Public Works Department Tender

Providing and placing mechanically assisted drive mechanism Mobile compactor. The structure shall be made out of 0.8 thick high yield strength CRCA sheet of grade `D` confirming to IS:513. Each unit have 5 loading levels formed by 4 nos. of adjustable shelves. Body units are bolted to undercarriage. Compactor height from ground should be 2125 mm (1980 body plus 145 undercarriage). The body including shelves shall be given antirust surface treatment and powder coated with epoxy polyester powder. It involves an 7 step treatment, Final finish consists of epoxy polyester powder coating of approved color and shade with a Dry Film Thickness of minimum 40 microns. It shall have max. load bearing capacity of 60 Kg uniformly distributed per shelf. Shelves shall be mounted on support brackets and shelf level can be adjusted. The Undercarriage shall be welded frame made of HR sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. A Centralized locking arrangement shall be provided through Locking Stiffener mounted onto back of Single Last unit so that it gets locked on channels when all the units are brought together. This arrangement occupies a space of 100 mm. Each Drive type units have Locking Knob near the Drive wheel for manual locking of individual units when a person is using those units. End stoppers are provided at the end of channels to prevent derailment. The nuts and bolts are galvanized / Zn Plated. Movement of units shall be achieved mechanically through a Drive wheel and ‘Sprocket-Chain-Tensioner’ arrangement mounted rigidly onto body side. Static Body: 7 Twin Body: 12 Last BOdy: 7

Supplying and Placing Modular table in completely knock down conditions with an overall size 2400mm X 2000mm X 750mm that is to be assembled at site. The worktop shall have the size 2400mm X 1000mm made up of 25mm thick Medium Density Fibre-board with approved veneer laminate and PU polish accordingly. The table top profile shall be in rectangle shape with round corners and full round post forming edges. Single sided Flip-up box shall be enclosed at table top that houses telephone cable, data and power connection discretely. The table top shall be supported on MDF board based gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick medium density fibre-board and profile shall be in moulded construction with full round post forming edges and duly deco painted. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick medium density fibre-board in linear shape with appropriate PVC edge banding and veneer laminate. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 1770mm x 510mm X 620mm. It shall have 2 nos. of drawer, 2 nos. of door shutter and 1 nos of sliding shutter. The drawer shall be operated with profile handle and easily close and open with the assistance of sliding channels to enable smooth operation and sliding rail track and concealed crank hinge. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. The complete structure shall be supplied with approved veneer laminate, PU polish and deco painted. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO- 18001:2007, BIFMA membership and AIOTA certification. Make (Wipro/ Geeken/ Spacewood/Godrej /Haworth Only)

Supplying and Placing Modular table in completely knock down conditions with an overall size 2100mm X 1800mm X 750mm that is to be assembled at site. The work top shall have the size 1600mm X 900mm made up of 45mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported on 75mm Peg mounted over side storage unit at one side and fixed pedestal at another side. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 45mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick Pre-laminated particle board in linear shape with appropriate PVC edge banding connected with both end. The table shall have side unit for storage purpose with an overall size 1650mm X 510mm X 625mm. The side unit shall be made up of Pre-laminated particle board of grade II of IS 12823 with top and side 45mm thick and drawer base 9mm thick and other parts 18mm thick like shutter, back, facia, etc. It shall have 3 drawer and 2 sliding shutter. The drawer shall be operated with SS handle and easily close and open with the assistance of roller base channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The top shall be enclosed by single sided flaper box that houses telephone cable, data and power connection discretely. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. A hanging pedestal shall be provided with an overall size 455mm X 510mm X 485mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 2 nos. of drawer operated with SS handle and easily close and open with the assistance of roller and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be locked with one single key. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO- 18001:2007, BIFMA membership and AIOTA certification.

Supplying and Placing Modular table in completely knock down conditions with an overall size 2000mm X 2100mm X 750mm that is to be assembled at site. The worktop shall be 43 mm thick having the combination of 18mm particle board as top and 25mm medium density fibre-board as base top. The top shall have the size 1800mm X 2000mm with approved laminate and shade as well as deco paint. The profile shall be in rectangle shape with round front and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding and base top shall be in half round post forming with grooves. The top shall be supported on 75mm Peg mounted over side storage unit at one end and fixed pedestal unit at another end. The table shall be clad with 9mm thick modesty panel which provide structural support for the table having round profile in middle section and linear on both left and right with appropriate PVC edge banding connected with both end on side unit and fixed drawer with 25mm round spacer. The table shall have side unit for storage purpose with an overall size 1800mm X 500mm X 640mm. It should be made up of Pre-laminated particle board of grade II of IS 12823 with top 25mm thick and other parts 18mm thick like shutter, back, facia, side panel etc. It shall have 2 drawer and 1 shutter. The drawer shall be operated with SS handle and easily close and open with the assistance of roller channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The side storage unit shall be mounted on 75mm Peg. A pedestal shall be provided with an overall size 500mm X 750mm X 640mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, facia shall be 18mm thick, top 25mm and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer. The drawer shall be operated with SS handle and easily close and open with the assistance of roller channel and central locking mechanism in which all the drawer shall be synchronized

Supplying and Placing Modular table in completely knock down conditions with an overall size 1800mm X 2000mm X 750mm that is to be assembled at site. The worktop shall have the size 1800mm X 800mm made up of 25mm thick Pre laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. Single sided flaper box shall be enclosed at table top that houses video, audio, data and power connection discretely. The table top shall be supported on CRCA powder coated rectangle pipe having cross-section area 40mm X 20mm with 1.6mm thick. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 18mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding covered by CRCA powder coated loop leg having cross-section area 60mm X 30mm. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre- laminated particle board in linear shape with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table shall have side unit for storage purpose with an overall size 1200mm X 450mm X 600mm. The side unit shall be made up of Prelaminated particle board of grade II of IS 12823 with top 25mm thick, base 9mm thick and other parts 18mm thick like shutter, back, side panel etc. It shall have 2 sliding shutter which slides over sliding rail track. The shutter shall be operated by SS handle. The side unit shall be mounted over injection moulded nylon castor. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 650mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos.

Overall size of Personal Locker Unit with add on units shall be of dimensions 1520mm(W) X 450mm(D) X 1800mm(H) having 16 locker unit. Stackability shall have add - on units that can be stacked width wise to form bank of lockers having common side panel. Locking shall have cam lock with lock lever plus option. Material shall be CRCA 0.8 mm thickness. Shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum. Finish shall be epoxy polyester powder coated to the thickness of 50 microns. Handle/Label holder shall be aesthetically appealing Snap fit ABS plastic handle. Ventilation shall be attractive punched pattern for ventilation.

Providing and placing workstation table in completely knock down conditions with an overall size 1320mm X 660mm X 1200mm that is to be assembled at site. The work top shall have the size 1200mm X 600mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 525mm X 350mm. The trey shall be operated on keyboard channel. The workstation shall have panel based partition of 60 mm thick with overall height 1200mm. The partition shall be linear in profile and provided in the front side of user as well as on the both sides of the user. The top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with 40µ-60µ thick. The trims shall have the size 60mm X 19mm with 1.5mm thick covered with Die cast end caps on joints 2 ways, 3 ways and 4 ways (L-cover for corner, T-cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(H) X 60mm(D) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) and marker board provided at front of the user. Laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. The Partition shall have concealed wire management capabilities and should be engaged for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs

Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The complete structure shall be upholstered with leatherite tapestry 1±0.2 mm thick and 571 GSM. The understructure shall consist of SS 202 grade loop leg with shiny chrome finish having cross-section area 40mm X 20mm with 1.6mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 1040±10 mm(W), seat height = 435±10 mm, overall width = 1900±10 mm, overall depth = 770±10 mm and overall height = 800±10 mm.

Providing and supplying a high back chair with ergonomic design, comfortable and aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (30 plus 25)mm thick having density (40 and 32)kg/m³ and the back shall be made of (15 plus 6)mm thick double layered moulded plywood padded with high resilience polyurethane foam 30mm thick having density 32kg/m³. The same shall be upholstered with leatherite tapestry 1mm thick and 571 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support and full back support as well as head support. The chair shall be supplied with chrome plated arm with cushion having leatherite covering top. For seating durability the chair shall have knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti- shock feature which provides back strength for the chair. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged MS CRCA chrome plated having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair shall be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standards tested to perform 98,000 cycles with 250lbs load. The seat size shall be 515±10 mm(D) X 545±10 mm(W) and back size shall be 560±10 mm(W) X 700±10 mm(H) from seat. Overall height shall be = 1155±10 mm, overall depth/width = 760±10 mm. Make (Wipro/ Geeken/ Spacewood/Godrej /Haworth Only)

Providing, supplying and placing steel almirah in perfectly upright and straight position. The overall size of the almirah shall be 915mm (W) X 485mm (D) X 1980mm (H) including legs. It should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. Door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. Stiffeners shall be provided in shelf and door. The steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity per each shelf shall be 40kg maximum. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 40-60µ.

Supplying and Placing Modular table in completely knock down conditions with an overall size 1500mm X 1650mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall have the size 1500mm X 750mm made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The side top shall have the size 900mm X 450mm X 750mm with 25mm thick Pre-laminated particle board. The table top profile shall be in rectangle shape with one side round and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board. The trey shall be operated on keyboard channel. The table top and side top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the bottom to avoid scratches on the floor. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with handle and easily close and open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. A movable type CPU unit shall be provided. It should be made up of 18mm thick particle board. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO- 14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification.

Supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and having density 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam thick having density 32Kg/m³. SS strip shall be provided on front of the arm having length 515mm with cross-section area 14mm X 4mm. The structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have shiny chrome finish SS leg with height 100mm and 10mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 500±10 mm(D) X 1480±10 mm(W), seat height = 430±10 mm, overall width = 1625±10 mm, overall depth = 750±10 mm and overall height = 700±10 mm.

Providing and supplying visitor chair with ergonomic design for user comfort and aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (30 plus 25)mm thick having density (40 and 32)kg/m³ and the back shall be made of (15 plus 6)mm thick double layered moulded plywood padded with high resilience polyurethane foam 30mm thick having density 32kg/m³. The same shall be upholstered with leatherite tapestry 1mm thick and 571 GSM. The backrest shall be made by keeping the natural curvature of the spine for back support. The chair shall be supplied chrome plated fixed arm with cushion having leatherite covering top and seat and back shall be arrested together with powder coated HR steel spine. The frame structure shall be cantilever support type made of MS CRCA chrome plated capsule pipe of size 40mm X 20mm with 1.6mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 545±10 mm(W) and back size shall be 560±10 mm(W) X 520±10 mm(H) from seat. Overall height shall be = 990±10 mm, overall depth = 660±10 mm and overall width = 680±10 mm. Make (Wipro/ Geeken/ Spacewood/Godrej /Haworth Only)

Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and having density 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam thick having density 32Kg/m³. SS strip shall be provided on front of the arm having length 515mm with cross-section area 14mm X 4mm. The structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have shiny chrome finish SS leg with height 100mm and 10mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 500±10 mm(D) X 1015±10 mm(W), seat height = 430±10 mm, overall width = 1160±10 mm, overall depth = 750±10 mm and overall height = 700±10 mm.

Supplying and Placing executive table in completely knock down conditions with an overall size 1050mm X 600mm X 750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall be made up of 25mm thick particle board with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape with front and back full round post form edges and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. A pullout keyboard trey shall be provided of 18mm thick Pre-laminated particle board having size 550mm X 280mm. The trey shall be operated on keyboard channel. The table top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. It should be made up of 25mm thick Pre-laminated particle board and profile shall be in linear shape with front and back full round post form edges and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. A mobile pedestal shall be provided with an overall size 400mm X 400mm X 650mm. The pedestal shall be made up of Pre- laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close and open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. A movable type CPU unit shall be provided with an overall size 468mm X 284mm. The CPU unit shall be made up of 18mm thick Prelaminated particle board. The manufacturer shall have quality and safety assurance like ISO- 9001:2015, ISO- 14001:2015 and ISO-18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screw- withdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supplying and placing center table with an overall size 1200mm X 600mm X 450mm. The top shall be made up of 12mm thick toughened glass. The profile shall be in rectangle shape with bevelled edges. The bottom storage shelf shall be provided with an overall size 1155mm X 280mm made of 8mm thick toughened glass with bevelled edges. The glass shall be supported on vacuum caps situated over SS 202 grade pipe frame. The under structure shall have SS pipe frame having size 67mm X 13.5mm. There shall be PPCP shoe provided to avoid scratches on the floor.

Providing and supplying a high back chair with ergonomic design, comfortable and aesthetically appealing. The seat and back shall be made up of 18mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (40 plus 30)mm thick having density (32 and 32)kg/m³ in seat and (40 plus 30)mm thick having density (32, 32)kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine for lumbar support which helps to provide full back support as well as head support. The chair shall be supplied with polypropylene arm with cushion base leatherite covering top. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged MS CRCA powder coated with 40-60µ thick having pitch circle dia. 600 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 480±10 mm(D) X 520±10 mm(W) and back size shall be 540±10 mm(W) X 710±10 mm(H) from seat. Overall height shall be = 1140±10 mm, overall depth/width = 700±10 mm.

Providing, supplying and placing an open display book racks. The overall size of the rack shall be 925mm (W) X 300mm (D) X 1800mm (H). The rack shall be supplied with 4 nos. of adjustable shelves i.e. 5 loading levels. Rack, side panel, skirting shall be made of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. Side and top shall be covered with 18mm thick Pre-laminated particle board of grade II of IS 12823. The edges of the board shall be sealed with 2mm thick PVC edge banding. The add-on units can be stacked width wise to form a bank of racks having common panel. Back panel up to the bottom of third rack shall have additional rigidity. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity per each shelf shall be 80 kg maximum. Each rack shall be provided with stiffener at bottom for strength. Label holder and range indicators on each main unit for inserting labels. All steel components shall be epoxy polyester powder coated to the thickness of 40-60µ. Adjustable leveler shall be provided with metal insert to resist scratches on the floor and also level and support structure.

Supplying and placing café table with an overall size 1200mm X 600mm x 750mm. The top of the table shall be made up of 18mm thick rubber-wood top. The top profile shall be in rectangle shape with taper edges. The top shall be supported on MS chrome plated pipe frame in X shape having length 300mm (1 nos.) and 225mm (4 nos.) with cross- section area 30mm X 15mm. The table understructure shall have 2 nos. round pole of dia. 50.8mm with 660mm length. The base plate shall be made of MS powder coated having size 700mm X 395mm in elliptical oval shape. The manufacturer shall have quality and safety assurance like ISO 9001:2008, ISO 14001:2004 and ISO 18001:2007.

Supplying and placing storage unit with an overall size 1800mm X 450mm X 750mm. It should be made up of Pre- laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The top of the shutter shall be 25mm thick and all other profile i.e. side, back, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 2 nos. of adjustable shelf and 4 nos. of sliding shutters shall be provided for ease of opening. The sliding shutter shall be operated on sliding rail track and SS handle as well as push lock mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the bottom to avoid scratches on the floor. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO- 18001:2007, BIFMA membership and AIOTA certification. The boards used should meet international standards of quality and safety, Indian standard IS 12823 grade II should meet long time load bending, screw-withdrawal strength, modulus of elasticity bending tested as per IS 2380.

Supplying and placing single seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded separately. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 32Kg/m³. SS strip shall be provided on front of the arm having length 515mm with cross-section area 14mm X 4mm. The structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM. The understructure shall have shiny chrome finish SS leg with length 100mm and 10mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 500±10 mm(D) X 545±10 mm(W), seat height = 430±10 mm, overall width = 690±10 mm, overall depth = 750±10 mm and overall height = 700±10 mm.

Supplying and placing single bed with an overall size 2060mm (L) x 1131 (B) x 930mm (H). Head and tail panel shall be made of 18mm thick Pre laminated particle board and baton shall be made of 32mm thcik MDF board duly bull nose shape. Sides baton shall be made of 32mm thick MDF board (one side full round post forming) and 18mm thick particle board with 2mm thick PVC edge banding . The edge banding shall be pasted with hot melt glue at 200 degree Celsius. Mattress panel shall be made of 18 mm thick particle board. The understructure shall consist of MS channles in 1mmm thickness. Horizontal and Bottom Plinth shall be made of 25mm thick Pre laminated particle board.

Supplying and placing center table with an overall size 1200mm X 600mm X 450mm. The top of the table shall be made up of 12mm thick toughened glass with bevelled edges. The profile shall be in rectangle shape with round corner. The top shall be supported on MS chrome plated tubular frame with cross-section area 40mm X 20mm with 1.6mm thick. The under structure shall consist of four legs made of MS chrome plated oval pipe having cross-section area 52mm X 26mm with 1.6mm thick. There shall be co-polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. Make (Wipro/ Geeken/ Spacewood/Godrej /Haworth Only)

Supplying and placing ergonomically designed, comfortable and aesthetically appealing High back chair. The seat shall be made of 15mm thick hot pressed plywood upholstered with high resilience polyurethane foam 40mm thick having density 40kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM and the back shall be supported by MS CRCA metal frame upholstered with high resilience polyurethane foam 19mm thick having density 23kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine. The seat and back shall be individual with different plywood and metal frame and the armrest shall be used MS CRCA chrome plated PU arm completely joint with seat and back. The chair shall have knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 120mm with BIFMA standard class-3 gaslift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal shall be made up of MS CRCA chrome plated having pitch circle Dia 650 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with BIFMA standards. The Seat size shall be 490±10 mm(W)X500±10 mm(D) and back size shall be 685±10 mm(H) from seat and overall height = 1145±10 mm.

Supplying and placing ergonomically designed, comfortable and aesthetically appealing High back chair. The seat shall be made of double layered moulded (18 plus 6)mm thick hot pressed commercial plywood upholstered with high resilience polyurethane foam (40 plus 30)mm thick having density 40kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM and the back shall be made of double layered moulded hot pressed plywood (18 plus 6)mm thick upholstered with high resilience polyurethane foam (30 plus 25)mm thick having density 32kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine.. The seat and back shall be fixed with plywood and the armrest shall be used metal base chrome finish cushion arm with leatherite tapestry completely joint with seat and back. The chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 65mm with BIFMA standard class-3 gas- lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal shall be made up of MS CRCA chrome plated having pitch circle Dia 700 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self-lubricating property for friction free movemen with BIFMA standards. The seat size shall be 500±10 mm (D) X 480±10 mm (W) and back size shall be 520±10 mm (W) X700 ±10 mm (Ht) from seat. Overall height shall be = 1160±10 mm, overall depth = 700±10 mm and overall width = 650±10 mm.

Supplying and Placing conference table in completely knock down conditions per seat size 675mmx 600mm x750mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The worktop shall be made up of 25mm thick prelaminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The connecting top shall be made up of 25mm thick Medium density fibre-board with deco painted. The table top profile shall be in rectangle shape with round corners with full round post forming edges at front and back and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported on particle board base gable end and metal pole leg. The end wall of the table on the side shall be topped by gable end. It should be 25mm thick Pre-laminated particle board and profile profile shall be in linear shape with front and back full round post form edges and other edges sealed with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the bottom to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. The manufacturer shall have quality and safety assurance like ISO-9001:2015, ISO-14001:2015 and ISO- 18001:2007, BIFMA membership and AIOTA certification. The board used should meet International Standard of quality, Indian standard IS 12823 grade II should meet long time load bending, screwwithdrawal strength, modulus of rupture and modulus of elasticity bending tested as per IS 2380.

Supplying and placing center table with an overall size 450mm X 450mm X 450mm. The top of the table shall be made up of 12mm thick toughened glass. The top profile shall be in square shape with round corner and the edges shall be in chamfer shape. The top shall be supported on MS chrome plated oval frame with crosssection area 40mm X 20mm with 1.6mm thick. The under structure shall consist of four legs made of MS chrome plated oval pipe having cross- section area 52mm X 26mm with 1.6mm thick. There shall be copolymer polypropylene shoe provided at the bottom to avoid scratches on the floor.

Providing and supplying a visitor chair with ergonomic design for user comfort and aesthetically appealing. The seat and back shall be made of 18mm thick hot pressed commercial plywood padded with high resilience polyurethane foam (40 plus 30)mm thick having density (30, 32)kg/m³ in seat and (40 plus 30)mm thick having density (32, 32)kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine for back support. The chair shall be supplied with polypropylene arm with cushion base leatherite covering top. The frame structure shall be cantilever support type made of MS CRCA powder coated 50-60µ (DFT) thick round pipe of dia. 28.5mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The Seat size shall be 480±10 mm(D) X 520±10 mm(W) and back size shall be 540±10 mm(W) X 600±10 mm(H) from seat. Overall height shall be = 1055±10 mm, overall depth = 640±10 mm and overall width = 660±10 mm.

Supplying and placing ergonomically designed, comfortable and aesthetically appealing High back chair. The seat shall be made of 15mm thick hot pressed curved plywood upholstered with high resilience polyurethane foam 50mm thick having density 40kg/m³ with khaki leatherite tapestry 0.8mm thick and 535 GSM and the back shall be supported by metal insert MS CRCA frame upholstered with high resilience polyurethane foam 12mm thick having density 23kg/m³ with khaki leatherite tapestry 0.8mm thick and 535 GSM with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine. Headrest shall be provided for comfort of head with leatherite tapestry. The armrest shall be used MS CRCA chrome plated with PU arm completely joint with seat and back. The chair shall have knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 100mm with BIFMA standard class-3 gaslift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal shall be made up of MS CRCA chrome plated having pitch circle Dia 640 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with BIFMA standards. The Seat size shall be 485±10 mm(W)X520±10 mm(D) and back size shall be 740±10 mm(H) from seat, overall height = 1150±10 mm and overall depth/width= 740±10mm.

Providing and supplying a medium back chair with ergonomic design, comfortable and aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with inserted pipe frame. The chair shall be padded with high resilience polyurethane foam 50mm thick having density 40Kg/m³ in seat and 12mm thick having density 23Kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 GSM and breathable mesh tapestry behind the backrest. MS chrome plated pipe frame shall be provided on both side of seat and back with size 25mm X 10mm. The backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support. The armrest shall be used black integral polyurethane arm mounted on CRCA chrome plated pipe having size 40mm X 10mm completely joint with seat and back with the assistance of Allen key screw. A chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal shall have five legged CRCA chrome plated having pitch circle dia. 650mm fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled, confirming to ANSI/BIFMA Standards X5.1- 2011 tested to perform 98,000 cycles with 250lbs load. The Seat size shall be 490±10 mm(W) X 520±10 mm(D) and back size shall be 450±10 mm(W) X 535±10 mm(H) from seat and overall height = 980±10 mm, overall width = 560±10 mm and overall depth = 670±10 mm.

Supplying and Placing Visitor Chair ergonomically designed for user comfort and shall have asthetically appealing design. The seat shall be made of double layered moulded hot pressed plywood (12 plus 6)mm thick upholstered with high resiliance polyurethane foam (40 plus 30)mm thick having density 40kg/m³ with black leatherite tapestry 0.8mm thick and 535 GSM and the back shall be made of double layered moulded hot pressed plywood (12 plus 6)mm thick upholstered with high resiliance polyurethane foam (32 plus 25)mm thick having density 32kg/m³ with black leatherite tapestery 0.8mm thick and 535 GSM with lumbar support. The seat and back shall be fixed with L-type plywood and the armrest shall be used metal base chrome plated cushion arm completely joint with seat and back. The frame structure shall be cantilever support type made up of MS CRCA chrome plated round pipe of Dia 28.5mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The Seat size shall be 500 ±10 mm(D)X500±10 mm(W) and back size shall be 500 ±10 mm(W)X 560±10 mm(Ht) from seat. Overall height shall be = 1000 ±10 mm, overall depth = 700±10 mm and overall width = 610±10 mm

Providing and supplying visitor chair with ergonomic design for user comfort. The seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resiliance polyurethane foam 40mm thick having density 40kg/m³ with leatherite tapestry 0.8mm thick and 535 GSM and the back shall be made of MS CRCA metal frame upholstered with high resiliance polyurethane foam 19mm thick having density 23kg/m³ with leatherite tapestry 0.8mm thick and 535 GSM. The backrest of the chair shall be made by keeping the natural curvature of the spine with lumbar support. The seat and back shall be arrested together with CRCA chrome plated rectangle pipe frame having cross-section area 40mm X 10mm with 1.6mm thick and the armrest shall be used polyurethane arm mounted on CRCA pipe frame having crosssection area 40mm X 10mm with 1.6mm thick. The frame structure shall be cantilever support type made up of MS/CRCA chrome plated oval pipe having cross-section area 40mm X 20mm with 2mm thick. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor. The seat size shall be 480±10 mm(W) X 480±10 mm(D) and back size shall be 510±10 mm(H) from seat and overall height = 980±10 mm.

Providing and supplying high back chair with ergonomic design, comfortable and aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 45kg/m³ in seat and 45mm thick having density 35Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ABS moulded cover and the backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polyurethane arm with metal insert completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in black 30% glass filled nylon having pitch circle dia. 700±15 mm and fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA Standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 485±10 mm(W) X 450±10 mm(D) and back size shall be 490±10 mm(W) X 610±10 mm(H) from seat. Seat height 460±10 mm, overall height shall be 1060±10 mm, overall depth = 620±10 mm and overall width (Arm) = 600±10 mm, Overall base dia. 760±10 mm.

Providing and supplying a visitor chair with ergonomic design for user comfort and shall have aesthetically appealing. The seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with metal pipe, inserted between backrest. The chair shall be padded with high resilience polyurethane foam 50mm thick having density 40kg/m³ in seat and 12mm thick having density 23Kg/m³ in back. The seat and back shall be upholstered with leatherite tapestry 0.8±0.1mm thick, 535 GSM and breathable mesh tapestry behind the backrest. MS chrome plated pipe frame shall be provided on both side of seat and back with size 25mm X 10mm. The backrest shall be supplied by keeping the natural curvature of the spine which helps to provide back support. The armrest shall be used black integral polyurethane arm mounted on CRCA chrome plated pipe having size 40mm X 10mm completely joint with seat and back with the assistance of Allen key screw. Chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. The frame structure shall be cantilever support type made of MS CRCA chrome plated round pipe of dia. 25.4mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 500±10 mm(W) X 510±10 mm(D) and back size shall be 450±10 mm(W) X 540±10 mm(H) from seat and overall height = 980±10 mm, overall width = 560±10 mm.

Providing and supplying high back chair with ergonomic design, comfortable and aesthetically appealing. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of the chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine with lumbar support. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polyurethane arm with metal insert completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should be five legged injection moulded in black 30% glass filled nylon having pitch circle Dia. 700±15 mm and fitted with 5 nos. twin wheel castors. The castors of the chairs should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA Standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 475±10 mm(W) X 460±10 mm(D) and back size shall be 470±10 mm(W) X 610±10 mm(H) from seat. Overall height shall be = 1050±10 mm, Overall width (arm) = 545±10 mm, base width/ depth = 760±10 mm.

Providing and supplying mid back chair. The seat shall be made of 15mm thick hot pressed plywood upholstered with high resilience polyurethane foam 50mm thick having density 40kg/m³ with fabric tapestry 0.6mm thick and 235 GSM and the back shall be made of injection moulded polypropylene net cover upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine and the armrest shall be used polypropylene arm completely joint with seat and back. For seating durability the chair shall have swivel tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The pedestal should have five legged injection moulded in 30% glass filled black nylon having pitch circle Dia. 620 mm fitted with 5 nos. twin wheel castor. The castors of the chair should be injection moulded in black nylon 30% glass filled, confirming to ANSI/BIFMA X5.1-2011 standard tested to perform 98,000 cycles with 250lbs load. The seat size shall be 475±10 mm(W) X 490±10 mm(D) and back size shall be 450±10 mm(W) X 530±10 mm(H) from seat. Overall height shall be = 885±10 mm and overall width/ depth = 720±10 mm.

Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 45kg/m³ in seat and 45mm thick having density 35Kg/m³ in back. The same shall be upholstered with fabric tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene/ABS moulded cover and the backrest shall be made by keeping the natural curvature of the spine. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used black integral polyurethane arm with metal insert completely joint with seat and back. The frame structure shall be cantilever support type made up of MS/CRCA powder coated with 50-60µ (DFT) thick round pipe of dia. 25.4mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The seat size shall be 480±10 mm(W) X 450±10 mm(D) and back size shall be 480±10 mm(W) X 400±10 mm(H) from seat and overall height = 820±10 mm.

Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be made of 15mm thick hot pressed commercial plywood padded with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ in seat and 40mm thick having density 40Kg/m³ in back. The same shall be upholstered with tapestry 1mm thick and 300 GSM. The back and base of chair shall be supplied with polypropylene bead on edges and the backrest shall be made by keeping the natural curvature of the spine. The seat and back shall be arrested together with 50-60µ thick powder coated HR steel spine and the armrest shall be used of black integral polyurethane arm with metal insert completely joint with seat and back. The frame structure shall be cantilever support type made up of MS/CRCA powder coated round pipe of Dia. 25.4mm with 2mm thick. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor. The seat size shall be 460±10 mm(W) X 450±10 mm(D) and back size shall be 460±10 mm(W) X 400±10 mm(H) from seat. Seat height = 450±10 mm, Overall height shall be = 830±10 mm, Overall width - 555±10 mm, overall depth = 595±10 mm.

Supplying and Placing cafe chair. The complete structure shall be made up of 20% glass filled injection moulded polypropylene. The frame structure shall be supported by four legs made up of polypropylene having Dia. 35mm at upper and 25mm at lower i.e taper shape. The seat size shall be 410±10 mm(D) X 400±10 mm(W) and back size shall be 390±10 mm(W) X 420±10 mm(H) from seat. Overall height shall be = 845±10 mm, overall depth = 510±10 mm.