Public Works Department Tender

[4.32]Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

[6.1.6]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 6. 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

[6.25.1]Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. 1. All works up to plinth level

[6.25.2]Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. 2. All works above plinth level up to floor IV level

[6.27]Extra for R.C.C./ B.M.C/ R.M.C. work above floor IV level for each three floors or part thereof.

[6.30.1]Centering and shuttering including strutting, propping etc. and removal of form for 1. Foundations, footings, bases of columns, etc. for mass concrete

[6.33.3]Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level 3. Cold twisted bars

[6.33.4]Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level 4. Hot rolled deformed bars

1 Providing and fixing Building Branding Signage `Signage is made of 3D channel Letter, made from Following A) Front :- Front is to be made of 3.5 mm Acrylic and 3M/Avery/LG Cast vinyl (90 micron and minimum 6 year product life)of desired shade as per approval. Dual color vinyl film in desired day shade to be of cast acrylic without prininting the face of vinyl. B) Side :- Signage made of CNC channel bending machine made of exturded alloy 6063 thickness of 1.00mm confirming to BS 1474-1987 . 125 to 130 mm as side of 3D letter exturded alloy profile with front edge and border with provisioning of housing front Acrylic inside . Back of the extrusion must be provided with built in weather proof layer to prevent dust , moisture etc. Alloy to be anodize to 18 to 20 microns in copper/ bronze/ silver colour of approval shades. C) Illumination :- Signage is to be illuminated with LED module base LED with 10000 kelvin made of OSRAM (with required power supplies). D) Back :- Back is to be made of 4mm thick ACP with 0.5 mm thickness Aluminum Foil on both sides. E) Timer:- Auto operated using LandT/Havells/schneider timer of required capacity. Maximum height and width of the words after placement of all letter in single Row to be measured (matras to be excluded from the measurment). BRAND/MAKE- 247SIGN/ ASB Neon/ Vista ` a PROJECT NAME (HINDI and ENGLISH)

Providing and fixing Ms frame work with exterior grade ACP Cladding.

Providing and fixing Entry Gate Signage Providing and fixing External Signage`s made of SS 304 (brush finish) 1mm thk.sheet for Logo and letters with raising(letter depth of 50mm). Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated/hollow illuminated either back or front of the signage to be made of 4 mm thick acrylic. 3M/Avery/LG cast vinyl (90 micron and minimum 6 year product life ) for desired colour with OSRAM make LEDS with 10000 kelvin and IP 67 Grade powersupply fixed on the wall with necessary fixtures. MAIN GATE NAME (HINDI and ENGLISH)

Providing and fixing Entry Gate Signage Providing and fixing External Signage`s made of SS 304 (brush finish) 1mm thk.sheet for Logo and letters with raising(letter depth of 50mm). Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated/hollow illuminated either back or front of the signage to be made of 4 mm thick acrylic. 3M/Avery/LG cast vinyl (90 micron and minimum 6 year product life ) for desired colour with OSRAM make LEDS with 10000 kelvin and IP 67 Grade powersupply fixed on the wall with necessary fixtures. LOGO

Providing and fixing Campus Directional Signage `Double Sided Signage will be fabricated using ACP panel size 800x1200 as base duly fixed over modular aluminium extruded ultraedge section frame of 50mm depth of brand 247Sign/Vista Systems/ASB Neon having no screws visible outside powder coated to 40-50 microns. Text and Graphics will be in 3M grade 11 grade prismatic Retro-reflective self adhesive sheet duly digitally plotter cut and pasted on base on both side as per design. Signage will be grouted to RCC pedestal using MS Pole of 100X100x3000 mm with base plate size 300x300x10 mm duly powder coated of 40-50 microns in approved shade. BRAND /MAKE of modular alloy:- 247SIGN/ ASB NEON/ VISTA SYSTEMS` Directional Signages

Providing and fixing Traffic regulatory Signage ( Drop off/ Speed Limit / No Horn/ BASEMENT Entry/Exit) `A)POST :- Signage is to be made oF 100x100 mm 1800 mm High MS pole, Base Plate of size 250x250mm of thickness 10mm is to be used. Duly powder coated 50 microns in the desired colour. B) Panel-1 :- Panel size 400X110X1200 mm is to be made of 50x50x2 mm internal MS frame duly powder coated to 40-50 microns with ACP 4 mm thick, 0.5 mm aluminium foil, 3M / AVERY grade 11 Prismatic Retro reflective sheet and approved color Overlay film on top having desired text and pictographs on both side post. C) Panel-2 :- Panel size 600X600 Sq/round with ACP 4 mm thick, 0.5 mm aluminium foil, 3M / AVERY grade 11 Prismatic Retro reflective sheet and approved color Overlay film on top having desired text and pictographs. BRAND /MAKE of modular alloy:- 247SIGN/ ASB Neon/ VISTA SYSTEMS` Drop off/ Speed Limit / No Horn/ BASEMENT Entry/Exit

Providing and fixing TOTEM SIGNAGE `A) INTERNAL FRAME- Fabricated out of 75mm ISMC with cross supports and frame for alloy made of 50x50x2 mm MS SHS. Structure shall be duly surface treated with primer and two coats of Enamel paint. B) CORNER PROFILE - Made of 75x19 mm Extruded 6063 alloy of minimum 2mm wall thickness with anodising in dark colour of Brand 247SIGN/ VISTA/ COSIGN C) FRONT and BACK - ACP of approved colour 4mm thick having .45mm aluminium foil of both side, duly housed in the corner Profile. Text and Pictographs CNC cut in the ACP. D) LOGO plus TEXT - 3D letters with translucent vinyl of make 3M/LG/AVERY (90 micron and 6 years minimum product life )on 10mm acrylic, 5mm inside and 5mm outside of ACP same to be illuminated used LEDs of OSRAM with 10000 kelvin . E) SIDES - Sides of Totem 300mm width to have white/ approved color illumination flowing. F) ILLUMINATION - The lighting for Totem shall be acheived throgh OSRAM make LEDs with 10000 kelvin and IP67 Grade power supply. G) BASE PLATE - Base plate of size 400x400mm twin plates of thickness 10mm in to be used. Brand 247SIGN/ COSIGN/ VISTA ` Double side TOTEM

Providing and fixing Entry/ Exit Signage - Wall / Surface Mounted (IN/OUT/NO ENTRY/ NO EXIT) Signage sides is to be made of 50 mm width, extruded alloy 6063 of brand 247Sign/Vista/Cosign having no screws visible outside. duly anodized 18-20 microns bronze / copper finish with in built in provision to received the sign face panel in 5 mm Acrylic on front and having provoison of hold the LED Modules 10000 kelvin . Sign face is to be made of graphic plotter cut vinyl 90 micron and minimum 6 year product life as per graphic pasted over 5 mm thick white transluent acrylic. The panel should be made easily openable for maintinace point of view. Illumination:- The lighting for panel shall be achieved through OSRAM make LEDs with 10000 kelvin and IP 67 Grade powersupply. IN/OUT/NO ENTRY/ NO EXIT

1 Providing and fixing Building indentification Signage `Signage is made of 3D channel Letter, made from Following A) Front :- Front is to be made of 3.5 mm Acrylic and 3M/Avery/LG Cast vinyl(90 micron and minimum 6 year product life) of desired shade as per approval. Dual color vinyl film in desired day shade to be of cast acrylic without prininting the face of vinyl. B) Side :- Signage made of CNC channel bending machine made of exturded alloy 6063 thickness of 1.00mm confirming to BS 1474-1987 . 125 to 130 mm as side of 3D letter exturded alloy profile with front edge and border with provisioning of housing front Acrylic inside . Back of the extrusion must be provided with built in weather proof layer to prevent dust , moisture etc. Alloy to be anodize to 18 to 20 microns in copper/ bronze/ silver colour of approval shades. C) Illumination :- Signage is to be illuminated with LED module base LED made of OSRAM with 10000 kelvin (with required power supplies). D) Back :- Back is to be made of 4mm thick ACP with 0.5 mm thickness Aluminum Foil on both sides. E) Timer:- Auto operated using LandT/Havells/schneider timer of required capacity. F) ACP cladding is to be made of 4mm with 0.5 mm thickness Aluminum Foil on both sides.and ms frame used 37X37 SHS.Dully primer enamel paint. BRAND/MAKE- 247SIGN/ ASB Neon/ Vista ` a OPD (ENGLISH and HINDI)

1 Providing and fixing Building indentification Signage `Signage is made of 3D channel Letter, made from Following A) Front :- Front is to be made of 3.5 mm Acrylic and 3M/Avery/LG Cast vinyl(90 micron and minimum 6 year product life) of desired shade as per approval. Dual color vinyl film in desired day shade to be of cast acrylic without prininting the face of vinyl. B) Side :- Signage made of CNC channel bending machine made of exturded alloy 6063 thickness of 1.00mm confirming to BS 1474-1987 . 125 to 130 mm as side of 3D letter exturded alloy profile with front edge and border with provisioning of housing front Acrylic inside . Back of the extrusion must be provided with built in weather proof layer to prevent dust , moisture etc. Alloy to be anodize to 18 to 20 microns in copper/ bronze/ silver colour of approval shades. C) Illumination :- Signage is to be illuminated with LED module base LED made of OSRAM with 10000 kelvin (with required power supplies). D) Back :- Back is to be made of 4mm thick ACP with 0.5 mm thickness Aluminum Foil on both sides. E) Timer:- Auto operated using LandT/Havells/schneider timer of required capacity. F) ACP cladding is to be made of 4mm with 0.5 mm thickness Aluminum Foil on both sides.and ms frame used 37X37 SHS.Dully primer enamel paint. BRAND/MAKE- 247SIGN/ ASB Neon/ Vista ` b IPD (ENGLISH and HINDI)

1 Providing and fixing Building indentification Signage `Signage is made of 3D channel Letter, made from Following A) Front :- Front is to be made of 3.5 mm Acrylic and 3M/Avery/LG Cast vinyl(90 micron and minimum 6 year product life) of desired shade as per approval. Dual color vinyl film in desired day shade to be of cast acrylic without prininting the face of vinyl. B) Side :- Signage made of CNC channel bending machine made of exturded alloy 6063 thickness of 1.00mm confirming to BS 1474-1987 . 125 to 130 mm as side of 3D letter exturded alloy profile with front edge and border with provisioning of housing front Acrylic inside . Back of the extrusion must be provided with built in weather proof layer to prevent dust , moisture etc. Alloy to be anodize to 18 to 20 microns in copper/ bronze/ silver colour of approval shades. C) Illumination :- Signage is to be illuminated with LED module base LED made of OSRAM with 10000 kelvin (with required power supplies). D) Back :- Back is to be made of 4mm thick ACP with 0.5 mm thickness Aluminum Foil on both sides. E) Timer:- Auto operated using LandT/Havells/schneider timer of required capacity. F) ACP cladding is to be made of 4mm with 0.5 mm thickness Aluminum Foil on both sides.and ms frame used 37X37 SHS.Dully primer enamel paint. BRAND/MAKE- 247SIGN/ ASB Neon/ Vista c Emergency

1 Providing and fixing Building indentification Signage `Signage is made of 3D channel Letter, made from Following A) Front :- Front is to be made of 3.5 mm Acrylic and 3M/Avery/LG Cast vinyl(90 micron and minimum 6 year product life) of desired shade as per approval. Dual color vinyl film in desired day shade to be of cast acrylic without prininting the face of vinyl. B) Side :- Signage made of CNC channel bending machine made of exturded alloy 6063 thickness of 1.00mm confirming to BS 1474-1987 . 125 to 130 mm as side of 3D letter exturded alloy profile with front edge and border with provisioning of housing front Acrylic inside . Back of the extrusion must be provided with built in weather proof layer to prevent dust , moisture etc. Alloy to be anodize to 18 to 20 microns in copper/ bronze/ silver colour of approval shades. C) Illumination :- Signage is to be illuminated with LED module base LED made of OSRAM with 10000 kelvin (with required power supplies). D) Back :- Back is to be made of 4mm thick ACP with 0.5 mm thickness Aluminum Foil on both sides. E) Timer:- Auto operated using LandT/Havells/schneider timer of required capacity. F) ACP cladding is to be made of 4mm with 0.5 mm thickness Aluminum Foil on both sides.and ms frame used 37X37 SHS.Dully primer enamel paint. BRAND/MAKE- 247SIGN/ ASB Neon/ Vista d SUBENTRY

2 Providing and fixing RECEPTION SIGNAGE (SS 3D Letter) Providing and fixingl Signage made of SS 304 (brush finish) 1mm thick. Sheet for Logo and letters with raising (letter depth) of 50mm. Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated / hollow illuminated either back or front of the signage to be made of 4 mm thick acrylic. 3M/Avery/LG cast vinyl (90 micron and minimum 6 year product life) for desired colour with OSRAM make LED`s with 10000 kelvin and IP 67 grade powersupply along with SMPS fixed on the wall with necessary fixtures. a Reception signage

Providing and fixing 3 Signage to be made of stainless steel sheet of 1 mm thick 304 grade brush finish including engraving/etching of letters of required size filled with colour as desired by engineer,fixing with ss screws on walls.signages to be bilingual/trilingual language. a No smoking

Providing and fixing 3 Signage to be made of stainless steel sheet of 1 mm thick 304 grade brush finish including engraving/etching of letters of required size filled with colour as desired by engineer,fixing with ss screws on walls.signages to be bilingual/trilingual language. b No Littering

4 Providing and fixing AREA INDETIFICATION SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` a Room indentification

4 Providing and fixing AREA INDETIFICATION SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` b Department indentification

4 Providing and fixing AREA INDETIFICATION SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System. c Wash room ( Wall mounted )

4 Providing and fixing AREA INDETIFICATION SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System. d ROOM NO

4 Providing and fixing AREA INDETIFICATION SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System e LIFT LOBBY

4 Providing and fixing AREA INDETIFICATION SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` f Lift No

4 Providing and fixing AREA INDETIFICATION SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System g FLI Lift

4 Providing and fixing AREA INDETIFICATION SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System h Bed No

4 Providing and fixing AREA INDETIFICATION SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` i Drinking Water

4 Providing and fixing AREA INDETIFICATION SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System. j Authorised Person Only

5 Providing and fixing DIRECTORY SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. NOTE- Top header profile 120 mm, 15 contant profile 105mm. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` a Service Directory

5 Providing and fixing DIRECTORY SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. NOTE- Top header profile 120 mm, 15 contant profile 105mm. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` b Floor Directory(1200*1695 mm)

5 Providing and fixing DIRECTORY SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. NOTE- Top header profile 120 mm, 15 contant profile 105mm. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` c Floor Directory(1200*855 mm)

6 Providing and fixing INTERNAL WAYFINDING SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` a Wash room ( Wall Projected double side )

6 Providing and fixing INTERNAL WAYFINDING SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` a Wash room ( Wall Projected double side ) b WAY FINDING ( Celling Hung double side )

6 Providing and fixing INTERNAL WAYFINDING SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` c WAY FINDING ( Celling Hung single side )

6 Providing and fixing INTERNAL WAYFINDING SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System d Waiting Lobby

6 Providing and fixing INTERNAL WAYFINDING SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` e Nurse Station

6 Providing and fixing INTERNAL WAYFINDING SIGNS `Curved Signages made of extruded 6063 grade alloy confirming to B.S. 1474-1987 with copper/brass finish anodizing in 18-20 microns. Minimum 1.5mm wall thickness of extrusion with provisioning of housing print and 0.8- 1mm protective sheet in front side. Fixing arrangment made of anodised aluminium in Brass / Copper shade to be fixed at back side with Fastner . Alloy to be anodized to 18 to 20 microns . Side caps with 2mm aluminium anodised in same colour as main profile, side caps to be fixed to main plate using SS L key screws or same color coated screws as anodising. signages to be bilingual/trilingual language with pictograph as required. All signage is to be made in Bilingual language with suitable pictograph. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System.` f Reception

7 Providing and fixing PARKING WAYFINDER SIGN for Basement Double sided signage will be fabricated using 12 plus 12 mm thick twin ultra slim edge modular aluminium extruded profile of copper/brass shade anodising in 18-20 microns with approved ACP as base duly fixed over on both sides and retro reflective grade 4 vinyl duly digitally cut and pasted on ACP panels on both side. Signage will be hanged using SS cable/ SS chain with fastners. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System. a Directional (Double sided)

7 Providing and fixing PARKING WAYFINDER SIGN for Basement Double sided signage will be fabricated using 12 plus 12 mm thick twin ultra slim edge modular aluminium extruded profile of copper/brass shade anodising in 18-20 microns with approved ACP as base duly fixed over on both sides and retro reflective grade 4 vinyl duly digitally cut and pasted on ACP panels on both side. Signage will be hanged using SS cable/ SS chain with fastners. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System. Lobby indetification

8 Providing and fixing ENTRY SIGN for Basement with height limit Single Sided signage will be fabricated using 25 mm thick twin ultra slim edge modular aluminium extruded profile of copper/brass shade anodising in 18-20 microns with approved ACP as base duly fixed over on single sides and retro reflective grade 11 vinyl duly digitally cut and pasted on ACP panels on single side. Signage will be hanged using SS cable/ SS chain with fastners. BRAND / MAKE- 247SIGN/ ASB Neon/ VISTA System. a Single sided

Providing and fixing LED LIT DISPLAY PANELS ` EXTERNAL PROFILE and FRONT CLIP ON:- Made of alloy 6063 confirming to BS 1474-1987. Main load bearing frame profile to have minimum 2.5mm wall thickness made in Synchronization with front clip on profile having 1mm wall thckness. Main profile of depth 100 mm while 75 mm clip on front profile visible as front border. INTERNAL FRAME :- To be fixed using concealed MS frame work in shape of `T` section using 2 nos of SHS 40x40x2 mm and 50x25x2 mm duly welded and coated with primer and two coats of enamel paint. Front :- Front made of 200 Gsm flex with Ecosolvent Printing. Tied using eyelet @ 3`` interval. BACK : - Back is to be made of 4mm thick ACP with 0.45 mm thickness Aluminum Foil on both sides. Illumination :- Signage is to be illuminated with LED module of make OSRAM with 10000 kelvin (with required power supplies. BRAND / MAKE-247SIGN/COSIGN/VISTA SYSTEM`

Providing and fixing POSTER FRAME `Poster Frame made of alloy 6063 heavy copper/bronze anodizing, clip on arrangement for easy change of insert. Use 2mm clear acrylic as a protection layer in the front. BRAND / MAKE-247SIGN/ COSIGN/ VISTA SYSTEM`

1 Providing and fixing Building indentification Signage Providing and fixing Signage made of SS 304 (brush finish) 1mm thick.sheet for Logo and letters with raising (letter depth of 50mm). Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated / hollow illuminated either back or front of the signage to be made of 4 mm thick acrylic. 3M/Avery/LG cast vinyl (90 micron and 6 year minimum product life )for desired colour with OSRAM IP 67 grade approved LED`s along with 10000 kelvin SMPS fixed on the wallwith necessary fixtures. a ACADEMIC BLOCK

1 Providing and fixing Building indentification Signage Providing and fixing Signage made of SS 304 (brush finish) 1mm thick.sheet for Logo and letters with raising (letter depth of 50mm). Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated / hollow illuminated either back or front of the signage to be made of 4 mm thick acrylic. 3M/Avery/LG cast vinyl (90 micron and 6 year minimum product life )for desired colour with OSRAM IP 67 grade approved LED`s along with 10000 kelvin SMPS fixed on the wallwith necessary fixtures. SUBENTRY

1 Providing and fixing Building indentification Signage Providing and fixing Signage made of SS 304 (brush finish) 1mm thick.sheet for Logo and letters with raising (letter depth of 50mm). Including all fittings, accessories, fixtures, fabrication.The signage will be front illuminated / hollow illuminated either back or front of the signage to be made of 4 mm thick acrylic. 3M/Avery/LG cast vinyl (90 micron and 6 year minimum product life )for desired colour with OSRAM IP 67 grade approved LED`s along with 10000 kelvin SMPS fixed on the wallwith necessary fixtures. Examination Hall

1 Providing and fixing Building indentification Signage Signage to be made of stainless steel sheet of 1 mm thick 304 grade brush finish including engraving/etching of letters of required size filled with colour as desired by engineer,fixing with ss screws on walls. Signages to be bilingual/trilingual language. a Building name Indentification