Public Works Department Tender

[23.19.3]Painting of pole with brackets etc with 2 coats of enamelled paint or other approved paint. 3. Above 8 metres

[23.22.1.10]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.10. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 125 to 160 amp, 25 KA

[23.22.1.9]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.9. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 6 amp to 100 amp , 25 KA

[23.22.5.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole

[23.27.2]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 2. M.S. pedestal of size 750 mm wide , 900 mm high , 300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level , having a base of size 1050 mm x 600 mm x 250 mm below ground level . 0 0

[23.27.5]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 5. M.S. pedestal of size 1200 mm wide ,1500 mm high ,450 mm deep and bottom totally open , duly embeded in cement concrete block of size 1350 mm x 600 mm x 200 mm above ground level , having a base of size 1500 mm x 750 mm x 250 mm below ground level . 0 0

[24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required.

[24.1.13]EARTHING AND LIGHTENING ARRESTOR 13. Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as required.

[24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required.

[24.1.7]EARTHING AND LIGHTENING ARRESTOR 7. Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth electrode including soldering etc. as required.

[24.10.6]CIVIL ITEMS (USED COMMONLY IN ELECTRICAL WORKS) 6. Digging of pucca road in required width for laying of cable / pipe complete in all respect up to the entire satisfaction of Engineer-in charge

[24.2.7.2]LT CABLE 7.2. Supply and erection of suitable compression type brass cable glands for underground Cable :- 10 sqmm to 16 sqmm Cable 2 to 4 Core

[24.2.7.3]LT CABLE 7.3. Supply and erection of suitable compression type brass cable glands for underground Cable :- 25 sqmm to 50 sqmm Cable 2 to 4 Core

[24.2.8.4]LT CABLE 8.4. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 16 sqmm

[24.2.8.5]LT CABLE 8.5. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 25 sqmm

[24.2.8.6]LT CABLE 8.6. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 35 sqmm

[24.4.16]STREET LIGHT 16. Supply and erection of weather proof M.S. box of size 20 cm x 15 cm x 10 cm. covered with 3.00 mm thick M.S. sheet hinged cover, locking arrangement , housed in wall , including the cost of 1 no. 16 amp. 415 volts SP MCB and 2 nos. 63 amp. 415 volts neutral links fixed on hard wood board/10 mm Bakellite sheet in the M.S. box including painting and necessary connections .

[24.4.8.7]STREET LIGHT 8.7. Supply and erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with base plate including cost of nut and bolts , earthing studs, Integral Cable termination arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2 no 10 A SP MCB , end cover and all accessories as supplied by the manufacture including Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 9 Metre Long pole with top dia 100 mm and bottom 200 mm with base plate of size 350 x 350 x 20 mm.

[24.5.2.4]MISCELLANEOUS ITEMS 2.4. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 90/75 mm outer dia/inner dia

NS Items

Supply and Erection of single arm bracket made of 40mm dia G l pipe B class lSl 1.25mtr. Long with coller pipe (Gl) 75mm dia 60 cm Long top covered with ornamental cap duly welded painted 2 coats of aluminum paints on bracket and golden paint of ornamental cap including the cost of fixing the arm in pole including the cost of allied accessories required labour and petty material etc. complete in all respect up to the entire satisfaction of Engineer-in charge of the work.

Supply and Erection of double arm bracket made of 40mm dia G l pipe B class lSl 1.50mtr. Long with coller pipe (Gl) 75mm dia 60 cm Long top covered with ornamental cap duly welded painted 2 coats of aluminum paints on bracket and golden paint of ornamental cap including the cost of fixing the arm in pole including the cost of allied accessories required labour and petty material etc. complete in all respect up to the entire satisfaction of Engineer-in charge of the work.

Supply and Erection of G.I. double arm bracket having size of 48mm dia G l pipe B class lSl 1.50mtr. Long with coller pipe (Gl) 100mm dia 600 mm Long top covered duly welded painted 2 coats of aluminum paints on bracketincluding the cost of labour and petty material etc. complete in all respect up to the entire satisfaction of Engineer-in charge of the work.

Supply and erection of MS door cover size of 120x500 mm for existing 9 Mtr. octagonal pole including cost of nuts and bolts complete in all respect up to the entire satisfaction of Engineer of the work.

Supply and Erection of Horizontal Foundation for the street Light pole along with 1 mtr. piling including cost of all petty material and labour including CC work complete in all respect upto the entire satisfaction of Engineer in charge of the work.

Supply and Erection of Connection plate made of bakelite sheet for making connections for incoming and outgoing cable including all petty material and labour required to complete the job in all respect.

Dismentalling of chequered tiles flooring and precast chequered tiles including with repairing cost of dismentling of lean conc. CC with stone and other petty material with all labour with labour required to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work

Charges of boring 2.5 mtr. below the gound level treanchless horizental with laying of PLB pipe by HDD machine (for laying the cable) including all labour and material required to complete the job in al respect upto entire satisfaction of Engineer- in- charge.

Dismantaling and re - erection of mild steel railing and fencing guard of electric pole on the central verge including electricity charge welding and drilling equipment i.e. electrode and other consumable CC, Painting complete the job in all respect upto entire satisfaction of Engineer- in- charge.

Supply and Erection of Underground Copper unarmoured cable loose in existing pipe or trenches complete in all respect upto up to the entire satisfaction of Engineer-in-Charge of the work. 2.5 Sqmm 3 core (Un. Ard. Copper Cable) Make: - Polycab / RR / Havells

Supply and Erection of Underground Copper unarmoured cable loose in existing pipe or trenches complete in all respect upto up to the entire satisfaction of Engineer-in-Charge of the work. 2.5 Sqmm 5 core (Un. Ard. Copper Cable) Make: - Polycab / RR / Havells

Providing and Erection / Laying of PVC / XLPE insulated underground Aluminium Conductor underground Cable loose in existing Pipe or Trenches complete in all respect with necessary connection upto the entry satisfaction of Engineer - in - Charge of the work (Based on HSR Item No.24.13.24) 16 Sqmm. 4 Core (Arm.) Make: Havells / Polycab / RR.

Providing and Erection / Laying of PVC / XLPE insulated underground Aluminium Conductor underground Cable loose in existing Pipe or Trenches complete in all respect with necessary connection upto the entry satisfaction of Engineer - in - Charge of the work (Based on HSR Item No.24.13.32) 25 Sqmm. 4 Core (Arm.) Make: Havells / Polycab / RR.

Providing and Erection / Laying of PVC / XLPE insulated underground Aluminium Conductor underground Cable loose in existing Pipe or Trenches complete in all respect with necessary connection upto the entry satisfaction of Engineer - in - Charge of the work (Based on HSR Item No.24.13.40) 35 Sqmm. 4 Core (Arm.) Make: Havells / Polycab / RR.

Supply and Erection of LED Street Light Fitting 120 Watt with pressure dia cast aluminum Housing, Ingress IP 66 Protection, toughened Glass, fixture designed for operating voltage in the range of 140 - 270 Volt system efficacy of 120 lumens per watt, should have life of 50,000 burning hours, CRI (Colour Rendering Index) to be greater than 70 having LM 79 and LM 80 certificate, suitable surge protection, with 2 years warranty on site and complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work Make: - Havells / Wipro / Surya / Bajaj / Crompton

Supply and Erection of LED Flood Light Fitting 350 Watt with pressure dia cast aluminum Housing, Ingress IP 66 Protection, toughened Glass, fixture designed for operating voltage in the range of 140 - 270 Volt system efficacy of 120 lumens per watt, should have life of 50,000 burning hours, CRI (Colour Rendering Index) to be greater than 70 having LM 79 and LM 80 certificate, suitable surge protection, with 2 years warranty on site and complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work Make: - Havells / Wipro / Surya / Bajaj / Crompton

Supply and Erection of 40 Amp. 3 Pole / 230V 3 Phase Astronomical time switch of Indo Asian or its equivalent make of CandS / Schnieder / LandT / Havells along with contactor of required capacity of equivalent make movement controlled by preciosity quartz oscillation operation on main supply of continue to run on built in rechargeable nickel cadium call for 150 hours in the event of power failure including cost of all petty items complete in all respect upt the entire satisfaction of Engineer-in-Charge of the work.

Deduct - Buy back and Dismentaling of old 250W/350 W Sodium street light fittings including labour chArges for the same to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work

Deduct - Buy back of dismantled old octagonal/MS Steel tubular pole having size 9 mtr. And 11 Mtr. Long pole including cost of labour of the same to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work

Deduct - Buy back and dismentaled of existing street light bracket (Single arm / Double arm) including cost of labour from existing pole to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work

Deduct - Buy back of existing cable having size 16 Sqmm and 25 Sqmm including labour charge for removing from existing HDPE pipe/sand/CC including cost of repairing if any to complete the job in all respect upto the entire satisfaction of Engineer-in-Charge of the work