Haryana Urban Development Authority Tender

24.2.1 LT CABLE 1. Supply & erection of LT phase separator on LT line complete in all respect up to entire satisfaction of the Engineer-in-charge of the work. [Through Rate]

24.3.4.2 HT CABLE 4.2. Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 150 to 185 sqmm [Through Rate]

24.5.2.3 MISCELLANEOUS ITEMS 2.3. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia [Through Rate]

23.22.1.3 MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.3. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. TRIPLE POLE MCCB 16 to 100 Amp, 25 KA [Through Rate]

23.22.5.1 MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole [Through Rate]

23.27.3 Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 3. M.S. pedestal of size 750 mm wide , 1200 mm high ,300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level , having a base of size 1050 mm x 600 mm x 250 mm below ground level . 0 0 [Through Rate]

Job Work Supply and Erection of Galavanized steel item Nut and Bolts etc. including cutting, bending to the required shape, drilling hole, carriage, loading-unloading complete in all respect upto the entire satisfaction of Engineer-in-charge.(Excluding GST)

Job Work Supply and Erection of Galavanized steel item (Flat, Angle, Channel) etc. including cutting, bending to the required shape, drilling hole, carriage, loading-unloading complete in all respect upto the entire satisfaction of Engineer-in-charge.(Excluding GST)

Job Work Supply and Erection of PCC pole as per IS:1678-1960 specifications, 11Mtr. Long 140mm x 200mm at top and 140mm × 400mm at bottom with working load of 400 Kg buried 2.20 M in ground as per DHBVNL specification.(Excluding GST)

Job Work Supply, Stringing and Sagging 8 SWG G.I. Earth wire complete in all respect to the entire satisfaction of Engineer-in-charge conforming to IS 298/1978 and 7807/1973 and with latest amendment thereof. (Excluding GST)

Job Work Supply and Erection of Cradle Guard made of GI wire with Guard Reel including fixing in the LT line complete in all respect up to the satisfaction of Engineer-in-charge. (Excluding GST)

Job Work Supply and Erection of GI D-Strap as per DHBVN design and specifications complete in all respect upto the entire satisfaction of Engineer-In-Charge (Excluding GST).

Job Work Supply and Erection of shackle insulator as per DHBVN specification complete in all respect (Excluding GST).

Job Work Supply and Erection of top hamper suitable for 11 Mtr. Long PCC pole and 11kV system made out of GI flat size 50×6mm (A shapes) having weight 2.95 kg as per approved design and drawing of DHBVN complete in all respect (Excluding GST).

Job Work Supply and Erection of G.I. V-shape cross arm suitable for 11 KV system made of out of G.I. channel of size 100x50x50x6mm (ICMC100) as per design and drawing of DHBVN 13.2 kg. 2 Nos. 18mm dia holes provided in the base for fixing of half clamp 2 Nos. holes 22mm dia for GI pin on the flange shall be provided on the top and bottom flanges of both end of V-shape X-arm complete in all respect (Excluding GST).

Job Work Supply and Erection of Cradle Guard made of GI wire of SWG including fixing in 11kV line complete in all respect up to satisfaction of Engineer-in-charge. (Excluding GST)

Job Work Supply and Erection of 11kV polymeric Pin insulator 10 kN with GI Pin of approved makes/ specification of DHBVN (Excluding GST).

Job Work Supply and Erection of 11 KV polymeric disc insulator 45 KN for 11 KV over head lines with fittings, TandC type and complete with galvanized strain clamps, bolts, nuts, washers etc. as required as per DHBVN specification (Excluding GST).

Job Work Supply and erection of 11kV Lightning Arrester as per approved makes and relevant specifications of DHBVN complete fixing with GI clamp, Nut and bolts upto entire satisfaction of Engineer-In-Charge (Excluding GST).

Job Work Supply and Erection of 11 kV G.O. Switch vertical mounted with heavy duty 9 Nos. post insulators suitable copper male and female contacts fixed on GI angle frame with G.I. Nut and Bolts including G.I. pipe and operating handle complete in all respect (Excluding GST).

Job Work Supply and Erection of LT PVC unarmoured cable of size 300 Sqmm single core with aluminium conductor 650/1100 V conforming to ISS 1554 (Part-I) of 1988 IS: 7098/Part-1/ 1988 with latest amendments upto entire satisfaction of Engineer-in-charge (Make: Grandlay, Polycab, Havells, CIRTINA (Excluding GST).

Job Work Supply and erection of L.T. Aerial Bunched cable of size 120 Sqmm, 4 core plus 95 Sqmm including making of necessary connection of make Polycab, Havell’s, Grandlay complete in all respect upto the entire satisfaction of Engineer-in-charge(Excluding GST).

Job Work Supply and Erection of wooden cleats of size 4” wide 1’-6” long complete with 4 Nos. holes suitable to pass through 300/400 Sqmm single core cable complete in all respect upto the entire satisfaction of Engineer-in-charge (Excluding GST).

Job Work Supply and erection of bracket 1 Mtr long made of 32mm dia (Nominal), medium gauge G.I. pipe for fixing of street light fitting on 9 Mtr long PCC poles including cost of 6 Nos. GI nut and bolts with two nos. clamps made of 50x6mm GI flat complete in all respect upto the entire satisfaction of the Engineer-in-charge (Excluding GST)..

Job Work Supply and erection of bracket 1 Mtr long made of 40mm dia (Nominal), medium gauge G.I. pipe for fixing of street light fitting on 9 Mtr long PCC poles including cost of 6 Nos. GI nut and bolts with two nos. clamps made of 50x6mm GI flat complete in all respect upto the entire satisfaction of the Engineer-in-charge (Excluding GST).

Job Work Supply and Erection of 25 Watt pressure die cast aluminium housing LED street light fitting luminaire with multiple LED lenses and leat resislant polycarboniate. Cover glass IP65 of complete in all respect as per specifications having light efficiency of 120 lumens / watt upto the entire satisfaction of Engineer-in-charge of the work Make: Bajaj / Philips / LT (with 3 year free replacement warranty, mtc. including labour charges, free of cost). (Excluding GST).

Job Work Supply, erection, testing and commissioning of ELEX-TWS-2EXT / Amson’s make Automatic electric timer to switch ON/OFF the street light / road light automatically. It should have lux level adjustable switch, with extensible mountable sensor. It will change ON/OFF timing automatically as per lux level of season throughout the year as purchase in the timing of sun-rising and sun setting suitable for street / road light. It will have three Nos. LandT make, 3 pole power contactor model MNX-25 to control 25 amp. Per phase with 220 Volt coils. It will have auto/manual switching mode for repair of street light during day time and the whole unit fixed on Bakelite sheet to assemble the components etc. The erection of the complete unit in the existing pedestal with complete wiring upto the satisfaction of the Engineer-in-charge (Excluding GST).

Job Work Supply and Erection of ACSR conductor 100mm2 IS 398 (Part-II) 1976/1996, IS 4826-1976 IS 1521-1972 and IS 1778-1980 with latest amendments as per DHBVN specification including stringing and sagging as well as jointing and binding with insulators at supports complete in all respect upto the entire satisfaction of Engineer-in-Charge (Excluding GST).

Job Work Supply and Erection of ACSR conductor 80mm2 IS 398 (Part-II) 1976/1996, IS 4826-1976 IS 1521-1972 and IS 1778-1980 with latest amendments as per DHBVN specification including stringing and sagging as well as jointing and binding with insulators at supports complete in all respect upto the entire satisfaction of Engineer-in-Charge (Excluding GST).

Job Work Supply and Erection of ACSR conductor 50mm2 IS 398 (Part-II) 1976/1996, IS 4826-1976 IS 1521-1972 and IS 1778-1980 with latest amendments as per DHBVN specification including stringing and sagging as well as jointing and binding with insulators at supports complete in all respect upto the entire satisfaction of Engineer-in-Charge (Excluding GST).

Job Work Supply and Erection of ACSR conductor 30mm2 PVC insulated conforming to IS 398 (Part-II) 1976/1996, IS 4826-1976 IS 1521-1972 and IS 1778-1980 with latest amendments as per DHBVN specification including stringing and sagging as well as jointing and binding with insulators at supports complete in all respect upto the entire satisfaction of Engineer-in-Charge (Excluding GST).

Job Work Supply and Erection of 9 Mtr. Long 105mm x 115mm at top and 105mm × 315mm at bottom with working load of 200 Kg. buried 1.80 M in ground or as DHBVNL specification.(Excluding GST)

Job Work Supply and Erection of Stay set for LT line complete with GSS 7/8 SWG, Egg, insulator/ Disc Insulator, GI rod 20mm dia threaded up to 250mm length with GI Nut (wt.6.224kg), GI cross plate 460 mm of GI Channel 75×40×6mm (wt.5.330kg), GI Elbow (wt.2.240kg), GI clamp with GI Nut-Bolts etc. as per DHBVN specification complete in all respect up to the entire satisfaction of Engineer-in-charge. (Excluding GST)

Job Work Supply and Erection of Stay set for HT line complete with GSS 7/8 SWG, Egg, insulator/ Disc Insulator, GI rod 20mm dia threaded up to 250mm length with GI Nut (wt.6.224kg), GI cross plate 460 mm of GI Channel 75×40×6mm (wt.5.330kg), GI Elbow (wt.2.240kg), GI clamp with GI Nut-Bolts etc. as per DHBVN specification complete in all respect up to the entire satisfaction of Engineer-in-charge. (Excluding GST)

Job Work Supply and erection of of PVC flexible aluminium wire of size 2.50 Sqmm single core complete in all respect as per standard specification upto the entire satisfaction of Engineer-in-Charge (Excluding GST)

Job Work Supply, installation, testing, commissioning of 3 Phase 11KV/0.433 KV-250V, 200 KVA Oil immersed, naturally cooled, Aluminum Wound Outdoor type Distribution Transformers with CSP (Completely self protected ) features with external microprocessor based four pole MCCB 300Amp. To 400Amp., 50kA strictly conforming to Nigam’s technical specification No. CSC-V/R-I/DH/UH/P and D/2010-2011 read with amendment thereof and as per relevant ISS as amended from time to time and losses conforming to 4 star rating of BEE as per appd. Specification of DHBVN/UHBVN including installation of transformer on existing platform upto the entire satisfaction of Engineer-in-Charge. Valtage Rated Frequency Permitted at 75ºC i) Maximum load looses at 50% load at 75ºC = 780 Watt ii) Maximum losses at 100% load at 75ºC = 2300 Watt iii) Warranty = 72 Months shall be one time The above losses are maximum allowable and there would not be any positive tolerance. (Excluding GST)

Job Work Supply and Erection of fuse unit of L.T. side suitable for 200 kVA transformer as per DHBVN specifications complete with wooden board, aluminium bus bar GI clamps and GI nut and bolts including all petty material required up to the entire satisfaction of Engineer-in-charge(Excluding GST).

Job Work Supply and Erection of 185 Sqmm x 3 core 11 KV TR-XLPE cable (earthed), stranded compact circular, Aluminium conductor, screened with extruded semi-conducting compound, XLPE insulated, galavanised steel flat armoured and overall PVC sheathed cable conforming to ISI 7098 (Part-2) 2011 with upto date amendments, loose in existing pipe or trench including making necessary connections complete in all respect upto the entire satisfaction of Engineer-In-Charge of the work Make: Havells, Grandlay, CCI (Excluding GST).

Job Work Supply and Erection of 70/72 Watt Street light luminaire with multiple LED with lighting efficient with power LED light with lens pressure die cast aluminium housing, reflector and enclosed with polycarbonate/ toughened glass, IP-66 level, having light efficiency of 120 lumens / watt upto the entire satisfaction of Engineer-in-charge of the work Make: Bajaj / Philips / LT (with 3 year free replacement warranty, mtc. including labour charges, free of cost) (Excluding GST).

Job Work supply and erection of G.I. pipe 100mm dia (nominal) ISI marked (medium gauge) laid 1 mtr below ground level including digging and refilling of trench complete in all respect(Excluding GST)

Job Work Supply and erection of pvc insulated and sheathed underground cable of size 25 sqmmx 4 core armoured,loose in existing pipe or trenche 1100 volt grade having aluminium conductor wires conforming to IS: 694:2010,including making necessary connections complete in all respect up to entire satisfaction of the Engineer-In-Charge of the work .make : Havells,Grandley,Polycab (Excluding GST)