Haryana Police Housing Corporation Tender

[13.30.2]Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. 2. Hot finished seamless type tubes [Through Rate]

[13.31]Providing and fixing mild steel round holding down bolts with nuts and washer plates complete. [Through Rate]

[22.181]Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. [Through Rate]

[22.85.3]Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 3. 25 mm nominal outer dia Pipes [Through Rate]

[22.85.4]Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 4. 32 mm nominal outer dia Pipes [Through Rate]

[23.20]Fixing of LED Tube light/ 2*2 ft square panel fitting directly on wall /ceiling or false ceiling including making connections etc as required [Through Rate]

[23.22.3.2]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 3.2. Supply and erection of sheet steel enclosures 1pole/2 pole/4 pole on wall/on existing pedestal complete as required. S.P.N. or DP enclosure suitable for DP MCB [Through Rate]

[23.22.5.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.3. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Double POLE [Through Rate]

[23.3.6.1]COPPER WIRING IN PVC CONDUIT (SURFACE/RECESS) 6.1. Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) [Through Rate]

[23.4.1.1]COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT (SURFACE/RECESS) 1.1. Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm thick PVC conduit pipe. Group A [Through Rate]

[23.7.6.2]PVC CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.2. Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 25 mm dia. [Through Rate]

[23.8.10.5]FITTING AND ACCESSORIES 10.5. Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 8 Modules [Through Rate]

[23.8.11.1]FITTING AND ACCESSORIES 11.1. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp 1 way switch [Through Rate]

[23.8.11.4]FITTING AND ACCESSORIES 11.4. Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. 5 amp Socket [Through Rate]

[24.14.13]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 13. 10 Sq mm 2 core (UnArm.) [Through Rate]

[28.6]`Providing and applying waterproofing treatment to sound, moisture free concrete surface using liquid applied single component pitch free polyurethane coating capable of bridging substrate cracks up to 2 mm. It shall be applied in two coats at coverage rate of 2kg/sqm to a achieve a minimum DFT of 1.3 mm. The membrane formed shall confirm to following minimum properties: 1) Elongation : )400% as per ASTM D 412 2) Tensile Strength : 2.5 N/mm2 as per ASTM D 412 3) Adhesion in-peel test : )50 N as per ASTM C- 836 4) Recovery from 350% elongation : 95% as per ASTM D 412 5) Water Vapour Transmission 2.3mm film: 0.6 g/m2/hr 6) Initial Hardness Shore A : min 60 as per ASTM D 2240 7) Root resistant : protection screed required System includes supply , application and termination of coating all complete as per the manufacturer`s methodology. Clean the RCC slab/screed surface and wall for treatment by removing dust, dirt and layers of concrete over the surface. etc. by mechanical tools and wire brushing. Pressure grouting at construction joints or honeycombs with non shrink cementations grout by mixing shrinkage compensating admixture per bag of cement as per manufacturer`s recommendations. Prepare a side gola of 50X50 mm at the junction using polymer modified mortar. Providing and applying liquid applied single component pitch free polyurethane coating in 2 coats at coverage rate of 2kg/sqm to a achieve a minimum DFT of 1.3 mm. (Fibre cloth/fleece/reinforcement should not be used in between two coats of PU as it has adverse effect on elongation property and also affects bonding with slab). Termination shall be done 300 mm above FFl by providing a groove cut of 30mm x 30mm and seal it with shrinkage compensated polymer modified mortar. Lay a 150 GSM geotextile layer to protect the coating from external damage on final coating before laying of screed concrete/final finish. It shall be applied as per manufactures specification. Rates are incl of surface preparation, grouting and chemical application only. (Rates for geotextile, protection plaster and final finishes such as screed or Brick bat filling for slope, china mosaic, tiles etc is not included in above item. It will be added as per EIC requirements).` [Through Rate]

[31.14.5]Rebarring work with 10ml inject able mortar epoxy adhesive (Hybrid Urethane Methacrylate adhesive) or chemical compound of make as approved by Engineer-in-Charge complete in all respect including drilling and cost of all materials 0 0 0 5. 20mm dia (hole size 24 mm dia & depth up to 240mm) 0 0 [Through Rate]

[5.11]Demolishing mud phaska in terracing and disposal of material within 50 metres lead. [Through Rate]

[5.14]Demolishing brick tile covering in terracing including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. [Through Rate]

[9.11.1]10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: 1. With common burnt clay non-modular brick tile of class designation 10 [Through Rate]

[9.17.1]Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : 1. In 75x75 mm deep chase [Through Rate]

[9.34.1]Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( plus 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 1. Ridges plain (500 - 600mm) [Through Rate]

[9.34.6]Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( plus 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : 6. Gutter (600 mm over all girth) [Through Rate]

[9.57.2]Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 2. 110 mm diameter [Through Rate]

[9.58.5.2]Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 5.2. Bend 87.5° 110 mm bend [Through Rate]

Supply of surface mounting LED batten fitting 1 x 18 /20 watt, (4 feet long), made of high grade polycarbonate body provided for efficient heat dissipation and Integrated electronic driver suitable for single phase A.C. 230 Volts, 50 Hz supply, complete in all respect.

Supply and erection of FRLS, PVC insulated unsheathed single core and PVC round sheathed multicore flexible copper cable for working voltage upto and including 1100 volts to is : 694/2010 – ISI marked complete in all respect. 1) 1.5sqmm

Supply and Erection of 50/60 watt LED Flood light suitable for operation on 230V ,50Hz complete the job in all respect . Make as per HPHC approved brands

Supply and Erection of CNC LASER CUT view cutter of length 160ft x 8ft approx made from 3mm thick HR sheet, Designing using CAD/CAM technique, Laser Cutting of design on the sheet. Surface treatment of laser cut sheet prior to Powder Coating with Pure polyster Green Colour powder and baking upto 200Deg.celcius, complete with packing, forwarding and installation at site....

Powder coated aluminum sliding Windows of size 1175x1175mm with 5mm Glass, wire mesh and Grill outside duly powder coated complete in all respect using Rollers, EPDM Gasket, Locking arrangements, handle, tower bolts of suitable size with powder coated of ISI marked complete in all respect......

Removing and refaxing of existing MS Step ladder complete in all respect to the entire satisfaction of Engineer in Charge.....

Providing and Fixing and jointing of CPVC Gate Valve on CPVC pipelines complete in all respect to the entire satisfaction of Engineer in Charge........

Expansion Joint Treatment with 65mm width :-Cleaning of surface and make it for Dust Free. Any repair for edges of expansion joint will be done with Sand and cement. Providing and fixing of Thermo Plastic Elastomer Tape(TPE Tape) width 150 mm and thickness 1 mm designed for water tightness of expansion joint. The TPE Tape Should is applied with help of suitable epoxy Adhesive. Place the tape over the adhesive in such a way that 10mm adhesive remained exposed .Press the tape slightly to ensure good adhesion. Then Apply 2nd coat of Epoxy adhesive on the tape. The epoxy adhesive consumption will be 1.5 kg per RMT The TPE Tape should have following properties : a. Elongation at Break )400% b. Tear strength )25Kn/m c. Adhesion By epoxy )52 N d. Tensile Strength )5 e. Chemical Para meter : Resistance to Water, Sea Water, Waste Water,UV Radiation, Microorganisms, Acids, Alkalis f. pH resistance: pH = 2 to 10 (Below 30degree temp.), 25to 10 (Below 40degree temp.) After fixing of TPE Tape, Apply Aluminum expansion joint plate on the ground level. The Aluminum plate will be width of 150 mm. The plate should be one side fixed with help of screws and other side loosely laid. Filling of PU sealant on edge of Aluminum Plate..................

Providing and fixing of 50mm thick PUF insulated Wall Panel with 0.50mm thick PPGI sheet (Make JSW) (Ral-9002) both sides, with FR Grade PUF Density 44Kg/m3 plus 10% in metallic tongue and Groove joint system, cut to size, with no loading of wastage with additional 90° bends in Male and Female groove to have proper sealing, Strength and Air Tight joints Panel to Panel, CFC free and Ozone friendly, complete with top bottom U Channel, Inner and Outer flashing complete with filling of joints with Silicone sealant along with taping to protect from water seepage and complete arrangement of providing and fixing of required size Hilti make fastener as per design and drawing complete in all respect to the entire satisfaction of engineer in-charge of the work.............

Providing and fixing of Puf Insulated Doors with 40mm thick leaf and powder coated chowkhat complete with powder coated aluminum accessories like Hinge, Tower Bolts, Handles, Areal Drop, Door stopper, Door Closer of ISI marked complete in all respect.....

-Providing and Fixing and jointing CPVC union couplings in CPVC pipelines complete in all respect to the entire satisfaction of Engineer in Charge..............

Providing and fixing of 65/35mm puf insulated Roof panel with 0.50mm thick corrugated profile sheet from outside and light grooved 0.50mm thick PPGI inside with FR Grade PUF Density 44 Kg/m3 plus 10% with proper overlapping and projections on all sides complete with all accessories like Fleshing and Roof edge covering channels complete with filling of joints with Silicone sealant along with taping to protect from water seepage complete in all respect.............

Providing and fixing artificial grass on porch portion complete in all respect