Maharshi Dayanand University Tender

Damp proof course 40mm thick of cement concrete 1:2:4 using stone aggregate 20mm nominal size with 2 coat of bitumen 20/30 penetration at 1.65 Kg per sqm. Laid hot and sanded

First class brick work laid in cement sand mortar 1:5 in first storey upto 4 meters above plinth level.

12 mm thick cement plaster 1 : 4

15 mm thick cement plaster 1:4 on the rough side of single or helf brick wall.

Pressed steel sheet frames (chowkats), consisting of 2mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hings, confirming to PWD specifications, including bolts for fixing stops, locknutch, provision for receiving tower bolts and finished with one coat of ready mixed paint red lead non setting primer of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs complete. (a) Door and window frame of size 127mmx50mm with 40mm wide single rebate

Factory manufactured solid flush door shutter with block board core as per IS No. 1659-1969 bonded with water proof type phenol formal dehyde synthetic resi, hot pressed conforming to IS 2202 part-I and Iind fixed in position , including iron hinges, screws, chocks/ cleats and stops, etc. ( excluding the cost of any fittings other than specified above, but including labour for fixing the same in position (iii) 35mm thick.

Factory manufactures panelled door or glazed window, shutters of commercial hard wood, such as hillock, champ, chikrassy and chaplash etc. (non coniferous timber other teak, conforming to IS specification No. 1003, kiln seasoned) with 100mm wide vertical styles 150mm wide lock rail 200mm wide bottom rail and 100mm wide other rails, with panels of 15 mm thick , tongued and grooved of commercial hard wood and including cost of iron hings, screws, chocks/cleats, stops, nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position) 30mm thick

Factory manufactured wire gauge door and window shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash etc. (non coniferous timber other teak, conforming to IS specification No. 1003, kiln seasoned) with 100mm wide vertical styles 150mm wide lock rail 200mm wide bottom rail and wire gauge of 140G or 120G designation including cost of iron hings, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified cost of any fittings, other than specified above, but including labour for fixing the same in position)- 30mm thick

35 mm thick

Cost of aluminum fittings complete for doors and windows, such as tower bolts, handles, etc. and screws for these fittings (exluding sliding bolt) for double leaf shutter

Cold twisted deformed (ribbed/tor steel) bars for RCC where not included in the complete rate of RCC including bending , binding and placing in position complete

Wrought iron and mild steel (using angle,flats,square bars,tee,and channels) ladders grills,gratting frames, windowguards, iron doorsopenable or fixed stair case or parapet or any other type of railing, gates and tress guards etc including cost of screws and welding rods or bolds and nuts complete fixed in position

Cement concrete 1:1 1/2:3 with stone aggregate 20mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal excluding steel reinforcement , but including centering and shuttering, laid in position, complete in all respect (a) Extra over Item Nos. 10.79 to 10.94, if 1:1 1/2:3 mix is used, instead of 1:2:4

Terracing consisting of tiles 22.86 cmx 11.43 cm x 3.81 cm. laid over 87.50 mm mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 Kg. per sqm. Top of RCC slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc

First class brick work laid in cement sand mortar 1:4 in first storey upto 4 metres abover plinth level.

Conglomerate floor 50mm thick cement concrete topping 1:2:4.

Cement concrete 1:2:4 with stone aggregate 20 mm nomical size in pavements, roads, taxitracks and runways, laid to required slope and camber, including consolidation, finishing and tamping complete.

Providing and fixing aluminum work for doors, and windows ventilators and partition with extruded built up standard tubular / section /appropriate Z sections and other section of approved make conferring to IS, 733 and IS, 1285 fixed with rawlplugs and screws or with fixing clips or with expansion hold fasteners including filling up gaps at junction it top, bottom, and sides with required neoprene felt etc. aluminum screws shall be smooth, rust free straight mitred and jointed mechanically wherever required including cleat angle. Aluminum snap beading for glazing/ cancelling C.P brass / stainless steel screws, all complete. Fixed Portion: ( Anodised aluminum transparent or dyed to required shade according to IS:1868, minimum anodic coating of grade AC15)

Providing and Fixing aluminium work for Doors, Windows Ventilators and Partitions with extruded built up standard Tubular Sections/Appropriate Z Sections and Other Sections of approved make conforming to I.S 733 and I.S 1285 fixed with Rawlplugs and Screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at Junctions, At Top Bottom and Sides with required neoprene felt etc aluminium sections shall be smooth, rust free straight miltred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for Glazing/Panelling C.P Brass/Stainless Stell Screws etc complete ( Make : Jindal / Hindalco) Shutters of Doors Windows and Ventilators including providing and fixing Hinges/Pivots and Making provision for fixing of fittings wherever required including the cost of PVC/Neoprene gasket required including aluminium fitting.

Providing and fixing glazing in aluminum door, windows, ventilator shutter and partitions etc. with PVC /neoprene gasket etc complete (cost of aluminum snap beading shall be paid in basic items) With float glass panes of 5.0mm thickness.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS: 6315 marked for doors including cost of cutting floors as required embedding in floors and cover/ plates with brass pivot and single piece M.S. sheet outer box. with stainless steel cover plate.

Cement pointing 1:2 flush on flat brick flooring

Cement concrete 1:2:4 gola 10x10cm quadrant along junction of roof with parapet wall finished smooth , where specified

Providing and fixi ng Rain water pipe 6 kg Pressure of ISI make in cement mortar during masonry work. (a) 100 mm dia PVC pipe 6kg Pressure.

Providing and fixing PVC bend ISI mark 100 mm dia PVC Bend

Providing and applying two coats white cement based putty over plastered surface and grinding the surface smoothwith sand paper to fet an even and smooth finish including cost and carrigr of all material, labour charges, scaffolding, sundries etc. complete(J.K./Brila make)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on now work.

Providing two coats of exterior acrylic emulsion paint (1st Quality) complete in all respect as approved by Engineer-in- charge Make:- Top quality of Asian/Nerolac

Applying priming coat with ready mixed exterior paint in all shades on newly plasterd or concrete exterior surface.

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping, etc. Painting two coats excluding priming coat with synthetic enamel paint in all shade on new wood work or metallicor plastered or concrete surface to give and even shade

Cement concrete 1:2:4 with stone aggregate 20mm nominal size for reinforced concrete work in shelves excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects.

11.43 cm. thick brick wall laid in cement sand mortar 1:4 in super structure.

Supply and fixing Tibba sand complete as per entire satisfaction of the Engineer-in-charge

Providing and fixing aluminium sheet 8'' wide and 2mm thick (14 guage) on expension joint complete in all respect up to the entire satisfaction of Engineer-in-charge.