Karnal Smart City Limited Tender

RECEPTION COUNTER (DINING) - Providing and fixing Reception Desk - 4000mm (L) x 850mm (H) x 600mm (W) - Providing and fixing of reception desk made in 18 mm with hardwood frame as required and finished with 4mm thick veneer with spray melamine polish of approved from outside and laminate finish from inside with two drawers and storage with shutter in laminate finish colour/shade complete as per design/dwg and instruction of Project in charge/ Architect. Table top to be in Nano Stone

TABLES REFURBISHMENT - SMALL (1000mm x 1000mm) - Installation of 15mm thk Engineered stone with adhesive of good strength on existing table top. Polishing the understructure and repairing if required complete as per Engineer incharge

TABLES REFURBISHMENT - BIG (1350x 760) -Installation of 15mm thk Engineered stone with adhesive of good strength on existing table top. Polishing the understructure and repairing if required complete as per Engineer incharge

TABLES REFURBISHMENT - BIG (1350x 760) -Installation of 15mm thk Engineered stone with adhesive of good strength on existing table top. Polishing the understructure and repairing if required complete as per Engineer incharge

SOFA REFURBISHMENT -Repairing the existing sofa with a layer of 2-3" foam and changing fabric ( Base rate of Fabric INR 500/ Mt) polishing the wooden structure and repairing if required as per Engineer Incharge

CHAIRS REFURBISHMENT - Repairing the existing chair with a layer of 2-3" foam and changing fabric ( Base rate of Fabric INR 500/ Mt) polishing the wooden structure and repairing if required as per Engineer Incharge

Providing & Installation of Bar Chairs Height AdjustmentWith HydraulicFrame and support made ofSS 202Chair TypeREVOLVINGTYPE OF SEATINGSEAT WITH INTEGARTED BACK RESTPadestal BaseStainless SteelFoot RestWithPadestal Base TypeWithout WheelsArmsWithoutMAX LOAD BEARING CAPACITY IN KGGenericHeight AdjustmentWith HydraulicFrame and support made ofSS 202Chair TypeREVOLVINGTYPE OF SEATINGSEAT WITH INTEGARTED BACK RESTPadestal BaseStainless SteelFoot RestWithPadestal Base TypeWithout WheelsArmsWithoutSEAT MATERIALCUSHIONED SEATDimensionsShape of SeatSquareSeat Size (mm x mm)450mm x 450mmHeight Adjustment in mm (+/- 5 mm)300Padestal Size / Diameter in mm (+/- 10 mm)500Seat Height At Lowest Position in mm (+/- 10 mm)550Thickness of Polyurethane Foam Used in Seat in mm (+/- 2 mm)50Density of Polyurethane Foam Used in Seat (Kg/Cub M)50MaterialMaterial of Fabric of Seat CoverLeatherineMISCPadestal Base Chrome PlatedyesColour of SeatBrownMAX LOAD BEARING CAPACITY IN KG110GSM/Thickness Of FabricNo FabricWARANTEE PERIOD IN NUMBER OF YEARS2

Providing & Installation of High Table -600 mm Diameter top & 1050mm high Table made of MS understructure powdercoated with Laminate Top fixed on the structure complete as per Engineers Incharge

Providing & Installation of Lounge Chair - Dimension 25" Diamater , 29" Ht , Seat Ht 16"Structure: Seat With Solid Wood With High Natural Rubber ContentElastic Strap Webbing. Backrest With Metal Insert Is Coated In Fire-Resistant Polyurethane FoamAnd The Seat In Variable Density Polyurethane Foam. Backrest AndSeat Cased In Breathable Heat Bonded Fibre Laminated To White Hypoallergenic Cotton Fabric ForAdded Softness.Cushions: Backrest Cushion Padding In Heat-Bonded Fiber With Center Insert In Polyurethane Foam.Covers: Backrest And Structure Cushion Upholstery Covers Are Completely Removable In All Versions (Fabric And Leather).Base/Legs: Metal Painted With A Polish Anti-Fingerprint Bronze Varnished. The Front Legs Are Protected By A Strip Of Curved Metal In The Same Finish As The Base. The Back Legs Have A Leather Or Saddle-Hide Trim.Adjustable Stainless-Steel Feet Painted Bronze Colour. Black Protective Polyethylene Glides.

Providing & Installation in place of Round CENTRE TABLE with Marble Top of 914mm(Dia) Number of storage under top:Single storage in bottom portion,Top material:Marble,Frame material:Stainless steel SS 304,Dimension of Top (length X Breadth) ±20mm:914mm(Dia),Height of centre table ±10 mm:430 millimeter,Thickness of top material (+/-2 mm):18 millimeter,Thickness of frame material (+/- 1 mm):18 millimeter,Warranty period in number of years 1.

Providing and installation in place of Table - GENERICShape of TableRectangularSeating Capacity 6 Seater MATERIALMaterial of topPrelaminated boardMaterial of understructureOther WoodMaterial of top finishMembraneDIMENSIONLength of table ±10mm (Diameter in case of Round)1500 mmDepth of table ±10mm900 mmHeight of table ±10mm735 mmThickness of top in mm (+/- 5%)20 mmShape and Dimension of BaseRECTANGULARMISCNumber of vertical support4Under Structure Diameter of Pipes (Width in case of Square sections) in mm60Vertical Support Diameter of Pipes (Width in case of Square sections) in mm50COLOUR & FINISHColour of top finishAS PER BUYER CHOICEWARRATYWarrantee period in number of years1-year

SOFA REFURBISHMENT (BAR) -Repairing the existing sofa with a layer of 2-3" foam and changing fabric ( Base rate of Fabric INR 500/ Mt) polishing the wooden structure and repairing if required as per Engineer Incharge

Providing and installation in place of Round Out Door Table - 450 mm Dia with 4 Armed Chair.8mm tempered glass on top,Table and Armchair Frame Material High Quality 18/20 Gauge Powder Coated Aluminium Material,Wicker Wave Material:High Density PE Rattan,Cushion Fabric 2 inch Foam 32 grade with Fabric PU Coated.Garden Umbrella with Base Size :8 Feet Round and 8 Feet Height Aluminium Powdercoated 180 gsm Polyster Acrylic.Weather Proof,Long Lasting,Superior Quality,High Performance,Smooth Finishing,Comfortable,Stylish,Light Weight

Supply & installation of 6 Seater - Outdoor Table Shape of Table Rectangular,Seating Capacity:6,Material of top:Ply, Material of understructure:Plywood,Material of top finish:Polish,Length of table ±10mm (Diameter in case of Round):2100 mm,Depth of table ±10mm:900 mm,Warrantee period in number of years:1-year.

Providing and installation in place of Wooden Chairs Dimensions, (L x W x H):33x18x18,Technical SpecificationsChairFeatures:Carving,Color:White,Style:Modern,Furniture Assembly:Already Assembled,Material:Wood.

Providing and installation in place of Chair Type 2 (Bar Type)Height AdjustmentWithout HydraulicFrame and support made ofPOWDER COATED MS TUBESChair TypeNON REVOLVINGTYPE OF SEATINGONLY SEATPadestal BaseAluminium Die CastFoot RestWithPadestal Base TypeWithout WheelsArmsWithoutMAX LOAD BEARING CAPACITY IN KG100

Providing and installation in place of Sofa Type 3 seater - Linear - Technical ParameterTable Top Glass TypeToughenedTable Top Glass Thickness8 millimeterTable and Armchair Frame MaterialHigh Quality 18/20 Gauge Powder Coated Aluminium MaterialProduct IncludedThree Seater SofaWicker RattanColour of Wicker RattanbrownWicker Wave MaterialHigh Density PE RattanCushionsColour of Cushionsoff whiteCushion Fabric2 inch Foam 32 grade with Fabric PU CoatedUsageOutdoorFrame MaterialAluminium Powdercoated 180 gsm Polyster AcrylicGenericFeaturesWeather Proof,Long Lasting,Superior Quality,High Performance,Smooth Finishing,Comfortable,Stylish,Light WeightAdditional ParameterSIZE -6X2

Providing and installation in place of Single Seater Sofa - Technical ParameterTable Top Glass TypeToughenedTable Top Glass Thickness8 millimeterTable and Armchair Frame MaterialHigh Quality 18/20 Gauge Powder Coated Aluminium MaterialProduct IncludedSingle Seater Comfort SofaWicker RattanColour of Wicker RattanbrownWicker Wave MaterialHigh Density PE RattanCushionsColour of Cushionsoff whiteCushion Fabric2 inch Foam 32 grade with Fabric PU CoatedGarden Umbrella With BaseSize8 Feet Round and 8 Feet HeightUsageOutdoorFrame MaterialAluminium Powdercoated 180 gsm Polyster AcrylicGenericFeaturesWeather Proof,Long Lasting,Superior Quality,High Performance,Smooth Finishing,Comfortable,Stylish,Light WeightAdditional Parametersofa with cushion

Providing and installation in place of DINING ROOM RECEPTION BACKDROP - Fabrication and fixing of 2800mm x 2800mm PVD coated ms art work aser cut jaali 1 mm thick in a niche 4000 mm wide , 3000 high, 150mm deep made of 19 mm plyboard cladded with veneer and finished iwith melamine polish and paint completeas per the instructions engineer incharge

Providing and installation in place of BAR ARCHES Refurbishment - Removal of existing wooden Arch Jaali and painting it in duco paint and refixing it along the façade with required support complete as per engineer incharge.

Providing and installation in place of BAR - Undercounter Cabinets - Fabrication and fixing 350mm deep counter understorage formed out of 19mm ply/board with laminated . Shutter of cabinet to be formed of 19mm thick commercial plywood/board laminated with 1mm thick laminate to approved shade. Shutter edges and all other exposed edges to be duly finished with 2mm thick PVC edge band (factory finished) as per details. Rear backing of cabinet to be formed with 12mm thick marine plywood.

Providing and installation in place of BAR cabinet with mirror panel - 3000 mm x 1500 mm - Fabrication and fixing of 250mm deep bottles display & storage made out in 18mm thick veneer cladded and polished with Mirror Back and shelves . Work complete in all respect as per detail drawing including all necessary hardwares and lighting provision

Providing and fixing Roller Blinds - Roller Blinds - [17:32, 25/02/2022] Neha Badiye: Hardware & MechanismTop Tube: Made of extruded aluminium 38mm dia. with wall thickness of 1.2mm with solineadoptable to accommodate clutch as manufacturer's approved make.Clutch Mechanism: Moulded plastic having antifriction additive with high strength Glass fiberreinforcement polyester and should have a minimum lifting capacity of 8 lbs. Clutch mechanismshall be crash proof, prevent slippage and shall raise and lower smoothly to any desired height.Operating Chain: #10 plastic/steel ball chain (or as per manufacturer's standard) adoptable to theclutch pitch for smooth, quiet lifting & lowering of blind.Locking Member: #12 steel stop locks for limit setting adoptable to the steel chain or as permanufacturer's standard.Bottom Bar /Weight: Aluminium extruded circular section with powder coated finish matching theroller fabric -Min weight to be 365 gms / Rmt for a perfect fall of fabric to avoid warpage / floating.Installation to be insert type with end caps to give a neat look.SPRING BOOSTERS: All blinds above 2.4mtr width or 2.8mtr height and for total weight exceeding4.0 kgs shall be provided with spring boosters as per manufacturers standard.[17:33, 25/02/2022] Neha Badiye: Roller BlindsFabricFabric shade: as approvedFabric Composition: 30% Polyester, 70% Vinyl on PolyesterOpenness factor/ Light transmission : 5%Thickness.ISO 2286: 0.55-0.65 mm ‡ 5%Weight/m?ISO 2286 : 460gms/m? + 5%Fire rating of the fabric : Class - 1, (M1:NFP 92 503)Width : 250 cm-310 cm as per manufacturer standardMechanical Resistance:BreakingISO 1421 : Warp 35 daN/5 cmWeft 120 daN/5 cmFolding ..ISO 1421 : Warp ≥ 30 daN/5 cmWeft 2 100 daN/5 cmColor fastness to Light..ISO 105 B02 • 7/8Shade Orientation: Regular roll, shade cloth falls at window side of roller.Configuration: Single band75mm closure with up-stand along the length of the dry pocket, removable type for servicing shadesas per manufacturer specification.[17:34, 25/02/2022] Neha Badiye: FabricFabric shade: as approvedFabric Composition: 100% Polyester with Acrylic foam coated as per manufacturer standard.Openness factor/Light Transmission : 0%, BlackoutThicknessISO 2286: 0.33-0,45 mm ‡ 5%Weight/m?- ISO 2286: 380gm/m? + 5%Fire rating of the fabric : Class - A, NFPA - 701 TMWidth : 180-250cm as per manufacturer standardDimensional stability: Warp: 1Weft : 1Color fastness to Light......ISO 105 B02 - 5/6Shade Orientation: Regular roll, shade cloth falls at window side of roller.Confiquration: Single band75mm closure with up-stand along the length of the dry pocket, removable type for servicing shadesas per manufacturer specification.

Providing & laying POP Moulding work on walls as per drawing & as directed by engineer in charge.

Providing and Fixing WPC Panelling in place size of each pannel (2900x204x14mm),all work done as per directed by engineer in charge.

Wooden Paneling - Supply and Installation of Veneer Paneling and moulding with polish as per the detail in drawing as directed by engineer in charge .

Providing & fixing SS Handels in Glass Door.

Providing & Fixing Stainless Steel Glass To Glass Door Lock Without Cutout.

Providing and fixing of TOILET CUBICLE - Toilet Cubicle Made Of Heat, Bacteria, Water Chemical, Scratch, Impact & Anti Bacterial Resistant 12mm Thick Solid Compact Laminate Panels Included Doors, Pilasters & Intermediate Panels.Toilet cubicle I Shape (Front Partition) with standard dimension of Upto1950mm height x 1200mm width x 1500mm depth which includes 550-600mm door size widthDoors :1,Vertical Pilaster:2,U / Door Channels & Top Rail :- SS 304 Grade as per plan,Foot Assembly :- Shoe Box SS 316 Grade :2,Door lock with indicator SS 304 Grade 1,Door Knob SS 304 Grade :1,Self Closing Gravity Hinges SS 304 Grade:3,Coat Hook SS 304 Grade:1,Screws SS 304 Grade as per plan.

Providing and fixing of URINAL PARTITION - Made Of Heat, Bacteria, Water Chemical, Scratch, Impact & Anti Bacterial Resistant 12Mm Thick , size 900W x 450D with all fitting.

Mirror Cladding : Providing & pasting 6 mm thk mirror on 4" thick board boxing with making provision for light and including cutting , edge polish & pasting complete as & where required as per design.

Providing & fixing 12 mm toughend glass railing with SS post and handrail with necessary hardware.

BAR Counter Overhead Metal Storage - Providing and fixing 400 mm high , 300 mm deep metal storage made out of 12mm ms pipe powder coated inmetallic color as specified with lighting detail covered with acrylic sheet , fixed from ceiling support above Bar Counter complete with necessary hardware as per Enginner Incharge .

Rougheneing of Granite with Grinder

Reinstallation of AC with all necessary missing items complete. Gas to be paid seprately.

BAR Counter Overhead Metal Storage - Providing and fixing 400 mm high , 300 mm deep SS structure PVD coated with lighting detail covered with acrylic . The base of the structure to have veneer finished ply board and top to have Laminate fixed plyboard hung from ceiling support with MS framing above Bar Counter complete with necessary hardware as per Enginner Incharge

BAR Counter Finishing - Providing and fixing 8 mm thick flexi ply on existing bar counter then layering 18 mm thick 40 mm wide strips on ply facia with appropriate adhesive and hardware as required. These strips to be finished with good quality Duco paint complete as per the instructions of enigneer incharge . All painting surfaces shall be sand papered and cleaned thoroughly. The pores,scratches etc. shall be filled and smoothened properly. A coat of surfacer (Duco P.S. Grey) shallbe applied evenly. Then surfaces shall be sand papered and cleaned. A coat on N.C. putty shallbe evenly and allowed to dry completely. The water polishing with the help of water – proofemery paper shall be carried out to obtain uniform smooth/even surface. Second coat of ducopaint shall be applied after drying and cleaning of the first coat. Proper care shall be taken so thatno dust, dirt etc. settles down on finished surfaces. The final surface shall be finished even andmat finished. The thinner and putty used shall be Duco only. Rubbing and polishing of thepainted surfaces shall be done with waxpol/duco rubbing and wax polish till the surface finish isobtained. If the plaster surface is to be finished with plaster of Paris punning, the surface shall becombed slightly with the wire brushes or nails before it is completely set to form key for plaster ofParis punning. The surface shall be thoroughly cleaned of dust then only damped but not soakedbefore the application of plaster of paris punning. The Gypsum for preparing punning shall beapproved quality. It shall be dry and free from lumps and shall be suitably packed in watertightbags or containers. Paste shall be prepared by adding required quantum of water and same shallbe used before it sets. No dropping paste shall be used in the work. Punning shall be applied tothe prepared surface with steel trowel to a thickness required to make the surface produceperfectly smooth and even surface working from top to bottom. It shall then be sand papered togive a smooth and even surface. Any unevenness shall be made good by applying putty, madeof plaster of paris mixed with water, and then sand papering the same after it is dry. Filling inplaster shall be made good with plaster of paris mixed with colour to be used. The surface shallthen be rubbed down again with a fine grade sand paper and made smooth. The surface shall beallowed to dry thoroughly before the regular coat of paint is applied.

Providing and Fixing of acrelic letter(With Lighting) of height of 500-600mm in existing MS base plate as per Design and Drawing approved by Engineer in Charge.

Providing and fixing 12 mm thick frameless Antiglare toughened glass of approved brand and manufacture, including providing and fixing top & bottom complete as per direction of Engineer-in-charge

Providing & Fixing HANDRYER Hi Speed Black.

Providing & Fixing PAPER DISPENSER.

Providing and fixing Sensor based Faucet 15 mm Pillar Mounting Combination Tap Assembly conforming to IS:8931: Latest for wash basin.Approved make: Jaquar,hindware,cera,,kohler.

Providing & fixing Urinals with inbuilt sensor flushing make sure of your safety through a touch-free and hygienic experience.(Hindware - 60021 Flow Sensor Urinal) all fitting complete.Approved make: Jaquar,hindware,cera,kohler.

Providing and fixing washbasin with waste coupling 32 mm and bottle trap A ring shaped orbicular design that graces the bathroom counter with utmost elegance, the Solitaire over counter WBs is everything your bathroom needs and more.The sleek curves are enhanced by a centre pre punched hole and chrome plated cap for overflow hole.This 46X46X15 cm design is suitable bothe for luxe and compact spaces.(Hindware- Solitaire Over Counter Basin 91064) Approved make: Jaquar,hindware,cera,,kohler.

Main LT Panel : Fabrication, supplying and installation of outdoor type cubical panel board of suitable size made out of GI sheet 2 mm thick (14 SWG) and powder coated thereafter, duly compartmentalised having door locking arrangement for protection from rain, dust, duly fixed on GI angle iron frame work of size 50 mm x 50 mm x 6 mm (NS) and having following accessories mounted inside the panel including connection, inter connection with aluminium thimbles, earthing with two nos. earth studs, duly powder coated complete etc. as required, Civil Foundation cost for the panel shall be inclusive. Cable gland plates shall be provided on bottom. 2 Nos. earthing terminals shall be provided. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system, lifting hooks shall also be provided in case of large panels with surge arrestor. 160A FP MCCB, 415 V, 50 Hz. : 2 Nos 160 A 4P Contractor 415 V, 50Hz.: 2 Nos With Electro Mechanical Interlocking arrangment Indication & digital metering 160TP + N Aluminium sectionalised BUS suitable for 1.1 K V with a fault level with-stand: 20 KA for 1 second. The Earth Bus shall be of AL & run contInuously throughout the width of the panel. Outgoing : 63 A, 4Pole, 50 Hz, MCB : 1 Nos. 40 A, 4Pole, 50 Hz, MCB : 5 Nos. 32 A, DPPole, 50 Hz, MCB : 3 Nos. Indication lamps (RYB) with control MCB - 03 Sets Danger notice plate Make : As listed in UHBVNL

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 3.5Cx50 sqmm AL Ar Cable

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 4C x 25sqmm Al Ar cable

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 4C x 16sqmm Al Ar cable

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 4C x 6sqmm Al Ar cable

Supply of following size XLPE insulated, 1100V grade armoured alluminium cable as per specification confirming to IS:7098 (Part - I) 3C x 4sqmm Cu Flex cable

Supply Installation Of Type A lights.Refer S. No. 1 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Type B lights .Refer S. No. 2 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Wall Lights Refer S. No. 3 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Down Lighters 12 W Refer S. No. 4 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Cove Lights Refer S. No. 5 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Type C Refer S. No. 6 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Type D - Golden Glass Globe Refer S. No. 7 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Cove Lights Refer S. No. 8 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Down Lighters - 12 WRefer S. No. 9 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Chandelier - Ht 3 MtsRefer S. No. 10 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Down Lighters Refer S. No. 11 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installation of Lobby Refer S. No. 12 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installationas of Down lighters - 12 WRefer S. No. 13 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installationas of Surface Lights - 30 WRefer S. No. 14 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installationas of Surface Lights - 12 WRefer S. No. 15 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installationas of Batten Lights in Kitchen and Store - 20 W (Ground Floor & First Floor)Refer S. No. 16 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installationas of Concealed Downligter Lights - 12 WRefer S. No. 17 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installationas of Surface Lights - 12 WRefer S. No. 18 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply Installationas of Concealed Downligter Lights - 12 W Refer S. No. 19 of Volume VI - Technical Specifications of RFP for “Typical graphical representation of Interior Lights”

Supply and Installation of 4mtr high URBAN ARCHITECTURE LIGHTING DECORATIVE POLE BJPL with 140 mm bottom diameter & 60 mm top diameter Black painted Galvanised pole in different cross section with gold colour painted decorative cast aluminium rings. Base plate is welded to pole with 4 nos. mounting holes. Supply of 4nos of M16X450 long 'J' type EN 8 grade foundation bolts along with template. Supply of Bakelite sheet with 1Nos of 6A SP MCB and stud type connector suitable for 4Cx 16Sq mm cable. Make : Bajaj / Valmont / VAK/Valmont

Supply Installationas per annexure I Sr.No 20 in RfP LED post top made in cast aluminium with decorative opal polycarbonate diffuser with IP 65 protection. 40W LED or equivalent. Make : Bajaj / Surya/HPL/VAK/Philips

SITC of energy efficient fan, 1200 mm sweep, aluminium body, consuming 28 W, BEE 5 star rated, ceiling fan with Brush Less Direct Current(BLDC)motor, class of insulation: B, 3 no's blades, 30 cm long down rod, 2 no's canopies, suitable for 230V, 50 HZ, single phase AC supply, earthing etc., including all standard accessories etc., complete.

Supply & fixing of 10KVA UPS with 30mins battery back up with racks complete

Supply & fixing of EXHAUST FANS 300MM SWEEP

Netwrok Video Recorder (NVR)32 CHANNEL NVR 4 SATA WITH HDMI AND VGA PORTS IP VIDEO INPUT 32-CH UP TO 12 MP RESOLUTION TWO-WAY AUDIO 1-CH, RCA (2.0 VP-P, 1 K Ω)Network Incoming bandwidth - 320Mbps,Outgoing bandwidth-256 Mbps,Recording resolution:12 MP/8 MP/6 MP/5 MP/4 MP /3MP /1080p /UXGA/720p/VGA /4CIF/DCIF/2CIF/CIF/QCIF,Video & audio output: HDMI1/VGA1,output resolution :HDMI1: 4K (3840 × 2160)/60Hz, 4K (3840 × 2160)/30Hz, 2K (2560 ×1440)/60Hz, 1920 × 1080p/60Hz, 1600 × 1200/60Hz, 1280 × 1024/60Hz, 1280 × 720/60Hz, 1024 × 768/60HzHDMI2 output resolution : 1920 × 1080p/60Hz, 1280 × 1024/60Hz,1280 × 720/60Hz, 1024 × 768/60Hz,Decoding format: H.265+/H.265/H.264+/H.264/MPEG4,Live view/ Playback: 12 MP/8 MP/6 MP/5 MP/4 MP/3 MP /1080p /UXGA/720p/VGA/4CIF/DCIF/2CIF/CIF/QCIF,Network protocols: TCP/IP, DHCP, Hik- Connect, DNS, DDNS, NTP, SADP, SNMP, SMTP, NFS, iSCSI, UPnP™, HTTPS Hard disk capacity SATA: 4 sata 4 hdd Up to 8 TB capacity for each HDD,Network interface:1 RJ-45 10/100/1000 Mbps self-adaptive Ethernet interfaceWorking temperature:-10 °C to 55 °C (14 °F to 131 °F),Power supply: 100 to 240 VAC 1 no. (SP 10/16A MCB)Model: HIKVISION DS-7732NI-I4 OR Equivalent

2MP NETWORK BULLET CCTV1/2.8" progressive scan CMOSUp to 2.0 megapixel2.8 mm/4 mm/6 mm fixed focal lens Up to 30 m IR rangeDual streamDigital WDR (Wide Dynamic Range)3D DNR (Digital Noise Reduction)PoE (Power over Ethernet)IP67Mobile monitoring via Hik-Connect or iVMS-4500Day &Night IR cut filter with auto switchMax. Resolution: 1920 × 1080Protocols: TCP/IP, ICMP, HTTP, HTTPS, FTP, DHCP, DNS, DDNS, RTP, RTSP, RTCP,NTP, UPnP, SMTP, IGMPOperating Conditions: -30 °C to 60 °C (-22 °F to 140 °F), humidity: 95% or less (noncondensing)IR Range: Up to 30 m MAKE: HIKVISION / CP Plus

2 MP Full HD WDR IR Vandal Dome Camera - 30Mtr.Feature SpecificationImage Sensor 1/2.8” 2MP Progressive scan CMOSEffective Pixels 1920(H) x 1080(V)Minimum Illumination 0.006Lux/F1.4 0.005Lux/F1.2( Color,1/3s,30IRE) 0.05Lux/F1.4 0.04Lux/F1.2(Color,1/30s,30IRE) 0Lux/F1.4(IR on, B/W)Shutter Speed Auto/Manual, 1/3~1/100000sWhite Balance Auto/Natural/Street Lamp/Outdoor/ManualLens 2.7mm~13.5mm motorized LensGain Control (AGC) Auto/ManualAngle of View H:106°~29°, V:57°~17°Video Compression H.265+/H.265/H.264+/H.264H/MJPEG (Sub Stream)Back Light Compensation BLC / HLC / WDR(120dB)S/N Ratio More than 50dBVideo Streaming 1080P (1 ~ 25/30fps) , D1/CIF(1 ~ 25/30fps) , D1/CIF(1 ~ 25/30fps)Resolution1080P(1920x1080)/SXGA(1280×1024)/1.3M(1280× 960)/720P(1280×720)/D1(704×576/704×480)/ VGA(640×480)CIF(352×288/352×240)Digital Zoom 16xMotion detection Off / On (4 Zone, Rectangle)Privacy Mask Off / On (4 Area, Rectangle)ICR Auto (ICR)/Color/B/WROI Off / On (4 Zone)Audio Input 1Ch.Audio Output 1Ch.Audio Compression G.711A;G.711Mu;G.726;AACAlarm IN 1 channel In: 5mA 5VDCAlarm Out 1 channel Out: 300mA 12VDCBit Rate H.265: 12K ~ 6400Kbps , H.264: 32K ~ 10240KbpsProtocolHTTP; HTTPs; TCP; ARP; RTSP; RTP; RTCP; UDP; SMTP; FTP; DHCP; DNS; DDNS; PPPoE; IPv4/v6;QoS; UPnP; NTP; Bonjour; IEEE 802.1x; Multicast; ICMP; IGMP; ONVIF Profile S&G, API ,TLSSmart Detection Tripwire, IntrusionEvent Trigger Motion detection, Video tampering, Scene changing, Network disconnection, IP addressconflict, Illegal access, Storage anomalyEthernet RJ-45 (10/100Base-T)User Account 20 UsersSmart Phone iPhone, iPad, Android PhoneIR IR Range of 30 Mtr. ,Smart IRMicro SD Micro SD Card128GBOperating Temperature -30°C~+60°C , Less than 95%RHPower Source DC12V, PoE (802.3af)MAKE: HIKVISION / CP PlusPower Consumption 9WCasing MetalWeatherproof Standard IP67 & IK10Dimension φ122mm x 88.9mmWeight 0.4Kg

POE SWITECH : POWER ON ETHERNETNetgear GS110TP ProSafe 8-PortGigabit PoESmartwith 190W Power-over-Ethernet budget and 2 SFP ports for wireless converged networks, IP surveillance and mobility,2 dedicated Gigabit SFP fiber ports.Make : NETGEAR / Dlink / TP link

24 PORT PATCH PANEL : NETWORK MANAGERPreferred Make : D'LINK/ NETGEAR/TPLINK

RACK 2U : TO MOUNT POE SWITCH HARDWARE CABLE MANAGER + FAN + 4 PORT POWER STRIP

LED monitor - 44 inch (Make : LG/SAMSUNG/SONY)

DATA TRANSMITION CAT-6 Cable Armoured with 25mm dia PVC conduits pipe with all required accessories (bends, flexble conduits, Junction box etc)

WARRANTY 4.5 Kg C02 Gas Type Fire Extinguisher, Trolley Mounted, Easy Weight Providing Management used Unused Mechanism, Squeeze Grip, Gross weight 19.1 Kg, empty Weight 14.6 Kg, Can Height 857MM Diameter 140MM, Discharge Time Less than 10 Sees, Controllable discharge· ('mechanism, Applicable on Class B&C Fire, B Rating 218, Can Constrution :Hot spinning/Forging, Value Construction: Forging & Machining, Internal Coating of Can : Not Apllicable, External Coating of Can : Spray Painting, Sheet metal thickness : 4.5 MM lSI Approved, 1 Year Warranty.

Supply & Erection of mild steel bucket stand suitable for 4 Nos. fire set buckets including the cost of welding and painting of complete stand will one coat of red oxide and 2 coats of approved paint of red colour with all labour and material required to complete the job in all respect up to the entire Satisfaction engineer in charge of the work (size 4'x4' made of GI pipe 32mm dia).

PA Music - Amplifier : Two Zone PA Amplifier with Built-in Digital Player Model. TZA-7000DP (700Watts,350W+350W RMS) With USB, MMC Card Reader and Remote Control

PA Music - Speakers : Philips/JBL/ Pioneer PA Dual Sound Speaker

PA System - Cable : Speaker Audio Cable 1.5Sqmm 2 Core 100 Meters Roll Make. Bestnet White

PA Music - Microphone :UHF Wireless Microphone

PA Music - Installation Testing & Commsissioning of above equipmets includes installation of Speakers on existing 9mtr street light pole at 6mtr height with suitable powder coated with galvanised clamps. Making of suitable size of holes on pole for cable entry with proper packing (silica gel) upto the complete satisfaction of Engineer in charge.

VRV System - OUTDOOR UNIT Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/ Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R410A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V+/-10%, 3Phase, 50HzAC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5

VRV System - INDOOR UNIT-CASSETTE TYPE Supply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeedmotor, coilsection with DX Coppercoil , electronic expansion valve, outer cabinet, drainpump, grill, necessary supports, vibration isolation, cordless remote controletc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27Degree CDB and 19Degree CWB temperature. 1.6TR

VRV System - INDOOR UNIT-CASSETTE TYPESupply, installation, testing and commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeedmotor, coilsection with DX Coppercoil , electronic expansion valve, outer cabinet, drainpump, grill, necessary supports, vibration isolation, cordless remote controletc., suitable for operation on single phase 230V±10%, 50Hz AC supply, complete, as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27Degree CDB and 19Degree CWB temperature. 3.6 TR

VRV System - COPEER REFRIGERANT PIPING Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines, all accessories as per specifications etc. as required : 15.86mm dia (OD) (Softdrawn) with tube thickness 1.2mm with 19mm thick insulation

VRV System - Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines, all accessories as per specifications etc. as required : 19mm dia (OD) (Softdrawn) with tube thickness 1.2mm with 19mm thick insulation

VRV System - Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/ with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquidlines, all accessories as per specifications etc. as required : 25.4mm dia (OD) (Softdrawn) with tube thickness 1.2mm with 19mm thick insulation