Irrigation And Water Resources Department Tender

Providing, lowering, laying, aligning, fixing in position and jointing at all level/ depths ISI marked HDPE pipe of 355 mm outer dia of PE-100 grade and PN-6 for water supply as per IS 4984-2016 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends , tees required during laying of pipe line along required alignment

Providing, lowering, laying, aligning, fixing in position and jointing at all level/ depths ISI marked HDPE pipe of 200 mm outer dia of PE-80 grade and PN-4 for water supply as per IS 4984-2016 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends , tees required during laying of pipe line along required alignment.

Providing, lowering, laying, aligning, fixing in position and jointing at all level/ depths ISI marked HDPE pipe of 280 mm outer dia of PE-80 grade and PN-4 for water supply as per IS 4984-2016 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends , tees required during laying of pipe line along required alignment.

Providing, lowering, laying, aligning, fixing in position and jointing at all level/ depths ISI marked HDPE pipe of 200 mm outer dia of PE-80 grade and PN-4 for water supply as per IS 4984-2016 (amended up to date) in trenches in complete including cost of HDPE Specials, labour, sectional hydro testing (including the cost and conveyance of water to site for testing) and commissioning as per Technical Specifications and as per direction of Engineer. Note: E/w to be measured and paid separately. Rate includes cost of all specials like bends , tees required during laying of pipe line along required alignment.

Supply erection testing and commissioning of 300mm i/d Electronic FLOW METER (KRONE Make) with digital display including all other required accessories complete complete in respect to the satisfaction of EngineerIn-Charge.

Supply, erection and commissioning of LTDB of capacity 400 Amp. With the main incomer MCCB of 400 Amp and 4 No outgoing of 300 Amp each. Ampere meter, voltmeter, push buttons indicator relay in main LTDB Including 3 No. fully automatic ATS Starter suitable for operation of 3 No. 65 HP motors with suitable size MCCB/MCB/contactors of sufficient capacity and MCB 63 amp for lighting loads and main contactor of sufficient capacities, indicators, relays, voltmeters, ammeters, power factor meter, Push buttons, timers, bus bars, suitable capacitor bank of 25KVar ( 01 no. for each starter) including suitable size cable for capacitor bank and 95 sq mm cable from starter panel to motors 50 meter, Thimbles, Nut and Bolt lugs etc. suitable for operation of 3 No. Motors of capacity of 65 HP. LTDB will be installed on MS stand 1 feet from ground including all left over items if any as per site requirement and approved by the technical committee.

2700 LPM Erection and commissioning of Solid shaft motor of capacity 65 or suitable HP,3 phase ,440/415 Volt Horizontal motor with split pumping set for canal water having head 60 mtr as per the indicated requirements of discharge in cusec and power capacity in HP Make: KSB, CRI, Kirloskar, Crompton Greeves, BCH, Lubi) with proper foundation and third party inspection from CEIL/rites/Govt. agency

Operation and maintenance cost of project/work for 1 year.

Operation and Maintenance for Project for 3 years after 1 year defect liability to be paid yearly @ 2% per annum