Lala Lajpat Rai University Of Veterinary And Animal Sciences Tender

HSR 12.158 Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge HSR 12.158.2 Pre-laminated particle board with decorative lamination on both sides

HSR 12.159 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): HSR 12.159.2 With float glass panes of 5 mm thickness (weight not less than sqm 12.50 kg/sqm)

HSR 12.16 Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. HSR 12.160.1 With stainless steel cover plate minimum 1.25 mm thickness

HSR 12.164 Providing and fixing Brass 100mm mortice latch and lock with 6 levers each without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

HSR 12.167 Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge HSR 12.167.3 Polyester powder coated minimum thickness 50 micron aluminium Handles

HSR 13.1 Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with

HSR 3.1.18 Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical cum 226transport including loading, transporting, unloading to approved municipal dumping ground for lead up to 10 kmfor all lifts, complete as per directions of Engineer-in-charge

HSR 5.45 Dismantling old plaster or skirting raking out joints and cleaning sqm the surface for plaster including disposal of rubbish to thedumping ground within 50 metres lead.

HSR 5.25 Demolishing R.C.C. work manually/ by mechanical means cum including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - incharge

HSR 5.42 Dismantling cement conglomerate / terrazzo floors 25 mm to 50 sqm mm manually/ by mechanical means and disposal of materialwithin standard lead as per direction of Engineer- in-charge.

HSR 30.21 Removing white or colour wash by scrapping and sand papering sqmand preparing the surface smooth including necessary repairs toscratches etc. complete

HSR 9.46 Providing and fixing false ceiling at all height including providing and fixing offrame work made of special sections, power pressed from M.S. sheets andgalvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS:277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick withflanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixedto the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm diabolts, other flange of cleat fixed to the angle hangers of 25x1 Ox0.50 mm ofrequired length with nuts & bolts of required size and other end of anglehanger fixed with intermediate G.I. channels 45x15x0.9 mm running at thespacing of 1200 mm centre to centre, to which the ceiling section 0.5 mmthick bottom wedge of 80 mm with tapered flanges of 26 mm each having lipsof 10.5 mm, at 450 mm centre to centre, shall be fixed in a directionperpendicular to G.I. intermediate channel with connecting clips made out of2.64 mm dia x 230 mm long G.I. wire at every junction, including fixingperimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawlplugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval,including fixing of gypsum board to ceiling section and perimeter channel withthe help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, includingjointing and finishing to a flush finish of tapered and square edges of theboard with recommended jointing compound , jointing tapes , finishing withjointing compound in 3 layers covering up to 150 mm on both sides of jointand two coats of primer suitable for board, all as per manufacturer'sspecification and also including the cost of making openings for light fittings,grills, diffusers, cut outs made with frame of perimeter channels suitably fixed,all complete as per drawings, specification and direction of the Engineer inCharae but excludina the cost of oaintina with

HSR 10.71 Providing and laying Vitrified tiles in floor with different sizes (thickness to bespecified by the manufacturer), with water absorption less than 0.06% andconforming to IS:15622, of approved brand & manufacturer, in all colours andshade, laid with cement based high polymer modified quick set tile adhesive(water based) conforming to IS: 15477, in average 6 mm thickness, includinggrouting of joints (Payment for grouting of joints to be made separately).

HSR 10.69 Providing and laying Vitrified tiles in different sizes (thickness to be specifiedby the manufacturer), with water absorption less than 0.08% and conformingto IS: 15622, of approved brand & manufacturer, in all colours and shade, inskirting, riser of steps, laid with cement based high polymer modified quick

HSR 11.5 12 mm cement plaster of mix

HSR 30.28 Painting with synthetic enamel paint of approved brand andmanufacture of required colour to give an even shade

HSR 11.58 Providing and applying two coats white cement based putty of approved sqm 26 10 36brand and manufacturer, over plastered surface and grinding the surfacesmooth with sand paper to get en even and smooth finish including cost andcarriage of all material , labour charges, scaffolding, sundries etc. complete

HSR 11.67.1 Applying one coat of water thinnable cement primer of approved brand andmanufacture on wall surface:11.67.1 Water thinnable cement primer

HSR 11.71.1 Wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade :11. 71.1 Two or more coats on new work

HSR 12.99 Providing and fixing aluminium tower bolts, ISi marked, anodised (anodiccoating not less than grade AC 10 as per IS : 1868 ) transparent or dyed torequired colour or shade, with necessary screws etc. complete

HSR 12.173 Providing and fixing bright finished 100 mm mortice lock with 6 levers withoutpair of handles of approved quality for aluminium door, with necessary screwsetc complete as per direction of Engineer- in-charge.

HSR 12.86 Providing and fi xing bright finished brass hanging type floor door stopper with each 1 100 1 02necessary screws, etc. complete

HSR 12.88 Providing and fixing aluminium die cast body tubular type universal hydraulic each 47 885 93 2door closer (having brand logo with ISi, IS : 356 4, embossed on the body,door weight up to 35 kg and door width up to 7 00 mm), with necessaryaccessories and screws etc. complete

HSR 12.157 Providing and fixing aluminium work for doors, windows, ventilators andpartitions with extruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessaryfilling up the gaps at junctions, i.e. at top, bottom and sides with requiredEPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rustfree, straight, mitred and jointed mechanically wherever required includingcleat angle, Aluminium snap beading for glazing / panelling, C.P. brass /stainless steel screws, all complete as per architectural drawings and thedirections of Engineer-in-charge. (Glazing, panelling and dash fasteners tobe paid for separately) HSR 12.157.1.3 Polyester powder coated aluminium (minimum kgthickness of polyester powder coating 50 micron

HSR 12.157.2 For shutters of doors, windows & ventilators including providingand fixing hinges/ pivots and making provision for fixing of fittingswherever required including the cost of EPDM rubber / neoprenegasket required (Fittings shall be paid for separately) HSR 12.157.2.3 Polyester powder coated aluminium (minimum kgthickness of polyester powder coating 50 micron)

HSR 12.158 Providing and fixing 12 mm thick prelaminated particle board flat pressedthree layer or graded wood particle board conforming to IS: 12823 Grade IType II, in panelling fixed in aluminium doors, windows shutters and partitionframes with C.P. brass / stainless steel screws etc. complete as perarchitectural drawings and directions of engineer-in-charge HSR 12.158.2 Pre-laminated particle board with decorative lamination on both sides

HSR 12.159 Providing and fixing glazing in aluminium door, window, ventilator shuttersand partitions etc. with EPDM rubber / neoprene gasket etc. complete as perthe architectural drawings and the directions of engineer-in-charge . (Cost ofaluminium snap beading shall be paid in basic item): HSR 12.159.2 With float glass panes of 5 mm thickness (weight not less than sqm12.50 kg/sqm)

HSR 12.160 Providing and fixing double action hydraulic floor spring of approved brandand manufacture conforming to IS : 6315, having brand logo embossed onthe body / plate with double spring mechanism and door weight up to 125 kg,for doors, including cost of cutting floors, embedding in floors as required andmaking good the same matching to the existing floor finishing and coverplates with brass pivot and single piece M.S. sheet outer box with slide plateetc. complete as per the direction of Engineer-in-charge. HSR 12.160.1 With stainless steel cover plate minimum 1.25 mm thickness

HSR 12.102.2 Providing and fixing aluminium handles, ISi marked, anodised (anodic coatingnot less than grade AC 1 O as per IS : 1868) transparent or dyed to requiredcolour or shade, with necessary screws etc. complete

HSR 8.27.2 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc.,including machine polishing to edge to give high gloss finish etc. complete asper design approved by Engineer-in-Charge.

HSR 8.26 Providing and fixing 18 mm thick gang saw cut, mirror polished, premouldedand prepolished, machine cut for kitchen platfonns, vanity counters, windowsills, facias and similar locations of required size, approved shade, colour andtexture laid over 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarsesand), joints treated with white cement, mixed with matching pigment, epoxytouch ups, including rubbing, curing, moulding and polishing to edges to givehigh gloss finish etc. complete at all levels

HSR 5.30.1 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead

HSR 7.22.2 Brick work with common burnt clay non-modular bricks of classdesignation 7.5 in foundation and plinth in:

HSR 5.46 Dismantling wooden boardings in lining of walls and partitions,excluding supporting members but including stacking within 50metres lead5.46.1 Up to 10 mm thick

HSR 6.16 Reinforced cement concrete work in beams, suspended floors, cumroofs having slope up to 15° landings, balconies, shelves,chajjas, lintels, bands, plain window sills, staircases and spiralstair cases above plinth level up to floor four level, excluding thecost of centering, shuttering, finishing and reinforcement with1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stoneaggregate 20 mm nominal size

HSR 7.28 Half brick masonry with common burnt clay non-modular bricksof class designation 7 .5 in superstructure above plinth level up tofloor IV level. HSR 7.28.2 Cement mortar 1 :4 ( 1 cement :4 coarse sand

HSR 20.71.1 Supply,erection,testing of ceiling fans IS marked (as per IS code 374) with suitable GI pipe complete in all respects complete as per directions of Engineer-in-charge. 48" (1200 mm)

HSR 20.72 Supply,erection,testing of exhaust fan (as per IS code 374) having a capacity of 45 cubic metre per minute complete with GI sheet ducting in structure confirming to latest IS specification complete in all respect to satisfaction of Engineer-in-charge.

HSR 23.4.1 Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper HSR 23.4.1.1 Group A

HSR 24.4.4 Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box ,modular face plate etc complete as required HSR 24.4.4.1 Group A

HSR 23.4.5 Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI Box , modular face plate etc complete as required HSR 23.4.5.1 Group A

HSR 23.5.6 Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. HSR 23.5.6.1 1 run of Size 1.50 Sqmm(1/1.40mm)

HSR 23.5.6.3 1 run of Size 4 Sqmm(1/2.24mm)

HSR 23.7.6 Supply and erection of PVC conduit pipe ISI marked (Medium) recessed in wall / ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. (TELEPHONE) HSR 23.7.6.2 PVC pipe of 25mm dia

HSR 23.22 MCCB ,DISTRIBUTION BOARDS, MCB's, RCCB's, CHANGE OVER etc. HSR 23.22.1 Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. HSR 23.22.1.3 TRIPLE POLE MCCB 16 to 100 Amp, 25 KA

HSR 23.22.2 MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of following ratings HSR 23.22.2.1 MCCB up to 125 A FP

HSR 23.22.4 Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to to the entire satisfaction of the Engineer-in-Charge of the work HSR 23.22.4.6 TPN DB Horizontal type Double Door 6 way ( 8 incoming 3phase*6 outgoing)

HSR 23.22.5 Supply and erection of miniature circuit Breaker/isolator 240/415 V in the existing distribution board including making necessary connections: HSR 23.22.5.1 6 amp to 32 amp Single pole

HSR 23.22.6 Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessary connections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work. HSR 23.22.6.2 DP RCCB 30ma sensitivity , 40 A

HSR 23.23.2 Supply of G.I Pipe (B-class) for suspansion rod of ceiling fan including threading if required. HSR 23.23.2.1 15 mm dia

HSR 24.1 E A R T H I N G HSR 24.1.3 Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

HSR 24.1.5 Extra for charcoal or coke and salt for G.I. Plate or copper plate earth electrode.

HSR 24.1.7 providing. and fixing 25 mm x 3 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode as required .

HSR 24.1.8 providing. and fixing 25 mm x 3 mm G.I. Strip on surface or in recess for connections etc. as required with all labour and material.

HSR 24.1.14 Supply and erection of 20mm x 3 mm thick GI, tape fixed with suitable G.I. staples of same size.

HSR 24.2.10 Supply & erection of cable route marker made of 50 cm long 10 mm dia M.S Rod welded/revitted at the top with 10 cm dia 5 mm thick G.I. plate inscribed with ‘cable’word on it, having a cross arm 30 cm long of the same dia welded at the bottom, in existing trench 45 cm below ground level.

NS 1 STC 20 W LED 1200 mm batten light. The Astra Fixture is a surface and wall mounted LED batten with extruded aluminium housing and robust comnstruction.PF0.95,system wattage LED 20 Watt with minimum 1500 lumens in 5700 k. The fixture should be of makes:- PHILIPS, CROMPTON, BAJAJ,Havells