Military Engineer Services Tender

Cleaning of dust Removal of all loose existing bituminous material manually and with heat torch gun to get smooth plain finished surface including removing of vegetation/plantation with no loose material on surface. Repair all joints and cracks with Highly elastic Bituminous cold applied putty of Tarplasic having penetration after setting upto 8mm. Levelling of surface to give proper slope will be done as per site requirements with Shalipatch or equivalent make of approved by GE cold applied, Bituminous Mortar & Cold Emulsion cum waterproofing Liquid of Shalikote-T-10 or equivalent make of approved by GE, Created SSD condition on surface with water. Prime the surface with Tarfelt LM or equivalent make of approved by GE mixed with portable water in the ration of 1 :1 and apply @400gm per Sqm (As per Surface Conditions). . Apply first coat of Tarfelt LM or equivalent make of approved by GE having elongation 200% conforming to ASTM-C-412 & having crack bridging of 8mm confirming to ASTM-C-836 with tensile strength after 7 days 0.50 mm conforming to ASTM-C-412 with no diluation of water on primed surface while the surface is still tacky with consumption of 700gm per Sqm. . Lay Geotex of 45 GSM/ Fibre mesh simultaneously and paste it properly with overlap of 50mm. . Allow the first coat to dry for 10 to 12 Hrs. . Apply 2nd coat on cured first coat with consumption @ 700gm per Sqm in opposite direction of first coat by Brush or Roller. Allow it to dry for 10-12 hrs after apply 3rd coat with consumption @ 700gm per Sqm.Ensure final curing time of 36 hrs before allowing/ carrying out any further work. Conduct ponding test after min 7 day applying two coats of U V Resistand Elastomeric Exterior Axcrylic Weather resistant water proof coating of Shalicryl-215 or equivalent make of approved by GE having elongation of 300% after curing of 14 days confirming to ASTM D- 6083-- for U V Protection of Bituminous Elastomeric Acrylic Emulsified Liquid Membranc of Tarfelt LM or equivalent make of approved by GE to give long life and prevent its deterioration from sunlight. Note:- (i) Application of water proofing treatment will be done by Authorised Applicator only. (ii) Water proofing treatment shall bear a performance guarantee of 10 years from the date of completion. The contractor has to submit the said guarantee in Rs 100 non-judicial stamp paper to the Accepting Officer (iv) An amount @ 5% of the cost of water proofing treatment shall be retained from the final bill till completion of above guarantee period. However, The contractor may submit FDR of equal amount in favour of the Accepting Officer for this purpose and the amount due shall be released in due payment.

M&L for chipping and removing all loose / spalling out concrete including loose plaster from old surfaces of RCC Surfaces, and providing one layer of guniting, cleaning the exposed steel by sand blasting and providing and welding new reinforcement (if required and directed) to old steel and applying two coats of anti-corrosive zinc chromate paint (both on old and new steel), applying one coat of epoxy based adhesive over exposed surfaces to receive guniting, including supplying and fixing stainless steel wire mesh of size 1.40mm nominal dia average width of aperture 12mm and binding with 22gauge binding wire with reinforcements or with stainless steel staples and pressure guniting the surface with CM 1:3 with average thickness 35mm with equipment as per IS: 6433-1972 and IS:9012-1978 and then rendering the surface in 10mm thick CM 1:4, finishing the surface even and smooth without using extra cement, including all necessary scaffolding and staging and rubbishing off the premises complete all as specified and as directed

Dismantling of floor hearth or wall tiling including cement mortar bedding but not backing and removing serviceable tiles to store yard and rubbish off the premises complete all as specified and directed