Military Engineer Services Tender

... More
The MES has issued a formal invitation for competitive bids for the Military Engineer Services project, for Cwe/chm-90/2026-27 Repair To Certain Internal Roads, Kerb Stone And Road Furniture In Otm And Md Accn Under Ge Chandimandir in Panchkula, Haryana, with an estimated contract value of Rs. 1,04,50,000. The bid opening date for this tender is 07-11-2026 and the last date for bid submission is 05-12-2026. Interested bidders for Military Engineer Services tender can download the important documents here to check the scope of work, eligibility criteria and technical requirements.

Military Engineer Services - MES Tender - Haryana Tender

Opening Date7 Nov 2026
Closing Date5 Dec 2026
Tender Amount₹ 1,04,50,000 
Notes
Download

Costs

Description

Cwe/chm-90/2026-27 Repair To Certain Internal Roads, Kerb Stone And Road Furniture In Otm And Md Accn Under Ge Chandimandir

Contact

Unlock the Tender details

GEM & Bid Advisory Services

Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost

BOQ Items

... More
DO_NOT_SHOW

-

-

-

Unlock the Tender details
... More
Contd.. including manual operation as and when required for proper grade, including level and camber through rolling with power roller 8 to 12 tonnes smooth wheeled, vibratory and tendom roller with necessary hand packing and pinning to give an even surface including running expense of all plants and machineries, inclusive of proper traffic control during laying to the satisfaction of Engineer-in-charge, required quality control tests at required interval etc complete in all respects complete all as specified and as directed by Engineer-in-Charge. Notes: (i) Job Mix formula as per clause No. 505.3.3 of MORT&H specification for road and bridge work (Fifth Revision) for bituminous concrete shall be got designed from NIT/CTL/Govt Engg Collage and shall be got approved from GE in writing well before commencement of work without any financial effect to the department. Also the bitumen content shall not be less than 5.4 % by weight of total mix as per clause 507.2.5 of MoRT&H specifications (Fifth Revision).

-

-

-

... More
(ii) The cost of materials, transportation, Job mix formula from lab and testing charges for various tests as required are included in the unit rate quoted by the contractor. (iii) Cost of Filler i.e. rock dust, hydrated lime or cement is deemed to be included in unit rate. (iv) If qty of binder contents is less than the qty as specified in respective items of BOQ, it shall be adjusted at supply only rates of paving bitumen @ Rs. 65.00 Per KG and if qty of binder contents is more than the qty as specified in respective items of BOQ no adjustment shall be made. (v) After spreading of mix as per clause 507.4.7 of MoRT&H specification entire surface during the operation shall be rolled with road roller 8-10 tonnes (smooth wheeled) followed with vibratory road roller of 8-10 tonnes static weight, followed by finish rolling with 6 to 8 tonnes smooth wheeled tandem roller as per clause No. 507.4.8 of MoRT&H specifications (Fifth Revision) and the cost of the same shall be deemed to be included in the quoted rate.

-

-

-

... More
M&L for Scarifying or picking gravelled, macadam or bituminous macadam surfaces in area not exceeding 400 sqm and not exceeding 50 mm deep complete all as specified and as directed by Engineer-in-charge.

27

10

-

... More
M&L for Applying evenly a prime coat of Cationic Bitumen Emulsion SS1 confirming to IS: 8887 at a rate of application of 0.7 - 1 kg/sqm on surface of WMM/ WBM as specified in Table 500-3 of MoRT&H specification for Road and Bridge works 2013, using mechanical sprayer complete all as specifed and directed by Engineer-in-Charge.

27

11

-

... More
M&L for Providing, laying & Compaction of bituminious, macadam (BM) compacted thickness not exceeding 75 mm thick conforming to clause 504 of MoRT&H specification for Road and Bridges works (Fifth Revision) using mechanically crushed stone aggregates and granual material etc of grading II as per Table 500-7 of MoRT&H specification for Road and Bridges work (Fifth revision) Premixed with bituminious binder bitumen grade VG-30 @3.4% (percent by weight of total mix) prepared in batch type Hot Mix Plant transported to site by tippers, laid over a previously prepared surface with paver finisher equipped with electronic sensor to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to achieve the desired compaction and density complete all as specified and directed by Engineer-in-charge.

20

100

-

... More
Notes : (i) Mix Design for Bituminous macadam shall be got designed from NIT/ CTL/ Govt Engg College and shall be got approved from GE in writing well before commencement of work without any financial effect to the department. Also the bitumen content shall not be less than 3.4% by weight of total mix as per clause 504.2.4 of MoRT&H specifications (Fifth Revision). (ii) If qty of binder contents is less than the qty as specified in respective items of BOQ, it shall be adjusted at supply only rates of paving bitumen @ Rs. 65.00 Per KG and if qty of binder contents is more than the qty as specified in respective items of BOQ no adjustment shall be made.

-

-

-

... More
Material and Labour for Repair to pot holes of any depth, not exceeding 1.00 sqm each including sweeping free from dust and mud or water, scouring sunken surfaces in roads, paths etc., cutting around edges to at least 25 mm in depth and making good by filling in screened & graded road metal, watering and well ramming (including supply of road metal) complete all as specified and as directed by Engineer-in-charge.

5

100

-

... More
M&L for preparing bituminous surfaces of road and marking 2.50 mm thick centre lines, stop lines, dashes, arrows etc. and the like on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturer's instructions complete all as specified and directed by Engineer-in-Charge.

135

11

-

... More
Supply and fixing in repair solar cat eye/ solar stud, aluminum alloy shell (100% water proofing design) of size 125 mm x 125 mm x 25 mm (shank 65 mm) of high efficiency Mono crystaline solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/1600MA) consisting of super bright LED with 10,000 to 18,000 mcd with high visibility of distance upto 1000 metres and fixing with special epoxy bond all as per manufacturer's instructions etc., complete all as specified and as directed by Engineer-in-charge.

350

100

-

... More
Supply and fixing in repair cat eye, solar reflective type, of metal body alloy of size 100 mm x 100 mm x 20 mm with PAMA striplens reflector of model No. DA 972.0 fixed with and including MS stud of suitable size and fixing with special epoxy bond as per manufacturer's instructions complete all as specified and as directed by Engineer-in-charge.

500

100

-

... More
Supply and fixing in repair metal tubular delineator made out of ABS round body, fitted with 4 Nos 100 mm dia highly reflective reflectors made out of PMMA and mounted on 45/ 50 mm dia mild steel pipe duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 type B-1 of block size 150 x 150 x 300 mm complete all as specified and as directed by Engineer-in-Charge.

50

11

-

... More
Supply and fixing in repair solar delineator made out of high quality of polycarbonate and ABS material with three high intensity retro reflective bands of 25 mm width in red color assembled with solar panel 2.4 volt/ 205 mA or 3 volt/ 150 mA having charging capacity at very low sunlight with 1.2 volt, 1300 mAh or 3.6 volt, 1000 mAh Ni-MH rechargeable battery with six super bright LEDs providing 360 degrees visibility with powder coated steel pipe of 50 mm dia and approximate length 1150 mm and anti-theft wire mesh covered and including embedding in PCC Block (size 150 x 150 x 300 mm) 1:2:4 type B-1 including necessary excavation work in post holes complete all as specified and as directed by Engineer-in-Charge.

50

100

-

... More
S&F convex mirror minimum 100 cm in dia, outdoor type, body material- Polycarbonate, acrylic mirror, thickness not less than 3 mm having wide field of vision, exterior weather proof bright reflection, anti glare for traffic security purpose mounted on 2 metre long SS pipe Gde 304 fixed with nut bolt and adjustable brackets/ clamps system including necessary excavation including embedding in PCC 1:2:4 type B-1 (using 20 mm graded stone aggregates) with block size 600 x 600 x 600 mm complete all as specified and as directed by Engineer-in-Charge.

11

10

-

... More
Supply and fixing modular rumble strip block of size 500 × 100 × 15 mm made of UV-stabilized PU material, resistant to fading and weathering, fixed to road surface with approved epoxy bonding compound and 05 Nos. 10 mm dia anchor fasteners per block, including drilling, anchoring, grouting and all accessories complete all as specified and as directed by Engineer-in-Charge.

10

11

-

... More
Demolition of plain cement concrete in ground floor and paving not exceeding 15 cm thickness below or above ground level and removal of debris upto a distance of 50 metres from starting point and depositing where directed complete all as specified and as directed by Engineer-in-Charge.

135

10

-

... More
Demolition of stone slabs and tiles of any description or thickness in floors, laid and pointed in any mortar including removing the rubbish outside of MoD land complete all as specified and as directed by Engineer-in-charge.

200

11

-

... More
M&L for 75 mm thick PCC 1:4:8, type D-2 (using 40 mm graded stone aggregates) as in sub base, path, floor, hard standing, finished even and rough without using extra cement complete all as specified and as directed by Engineer-in-charge.

1800

10

-

... More
M&L for Providing and laying 80 mm thick with glossy finish on top factory made chamfered edge cement concrete paver block with grey cement and pigment of M-30 grade with colour, design & pattern (approved by GE) as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and as directed by Engineer-in-charge.

1000

11

-

... More
M&L for Providing and laying 60 mm thick with glossy finish on top factory made chamfered edge cement concrete paver block with grey cement and pigment of M-35 grade with colour, design & pattern (approved by GE) as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and as directed by Engineer-in-charge.

800

10

-

... More
M&L for Providing and laying 40 mm thick with glossy finish on top factory made chamfered edge cement concrete paver block with grey cement and pigment of M-35 grade with colour, design & pattern (approved by GE) as in footparth, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and as directed by Engineer-in-charge.

200

11

-

... More
M&L for Providing cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregates) as in roof kerbs or mud stops, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, gola, kneelers, apex stones, bed plates, kerbs including weathering, slightly rounded or chamfered angles and throating on edges complete all as specified and as directed by Engineer-in-Charge.

10

10

-

... More
M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3, including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and as directed by Engineer-in-charge.

10

100

-

... More
M&L for preparation of new concrete surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of primer on kerb stone in desired colour pattern complete all as specified and as directed by Engineer-in-Charge.

200

10

-



Evaluation Notes How It Works ?

Related Tenders

Disclaimer: BidAssist has made every reasonable effort to ensure that the information is accurate and authentic however it cannot be held liable for any third-party claims or losses of any damages. BidAssist makes no warranty, expressed or implied, as to the results obtained from the use of the information. If you think you may have noticed any error or omission, please let us know by contacting contact@bidassist.com.