Public Works Department Tender
If you want to inquire about any e-tender the Haryana government has posted, Bidassist gives a one-stop solution i.e. being a registered bidder you will find every eprocurement Haryana tender on BidAssist.There is no need to enter all the details on the website of etender.up.nic.in as BidAssist helps you find the specific Haryana etender you're looking for. Read further to learn how to search and bid for etender Haryana.
Costs
EMD
₹ 2,680Document Cost
₹ 500Tender Fee
₹ 1,180
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_HRY_414676_1Tender No
PWD/P4/264Tender Authority
Public Works Department ViewPurchaser Address
-Website
http://https://haryanapwd.gov.in/
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
BOQ Items
Providing and fi xing glass strips,4 mm thick in terrazzo/ cement concrete floors.25mmwide (HSR 10.85.3)
100.87
-
-
Half brick masonry with common burnt clay non-modular bricks of class designation 7.5 in foundations and plinth in:-cement mortar 1:4 (1 cement: 4 coarse sand) (HSR 7.27.2)
10.93
-
-
Brick work with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes in :-Cement mortar 1:6 (1 cement: 6 coarse sand) (HSR 7.22.2)
3.08
-
-
Supply & fixing Windows frames (Chowkhats) including mullions consisting frame fabricated from sheet roll formed out of 1.2mm thick galvanized sheet as per IS:277 (Base steel as per IS 513) with zinc of 120 gm/sqm & Powder coated with pure Polyester powder up to 50 microns (as per approved colour), 3 Nos. 100mm butt - hinges 2mm thick, 6 Nos. 1.2mm thick CRCA electroplated stiffner, 6 Nos. M.S hold fast with split and tail welded to stiffner plate 200mm long, receiver for aldrop, weld less corner assembly with brackets & screws, M.S tie rod 50mm x 25mm to be fixed at bottom finished with powder coated total thickness of coating 0.6mm of approved shade, fixed in position including the cost of cement concrete for 1 :2:4 for fixing lugs complete in all respects as per drawing, design, specification & entire satisfaction of Engineer-in-charge.(HSR 13.21)
-
-
-
13.21.2:- Door Frame of size 125mm x 60mm with 37mm wide double rebate for 35mm door shutter
10.35
-
-
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes (HSR 13.30.1)
16.18
-
-
Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISi marked Stainless Steel butt hinges with necessary screw (HSR 12.37.1)
1.79
-
-
Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws, 35 mm thick shutters, with ISi marked M.S. pressed butt hinges bright finished of required size:- Kiln seasoned and chemically treated Hollockwood (HSR 12.32.1.1.2)
3.28
-
-
Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISi marked M.S. pressed butt hinges bright finished of required size with necessary screws.Kiln seasoned and chemically treated Hollock wood, 35 mm thick (HSR 12.10.2.1)
1.49
-
-
Providing and fixing ISi marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :-250x16 mm (HSR 12.65.2)
2
-
-
Providing and fixing ISi marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete:150x10 mm (HSR 12.66.3)
6
-
-
Providing and fixing ISi marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm (HSR 12.69.1)
12
-
-
Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 356 4, embossed on the body, door weight up to 35 kg and door width up to 7 00 mm), with necessary accessories and screws etc. complete.(HSR 12.88)
1
-
-
Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer:-M.S. tube (HSR 13.42.1)
392.08
-
-
Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete.(HSR 11.76)
13.11
-
-
Applying priming coat:With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood (HSR 11.68.2)
13.11
-
-
Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works (HSR 11.68.3)
86.15
-
-
Painting the wooden I metal surface with synthetic enamel paint of approved brand and manufacture to give an even shade:-Two or more coats on new work (HSR 11.82.1)
91.22
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%