Haryana Urban Development Authority Tender

[23.22.5.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.1. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole [Through Rate]

[23.22.5.2]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 5.2. Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. Single Pole [Through Rate]

[23.24.3.5]MS STAND, BUS BAR CHAMBER AND PANELS 3.5. Supply and erection of metal clad bus bar chamber made from 1.6 mm thick M.S. sheet and fixing with rag bolts on wall or on existing pedestal/angle iron frame including bonding, detachable top and bottom including painting and necessary connection etc. (Aluminium bars). 200 amp 4 bars of 55 cm each (cross section 38 mm x 6 mm) chamber over all size 60 cm x 45 cm x 18cm [Through Rate]

[23.26.2]SAFETY ITEMS 2. Supply and erection of High Tension Voltage caution notice plate of size 250*200 mm in three languages. [Through Rate]

[23.27.3]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 3. M.S. pedestal of size 750 mm wide , 1200 mm high ,300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level , having a base of size 1050 mm x 600 mm x 250 mm below ground level . 0 0 [Through Rate]

[23.6.6.4]MS CONDUIT PIPE ONLY (SURFACE OR RECESSED) FOR ELECTRICAL POINTS 6.4. Supply and erection of MS conduit pipe 1.6 mm thick , ISI marked surface/recessed in slab/wall/ceiling etc. including cost of MS bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work. MS pipe of 40 mm dia. [Through Rate]

[24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. [Through Rate]

[24.1.13]EARTHING AND LIGHTENING ARRESTOR 13. Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as required. [Through Rate]

[24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required. [Through Rate]

[24.1.8]EARTHING AND LIGHTENING ARRESTOR 8. Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material. [Through Rate]

[24.2.8.4]LT CABLE 8.4. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 16 sqmm [Through Rate]

[24.2.8.5]LT CABLE 8.5. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 25 sqmm [Through Rate]

[24.2.8.7]LT CABLE 8.7. Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire satisfaction of the Engineer-in-charge of the work. 50 sqmm [Through Rate]

[24.4.8.7]STREET LIGHT 8.7. Supply and erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with base plate including cost of nut and bolts , earthing studs, Integral Cable termination arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2 no 10 A SP MCB , end cover and all accessories as supplied by the manufacture including Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 9 Metre Long pole with top dia 100 mm and bottom 200 mm with base plate of size 350 x 350 x 20 mm. [Through Rate]

[24.5.2.3]MISCELLANEOUS ITEMS 2.3. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia [Through Rate]

Supply and erection of PCC pole as per IS: 1678-1960 specifications, 11Mtr. long 140mm x 200mm at top and 140mm x 400mm at bottom with working load of 400Kg buried 2.20M in ground or as per UHBVNL specification .

Supply and erection of cradle guards made of 8 S.W.G. confirming to ISS 280/1978/1973 with latest amendments complete in all respect up to the entire satisfaction of Engineer-in-Charge. For HT Line

Supply and erection of 11 KV lighting arrestor as per relevant ISS specification

Supply and erection of stay set for LT/HT Line complete in all respect with G.I. stay wire( rope of 7 wires of 8 SWG G.I. Wire), egg/Disc insulator , G.I. rod of 20mm dia 8’ long threaded up-to 250mm long with nut (weight 6.224 kg) with cross plate of 460mm of angle 65x65x6 mm(weight 5.33 kg), elbow (weight 2.24 kg ) complete with clamps , nuts and bolts complete in all respect up-to the entire satisfaction to Engineer-in-Charge of the work. HT Stay

Supply and erection of 11 KV brown glazed 10 KN pin insulator with GI pin/ silicon type as per specification and approved make by DHBVN.

Supply and erection of V-shape X-arm suitable for 11KV system made of out of 1650mm long MS channel of size 100x50x50x6mm as per design and drawing 2 Nos. 18mm dia holes provided in the base for fixing of half clamp made of MS flat of size 50x6mm and 2 Nos. holes 22mm dia for GI Pin on the flange plate of MS Flat of size 50x6mm shall be provided on the top and bottom flanges of both end of V-shape X-arm with 22mm hole in the plate complete in all respect including primer and aluminum paint.

Supply and erection of top hamper suitable for 11 Mtr. long PCC pole and 11KV system made out of MS flat size 50x6mm (A shapes) having approx weight 2.5 kg as per approved design and drawing including primer and alum paint complete all respect.

Supply and erection of fuse unit of L.T. side suitable for 200 KVA transformer complete with wooden board cleats, aluminum strips MS clamps and MS nut and bolts including all petty material required up-to the entire satisfaction of Engineer-in-Charge.

Supply and erection of ACSR conductor conforming to IS 398 (Part-II) 1976/1996, IS 4826-1976 IS 1521-1972 and IS 1778-1980 with latest amendments and erection of the same with accessories including stringing and sagging of conductor of various sizes i.e. 100mm2/80mm2/50mm2/30mm2/30mm2 PVC insulated as well as jointing and binding with insulator at supports in all respect up to the entire satisfaction of Engineer-in-Charge. 100sqmm ACSR

Supply and erection of anti climbing barbed wire of size 12x12 gauge (6.33 Mtr. = 1.00 kg) for 11 KV/33KV Poles complete in all respect

Supply and erection of Disc insulator with fitting on PCC pole of approved make of State Electricity Nigam requirement to complete in all respect to confirming to ISS 731/1971 latest amendment thereto.

Supply and erection of PVC insulated sheathed 50 Sqmm aluminum conductor cable single core 1100 volts grade in existing pipe, complete in all respect up to entire satisfaction of the Engineer-in-Charge of the work.

Supply and erection of P.G clamp Al cast 2 bolt suitable for 50/80/100 Sqmm ACSR conductor complete in all respect up to entire satisfaction of the Engineer-in-Charge of the work.

Supply and erection of Prodigy type in-built L.T. C.T. meter of (40- 200 amps), 3-phase 415 Volts rating suitable for 3-phase, 4-wire system of make Secure, Genus or other make approved by the UHBVNL. The meter is to be fixed in M.S Sheet cubical meter box on existing PCC Pole. This includes all petty material i.e. M-Seal, Nut–Bolts, thimbles etc. Meter will be got tested from the UHBVNL lab by the contractor after depositing the meter testing fee by him and it will be refunded on production of receipt received from UHBVNL.

Supply, erection, testing and commissioning of ELEX-TWS-2EXT / Amson’s/LandT make Automatic electric timer to switch ON/OFF the street light automatically. It should have adjustable lux level switch, with extensible mountable sensor. It shall change ON/OFF timing automatically as per lux level of the Sun at sun-rising and sun setting, throughout the year. Shall have two Nos. LandT make, 3 pole power contactor model MNX-70 to control 70 amp per phase with 220 Volt coils. It shall have auto/manual switch for repair of street light during day time. The whole unit components to be assembled on Bakelite sheet with 16 amp capacity MCB to save the time switch. The erection of the complete unit in the existing pedestal with complete wiring upto the entire satisfaction of the Engineer-in-charge. ON/OFF Timer

Supply and erection of Suspension clamp Dead end clamps and eye belts for sagging of 11KV XLPE Aerial Bunched cable suitable for 50sqmm x 3 core to 240 sqmm x 3 Nos complete in al respect upto the entire satisfaction of Engineer-in-charge of the work Suspension clamp 50sqmm to 240 sqmm

Supply and erection of Suspension clamp Dead end clamps and eye belts for sagging of 11KV XLPE Aerial Bunched cable suitable for 50sqmm x 3 core to 240 sqmm x 3 Nos complete in al respect upto the entire satisfaction of Engineer-in-charge of the work Eye bolt 50sqmm to 240sqmm

Supply, stringing and sagging of 8 SWG G.I. earth wire as per complete in all respect to the entire satisfaction of Engineer-in-Charge conforming to IS 298/1978 and 7807/1973 and with latest amendment thereof. (Excluding GST)

Supply and Erection of 11 kV G.O. Switch vertical mounted with heavy duty 9 Nos. post insulators suitable copper male and female contacts fixed on GI angle frame with G.I. Nut and Bolts including G.I. pipe and operating handle complete in all respect (Excluding GST).

Supply and erection of round type hot dip galvanized bracket of 0.75 mtr radios made out of 50 mm dia G.I. Pipe and canopy of size 0.6 mtr long made out of 125 mm dia G.I. Pipe complete with all labour , nut and bolts and all other petty items on existing octagonal / M.S. Pole complete in all respect up to entire satisfaction of the Engineer-in-Charge of the work. ( EXCUDING GST)

Supply and erection LT AB cable of size 25 sqmm x 4 core plus 25 sqmm with necessary connection complete in all respect up to the entire satisfaction of Engineer-in-charge of the work.(MAKE- Havell's/Polycab/Grandlay)

Supply, installation, testing, commissioning and handing over 63 KVA transformers, voltage ratio 11KV/433V, 3Phase 4 wire 50Hz. Alum. Wound oil immersed natural cooled, outdoor type, distribution energy level-3 as per UHBVN technical specification no CSR-142/DH/UH/PandD/2015-16 and as per IS:1180 part-1/2014 with latest amendment thereof 4-Star Rating distribution transformer complete with fitting and accessories including filling of oil as per all other specification up to entire satisfaction of engineer-in-charge of work. Approved – UH/DHBVN specification make. (Without GST )

Supply and erection of Double Arm over-hang galvanized iron pipe bracket having canopy of B-class G.I. pipe, 0.60m long,125mm dia. Each arm the bracket to be of length 1500mm, made out of 50mm dia, B-class G.I. pipe, including 150mm long nipple for LED street light fitting if required, making an angle of 15 degree with horizontal plane including nut-bolts and all other petty material, labour charges etc. complete in all respect upto the entire satisfaction of Engineer-in-Charge. (WITH-OUT GST)

Supply and erection of PVC insulated and sheathed underground cable, loose in existing pipe or trenches 1100 volts core having solid aluminium conductor wires confirming to IS: 694:2010, including making necessary connections complete in all respect up to entire satisfaction of the Engineer-in-Charge of the work. Cable Size: 25 Sqmm x 4-core (Armd.). Make: Grandlay/Polycab/Havell`s. (Without GST)

Supply and erection of PVC insulated and sheathed underground cable, loose in existing pipe or trenches 1100 volts core having solid aluminium conductor wires confirming to IS: 694:2010, including making necessary connections complete in all respect up to entire satisfaction of the Engineer-in-Charge of the work. Cable Size: 16 Sqmm x 4-core (Armd.). Make: Grandlay/Polycab/Havell`s. (Without GST)

Supply and erection of 120 watt LED Street light luminaire with multiple highly efficient and high power LED light with individual lens, pressure die cast aluminum housing with heat sink and aluminum extrusion, with secondary optics and enclosed with toughened glass, IP-66 level, having 120 lumens/watt, with 3 years defect liability period (on site replacement) free of cost, complete in all respect up to the entire satisfaction of Engineer-in-charge of the work. Make:- Philips/Bajaj//LT/Panasonic/Anchor - (Rate without GST)

Supply and erection of 120 watt LED Flood Light luminaire with multiple highly efficient and high power LED light with individual lens, pressure die cast aluminum housing with heat sink and aluminum extrusion, with secondary optics and enclosed with toughened glass, IP-66 level, having 120 lumens/watt, with 3 years defect liability period (on site replacement) free of cost, complete in all respect up to the entire satisfaction of Engineer-in-charge of the work. Make:- Philips/Bajaj//LT/Panasonic/Anchor - (Rate without GST)

Supply and erection of FR, PVC insulated and sheathed underground cable, loose in existing pipe or trenches 1100 volts core having solid aluminium conductor wires confirming to IS: 694:2010, including making necessary connections complete in all respect up to entire satisfaction of the Engineer-in-Charge of the work. Cable Size: 50 Sqmm x 4-core (Armd.). Make: Grandlay/Polycab/Havell`s. (Without GST)

Supply and erection of 2.5 Sqmm x 3-core (Unarmd.) PVC insulated and sheathed Aluminium conductor service cable 1100 volts, having single solid aluminium conductor in each core as per IS:694, complete in all respect up to entire satisfaction of the Engineer-in-Charge of the work. Make: Polycab, Havell`s, Grandlay. (Excluding GST).