poly-propylene in-situ moulded with polyurethane and upholstered with high stretch knittedpolyster fabric. The back size shall be 45.5 cm x 53 cm H and the seat size shall be 48.5 cm W x 49.0 cm D. The hig hresiliance polyurethane foam used in the seat and back cushion shall be moulded in density 45 plus /- 2 kg/m³ and hardness load shall be 16 plus /- 2 kgf for 25% compression. The seat and back shall be firmly connected to the frame and shall be cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need of complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with back movement during posture changes. The ``S`` shaped spines moulded in high strength glass-filled poly-amide and the spine connector moulded in glass -filled poly-amideform the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 positions tilt limit feature which is inbuilt in seat base and the tension shall be user weight dependent. The armrset assembly shall be made of housing sliding over the armrest struture, both moulded in glass-filled polyamide. The height djustment feature shall be button operated having adjustment stroke of 6.6±0.5 cm. The armrest top shall be made of integral skin PU moulded over plastic inner moulded in glass filled polyamide. The seat height can be adjusted with the pneumatic gas-lift having an adjustment stroke of 9.2 plus /- 0.3 cm. The pedestal shall be injection moulded in glass-filled poly-amide and fitted 5 nos. of twin wheel castors The pedestal shall be 66 plus /- 0.5 cm pitch center dia. and 76 plus /- 1 cm with castors. 5 nos. of twin wheel castors shall be injection moulded in poly-amide having 5.0 plus /- 0.1 cm wheel diameter and assembled with pedestal.

`Providing and Placing in position Conference Table. Overall size of the Table shall be 4200 W mm x 1500 D mm x 740 H mm. Top shall be made of 25 mm thick Pre-laminated twin board, edge banded with matching PVC edge lipping. Access panel shall be provided with soft closing hinges. The understructure shall consist of 25 mm thick * 18 mm thick pre-laminated twin board, edge banded with 2 mm thick matching lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for improving the aesthetics. Bottom cabinet with door shall be provided for flow of wires and cables. Cutout provision below access flap at 4 locations shall be provided.

`Providing and Placing in position High Back Conference Chair. The seat shall be made up of 1.2 plus 0.1cm thk. hot pressed plywood. The Back shall be made up of injection mou1ded glass filled nylon and upholstered using Mesh fabric with high tenacity yarn. SEAT SIZE : 47.0 cm. (W) x 51.5 cm (D) and BACK SIZE : 45.0 cm. (\/V) x 65.3 cm. (H). The HR polyurethane seat foam shall be moulded with density 45 plus /-2 kg/m° and hardness 16 plus 2 kgf for 25% compression. The adjustable armrest shall be designed with the following features : Up-Down adjustment— 8 steps (8 0 plus 0.Scm range), Height adjustable armrest structure which is Powder Coated and fitted with an armrest top. The Lumbar support consists of polypropylene pad with moulded polyurethane foam and covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pa6. Lumbar pad has an adjustment of 8.0 plus 0.5 cm in height. The adjustable tilting mechanism shall be designed with the following features: 360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 4-position locking with anti-shock feature, Seat/back tilting ratio of 1:2. The Neckrest assembly consist of polypropylene pad with moulded polyurethane foam and covered with polyester fabric Neckrest is fixed to Back Assembly through Neckrest connector Neckrest assembly has height adjustment of4.2 plus 0.5 cm and rotation adjustment of overall76” plus 2”. The complete neckrest assembly is retro fit to the main chair. The pneumatic height adjustment shall have an adjustment stroke oi 10.0 plus 0.3 cm. The pedestal is injection moulded in black 30% glass filled nylon and fitted with 5 nos. twin wheel castors. H=The pedestal pitch center dia is 66.1 plus 0.5 cm. The Coat Hanger is made up of injection moulded glass filled nylon. The coat hanger is retro fit and is fixed to the back assembly. The twin wheel castors are injection moulded in black Nylon.

`Poviding and Placing in position Medium Back Conference Chair. The seat shall be made up of 1.2 plus 0.1cm thk. hot pressed plywood. The Back shall be made up of injection mou1ded glass filled nylon and upholstered using Mesh fabric with high tenacity yarn. SEAT SIZE : 47.0 cm. (W) x 51.5 cm (D) and BACK SIZE : 45.0 cm. (\/V) x 65.3 cm. (H). The HR polyurethane seat foam shall be moulded with density 45 plus /-2 kg/m° and hardness 16 plus 2 kgf for 25% compression. The adjustable armrest shall be designed with the following features : Up-Down adjustment— 8 steps (8 0 plus 0.Scm range), Height adjustable armrest structure which is Powder Coated and fitted with an armrest top. The Lumbar support consists of polypropylene pad with moulded polyurethane foam and covered with polyester fabric. The Height of Lumbar pad can be adjusted through two projecting knobs provided on the rear side of the pa6. Lumbar pad has an adjustment of 8.0 plus 0.5 cm in height. The adjustable tilting mechanism shall be designed with the following features: 360° revolving type, Single point control, Front-pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 4-position locking with anti-shock feature, Seat/back tilting ratio of 1:2. The pedestal is injection moulded in black 30% glass filled nylon and fitted with 5 nos. twin wheel castors. H=The pedestal pitch center dia is 66.1 plus 0.5 cm. The twin wheel castors are injection moulded in black Nylon.

Providing and Placing in position Waiting Chair. The seat shell shall be a welded assembly of seat,back and side frame. The seat and back shall be made of 0.12±0.013cm thk CR steel sheet with oblong perforations.They shall be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk HR steel. The welded assembly shall be powder coated ( DFT 40-60 microns). The seat shall has a front water fall edge to provide popliteal clearance for comfortable seating. It also shall has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. Clean and flat surfaces of seat and back shall aids in easy maintenance. The dimensions of seat shall be 47.8 cm (W) x 44.6 cm (D) and of back shall be 41.6 cm (W) x 23. cm (H). Understructure assembly shall consists of connecting beam and leg assembly made of M.S.E.R.W. oblong tube of size 7.5±0.03cm x5.0±0.03cm x 0.02±0.016cm thk.The welded structure assembly shall be powder coated (DFT 40-60 microns ).The leg assembly shall be fitted with shoes and levellers in Nylon. The leg structure shall be designed with minimal area of contact close to ground providing easy access for cleaning purposes. The shoes fiited to leg assembly shall help in aligning the structure for back to back arrangements. Levelers should take care of uneven flooring .Connecting beam shall be fitted with snap locking end cap.It also aids in side-by-side understructure alignment. Armrest assembly shall consists of armrest frame and armrest pad. The armrest frame shall be made up of size 3.175±0.05cm x 0.47±0.027cm thk HR steel and it shall be powder coated (DFT 40-60 microns). Armrest pad shall be injection molded in Nylon and shall be fitted onto the armrest frame. Overall Dimensions shall be Seat Height - 44.1 cm, Height - 78.5 cm, Width and Depth of Chair as measured from pedestal - Width-169.5cm and Depth-63.8 cm.

`Providing and Placing in position 3 Seater Lounge Sofa. The side frame assembly shall be fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It shall be made of 0 3.81 ±0.03cm. x 0.2±0.016cm. thick cmx0.l6cm and black powder coated (DFT 40-60 microns). The ends shall be fitted with ABS moulded end caps. It shall be the connecting beam assy. which holds the two side frames to each other. 2 nos tie members shall be used to connect the side frames. The tie-member shall be of dia 3.81 ±0.03cm x 02±0.016cm. thick cm x 0.16cm and black powder coated (DFT 40-60 microns ). The seat/back assemblies shall be mounted on one of the tie-member which shall has 5.0 ±0.1cm x 5.0 ±0.1 cm x 0.5±0.1cm. thk 5.5 ±0.1cm Long MS. Std. angles welded to mount the seat and back. The seat rest assembly shall be consists of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45 plus /-2 Kg/cm3 with Hardness load=25±2kgf as per lS:7888 for 25% compression of the foam. The complete moulded seat rest assembly shall be covered with a replaceable fabric upholstery cover. The dimensions of seat shall be: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T). The backrest assembly shall be flexing type and consists of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density = 45 plus /- 2 Kg/cm3 with Hardness load 14± 2 kgf as per lS:7888 for 25% compression of the foam. The complete moulded backrest assembly shall be covered with a replaceable fabric upholstery cover. The size of the back shall be 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) The adj. glide shall be injection moulded in black Nylon and fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take care or unleveled floor surface. Overall Dimensions of Chair shall be Seat Height - 43.5 cm, Height - 78.5cm, Width and Depth of Chair as measured from pedestal - Width-164.0cm and Depth-70.0 cm.

`Providing and Placing in position Stretcher. Overall dimension should be 2005 mm (L) x 666 mm (W) x 827 mm (H). It should be removable stretcher on trolley mointed on castors.. The trolley should be made of 31.75 mm and 25.5 mm dia 1.2 mm thick and 1.6 mm thick ERW tube. The casters should be 200 mm dia diagonal lockable castors. te stretcher understructure should be made of 25.4 mm dia 1.6 mm thick ERW tube and the top should be made of 1.2 mm thick CRCA sheet. The stretcher should have provision to mount IV pole at four corners. The product should be pre treated and powder coated with Epoxy polyster powder coating. The maximum load bearing capacity should be 135 kg. ,

Providing and Placing in position Single Bed with understorage. Overall size of the bed shall be 2046 L mm x 919 D mm x 910 H mm with Bedstead height of 440 mm. Bed structure shall be made of metal frame of thickness 25mm square, Pipes in 1.2 mm thickness and MS Channel in 1.0 mm thickness. Partition Panel and plinths shall be made of 25 mm thickness Prelaminated Particle Board. Headboard, tailboard, side board, mattress panel and bottom panel shall be made of 18 mm thickness Prelaminated Particle Board. All exposed edges shall be banded with 0.8 mm thickness PVC edge banding. Overall size of understorage shall be 1491 L mm x 758 D mm x 265 H mm. Body panels shall be made of 18 mm hick prelaminated particle board. Drawer front shall be made of 18 mm thick prelaminated particle board. Drawer bottom shall be made of 9 mm thick prelaminated particle board. All exposed edges shall be banded with 0.8 mm thickness of edge banding. The bed shall be provided with 100 mm thick mattress.

Providing and Placing in position Bedside Table. Overall size of the Table shall be 460 W mm x 461 D mm x 510 H mm. Body panels shall be made of 18 mm hick prelaminated particle board. Drawer front shall be made of 18 mm thick prelaminated particle board. Drawer bottom shall be made of 9 mm thick prelaminated particle board. All exposed edges shall be banded with 0.8 mm thickness of edge banding.

Providing and Placing in position Study Table. Overall size of the Table shall be 900 W mm x 450 D mm x 750 H mm. Top panel shall be made of 18 mm thick Prelaminated Particle Board. All the exposed edges shall be edge banded with 2 mm thick PVC edge banding. Structure shall be made of metal frames made of M.S. 25 mm Square Pipes in 0.9 mm Thickness. Drawer assembly shall be made of drawer front made of 0.6mm CRCA sheet, drawer tray of 0.8mm CRCA sheet.

Providing and Placing in position Study Chair. The seat-back shall be made of blopw molded high-density polyethyleneand shall be fixed on the understructure assembly with the help of stainless steel pop rivets. Seat shall be made of bloe molded high-density polyethylene and shall be fixed on the understructre assembly. All the metal frames and cross-connectors of the understructre shall be made of Mild Steel ERW Tubes, 40 x 20 x 2 mm thick which shall be welded together. The welded structure and cross-connectors shall be coated with 45 microns thickness of epoxy polyster coating. Bag storage tray shall be made of mild steel rod forms a cage at bottom and shall be welded to the main structure. Plastic cap made of polypropylene shall be provided on the foot rest side tubes and back leg tubes adding more aesthetic value to the product. Overall size of the chair shall be 426 mm W x 420 mm D x 771 mm H.

Providing and Placing in position Dining Table. Overall size of the Table shall be 1500 W mm x 900 D mm x 760 H mm. The Table top shall be 19 mm thick and shall be made of MDF with Okume Veneer. It shall be 4 legged Table. Legs of the table shall be made of Solid Wood. The legs shall be L shaped. Finish of the table shall be Veneer.

Providing and placing in position Dining Chair. Overall size of the chair shall be 430 mm W x 565 mm D x 933 mm H. The understrcuture of the chair shall be made of solid wood and shall be PU coated. The seat and back shall be provided with cushion and shall be upholstered with PVC. The chair shall have sleek and contemporary design with high back support.

Providing and Placing in position Round Table. Overall size of the Table shall be 900 Dia x 720 H mm. The worktop shall be made of 18 mm thick MDF. The understructure shall consist of an inner tube assembly with Top Plate, for worktop mounting and an outer tube assembly with round bottom plate. The ineer and outer tube assemblies shall be telescopically connected. The top plate shall be made of 5 mm thick HR steel plates and the bottom plate shall be made of 8 mm thick HR Plate. The inner tube assembly shall be made of 82.5x2 thick round electric resistance welded tubes and 8 mm thick HR steel plates welded together using tungsten insert gas welding. The outer tube assembly shall be shall be made of 89x2.5 thick and round electric resistance welded tubes and 8 mm thick HR steel plates welded together using tungsten insert gas welding. The whole structure shall be epoxy polyster powder coated. (DFT 40-60 microns).

Providing and Placing in position Multipurpose Chair. The seat and back are made up of injection moulded high impact strength polypropylene polymer with indoor gate UV resistance. The dimensions of Back shall be 51.6cm. (W) X 40.5cm. (H) and of seat shall be 52.5cm. (W) X 53.2cm. (D). The Tubular welded frame is made of made of 3.5±0.03cm x 1.5±0.03cm x 0.12±0.0128cm thk M.S. E.R.W. tube and welded connecting tube made of dia 2.22±0.03cm x 0.12±0.0128cm thk stainless steel 202 grade tube. The tubes are buff polished to give shiny finish. The shoes are made of high impact strength polypropylene polymer compound with indoor grade UV resistance and pressed fitted with tubular frame.

Providing and Placing in position Sofa for Recreation Hall. Overall size of the Sofa shall be 1500 W mm x 705 D mm x 790 H mm. Seat understructure shall be made using combination of 12mm plywood vertical panels and pine-wood longitudnal members. 2 mm thick kraft-board shall be stapled on the front side for foam sticking surface. Seat shall be made with 100 mm PU slab stack foam pasted on the seat ply. 12 mm PU slab stack foam shall be pasted along the front and sides. The seat shall be upholstered in fabric. The sofa shall be provided with 2 nos. of 6A electrical sockets with individual switches. The electrical shall be safely housed in the box mounted on pinewood section within the seat and power shall be supplied through a 1.5 m AC cord with ceramic fuse. Back understructure shall be made using combination of 12mm plywood vertical panels and pine-wood longitudnal members. 2 mm thick MDF board shall be stapled on the front side for foam sticking surface. Back shall be made with 50mm PU Slab stack foam, while 12 mm PU slab stack foam shall be pasted along the back and sides. The back shall be upholstered with fabric. The legs shall be made using FSC-certified seasoned teakwood finished with a clear matt coat of PU lacquer. The seat and back are connected using bolts, washers and nuts. Legs shall be assembled using bolts, washers and drive-in T-nuts.

Providing and Placing in position Multipurpose Stool. Overall size of the stool shall be 450 W mm x 450 D mm x 453 H mm. The seat shall be made of synthetic leather upholstered on PU slab stack foam of 65( plus /-0.5cm). It shall be fitted on the upholstered wooden batten box by bolting from the inside. Holding plate shall be made of HR steel of 0.3 cm ( plus /- 0.2 cm) thickness. which shall be bolted to the upholstered seat assembly. Seat size shall be 42 cm W x 42 cm D. Casing of teh stool shall be made of 1 cm ( plus /-0/02cm) MS Rod. Casing shall be powder coated (DFT 40-60 microns). Also, casing shall be coated with nano coat to improve the abrasion resistance of teh surface. Casing size shall be 44 cm W x 44 cm D x 37.5 cm H. Side panel of wooden batten box shall be made of 0.9 cm ( plus /-0.05cm) plywood. The four corners of the batten box shall be made of solid wood which forms the radius. Bottom portion of the batten box shall be covered with 1.2 cm ( plus /- 0.05cm) rubberwood panel ehich shall be finished with clear matt coat of PU lacquer. Sied of wooden batten box shall be upholstered with synthetic leather with backing of slab stack foam of 0.6 cm. Upholstered wooden box can be flipped in the reverse way to use it as a desk surface by keeping it on the casing. Batten box size shall be 40 cm W x 40 cm D x 27.4 cm H.

Providing and Placing in position Single Bed. Overall size of the bed shall be 1980 W mm x 900 D mm x 400 H mm. Bed frame assembly shall be welding of side frame, inner slat. The side frame shall be made of rect. Tube of size 50.8 x 25.4 x 1.2 mm, welded to inner slat of sq. tube of size 19x1 mm MS ERW tube. Cladding shall be made of 12 mm thick ply. Head board and tail board shall be made of sq. pipe 38.1x1.2 mm and sq. pipe of size 25.4x1 mm thick MS ERW tube and support bracket of 3.2 mm thick ms sheet.

Providing and Placing in position Study Table. Overall size of the table shall be 1000 W mm x 480 D mm x 720 H mm. Table top shall be made of 15 mm thick MDF board. Drawer front and inner left and right of the drawer shall be made of 15 mm thick MDF board. Drawer bottom shall be made of 3 mm thick MDF board. Modesty and side panels of the table shall be made of 15 mm thick Particle Board. 0.18 mm thick PVC vaccum lamination shall be done on table top and drawer front, and 0.4 mm thick PVC vaccum lamination shall be done on modesty and side panels.

Providing and Placing in position Café Chair. The seat and back are made up of injection moulded high impact strength polypropylene polymer with indoor gate UV resistance. The dimensions of Back shall be 51.6cm. (W) X 40.5cm. (H) and of seat shall be 52.5cm. (W) X 53.2cm. (D). The Tubular welded frame is made of made of 3.5±0.03cm x 1.5±0.03cm x 0.12±0.0128cm thk M.S. E.R.W. tube and welded connecting tube made of dia 2.22±0.03cm x 0.12±0.0128cm thk stainless steel 202 grade tube. The tubes are buff polished to give shiny finish. The shoes are made of high impact strength polypropylene polymer compound with indoor grade UV resistance and pressed fitted with tubular frame.

Providing and Placing in position Café Table. Overall size of the Table shall be 2329 W mm x 1175 D mm x 750 H mm. Top shall be made of 25 mm thick( plus /-1mm) base material shall be 25 mm MDF board. On top PU painting of minimum 2H hardness with 75% glass as per color chart. Combination color graphics on the centre. Brown Laminate on bottom specially profiled edges for comfort. The Understructure shall be having bend pipe structure of MS powder coated. Pipe dia 38 mm, 2 mm thick and it shall be fitted with top by SS machine screws. Legs shall be of MS powder coated and 38 mm dia. pipe legs are fixed with inderstructure and table top. Glide shall be of Plastic fixed at the understructure to prevent the damage of table top during stacking.

Providing and Placing in position Table. Overall size of the table shall be 1500 W mm x 1500 D mm x 750 H mm. Worktop shall be made of Made of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Side table shall be Made of 25mm Thick Pre-laminated board (PLB) of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Modesty Panel shall be made of 18mm Thick Pre-laminated twin board (PLT) of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Cube legs shall be fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) shall be welded for fixing worktop. These shall be welded together by argo shield welding. This welded structure shall be coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert shall be fixed, on to which a straight M8 leveler fitted which allows for adjustment of the height upto 50mm. Cross Members shall be made from 50mm X 25mm X 1.2mm thick ERW tube (as per IS:7138). These shall be coated with 50 micron epoxy polyester coating. Cross Members shall be assembled by friction fit PDC joinery and grub screws. There shall always two cross members for one table. Soft closing access flap shall be used. Provision for standard size of 8 module electrical shall be offered. Access flap shall be made from Aluminum extrusion, PDC parts made from Aluminum Alloy and plastic parts are made from Nylon 6 and wire brush with nylon bristles. Power box made with 0.8 mm thick CRCA (IS: 513), with switch plate (8 Module cutout provision). This shall be fixed with worktop along the depth at Access Flap position. Hinge Door Unit shall be made of 18mm Thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Door shall be fixed with slide on hinges and handle is provided for ease of opening. Drawer shall be provided with ebco metabox slide and lock for security.

Providing and Placing in position High Back Chair for Warden. The cushioned seat assembly shall be consisting of seat base moulded in glass-filled poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyster fabric. The cushioned back assembly shall be consisting of back inner moulded in Poly-propylene in-situ moulded with polyurethane and upholstered with high stretch knittedpolyster fabric. The back size shall be 45.5 cm x 53 cm H and the seat size shall be 48.5 cm W x 49.0 cm D. The hig hresiliance polyurethane foam used in the seat and back cushion shall be moulded in density 45 plus /- 2 kg/m³ and hardness load shall be 16 plus /- 2 kgf for 25% compression. The seat and back shall be firmly connected to the frame and shall be cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need of complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with back movement during posture changes. The `S` shaped spines moulded in high strength glass-filled poly-amide and the spine connector moulded in glass -filled poly-amideform the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 positions tilt limit feature which is inbuilt in seat base and the tension shall be user weight dependent. The armrset assembly shall be made of housing sliding over the armrest struture, both moulded in glass-filled polyamide. The height djustment feature shall be button operated having adjustment stroke of 6.6±0.5 cm. The armrest top shall be made of integral skin PU moulded over plastic inner moulded in glass filled polyamide. The seat height can be adjusted with the pneumatic gas-lift having an adjustment stroke of 9.2 plus /- 0.3 cm. The pedestal shall be injection moulded in glass-filled poly-amide and fitted 5 nos. of twin wheel castors The pedestal shall be 66 plus /- 0.5 cm pitch center dia. and 76 plus /- 1 cm with castors. 5 nos. of twin wheel castors shall be injection moulded in poly-amide having 5.0 plus /- 0.1 cm wheel diameter and assembled with pedestal.

Providing and Placing in position 3 Seater Sofa. Upperstructure shall be a single shell 1.2 ±0.1cm. thick hot pressed plywood. Dia 4mm zig-zag type assembly is mounted in the understructure for support and additional cushioning purpose. The seat is made up of PU foam with density 32 plus /-2 Kg/m3 having an additional top layer of PU foam with density 28 plus /-2 Kg/m3, upholstered with fabric or leatherette. The back is made up of 28 plus /-2 Kg/m3 with additional top layer of PU foam with density 23 plus /-2 Kg/m3, upholstered with fabric or leatherette. The leg is a welded assembly made up of stainless steel (grade SS 202) tube and plate. Overall Dimensions of Chair shall be Seat Height - 45.0 cm, Height - 82.0cm, Width and Depth of Chair as measured from pedestal - Width-205.5 cm and Depth-92.0 cm.

Providing and Placing in position 1 Seater Sofa. Upperstructure shall be a single shell 1.2 ±0.1cm. thick hot pressed plywood. Dia 4mm zig-zag type assembly is mounted in the understructure for support and additional cushioning purpose. The seat is made up of PU foam with density 32 plus /-2 Kg/m3 having an additional top layer of PU foam with density 28 plus /-2 Kg/m3, upholstered with fabric or leatherette. The back is made up of 28 plus /-2 Kg/m3 with additional top layer of PU foam with density 23 plus /-2 Kg/m3, upholstered with fabric or leatherette. The leg is a welded assembly made up of stainless steel (grade SS 202) tube and plate. Overall Dimensions of Chair shall be Seat Height - 45.0 cm, Height - 82.0cm, Width and Depth of Chair as measured from pedestal - Width-86.0 cm and Depth-92.0 cm.

Providing and Placing in position Round Table. Overall size of the table shall be 1050 Dia. mm x 733 H mm. The Round Table Worktop shall be made up of 25 mm thick PLT. The Round Table shall have Knocked Down Understructure made from 8 mm HR plate with levellers and a vertical support tube of diameter 90 and 2 mm thickness .

Providing and Placing in position 3 Seater Lounge Sofa. The side frame assembly shall be fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It shall be made of 0 3.81 ±0.03cm. x 0.2±0.016cm. thick cmx0.l6cm and black powder coated (DFT 40-60 microns). The ends shall be fitted with ABS moulded end caps. It shall be the connecting beam assy. which holds the two side frames to each other. 2 nos tie members shall be used to connect the side frames. The tie-member shall be of dia 3.81 ±0.03cm x 02±0.016cm. thick cm x 0.16cm and black powder coated (DFT 40-60 microns ). The seat/back assemblies shall be mounted on one of the tie-member which shall has 5.0 ±0.1cm x 5.0 ±0.1 cm x 0.5±0.1cm. thk 5.5 ±0.1cm Long MS. Std. angles welded to mount the seat and back. The seat rest assembly shall be consists of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45 plus /-2 Kg/cm3 with Hardness load=25±2kgf as per lS:7888 for 25% compression of the foam. The complete moulded seat rest assembly shall be covered with a replaceable fabric upholstery cover. The dimensions of seat shall be: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T). The backrest assembly shall be flexing type and consists of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density = 45 plus /- 2 Kg/cm3 with Hardness load 14± 2 kgf as per lS:7888 for 25% compression of the foam. The complete moulded backrest assembly shall be covered with a replaceable fabric upholstery cover. The size of the back shall be 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) The adj. glide shall be injection moulded in black Nylon and fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take care or unleveled floor surface. Overall Dimensions of Chair shall be Seat Height - 43.5 cm, Height - 78.5cm, Width and Depth of Chair as measured from pedestal - Width-164.0cm and Depth-70.0 cm.

Providing and Placing in position Dining Hall Chair. The seat and back are made up of injection moulded high impact strength polypropylene polymer with indoor gate UV resistance. The dimensions of Back shall be 51.6cm. (W) X 40.5cm. (H) and of seat shall be 52.5cm. (W) X 53.2cm. (D). The Tubular welded frame is made of made of 3.5±0.03cm x 1.5±0.03cm x 0.12±0.0128cm thk M.S. E.R.W. tube and welded connecting tube made of dia 2.22±0.03cm x 0.12±0.0128cm thk stainless steel 202 grade tube. The tubes are buff polished to give shiny finish. The shoes are made of high impact strength polypropylene polymer compound with indoor grade UV resistance and pressed fitted with tubular frame. An upholstery cover can be retro fitted on to seat and back. The seat cover is made from High abrasion resistance fabric with foam lamination and 2.5cm PU foam insert. The back cover is made from high abrasion resistance fabric with foam lamination and 0.1 cm PU foam insert.

`Providing and Placing in position High Back Chair for Warden. The cushioned seat assembly shall be consisting of seat base moulded in glass-filled poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyster fabric. The cushioned back assembly shall be consisting of back inner moulded in Poly-propylene in-situ moulded with polyurethane and upholstered with high stretch knittedpolyster fabric. The back size shall be 45.5 cm x 53 cm H and the seat size shall be 48.5 cm W x 49.0 cm D. The hig hresiliance polyurethane foam used in the seat and back cushion shall be moulded in density 45 plus /- 2 kg/m³ and hardness load shall be 16 plus /- 2 kgf for 25% compression. The seat and back shall be firmly connected to the frame and shall be cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need of complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with back movement during posture changes. The ``S`` shaped spines moulded in high strength glass-filled poly-amide and the spine connector moulded in glass -filled poly-amideform the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 positions tilt limit feature which is inbuilt in seat base and the tension shall be user weight dependent. The armrset assembly shall be made of housing sliding over the armrest struture, both moulded in glass-filled polyamide. The height djustment feature shall be button operated having adjustment stroke of 6.6±0.5 cm. The armrest top shall be made of integral skin PU moulded over plastic inner moulded in glass filled polyamide. The seat height can be adjusted with the pneumatic gas-lift having an adjustment stroke of 9.2 plus /- 0.3 cm. The pedestal shall be injection moulded in glass-filled poly-amide and fitted 5 nos. of twin wheel castors The pedestal shall be 66 plus /- 0.5 cm pitch center dia. and 76 plus /- 1 cm with castors. 5 nos. of twin wheel castors shall be injection moulded in poly-amide having 5.0 plus /- 0.1 cm wheel diameter and assembled with pedestal.

Providing and Placing in position 3 Seater Sofa. Upperstructure shall be a single shell 1.2 ±0.1cm. thick hot pressed plywood. Dia 4mm zig-zag type assembly is mounted in the understructure for support and additional cushioning purpose. The seat is made up of PU foam with density 32 plus /-2 Kg/m3 having an additional top layer of PU foam with density 28 plus /-2 Kg/m3, upholstered with fabric or leatherette. The back is made up of 28 plus /-2 Kg/m3 with additional top layer of PU foam with density 23 plus /-2 Kg/m3, upholstered with fabric or leatherette. The leg is a welded assembly made up of stainless steel (grade SS 202) tube and plate. Overall Dimensions of Chair shall be Seat Height - 45.0 cm, Height - 82.0cm, Width and Depth of Chair as measured from pedestal - Width-205.5 cm and Depth-92.0 cm.

Providing and Placing in position 3 Seater Lounge Sofa. The side frame assembly shall be fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It shall be made of 0 3.81 ±0.03cm. x 0.2±0.016cm. thick cmx0.l6cm and black powder coated (DFT 40-60 microns). The ends shall be fitted with ABS moulded end caps. It shall be the connecting beam assy. which holds the two side frames to each other. 2 nos tie members shall be used to connect the side frames. The tie-member shall be of dia 3.81 ±0.03cm x 02±0.016cm. thick cm x 0.16cm and black powder coated (DFT 40-60 microns ). The seat/back assemblies shall be mounted on one of the tie-member which shall has 5.0 ±0.1cm x 5.0 ±0.1 cm x 0.5±0.1cm. thk 5.5 ±0.1cm Long MS. Std. angles welded to mount the seat and back. The seat rest assembly shall be consists of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45 plus /-2 Kg/cm3 with Hardness load=25±2kgf as per lS:7888 for 25% compression of the foam. The complete moulded seat rest assembly shall be covered with a replaceable fabric upholstery cover. The dimensions of seat shall be: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T). The backrest assembly shall be flexing type and consists of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density = 45 plus /- 2 Kg/cm3 with Hardness load 14± 2 kgf as per lS:7888 for 25% compression of the foam. The complete moulded backrest assembly shall be covered with a replaceable fabric upholstery cover. The size of the back shall be 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) The adj. glide shall be injection moulded in black Nylon and fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take care or unleveled floor surface. Overall Dimensions of Chair shall be Seat Height - 43.5 cm, Height - 78.5cm, Width and Depth of Chair as measured from pedestal - Width-164.0cm and Depth-70.0 cm.

Providing and Placing in position Office Table. Overall size of the table shall be 1200 W mm x 600 D mm x 750 H mm. The top and modesty panel shall be made of 25 mm thick pre-laminated twin board of E1-P2 grade, edge banded with 2 mm thick PVC lipping. Table top shall be provided with Gromet on work surface for wire management. The understructure shall be made of 25 mm thick Pre-laminated twin board of E1-P2 grade, edge banded with matching 2 mm thick PVC lipping. Hinge Doors shall be made of 25 mm thick pre-laminated twin board of E1-P2 grade, edge banded with 2 mm thick PVC lipping. Handle shall be provided for ease of opening. Storage shall be provided with cam lock for security.

`Providing and Placing in position Chair for Lecture Hall. The seat sub-assembly shall be made up of 1.2±0.1cm Thk Plywood, upholstered with polyester fabric over moulded foam and covered with an injection-moulded polypropylene outer cover. The seat can be manually tipped-up when not in use. The back sub-assembly shall be made up of injection-moulded glass filled polypropylene inner upholstered with polyester fabric over moulded foam and covered with an injection-moulded polypropylene outer cover. Both these sub-assemblies shall be fixed to the tubular structure. Back size : 46.3 W cm x 59 H cm. Seat size : 47 W cm x 49.5 D cm. The support structure shall be made of a U-bent Ø3.81±0.03cm x 0.2 ±0.016cm Thk M.S.E.R.W round tube and shall be supported using two Ø3.81±0.03cm x 0.2 ±0.016cm Thk M.S.E.R.W round tube at the bottom. The tip-up seat assembly shall be pivoted on a welded support assembly of a straight and bent tube of Ø2.22±0.03cm x 0.25 ±0.016cm Thk M.S.E.R.W round tube which shall be welded to the main U-Bent Leg. The Back assembly is mounted on a 3.15mm thick Armrest bracket using Screw. The frame structure shall be grouted using 3 Bolts on a 5mm thick base plate which shall be welded to the upper frame structure. The bolts with base plate shall be enclosed using PP foundation bolt cover. The HR polyurethane foam shall be moulded with density = 45 ±2 kg/m³ and Hardness load for Seat 16 ± 2 kgf and Hardness load for back 14 ± 2 kgf for 25% compression. The armrest shall be made of Injection moulded PP compound. The Armrest shall be mounted on a 3.15mm thick HR sheet which shall be welded on the tubular frame. The desklet assembly shall be flip-up type and shall be supported by a welded assembly of extension tube and a bent support tube of 1.9 ±0.02cm dia x 0.2 ±0.016cm Thk M.S.E.R.W. tube. The PLT desklet top shall be PP edge moulded. Rubber Bangers shall be installed to prevent banging and scratch in the bottom part of desklet. The desklet can be adjusted by 50 mm in depth as per comfort and reach requirement. Steel components shall be epoxy polyester powder coated (DFT 40-60 microns).

Providing and Placing in posirion Desk Cum Bench for Lecture Halls. The top shall be made of 25mm thk PLB, legs shall be made of 2mm thk oval tube with 5mm thk HR bracket, Seat understructure shall be made of 5mm thk HR plus 8mm thk ply and Modesty shall be made of 25mm thk pre laminted twin board. Seat support frame and side clads shall be made of 18mm thk plate. Legs shall be made of MS ERW tube section (IS7138) of size 75x25x2 mm thick oval tube with 5mm thk HR brackets and 2mm thick CRCA brackets welded on to the tubes. Assembly shall be powder coated with epoxy polyester. Legs height varies from 705mm to 1005mm in pitch of 50 as per layout. Sturdy anchoring by bolts on to base of 8mm thk plate for proper resting of leg. The shoes shall be made of bolts on to base of 8mm thk plate for resting of leg. The two side clads shall be made of 18mm thk plate with 0.8mm thk PVC lipping and on the outside covered with welded metal structure made of 2mm thk CRCA powder coated with epoxy polyster. The worktops shall be made of 25mm thk PLB. All edges of work surface shall be provided with machine pressed 2mm thick pvc edge band glued with hot melt glue. The seat shall have self closing mechanism which will operate by means of dead weight. Seat understructure shall be made from combination of welded fabricated structure of 5mm thk HR and 8mm thk ply with moulded PU foam of density 55kg/cu. mt on top which in turn shall be covered with stiched uplholstery made of leatherite. Seat assy shall be covered on both sides by means of seat cover made of pp. The seat back shall be made from combination of 8mm thk ply with moulded foam on top which in turn shall be covered with stitched upholstery made leatherite. The seat support frame shall be made from combination of MS ERW tube section of size 80x40x2.5 mm thk rectangular tube and MS ERW tube section of size 48x19.1x2 mm thk oval tube welded together. Assembly shall be powder coated with Epoxy polyester. Cap made of ultramid are provided from front to cover the oval tubes. The modesty shall be made of 25mm thk pre laminated twin board. All the edges of modesty shall be provided with machine pressed 2mm thk pvc edge band glue with hot melt glue.

Providing and Placing in position Main Table. Overall size of the table shall be 2350 mm (L) x 1150 mm (D) x 750 mm (H), Side Table 1200 mm (L) x 500 mm (D) x 750 mm (H) and integrated Pedestals 2Nos fixed type Drawer Units in each table set of size 470 mm (W) x 500 mm (D) x 725 mm (H) - one in Main table and one in Side Table. The Main Table and Side Table tops shall be made of 25mm thick MDF with bottom side pre-laminate confirming to IS-14587:1998 and 0.4mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The modesty panel shall be made of 25mm thick MDF - one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure shall be made of 25mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching 2mm thick PVC lipping. The drawer unit shall be made of 25mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching 2mm thick PVC lipping. Drawer Units - Drawer fronts shall be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Each drawer unit shall contain 3 drawers i.e. Box plus Box plus File type which uses powder coated 400mm long metal Panel Drawer Slides. Drawer extension shall be 325mm. Drawers shall have a soft closing and anti slam mechanism. Chrome plated flat type handles shall be provided for ease of opening. Drawer units are provided with lock for security.

Providing and Placing in position Display Unit. Overall size of the Display Unit shall be 1800mm(L) x 500mm(D) x 1800mm(H). The Back unit shall comprises bottom sliding storage unit and top hollow storage spcae which are covered with top panels. The top panel of the back unit shall be made up of 25mm thick MDF one side pre-laminated board confirming to IS:14587:1998 with 0.4 mm PVC membrane pressed on top. Sliding door unit shall be made of made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing and anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security.

Providing and Placing in position High Back Chair. The cushioned seats shall be made of injection moulded plastic outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm W x 77 cm D. The armrest top shall be moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable type tubular armrest support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism shall be designed with the following features : 360° revolving type, front-pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort, Tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the mechanism housing is made up of aluminium black powder coated. Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm. Back frame shall be connected to the up/down mechanism housed in plastic T spine. It can be adjusted in the range of 7.4 ± 0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.

Providing and Placing in position Vistors Chair. The cushioned seats shall be made of injection moulded plastic outer and inner. Plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foamof Density = 45±2 kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm W x 77 cm D. The tubular frame shall be cantilever type and made of Ø2.54±0.03 cm x 0.2±0.016 cm thick SS 202 tube. The back shall be connected to the frame through chrome plated high pressure die cast connector piece.

Providing and Placing in position 3 seater Sofa. Upperstructure shall be a single shell 1.2 ±0.1cm. thick hot pressed plywood. Dia 4mm zig-zag type assembly is mounted in the understructure for support and additional cushioning purpose. The seat is made up of PU foam with density 32 plus /-2 Kg/m3 having an additional top layer of PU foam with density 28 plus /-2 Kg/m3, upholstered with fabric or leatherette. The back is made up of 28 plus /-2 Kg/m3 with additional top layer of PU foam with density 23 plus /-2 Kg/m3, upholstered with fabric or leatherette. The leg is a welded assembly made up of stainless steel (grade SS 202) tube and plate. Overall Dimensions of Chair shall be Seat Height - 45.0 cm, Height - 82.0cm, Width and Depth of Chair as measured from pedestal - Width-205.5 cm and Depth-92.0 cm.

Providing and Placing in position 2 seater sofa. Upperstructure shall be a single shell 1.2 ±0.1cm. thick hot pressed plywood. Dia 4mm zig-zag type assembly is mounted in the understructure for support and additional cushioning purpose. The seat is made up of PU foam with density 32 plus /-2 Kg/m3 having an additional top layer of PU foam with density 28 plus /-2 Kg/m3, upholstered with fabric or leatherette. The back is made up of 28 plus /-2 Kg/m3 with additional top layer of PU foam with density 23 plus /-2 Kg/m3, upholstered with fabric or leatherette. The leg is a welded assembly made up of stainless steel (grade SS 202) tube and plate. Overall Dimensions of Chair shall be Seat Height - 45.0 cm, Height - 82.0cm, Width and Depth of Chair as measured from pedestal - Width-146.0 cm and Depth-92.0 cm.

Providing and Placing in position Center Table. The top shall be made of which shall be 12 plus /-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12 plus /-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 cm.

Providing and Placing in position Corner Table. The top shall be made of glass which shall be 12 plus /-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12 plus /-0.04 as per IS:1762. overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm.

Providing and Placing in position 1 Seater Sofa. Upperstructure shall be a single shell 1.2 ±0.1cm. thick hot pressed plywood. Dia 4mm zig-zag type assembly is mounted in the understructure for support and additional cushioning purpose. The seat is made up of PU foam with density 32 plus /-2 Kg/m3 having an additional top layer of PU foam with density 28 plus /-2 Kg/m3, upholstered with fabric or leatherette. The back is made up of 28 plus /-2 Kg/m3 with additional top layer of PU foam with density 23 plus /-2 Kg/m3, upholstered with fabric or leatherette. The leg is a welded assembly made up of stainless steel (grade SS 202) tube and plate. Overall Dimensions of Chair shall be Seat Height - 45.0 cm, Height - 82.0cm, Width and Depth of Chair as measured from pedestal - Width-86.0 cm and Depth-92.0 cm.

Providing and Placing in position Main Table. Overall size of the table shall be 2100 mm (L) x 1050 mm (D) x 750 mm (H), Side Table 1200 mm (L) x 500 mm (D) x 750 mm (H) and integrated Pedestals 2Nos fixed type Drawer Units in each table set of size 470 mm (W) x 500 mm (D) x 725 mm (H) - one in Main table and one in Side Table. The Main Table and Side Table tops shall be made of 25mm thick MDF with bottom side pre-laminate confirming to IS-14587:1998 and 0.4mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The modesty panel shall be made of 25mm thick MDF - one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure shall be made of 25mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching 2mm thick PVC lipping. The drawer unit shall be made of 25mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching 2mm thick PVC lipping. Drawer Units - Drawer fronts shall be made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Each drawer unit shall contain 3 drawers i.e. Box plus Box plus File type which uses powder coated 400mm long metal Panel Drawer Slides. Drawer extension shall be 325mm. Drawers shall have a soft closing and anti slam mechanism. Chrome plated flat type handles shall be provided for ease of opening. Drawer units are provided with lock for security.

Providing and Placing in position Display Unit. Overall size of the Display Unit shall be 1800mm(L) x 500mm(D) x 1100mm(H). The Back unit shall comprises bottom sliding storage unit and top hollow storage spcae which are covered with top panels. The top panel of the back unit shall be made up of 25mm thick MDF one side pre-laminated board confirming to IS:14587:1998 with 0.4 mm PVC membrane pressed on top. Sliding door unit shall be made of made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping for body panels like side, bottom,back and shelves. Shutters are made of 25mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. Shutters have a soft closing and anti slam mechanism. Handles are provided for ease of opening. Storage is provided with lock for security.

Providing and Placing in position High Back Chair. Overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat Height. The seat is cushioned seat made of injection molded plastic outer and inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, and hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm. Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The pedestal is high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal.

Providing and Placing in position Visitors Chair. Overall size of 60.9 W m x 64.2 D cm x 98.2 H cm x 44.8 Seat Height cm. The seat is cushioned seat made of injection molded plastic outer and inner. Plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, and hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The tubular frame is cantilever type and made of Ø2.54±0.03cm x 0.2±0.016 cm thick SS 202 tube. The back connected to frame through chrome plated high pressure die casted connector pipe.

Providing and Placing in position Main Chair. The seat shall be made up of 1.2 plus /-0.1 cm thk hot pressed plywood. The Back shall be made up of injection moulded glass filled nylon and upholstered using Micro mesh fabric with high tenacity yarn with 28 density foam Sandwich in lumbar area. SEAT SIZE shall be 47.0 cm. (W) x 51.5 cm (D) and BACK SIZE shall be 45.0 cm. ”(W) x 65.3 cm. (H). The HR polyurethane seat foam shall moulded with density 45 plus /-2 kg/m` and hardness 16 plus 2 kgf as per IS:7888 for 25% compression. The adjustable armrest shall be designed with the folIowing features: • Up-Down adjustment— 8 steps (8.0 plus 0.Scm range), • Height adjustable armrest structure which is Powder Coated and fitted with an armrest top, • Fixed Armrest Top is PU moulded over metal insert. The adjustable tilting mechanism shall be designed with the following features: • 360° revolving type, • Single point control, • Front-pivot for tilt with feet resting on ground ensuring more comfort, • Tilt tension adjustment, • 4-position locking with anti shock feature, • Seat/back tilting ratio of 1:2. The Neckrest assembly consist of polypropylène pad with moulded polyurethane foam and covered with polyester fabric. Neckrest shall be fixed to Back Assembly through Neckrest connector. Neckrest assembly shall have height adjustment of 4.2 plus 0 5 cm and rotation adjustment of overall 76 plus /- 2 degree. The complète neckrest assembly shall be retro fit to the main chair. The pneumatic height adjustment shall have an adjustment Stroke of 10.0 plus /-0.3 cm. The pedestal shall be injection moulded in black 33% glass-filled Nylons and fitted with 5 nos. twin wheel castors. The pedestal pitch-center dia is 66.1 plus /-0.5 cm. (76.1 plus /-1.0 cm. with castors). The Coat Hanger shall be made up of injection moulded glass filled nylon. The Coat hanger shall be retro fit and is fixed to the back assembly.

Providing and Placing in position 3 Seater Sofa for Waiting Room. The side frame assembly shall be fitted to the two ends of the connecting beam assembly to form the leg-cum-armrest assembly. It shall be made of 0 3.81 ±0.03cm. x 0.2±0.016cm. thick cmx0.l6cm and black powder coated (DFT 40-60 microns). The ends shall be fitted with ABS moulded end caps. It shall be the connecting beam assy. which holds the two side frames to each other. 2 nos tie members shall be used to connect the side frames. The tie-member shall be of dia 3.81 ±0.03cm x 02±0.016cm. thick cm x 0.16cm and black powder coated (DFT 40-60 microns ). The seat/back assemblies shall be mounted on one of the tie-member which shall has 5.0 ±0.1cm x 5.0 ±0.1 cm x 0.5±0.1cm. thk 5.5 ±0.1cm Long MS. Std. angles welded to mount the seat and back. The seat rest assembly shall be consists of a fabricated inner-frame assembly insitu-moulded High Resilience (HR) Polyurethane foam having density = 45 plus /-2 Kg/cm3 with Hardness load=25±2kgf as per lS:7888 for 25% compression of the foam. The complete moulded seat rest assembly shall be covered with a replaceable fabric upholstery cover. The dimensions of seat shall be: 52.0cm. (W) X 50.0cm. (D) X 6.0cm. (T). The backrest assembly shall be flexing type and consists of a fabricated inner-frame assembly insitu-moulded with High Resilience (HR) Polyurethane foam having density = 45 plus /- 2 Kg/cm3 with Hardness load 14± 2 kgf as per lS:7888 for 25% compression of the foam. The complete moulded backrest assembly shall be covered with a replaceable fabric upholstery cover. The size of the back shall be 52.0cm. (W) X 59.0cm. (H) X 6.0cm. (T) The adj. glide shall be injection moulded in black Nylon and fitted to the front end of side frame assembly along with ABS moulded adj. Glide base to take care or unleveled floor surface. Overall Dimensions of Chair shall be Seat Height - 43.5 cm, Height - 78.5cm, Width and Depth of Chair as measured from pedestal - Width-164.0cm and Depth-70.0 cm.

Providing and Placing in position Conference Table. Overal size of the Table shall be 6250 L mm x 2350 D mm x 740 H mm. The table top shall be made of 25 mm thick pre-laminated twin board, edge banded with matching 2 mm thick PWD edge banding. Plastic ABS access flap shall be provided for easy access to wires and cables. The Understructure shall be made of mixture of 18mm thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Aluminium alloy 63400 - WP profile shall be used for connecting panels together. Modesty Panel shall be made of 18mm Thick Pre-laminated twin board of E1-P2 grade, Edge banded with matching 2 mm thick PVC lipping. Powder coated accent metal strip shall be provided below work surface to enhance aesthetics. It shall be made of 0.8mm CRCA as per IS 513, and shall be epoxy polyester powder coated (DFT 40-60 microns). Wire Management shall be an array of panels made of 0.8mm CRCA MS IS:513, and shall be epoxy polyester powder coated (DFT 40-60 microns) shall be used for flow of wires and cables. Provision to mount 6 module switch plate shall be provided below worktop. Cutout on top with two piece injection moulded plastic part polymer component shall be fitted to pullout audio,video cables onto worktop and connect devices charger to power socket below worktop.

Providing and Placing in position Compactors for Record Room. Size: Overall Dimensions of 1200 mm (W) x 400 mm (D) x 2000 mm (H). The Construction shall be rigid knock down made out of 0.8 thick CRCA steel. Each configuration have following type of blocks – Single Static (SS), Single Last (SL),Twin Mobile(TM). Finish: Finish shall be Epoxy polyester powder coated thickness of 40 microns. Construction: Shelf construction shall be made from CRCA steel 0.8 mm. Uniformly distributed load capacity of 100 Kg. Undercarriage: Undercarriage shall have construction in welded frame made of HR sheet 3 mm thick. Movement : The Movements shall be Drive Type configuration. Locking: Fittings shall be centralized locking arrangement through locking stiffener mounted onto back of single last unit so that it gets locked on channels when all the units are brought together. The Recess handle lock is placed at suitable height .The ‘sprocket-chain’ arrangement is covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the body. Fixed unit (SD) does not have the Handle. Each units shall have Locking Knob for manual locking of individual units when a person is using those units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent derailment.The nuts and bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 15 for SD3. Label holder: It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted. Rail Pair: It consists of ‘C’ section 2 mm thk HR sheet and Square 25.4mm X 2mm thk ERW tube – both connected by screws. Prior to the grouting of the guide channels with the help of raul plug and screw, ensure the ground is level. The rail channels are of 3 lengths i.e., 800mm, 1600mm and 2400mm.

Providing and Placing in position Main Chair. The cushioned seat assembly shall be consisting of seat base moulded in glass-filled poly-amide, moulded polyurethane foam and upholstered with high stretch knitted polyster fabric. The cushioned back assembly shall be consisting of back inner moulded in Poly-propylene in-situ moulded with polyurethane and upholstered with high stretch knitted polyster fabric. The back size shall be 45.5 cm x 53 cm H and the seat size shall be 48.5 cm W x 49.0 cm D. The hig hresiliance polyurethane foam used in the seat and back cushion shall be moulded in density 45 plus /- 2 kg/m³ and hardness load shall be 16 plus /- 2 kgf for 25% compression. The seat and back shall be firmly connected to the frame and shall be cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need of complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with back movement during posture changes. The `S` shaped spines moulded in high strength glass-filled poly-amide and the spine connector moulded in glass -filled poly-amideform the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 positions tilt limit feature which is inbuilt in seat base and the tension shall be user weight dependent. The armrset assembly shall be made of housing sliding over the armrest struture, both moulded in glass-filled polyamide. The height djustment feature shall be button operated having adjustment stroke of 6.6±0.5 cm. The armrest top shall be made of integral skin PU moulded over plastic inner moulded in glass filled polyamide. The seat height can be adjusted with the pneumatic gas-lift having an adjustment stroke of 9.2 plus /- 0.3 cm. The pedestal shall be injection moulded in glass-filled poly-amide and fitted 5 nos. of twin wheel castors The pedestal shall be 66 plus /- 0.5 cm pitch center dia. and 76 plus /- 1 cm with castors. 5 nos. of twin wheel castors shall be injection moulded in poly-amide having 5.0 plus /- 0.1 cm wheel diameter and assembled with pedestal.

`Providing and Placing in position Office Table. Overall size of the table shall be 1500 W mm x 750 D mm x 740 H mm. Worktop shall be made of 25mm Thick Pre-laminated board, Edge banded with matching 2 mm thick PVC lipping. Access Flap provided on work surface for wire management. Modesty shall be made of 18mm Thick Pre-laminated twin board, Edge banded with matching 2 mm thick PVC lipping. Legs shall be fabricated from MS ERW Tube of 50 mm x 25 mm x 1.2mm thick and 40 mm x 40 mm x 1.2 mm thick (as per IS: 7138). At the top surface of leg, support brackets of 3 mm thick HR (as per IS: 2062) shall be welded for fixing worktop. These shall be welded together by argo shield welding. This welded structure is coated with 50 micron epoxy polyester coating. At the base, a plastic cap with M8 molded insert is fixed, on to which a straight M8 leveler fitted which allows for adjustment of the height upto 50mm. Cross Members shall be made from 50mm X 25mm X 1.2mm thick ERW tube (as per IS:7138). These shall be coated with 50 micron epoxy polyester coating. Cross Members shall be assembled by friction fit PDC joinery and grub screws. There are always two cross members for one table. Soft closing access flap shall be used in Table. Provision for standard size of 8 module electrical shall be offered. Access flap shall be made from Aluminum extrusion, PDC parts made from Aluminum. Alloy and plastic parts shall be made from Nylon 6 and wire brush with nylon bristles. Power box shall be made with 0.8 mm thick CRCA (IS: 513), with switch plate (8 Module cutout provision). This shall be fixed with worktop along the depth at Access Flap position.

Providig and Placing in poition Waiting Chair for Counsellor Room. The seat shell shall be a welded assembly of seat,back and side frame. The seat and back shall be made of 0.12±0.013cm thk CR steel sheet with oblong perforations.They shall be welded to sideframe of size 3.2±0.05cm x 0.5 ± 0.05 cm thk HR steel. The welded assembly shall be powder coated ( DFT 40-60 microns). The seat shall has a front water fall edge to provide popliteal clearance for comfortable seating. It also shall has a buttock support curve that not only provides rear support but also prevents small children from falling through the gap between seat and back. Clean and flat surfaces of seat and back shall aids in easy maintenance. The dimensions of seat shall be 47.8 cm (W) x 44.6 cm (D) and of back shall be 41.6 cm (W) x 23. cm (H). Understructure assembly shall consists of connecting beam and leg assembly made of M.S.E.R.W. oblong tube of size 7.5±0.03cm x5.0±0.03cm x 0.02±0.016cm thk.The welded structure assembly shall be powder coated (DFT 40-60 microns ).The leg assembly shall be fitted with shoes and levellers in Nylon. The leg structure shall be designed with minimal area of contact close to ground providing easy access for cleaning purposes. The shoes fiited to leg assembly shall help in aligning the structure for back to back arrangements. Levelers should take care of uneven flooring .Connecting beam shall be fitted with snap locking end cap.It also aids in side-by-side understructure alignment. Armrest assembly shall consists of armrest frame and armrest pad. The armrest frame shall be made up of size 3.175±0.05cm x 0.47±0.027cm thk HR steel and it shall be powder coated (DFT 40-60 microns). Armrest pad shall be injection molded in Nylon and shall be fitted onto the armrest frame. Overall Dimensions shall be Seat Height - 44.1 cm, Height - 78.5 cm, Width and Depth of Chair as measured from pedestal - Width-169.5cm and Depth-63.8 cm.

Providing and Placing in position Café Table. Overall size of the Table shall be 1135 W mm x 1175 D mm x 750 H mm. Top shall be 25 mm thick( plus /-1mm) base material shall be 25 mm MDF board . On top PU painting of minimum 2H hardness with 75% glass as per color chart .Combination color graphics on the centre . Brown Laminate on bottom specially profiled edges for comfort . The Understructure shall be having bend pipe structure of MS powder coated . Pipe dia 38 mm , 2 mm thick and it shall be fitted with top by SS machine screws . Legs shall be of MS powder coated and 38 mm dia. pipe legs are fixed with inderstructure and table top . Glide shall be of Plastic fixed at the understructure to prevent the damage of table top during stacking .

Providing and Placing in position Café Chair. The single piece seat back shell shall be made up of injection moulded high impact strength glass filled polypropylene polymer compound. SHELL SIZE shall be 44.0 cm. (W) x 50.2 cm. (D) x 40.5 cm. (H). The powder coated (DFT 50±10 microns) welded tubular frame shall be made from Ø 2.22 ± 0.03 cm x 0.16 ± 0.0128 cm M.S. E.R.W tube. The 0.16 ± 0.008 cm thk CRCA sheet shall be welded to tubes for fixing shell to the frame. The shoe shall be made of high impact strength polypropylene polymer compound and are fitted at the end of the tubular frame.

Providing and Placing in position Main Table for SHO Office. Overall size of the Table shall be 1800 W x 900 D x 750 H and ERU 1200 W x 600 D x 750 H. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, edge banded with matching 2 mm thick PVC lipping. There shall be 2 Nos. of Drawer Units i.e., 1 Nos. under Main Table and 1 Nos. under ERU, where Drawer fronts shall be made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing and anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Providing and Placing in position Chair with Desklet for Teaching Room. The seat and back are made up of injection moulded high impact strength polypropylene polymer with indoor gate UV resistance. The dimensions of Back shall be 51.6cm. (W) X 40.5cm. (H) and of seat shall be 52.5cm. (W) X 53.2cm. (D). The powder-coated (DFT 40-60 microns ) frame structure shall be made of 3.5±0.03cm x 1.5±0.03cm x 0.16±0.0128cm thk M.S. E.R.W. tube and welded connecting tube made of dia 2.22±0.03cm x 0.16±0.0128cm thk M.S. E.R.W. SQUARE tube to form the Mainframe assembly. The shoes are made of high impact strength polypropylene polymer compound with indoor grade UV resistance and pressed fitted with tubular frame. The paper tray is made of dia 0.4 plus /- 0.005cm M.S. rod which is spot welded to form a mesh typestructure. It is powder coated(DFT 50 plus /-10 microns). The size of the tray is 40.1 (W) x 36.1 (D) x 22.0 (H) cm. The `L` shape desklet is madeup of 1.8 plus /-0.05cm thk pre laminated particle board with 0.2 plus /-0.05cm thk injectio moulded polypropylene all around. Desklet has front and back adjustment of 4.4cm plus /-0.5 cm. The outer dimensions of desklet are 31.5 plus /-0.1cm (W) x 47.0 plus /-0.1 cm (D). An upholstery cover can be retro fitted on to seat and back.

Providing and fixing Laboratory Tables Understructure of required colour scheme consists of D-Frames Assembly, Horizontal members with Granite Top and Cover Panels. These understructures shall be of 750mm or 900mm height as per site requirement or as per the direction of Engineer-in-Charge. The Top surface area of under structure shall be measured for payment. The understructure shall comprises of following components :- . The Product must comply with SEFA -10 Standards and OEM must be the Member of SEFA for last 9 years. D-Frame Assembly `All D-Frames assemblies shall be manufactured from standard hollow metal sections: confirming to latest I.S. Code 7138 (Indian Standard specification for steel tubes for furniture) and all sheet metal components shall be of CRCA confirming to latest IS Code 513. The dimensions of D Frame shall depend upon the depth of the understructure. The overall depth (F) of DFrame shall be 705mm for 750mm Depth Structure and 555mm for 600mm depth (as per Drawing) and Depth of Extended Frame (G) shall be 255 mm for 750mm Depth and 110mm for 600mm depth (as per drawing). All frame-work shall be pre-treated with superior powder coated finish with 40-60 micron thickness. The structure of D-frame with horizontal units shall withstand 10 degree tilt (backwards) without toppling. The D-Frames shall have a provision to fix suspended storage cabinets. Side frame shall be of welded MS ERW tube of dimension 30 x 30 x 1.6mm thickness. Bracket for pipe : MS CRCA 2mm thick. Wall bracket : MS CRCA 2mm thick. Levelling screws: 2 nos. of M-10 levellers (MS plus Nylon) Adjustments possible with range 20mm. ` HORIZONTAL MEMBERS Horizontal members shall join two D-Frames to form the structure. Horizontal members shall be made from rectangular pipes of 1.6mm thickness. Cross-sectional dimensions of the pipe shall be 30 x 30mm with a minimum of 1.6 mm thickness. They shall be made of CRCA MS sheet powder coated of 40-60 micron thickness. Horizontal members connect two D-Frames together by using C-clamps/U-clamps together with the D-Frames and Horizontal Members . The skeletal structure of the work-bench is formed on which the worktop shall be placed and the hanging-type storage cabinets shall be suspended. Horizontal Members determine the width of the lab workbench as they form the member (distance) between two adjacent DFrames. They shall be available in various widths of 450mm, 600mm, 900mm, 1050mm, 1200mm, 1350mm, 1500mm, 1650mm and 1800mm (Tolerance plus /- 10mm). These horizontal units together constitute a table set. COVER PANELS All side cover panels and back panels, filler panels shall be made from CRCA MS panels of minimum 0.8mm thickness with epoxy powder coating with thickness of 40-60 microns, bracket of min.1.2mm thickness WORKTOP The complete structure shall be provided with a Worktop of 20mm ( plus /- 2mm) thick Jet Black Granite. The exposed edges of the worktop shall be chamfered and polished . The bottom of cantilever portion of the worktop shall be polished and V-groove shall be provided throughout the length of the exposed edges to protect the cabinets from coming in contact with the spillages. The overhang on the storage cabinet is 25 mm at the front side and 30mm at the sides. The backing material shall be neoprene mat of 6 mm thickness. All the above items shall be as per photo, sketch specifications and direction of engineer-in-charge.

`Providing and fixing Work bench Storage cabinets of required colour scheme as per following:- The storage cabinet shall be Welded body with load bearing members such as top, bottom and stiffeners made of 0.8mm thick CRCA Sheet. A drawer separator shall be provided made of 1.2mm thick CRCA sheet. The storage unit shall be provided with a shelf made of 0.8mm thick CRCA sheet which is adjustable to 6 slots of 4060mm. Each shelf shall have load carrying capacity of 40 kgs. Shutter provided is overclosing with 270 degree opening. It has a sandwich construction with profile as a sound dampener. The drawer shall be provided as per the manufacturers specifications and direction of Engineer -in-Charge. The complete storage unit shall be powder coated with thickness of 40-60 microns and is suspended from tubular understructure, with an overlay shutter. The cabinet has a corrosion resistance magnetic strip as shutter catch, shutter and drawer are equipped with 180 degree cam lock. Semi recessed handle and five knuckle overlay hinge(SS-304) with 270 degree opening. Drawer and Shutter shall be provided with a lock 180 Degree cam with 4mm thick lever. Cabinet fixing brackets shall be of 2mm thickness. Note:- The cost of storage cabinet does not includes the cost of basic understructure, the cost of understructure shall be paid in Item No 1. (All the above items shall be as per photo, sketch specifications and direction of engineer-incharge.) ` Storage unit of Size 600mm(W) x 450mm(D) x 675mm(H) with 1 Drawer and 2 Shutters

`Providing and fixing Work bench Storage cabinets of required colour scheme as per following:- The storage cabinet shall be Welded body with load bearing members such as top, bottom and stiffeners made of 0.8mm thick CRCA Sheet. A drawer separator shall be provided made of 1.2mm thick CRCA sheet. The storage unit shall be provided with a shelf made of 0.8mm thick CRCA sheet which is adjustable to 6 slots of 4060mm. Each shelf shall have load carrying capacity of 40 kgs. Shutter provided is overclosing with 270 degree opening. It has a sandwich construction with profile as a sound dampener. The drawer shall be provided as per the manufacturers specifications and direction of Engineer -in-Charge. The complete storage unit shall be powder coated with thickness of 40-60 microns and is suspended from tubular understructure, with an overlay shutter. The cabinet has a corrosion resistance magnetic strip as shutter catch, shutter and drawer are equipped with 180 degree cam lock. Semi recessed handle and five knuckle overlay hinge(SS-304) with 270 degree opening. Drawer and Shutter shall be provided with a lock 180 Degree cam with 4mm thick lever. Cabinet fixing brackets shall be of 2mm thickness. Note:- The cost of storage cabinet does not includes the cost of basic understructure, the cost of understructure shall be paid in Item No 1. (All the above items shall be as per photo, sketch specifications and direction of engineer-incharge.) `Storage unit of Size 450mm(W) x 450mm(D) x 675mm(H) with 1 Drawer and 1 Shutter

`Providing and fixing Sink Units of size 600mm(W) which shall comprises of Sink Cabinet, Polypropylene Sink Unit and 1-Way Goose Neck 360 Degree revolving Faucet.as per following SINK CABINET `Sink cabinet. :- The Sink cabinet shall be Welded body with load bearing members such as top, bottom and stiffeners made of 0.8mm thick CRCA Sheet. The cabinet unit shall be provided with Pair of Shutters. Shutter has a sandwich construction with profile as a sound dampener. The complete unit shall be epoxy powder coated with thickness of 40-60 microns and is suspended from tubular understructure, with an overlay shutter. The cabinet has a corrosion resistance magnetic strip as shutter catch. Shutter shall be provided with semi recessed handle and five knuckle overlay hinge (SS-304) with 270 degree opening. Cabinet fixing brackets of 2mm thickness. The cost of sink cabinet does not includes the cost of basic understructure as the cost of understructure shall be paid in Item No 1. All the above items shall be as per photo, sketch specifications and direction of engineer-incharge. ` POLYPROPYLENE SINK ASSEMBLY `Providing and fixing Polypropylene Sink with PP Waste, Anti-Siphon Bottle Trap and Flexible Drainage Pipe. Sink bowl shall be Polypropylene Molded made up of 5mm thick high density and elastic poly propylene with good resistance to organic solvents. Standard bowl size shall 500mm(L) x 400mm(W) x 300mm(D). ` 1 WAY WATER FAUCET `Providing and fixing 1-Way 360 Degree Revolving Water Faucet. Faucet fittings shall be laboratory grade. Water faucet and valve bodies shall be cast red brass alloy or bronze forgings, all fittings shall be powder plated. Brass as per IS:319, Pipe as per : IS:407,O utlet nipple in PP construction. PP knob to be used. All gasket and O-ring of Nitrile Rubber make. Inlet connection 1/2`` BSP. Gooseneck spout with 360 degree rotation with 100000 life cycles. Pneumatic test at 250 psi, hydraulic test at 125 psi, bursting test at 500 psi. Coating to be glossy epoxy fusion bond. The Faucet shall be fixed to the existing water outlet by providing PVC connection with brass unions of required length. All the above items shall be as per photo, sketch specifications and direction of engineer-in-charge.

Providing and fixing 2 Tier Reagent Racks of size 1100mm(L) x 300mm(W) x 680mm(H):- Reagent Racks shall be complete modular design consisting of 2 stage horizontal storage shelves made of 1.6 mm thick frame. Shelf : Fixed-Type reagent shelves have 1.6mm thickness consisting of 2 stage horizontal storage shelves made of 1.6 mm thick frame of CRCA MS sheet with epoxy powder coating and shall have 4 nos. plates (containing 03 module each) for electrical switches and sockets including necessary wiring etc. It shall have provision for placing Granite pieces. Cutout for 3 module plate to be provided. All the members are knock down and can be restructured. The metal part cutout shall be of 1.00mm thickness. The finish shall be coating of 40-60micron thickness. Load carrying capacity of 70kg for Island table. All the above items shall be as per photo, sketch specifications and direction of engineer-incharge.

ELECTRICAL TRUNKING Providing and fixing Bench Mounted Electrical Trunking. Electrical Trunking body cover shall be of minimum 1.2mm thickness. Used for housing electrical switches and sockets, data and voice points, its top panel, bottom panel of the trunking should be made from minimum of 0.8mm thick body.Bottom plate below trunking to avoid leakage made of 6mm thickness PP sheet It should be available in both, single sided and double sided configurations. It should be made from CRCA MS with pure epoxy powder coating with minimum 50 microns tickness . The front surface that houses the electrical points should have a slope. Size of each unit shall be 220 mm W x 86.5 mm D x 92.5 mm H. All the above items shall be as per photo, sketch specifications and direction of engineer-incharge.

Providing and Placing in position Lab Stools.Overall Sizes Diagonal Leg Dia 538 mm H470 min-655maxTop plate should made of SS 202 made sheet with spin section of thickness 1mm and should be non corrosive. It should have a diameter of 305mm,seat base should made of MS ring and rectangular tube.EN8 Screw having dia of 22 mm should be used for height adjustment of the seat base.The round hub should be made of MS ERW tube having dia of 38mm and thickness 2 mm. The Hub should be welded with the legs and it should accommodate and cover the lead screw mechanism.The understructure should consist of 4 legs made up of MS ERW tube of diameter 25.4 mm and 1.6mm thick. The press formed pipe leg should give a round and clean look. All the legs should be provided with 4 nos of Nylon-6 bush.All metal components should be pre treated with zinc phosphating in 9 tank porcess and then powder coated with anti microbial epoxy polyster powder coating to fulfill the requirements for bacterial protection against at least 2 commonly found bacteria in Hospital environment [Gram positive and Gram Negative].Safe working load must be 135kg

Providing and Placing in position Reading Tables. Providing Desk based system that has been designed to give a richer experience. The system should cater to different work activities with well-equipped layouts and zones created by the system’s different elements. Worktop: Worktop shall be made of 25MM thick Pre-Laminated Board conforming to IS: 12823. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The worktop shall be complete with provisions for screen mounting as well as for wire management on the workstation. Provisions for fixing of the switches shall be on the wire tray/channel. Access flaps with soft closing technology shall be provided on the table tops to access the switch points on the tray. Understructure: The slanted legs shall be connected to the understructure with the help of PDC Connectors to provide a stable and sturdy base for the worktops. Modesty panel shall be of Acrylic (8 mm thick Acrylic both side frosted) or of Metal 1.2 mm thick CRCA. Wire Management: It shall be a part of the understructure and can be in the form of enclosed metal tray or 2 level enclosed channel to provide concealed wire management throughout the cluster formation. Wire riser leg or independent wire risers shall be provided as per the layout structure. Screen: Screen shall be provided as per the requirement of the design and layout. The screen shall be made of 3mm thick MDF Board plus batten made of 12 mm thick MDF Board plus 3 mm thick MDF Board. Honey comb blocks shall be used to fill in the void space. Groove of 3 mm shall be provided on the periphery to accomodate the fabric pasted on either side to be tucked in and allow a PVC flexible T-Mould to give clean edge. Recta - 1800 W mm x 900 D mm x 750 H mm

Providing and Placing in position Reading Tables. Providing Desk based system that has been designed to give a richer experience. The system should cater to different work activities with well-equipped layouts and zones created by the system’s different elements. Worktop: Worktop shall be made of 25MM thick Pre-Laminated Board conforming to IS: 12823. All the edges of work surface shall be provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The worktop shall be complete with provisions for screen mounting as well as for wire management on the workstation. Provisions for fixing of the switches shall be on the wire tray/channel. Access flaps with soft closing technology shall be provided on the table tops to access the switch points on the tray. Understructure: The slanted legs shall be connected to the understructure with the help of PDC Connectors to provide a stable and sturdy base for the worktops. Modesty panel shall be of Acrylic (8 mm thick Acrylic both side frosted) or of Metal 1.2 mm thick CRCA. Wire Management: It shall be a part of the understructure and can be in the form of enclosed metal tray or 2 level enclosed channel to provide concealed wire management throughout the cluster formation. Wire riser leg or independent wire risers shall be provided as per the layout structure. Screen: Screen shall be provided as per the requirement of the design and layout. The screen shall be made of 3mm thick MDF Board plus batten made of 12 mm thick MDF Board plus 3 mm thick MDF Board. Honey comb blocks shall be used to fill in the void space. Groove of 3 mm shall be provided on the periphery to accomodate the fabric pasted on either side to be tucked in and allow a PVC flexible T-Mould to give clean edge. Recta - 900 W mm x 600 D mm x 750 H mm

Providing and Placing in position Chair. The seat and back are made up of injection moulded high impact strength polypropylene polymer with indoor gate UV resistance. The dimensions of Back shall be 51.6cm. (W) X 40.5cm. (H) and of seat shall be 52.5cm. (W) X 53.2cm. (D). The Tubular welded frame is made of made of 3.5±0.03cm x 1.5±0.03cm x 0.12±0.0128cm thk M.S. E.R.W. tube and welded connecting tube made of dia 2.22±0.03cm x 0.12±0.0128cm thk stainless steel 202 grade tube. The tubes are buff polished to give shiny finish. The shoes are made of high impact strength polypropylene polymer compound with indoor grade UV resistance and pressed fitted with tubular frame. An upholstery cover can be retro fitted on to seat and back. The seat cover is made from High abrasion resistance fabric with foam lamination and 2.5cm PU foam insert. The back cover is made from high abrasion resistance fabric with foam lamination and 0.1 cm PU foam insert.

Providing and Placing in position Double Sided Book Rack. Overall size of the rack shall be 1200 W mm x 600 D mm x 2078 H mm. Side panels, Frame and Cross L bracket shall be made using 0.8 mm CRCA. The assembly consists of 2 tie rods, 4 fixing brackets and 2 turnbuckles. The tie rods shall be fixed in a shape of ‘X’. The tie rods shall be made of 4mm diameter rods of MS while fixing brackets shall be made of 2mm thick CRCA. Wooden panel of 25mm thk PLT, E1-P2 grade board shall be provided on sides, edges shall be provided with machine pressed 2 mm thick PVC lipping glued with hot meltEVA glue. Under structure shall be made of 0.8m CRCA. Shelves used shall be 10 bend panel made of 0.8mm CRCA. Shelf panels shall be placed on shelf support and then fixed using nutand bolts from below. It consists of 6 loading levels formed by 5 no ofadjusted shelf. Uniformly Distributed Load Capacity per each shelf shall be 80 Kg maximum. All MS sheetmetal and metal frame components shall be powder coated with epoxy polyester powder to the min thickness of min 45 microns.

Providing and Placing in position Periodical Display Rack. Overall size of the rack shall be 900 mm (W) x 450 mm (D) x 1830 mm(H). Rigid Knockdown construction ,Panels shall be made from CRCA 0.6 mm thick and front frame shall be made from CRCA 0.8 mm thick . CRCA D grade as per IS 513 . There shall be 5 level racks , Display tray shall be suitable for fullscape size magazines,periodicals, aesthetically appealing metal tray at an angle for easy viewing . Receding facility to access the storage behind . Sliding on plastic rollers . Behind storage shelving each of 5 level has a behind storage shelf . Uniformly Distributed Load capacity per each shelf is 40 kg . Leveler shall be screw type with hex plastic base and finish shall be epoxy polyester powder coated to the thickness of 50 microns .

Providing and Placing in position Bookcase. Overall size of the bookcase shall be 914 mm (W) x 320 mm (D) x 1742 mm (H). The unique design provides the right rigidity to the Top hinged doors , which shall facilitate easy use. The Book Case shall be made from prime quality CRCA steel with anti rusting treatment. It shall have a Rigid Knock Down Construction. The Top Pannel, Back Pannel and Side Pannel are made from 0.7mm high yield CRCA and other components from 0.8mm CRCA. Each door shall have a 6 Lever Cam Lock with Common Key. 3mm thick glass should be used in each door for clear inside vision whih shall be secured in a metal frame through a rubber gasket. Scissor Mechanism should be provided in each door for receding inside the top of every compartment and it shall ensure parallel and smooth movement. Each door should be provided with plastic side end caps as handle which is easy to grip. Each compartment shall have a storage shelf with a UDL capacity of max 80 Kg. The 4 Door Book Case shall have metal inside top panel. The finishing shall include Epoxy powder coated to the thickness of 50 microns ( plus /- 10).

Providing and Placing in position Plain Almirah. Overall size of the Almirah shall be 916 mm (W) x 486 mm (D) x 1980 mm (H) with welded construction. It should have the shelf thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. It should have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It shall have 4 no.s full shelves. A4 size box file(85 W x 285 D x 345 H mm) can be stored vertically on three shelves and the clear space above fourth shelf is 240mm. It should also have a M10 Screw type Leveller with Hex plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns ( plus /- 10). There shall be 5 loading levels in the almirah.

Providing and Placing in position Visitors Chair. The cushioned seat assembly shall be made of injection moulded plastic outer and inner. Plastic inner is upholstered with stitched cover and moulded high resiliance polyurethane foam of density 45 plus /- 2 kg/m³ and hardness load of 16 plus /- 2 kgf for 25% compression. The stitched cover shall be made from spacer fabric and leatherette. Seat size shall be 47 cm W x 48 cm D. The cushioned back shall be made of PU foam with insitu molded MS ERW round tube of size 1.9 plus /- 0.03 cm x 0.16 plus /- 0.0128 cm. It shallm be upholstered with spacer fabric and leatherette. The back size shall be 45 cm W x 60.5 cm D. The tubular frame shall be powder coated and shall be cantilever type. It shall be made of Ø2.54 plus /-0.03 cm x 0.2 plus /-0.016 cm thick MS ERW Tube. Back shall be conected to the frame throug powder coated high pressure die casted connector piece.