Haryana Urban Development Authority Tender

WALL SHELVES Supply, erection & Commissioning in place of, WALL SHELVES, Overall Size 1650X300mm. Shelves is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet

CLEAN DISH TABLE Supply, erection & Commissioning in place of, CLEAN DISH TABLE , Overall Size 1350x675x850+ 150mmTable is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Two sides & Front to be turned down 50 mm and in 12 mm, & Back side 150 mm high back splash. turned back at 90 by 20mm & 12mm, UNDER SHELVES: 2 in Nos. full length and full width to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, directly to Uprights & middle at centre of Top & bottom Shelf. The bottom of under shelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick MS angle for rigidity. The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia. X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAME WORK in 32x32x3mm thick Stainless Steel AISI 202 Grade Angle alround below and the table the Top and with stainless steel AISI 202 grade 50x3 mm flats at 450 mm c/c for rigidity. 1100X550X850+100mm ht., TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash. turned back at 90 by 20mm & 12mm, UNDER SHELVES: 1 in No. full length and full width to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, with 32x32X3mm thick Stainless Steel AISI 202 Grade Angle below the shelf on two sides welded to uprights in 38 mm dia. x 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAME WORK in 32x32X3mm thick Stainless Steel AISI 202 Grade Angle below the Top.

WIPING TABLE WITH1 Under Shelves Supply, erection & Commissioning in place of, VIPING TABLE WITH1 Under Shelves, Overall Size:1500 X 675 X 850 +150. Backsplash TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash .turned back at 90 by 20mm & 12mm, UNDER SHELVES: 1 in Nos. full length and full width to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, directly to Uprights & middle at centre of Top & bottom Shelf. The bottom of under shelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick MS angle for rigigdity. The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick Stainless Steel AISI 202 Grade Angle alround below and the table the Top and with stainless steel AISI 202 grade 50x3 mm flats at 450 mm c/c for rigidity.

FOUR SHELVES RACK Supply, erection & Commissioning in place of, FOUR SHELVES RACK, Overall Size 750X 450 X 1800mm SHELVES: 4 in No. to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, Rear & Two sides to be turned up 38 mm at 90 and in 12 mm for chipping bend. Front Side turned down 38 mm at 90 and in 12 mm Bottom Shelf Welded at 150mm from Bottom of Unit, directly to Uprights, INTERNAL FRAMEWORK:. Top shelf at the top of upright & centre equidistant to top & bottom shelves. Second at 500mm from bottom of unit, Top Shelf at the Top of Upright & Rest Two Equidistant to top & Second Shelves. UPRIGHTS in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment.

FIVE SHELVES RACK Supply, erection & Commissioning in place of, FIVE SHELVES RACK, Overall Size 750 X 450 X 1800mm SHELVES: 5 in No. to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, Rear & Two sides to be turned up 38 mm at 90 and in 12 mm for chipping bend. Front Side turned down 38 mm at 90 and in 12 mm Bottom Shelf Welded at 150mm from Bottom of Unit, directly to Uprights, INTERNAL FRAMEWORK: The bottom of under shelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick MS angle for rigidity’s cross braces shall be welded to uprights. Top shelf at the top of upright & centre equidistant to top & bottom shelves. Second at 500mm from bottom of unit, Top Shelf at the Top of Upright & Rest Two Equidistant to top & Second Shelves. UPRIGHTS in 38 mm dia x 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment.

THREE SHELVES POT RACK Supply, erection & Commissioning in place of, THREE SHELVES POT RACK, Overall Size 1200 X 600 X 1500 mm SHELVES: 3 in No. to be Fabricated from 38 mm dia. x 16SWG thick Stainless Steel AISI 304 grade pipe square frame with pipes .UPRIGHTS in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. The legs shall be braced with 38 mm dia.X 16 SWG thick stainless steel AISI 304 grade pipe alround at appropriate level

Onion and potato bin Supply, erection & Commissioning in place of, Onion and potato bin: Overall dimensions of 1000x1000x1000, excluding 150 high all direction heavy duty castors with brakes on one pair of castors. The outer frame shall be fabricated of 40x40x3 thick ss angle, properly finished in TIG welding, and the bin shall be made of 25x25 grid hevy duty ss grill. The bin should have a projected pouring mouth of 200 high, towards the lower front, and the top to have a hinged door with handle. The pouring mouth as well as top door should be given a locking provision. One internal vertical partition to be provided for separating onions and potatoes.

TWO DOOR VERTICAL REFRIGERATOR Supply, erection & Commissioning in place of, TWO DOOR VERTICAL REFRIGERATOR: Over all dimensions of 750 X 750 X 2000 (all approximate), capacity of 500 Litres, 2 doors, 4 shelves, delivered temperature range from 1 to -5 degrees celcius, compressor rate for 200 W, single phase, operating on Jaipoor capper wrapping refrigeration system. Outer of 20 swg and inner of 22 swg SS sheet, with poly urethane foam in-situ insulation of 50 mm thickness. Legs to be fitted with 100 high adjustable bullets. Compressor to be of Kirloskar or Tecumseh brand

MILK WARMER VESSEL Supply, erection & Commissioning in place of, MILK WARMER VESSEL, 25 LIT. CAPACITY Operated by Electrical 3 kw heater. It is a cylindrical type vessel. Double jacketed. The inner and outer containers are fabricated with 16 SWG AISI 304 Grade Stainless Steel Sheet. It is provided with steam injection terminal, drain nipple, safety valve.

WATER BOILER, 40 LITRE Supply, erection & Commissioning in place of, WATER BOILER, 40 LITRE. The INNER BOILING CHAMBER Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, PROVISION OF 12mm water inlet, 12mm outlet faucet (non leaking, heat resistant), glass water level indicator, etc OUTER CLADDING & TOP LID Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, INSULATION with Non Sagging Glasswool, ELECTRICAL:1 X 3 KW Single Phase Water Emmersion heater, On / Off Switch, Indicator Lamps, Thermostat (ambient - 110 C range

CUTTING CHOPPING TABLE 6-SEATER CARD TABLE Supply, erection & Commissioning in place of, CUTTING CHOPPING TABLE, Overall Size:1500 X 675 X 850 Backsplash TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash .turned back at 90 by 20mm & 12mm, UNDER SHELVES: 1 in Nos. full length and full width to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, directly to Uprights & middle at centre of Top & bottom Shelf. The bottom of under shelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick MS angle for rigigdity. The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia. x 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick Stainless Steel AISI 202 Grade Angle alround below and the table the Top and with stainless steel AISI 202 grade 50x3 mm flats at 450 mm c/c for rigidity

TABLE WITH SINK Supply, erection & Commissioning in place of, TABLE WITH SINK on Left hand side , Overall Size: 1200 X 675 X 850 as below :TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Sunk in Top with Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash .turned back at 90 by 20mm & 12mm, UNDERSHELVES: 1 in No. to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, The bottom of undershelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick stainless steel AISI 202 grade angle for rigigdity. The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia. x 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick Stainless Steel AISI 202 Grade Angle below the Top. Sink Bowl: Size- 600x600x300mm deep Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, with all bottom & sides edges rounded at 38mm dia the Bowl Welded to Top securedly with removal of all holes or burr & finished properly to give a uniform look. Provision of 50 mm dia sunk with drain holes at bottom centre of the bowl and stainless steel coupling with gate valve of 50 mm dia. of approved make.

TABLE FOR KNEADING Supply, erection & Commissioning in place of, TABLE FOR KNEADING WITH 2 Under Shelves, Overall Size:1350 X 675 X 850 as mentioned below. Backsplash TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash. turned back at 90 by 20mm & 12mm, UNDER SHELVES: 2 in Nos. full length and full width to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, directly to Uprights & middle at centre of Top & bottom Shelf. The bottom of undershelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick MS steel AISI 202 grade angle for rigigdity. The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia. x 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick Stainless Steel AISI 202 Grade Angle alround below and the table the Top and with stainless steel AISI 202 grade 50x3 mm flats at 450 mm c/c for rigidity

TABLE WITH SINK Supply, erection & Commissioning in place of, TABLE WITH SINK on Left hand side , Overall Size: 600 X 675 X 850 + 150 as below :TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Sunk in Top with Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash. turned back at 90 by 20mm & 12mm, UNDER SHELVES: 1 in No. to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, The bottom of undershelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick stainless steel AISI 202 grade angle for rigigdity .The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia. x 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick Stainless Steel AISI 202 Grade Angle below the Top. Sink Bowl: Size- 600x600x300mm deep Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, with all bottom & sides edges rounded at 38mm dia the Bowl Welded to Top securedly with removal of all holes or burr & finished properly to give a uniform look. Provision of 50 mm dia sunk with drain holes at bottom centre of the bowl and stainless steel coupling with gate valve of 50 mm dia. of approved make.

DOSA PLATE, LPG OPERATED Supply, erection & Commissioning in place of, DOSA PLATE, LPG OPERATED, Overall Size:1100X675X850+100mm ht. Backsplash TOP: DOSA Plate in 16mm thick Mild Steel of size 900x500mm, All sides shall be provided with oil drip channel of size 50mm wide x 35mm deep with a oil drain on front side, A Splash Guard of 100mm turned back 20mm & down 20mm The drip channel and splash guard both to be fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet. SIDE SKIRTING: in 18SWG Stainless Steel AISI 304 Grade Sheet, Provision of Ignition window in front skirting of size 150x150 on one side centre for burner ignition. UNDER SHELF: One no. full length and full width in 18SWG Stainless Steel AISI 304 Grade Sheet welded at 150 mm from FFLwith 32x32X3mm thick Stainless Steel AISI 202 Grade Angle below the under shelf on two sides welded to uprights UPRIGHTS: in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK: in 32x32X3mm Angle, 25x3 mm thick Flat in Stainless Steel AISI 202 Grade. BURNERS & FITTINGS: Two nos. V-900 type burners “UNITED” or equivalent, with individual Needle Control Valve (3/8 BSPTM X 3/8 Cu), Copper Pigtail (Suitable Length) internal gas pipeline of 12 mm dia. NB with ERW mild steel pipe 'C' Class "TATA" or approved make

Two burner cooking range Supply, erection & Commissioning in place of Two burner cooking range. Overall dimensions of 1200x675x850. Top to have one each of T-35 and G-35 burners, housed properly in a suitable ms frame, with pilot lamps, internal gas piping, wire braided pig tails, gas flow regulators, and each burner to have a 500x500 heavy duty cast iron vessel rest rated for 20 kgs per square foot. Legs to be of 38 mm dia 16 swg ss pipes, fitted with adjustable ss bullet feet. Bottom frame of cross bracings made by 25 mm dia 16 swg ss pipes welded at 150 intervals, 150 above floor level.

BULK COOKING RANGE Supply, erection & Commissioning in place of, BULK COOKING RANGE, Overall Size: 600X600 X 850 TOP: to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. SIDE SKIRTING: in 18SWG Stainless Steel AISI 304 Grade Sheet. UNDER SHELF: One no. with 25 mm dia pipe alround and 20 mm dia pipe @ 150 mm c/c (16 swg) along the length of the unit welded to uprights at 150 mm from FFL DRIP TRAY: independent below the burner in 18SWG Stainless Steel AISI 304 Grade Sheet. UPRIGHTS in 38 mm dia. x 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm Angle, 25x3 mm thick Flat in Stainless Steel AISI 202 Grade. PAN SUPPORTS: independent for the burner, 450x450mm Square ring with 8 support flanges both in Cast Iron. BURNERS & FITTINGS: One no. T -35 burner or One no. M - 35 burner, "UNITED" brand or equivalent and the burner provided with Individual Pilot Burner, Needle Control Valve (3/8 BSPTM X 3/8 Cu), Copper Pigtail (Suitable Length) internal gas pipeline of 12 mm dia. NB with ERW mild steel pipe 'C' Class "TATA" or approved

Two burner cooking range Supply, erection & Commissioning in place of Two burner cooking range. Overall dimensions of 1200x750x850. Top to have one each of T-35 and G-35 burners, housed properly in a suitable ms frame, with pilot lamps, internal gas piping, wire braided pig tails, gas flow regulators, and each burner to have a 500x500 heavy duty cast iron vessel rest rated for 20 kgs per square foot. Legs to be of 38 mm dia 16 swg ss pipes, fitted with adjustable ss bullet feet. Bottom frame of cross bracings made by 25 mm dia 16 swg ss pipes welded at 150 intervals, 150 above floor level.

THREE BR. CHINESE COOKING RANGE Supply, erection & Commissioning in place of THREE BR. CHINESE COOKING RANGE Overall dimensions of 1700 X 750 X 850+15" height. Top to have two high pressure Chinese burners with 15” dia heavy duty cast iron grids and one stock burner fitted in between the high pressure burners towards the rear, and to have 10” dia heavy duty cast iron grids. Each burner to have individual control regulator, and internal copper gas piping. All controls and regulators to be positioned on the front skirting of 20 Swg stainless steel, up to 12” from top and rear to have a splash back of 15” height. Top of the unit to have drain channel of 4” wide 2” deep, sloping towards the front right, collection of drain water through 1” dia vertical 16 Swg. stainless steel pipe connected to the floor drain. Unit to be mounted on MS angle frame work of 1.5X1.5X3 mm, given two coats of red oxide and finished in stone hammer grey. Legs to be of 1.5” dia 16 Swg. stainless steel pipes, fitted with nylon bussets. Pipe bracings of 3/4” dia 16Swg. stainless steel pipe.

HOT AIR Exhaust hood Supply, erection & Commissioning in place of HOT AIR Exhaust hood Overall outer dimensions of 4000 x 1750 X 550 ,height at front 300 and rear 450 to 600 mm. Hood shall be fabricated in 20 Swg ss sheet and TIG welded for seamless finish. It shall be fitted with a thermally protected tube light fitting, to provide 150 LUX on the cooking surface. Front over- hang of the hood shall be designed to capture maximum exhaust air. The hood shall have a condensate tray with detachable drain collector pan. Filters shall be of staggered baffle type for oil elimination, with minimum pressure loss and large surface contact area to increase the capture area. Frame of the filter shall be made of 20 swg ss sheet, and baffles in 22 swg ss sheet. Hood shall be given a suitable cut out as per site conditions and duct design for quick connection to the extraction duct

WORK TABLE Size1950 X 750 X 850 Supply, erection & Commissioning in place of, WORK TABLE WITH 1 Under Shelves, Overall Size1950 X 750 X 850 : as mentioned below. Backsplash TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash. turned back at 90 by 20mm & 12mm, UNDER SHELVES: 1 in Nos. full length and full width to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, directly to Uprights & middle at centre of Top & bottom Shelf. The bottom of undershelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick stainless steel AISI 202 grade angle for rigigdity. The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick MS Angle alround below and the table the Top and with stainless steel AISI 202 grade 50x3 mm flats at 450 mm c/c for rigidity.

SANDWICH GRILLER Supply, erection & Commissioning in place of, SANDWICH GRILLER. Overall Size335 X 345. as mentioned below with stainless steel outer body . The equipment should have cast iron plate non stick quoting with top and bottom grilling mechanism and also have insulated body with all necessary accessories.

SINGLE FAT FRYER Supply, erection & Commissioning in place of SINGLE FAT FRYER Overall dimensions 8 LTR. ELECTRICAL OPERATED .TABLE TOP MODEL. FITTED WITH 2 KW HEATEING ELEMENT.

IDLY STEAMER Supply, erection & Commissioning in place, IDLY STEAMER, For 54 pcs idly capacityAll three boxes of 18idlies each in 1x3 configuration Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, Each Box shall hold 4 no of Trays with 20 pockets of 90mm dia x 7mm deep for idlies made from 19SWG Stainless Steel AISI 304 Grade Sheet, Backed with drip trays made from 21SWG Stainless Steel AISI 304 Grade Sheet,.The inner and outer walls of the unit on all sides shall be filled with 75 mm thick non-sagging mineral glasswool. The door shutters of all three boxes shall be provided with 16 SWG double wall stainless steel sheet with 40 mm thick mineral glasswool in- between. The doors shall be provided with hard rubber beading alround ,tightly closing handles in stainless steel with a PVC knob at the end of the handle rod and a separate knob/ handle at the centre of the shutter.

WORK TABLE Size: 800 X 800 X 850 Supply, erection & Commissioning in place of, WORK TABLE WITH 1 Under Shelves, Overall Size800 X 800 X 850 : as mentioned below. Backsplash TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash. turned back at 90 by 20mm & 12mm, UNDER SHELVES: 1 in Nos. full length and full width to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, directly to Uprights & middle at centre of Top & bottom Shelf. The bottom of undershelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick stainless steel AISI 202 grade angle for rigigdity. The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick MS Angle alround below and the table the Top and with stainless steel AISI 202 grade 50x3 mm flats at 450 mm c/c for rigidity.

EARTHEN POT TANDOOR WITH SS CLADDING Supply, erection & Commissioning in place of, CHARCOAL EARTHEN POT TANDOOR WITH SS CLADDING, Overall Size:800 X 800 X900mm ht Outer Body of the Unit fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Inner Lining of the Unit fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, Top & All Sides insulated with non sagging mineral Glasswool, 75mm thick. Internal Framework in 35x35x5 mm thick MS Angle, Heavy duty charcoal heated commercial clay Tandoor with 500mm dia top mouth of capacity 2530 rotis, properly seasoned.Space between Tandoor Pot & side Box properly packed with glassspices, salt, brickbats, etc. Top 15mm thick Granite piece with 500mm opening for pot & a Mild Steel Ring Fixed. Provision of Lid with Handle. ash removal window at front bottom. CASTOR WHEELS: 2 Fixed & 2 Swivelling with Brake of 125mm dia x 30mm thick rubber tyres.

GRIDDLE PLATE Size750 X 600 X 850 Supply, erection & Commissioning in place of, GRIDDLE PLATE. Overall Size750 X 600 X 850 : as mentioned below TOP: Griddle Plate in 16mm thick Mild Steel of size 600 x500mm, All sides shall be provided with oil drip channel of size 50mm wide x 35mm deep with a oil drain on front side, A Splash Guard of 100mm turned back 20mm & down 20mm The drip channel and splash guard both to be fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet. SIDE SKIRTING: in 18SWG Stainless Steel AISI 304 Grade Sheet, Provision of Ignition window in front skirting of size 150x150 on one side centre for burner ignition. UNDERSHELF: One no. full length and full width in 18SWG Stainless Steel AISI 304 Grade Sheet welded at 150 mm from FFL with 32x32X3mm thick Stainless Steel AISI 202 Grade Angle below the under shelf on two sides welded to uprights UPRIGHTS: in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK: in 32x32X3mm Angle, BURNERS &FITTINGS: Two nos. V-450 type burners “UNITED” or equivalent, with individual Needle Control Valve (3/8 BSPTM X 3/8 Cu), Copper Pigtail (Suitable Lenght) internal gas pipeline of 12 mm dia. NB with ERW mildsteel pipe 'C' Class "TATA" or approved make 25x3 mm thick Flat in Stainless Steel AISI

DOUGH KNEADER 25 KG Supply, erection & Commissioning in place of, DOUGH KNEADER 25 KG. With 2.0 hp cg make motor . Kneading drum should have 304 swg stainless steel. Gear box with all accessories.

Exhaust hood Supply, erection & Commissioning in place of Exhaust hood Overall outer dimensions of 4600 x 1000 X 550 ,height at front 300 and rear 450 to 600 mm. Hood shall be fabricated in 20 Swg ss sheet and TIG welded for seamless finish. It shall be fitted with a thermally protected tube light fitting, to provide 150 LUX on the cooking surface. Front over- hang of the hood shall be designed to capture maximum exhaust air. The hood shall have a condensate tray with detachable drain collector pan. Filters shall be of staggered baffle type for oil elimination, with minimum pressure loss and large surface contact area to increase the capture area. Frame of the filter shall be made of 20 swg ss sheet, and baffles in 22 swg ss sheet. Hood shall be given a suitable cut out as per site conditions and duct design for quick connection to the extraction duct

STORAGE TABLE WITH CABINET AND DRAWER Supply, erection & Commissioning in place of, STORAGE TABLE WITH CABINET AND DRAWER, Overall Size1800 X 675 X 850 : as mentioned below. Backsplash TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash. turned back at 90 by 20mm & 12mm, UNDERSHELVES: 1 in Nos. full length and full width to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, directly to Uprights & middle at centre of Top & bottom Shelf. The bottom of undershelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick stainless steel AISI 202 grade angle for rigigdity. The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick MS Angle alround below and the table the Top and with stainless steel AISI 202 grade 50x3 mm flats at 450 mm c/c for rigidity.

WORK TABLE WITH SINK Supply, erection & Commissioning in place of, WORK TABLE WITH SINK on Left hand side , Overall Size:1700 X 675 X 850 as below :TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Sunk in Top with Two sides & Front to be turned down 50 mm and in 12 mm, & Back side 100 mm high back splash.turned back at 90 by 20mm & 12mm, UNDERSHELVES: 1 in No. to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit,The bottom of undershelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick stainless steel AISI 202 grade angle for rigigdity.The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick Stainless Steel AISI 202 Grade Angle below the Top. Sink Bowl: Size- 600x600x300mm deep Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, with all bottom & sides edges rounded at 38mm dia the Bowl Welded to Top securedly with removal of all holes or burr & finished properly to give a uniform look. Provision of 50 mm dia sunk with drain holes at bottom centre of the bowl and stainless steel coupling with gate valve of 50 mm dia. of approved make.

UNDER COUNTER REFRIGERATOR Supply, erection & Commissioning in place of, UNDER COUNTER REFRIGERATOR. Overall Size:1500 x 675 x 850 as mentioned below. Approximate capacity of 400 Litres, 3 doors, 4 shelves, delivered temperature range from 1 to -5 degrees celcius, compressor rate for 200 W, single phase, operating on Jaipoor capper wrapping refrigeration system. Outer of 20 swg and inner of 22 swg SS sheet, with poly urethane foam in-situ insulation of 50 mm thickness. Legs to be fitted with 100 high adjustable bullets. Compressor to be of Kirloskar or Tecumseh brand

WALL SHELVES Size:2700 x 300 Supply, erection & Commissioning in place of, WALL SHELVES. Overall Size:2700 x 300 as mentioned below. Shelves is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet.

ICE CREAM STORAGE COUNTER Size: 1200x600 x 750 Supply, erection & Commissioning in place of, ICE CREAM STORAGE COUNTER of branded company like Voltas or Bluestar. Overall Size: 1200 x 600 x 750

WORK TABLE WITH SINK Size:1050 x 600 x 850 Supply, erection & Commissioning in place of, WORK TABLE WITH SINK on Left hand side , Overall Size:1050 x 600 x 850 as below :TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Sunk in Top with Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash .turned back at 90 by 20mm & 12mm, UNDERSHELVES: 1 in No. to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, The bottom of undershelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick stainless steel AISI 202 grade angle for rigigdity. The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick Stainless Steel AISI 202 Grade Angle below the Top. Sink Bowl: Size- 600x600x300mm deep Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, with all bottom & sides edges rounded at 38mm dia the Bowl Welded to Top securedly with removal of all holes or burr & finished properly to give a uniform look. Provision of 50 mm dia sunk with drain holes at bottom centre of the bowl and stainless steel coupling with gate valve of 50 mm dia. of approved make.

FOUR DOOR VERTICAL REFRIGERATOR Over All Size: 1200 X 750 X 2000 INTERIOR 20 SWG 304 stainless steel sheet EXTERIOR 2() SWG 304 stainless steel sheet. BACK The back and underside of the unit shall be in 22 swg SS 304 sheet. CONDENSING UNIT Emerson Copeland make sealed compressor COOLING Static. MOTOR TEMPERATURE 1 HP, AUE fan motor, fan cooled condenser GAUGE Sub zero make digital. SHELVES the unit. 3 Nos. stainless steel rod shelves (removable type) shall be provided to Locking arrangement. The doors of the unit shall be provided SS heavy duty handle with INSULATION The unit shall be PUF insulated ACCESSORIES The unit shall have drain waste in bottom with drip tray.

SINGLE BURNER RANGE Size: 675 x 675 x 850 ht. Supply, erection & Commissioning in place of, SINGLE BURNER RANGE Overall Size: 675 x 675 x 850 ht. TOP: to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 50 mm and in 12 mm. SIDE SKIRTING: in 18SWG Stainless Steel AISI 304 Grade Sheet. UNDERSHELF: One no. with 25 mm dia pipe alround and 20 mm dia pipe @ 150 mm c/c (16 swg) along the length of the unit welded to uprights at 150 mm from FFL DRIP TRAY: independent below the burner in 18SWG Stainless Steel AISI 304 Grade Sheet. UPRIGHTS in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm Angle, 25x3 mm thick Flat in Stainless Steel AISI 202 Grade. PAN SUPPORTS: independent for the burner, 450x450mm Square ring with 8 support flanges both in Cast Iron. BURNERS & FITTINGS: One no. T -35 burner or One no. M - 35 burner, "UNITED" brand or equivalent and the burner provided with Individual Pilot Burner, Needle Control Valve (3/8 BSPTM X 3/8 Cu), Copper Pigtail (Suitable Lenght) internal gas pipeline of 12 mm dia. NB with ERW mildsteel pipe 'C' Class "TATA" or approved make

WORK TABLE WITH SINK Size:1700 x 600 x 850 ht Supply, erection & Commissioning in place of, WORK TABLEWITH SINK on Left hand side , Overall Size:1700 x 600 x 850 ht as below :TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, Sunk in Top with Two sides & Front to be turned down 38 mm and in 12 mm, & Back side 100 mm high back splash.turned back at 90 by 20mm & 12mm, UNDERSHELVES: 1 in No. to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit, The bottom of undershelf shall be provided with one longitudinal and two cross braces with 32x32x3 mm thick stainless steel AISI 202 grade angle for rigigdity. The cross braces shall be welded to uprights. UPRIGHTS in 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick MS Angle below the Top. Sink Bowl: Size- 600x600x300mm deep Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, with all bottom & sides edges rounded at 38mm dia the Bowl Welded to Top securedly with removal of all holes or burr & finished properly to give a uniform look. Provision of 50 mm dia sunk with drain holes at bottom centre of the bowl and stainless steel coupling with gate valve of 50 mm dia. of approved make.

SALAMANDER: Size of 750 X 450 X 400 Interior In 18 Swg S.S. Sheet Exterior In 18 Swg S.S. Sheet Glass wool Insulation S.S. Wire Shelf With Insulated Handles 16 Swg Thick S.S. U Channels For 3 Positions Of S.S. Wire Tray 3 Nos. U Shaped Air Type Heating Elements Kaycee Make Rotary Switch. Indication Lights Teflon Insulated Wiring 3 Core Main Lead (Without Socket) Recessed Controls Electric Salamander Interior In 18 Swg S.S. Sheet Exterior In 18 Swg S.S. Sheet Glass wool Insulation S.S. Wire Shelf With Insulated Handles 16 Swg Thick S.S. U Channels For 3 Positions Of S.S. Wire Tray 3 Nos. U Shaped Air Type Heating Elements Kaycee Make Rotary Switch. Indication Lights Teflon Insulated Wiring 3 Core Main Lead (Without Socket) Recessed Controls

ELECTRICAL HOT BAIN MARIE Size: 1500X700X850mm ht. Supply, erection & Commissioning in place of, ELECTRICAL HOT BAIN MARIE Overall Size: 1500X700X850mm ht. TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304 Grade Sheet, All sides to be turned down 38 mm and in 12 mm. Bain Marie Tank Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet with 12mm water inlet & outlet. UNDERSHELVES: 1 in No.full length and full width to be Fabricated from 18SWG Stainless Steel AISI 304 Grade Sheet, All three sides covered and to be turned down 38 mm and in 12 mm. Welded at 150mm from Bottom of Unit,,The bottom of the undershelf shall be provided with one longitudinal and two cross braces with 32x32X3 MS Angle for rigidity.The cross braces shall be welded to uprights n 38 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. INTERNAL FRAMEWORK in 32x32X3mm thick MS Angle below the Top. Tray Rail 300 mm wide Fabricated from 25x25 mm square tubes of 18SWG Stainless Steel AISI 304 Grade spaced at 75 mm c/c mounted on 25x25 mm 16 swg Stainless Steel Brackets provided at 500 mm c/c. Side Cladding from 18SWG Stainless Steel AISI 304 Grade Sheet. Four nos. 1/1x 150 mm deep GN Pans with acrylic lids for Bain Marie.GN pans shall be 'Anupam' or equivalent make, made of 22 swg stainless steel AISI 304 grade. Two nos Electrical Water immersion heaters of 3KW each at bottom of Bain Marie Tank single phase with individual controls, indicator Lamps & thermostats. The back side of the Bain Marie tank shall be fixed to the unit with SS crews for facilitating.

Gas cylinder manifold The entire material and works required to install and commission a gas cylinder manifold of 4X 2 sets, including but not limiting to following: Main regulator valve – 1 No. Flow control valves at branch points inside kitchen –1 nos. Individual branch control valve – 7 nos. Main pipe line in 1” dia Tata C class seamless pipe – aprox. 100 rft. Branch pipe line in 0.5” dia Tata C class seamless pipe – aprox. 100 rft. Hardware accessories for fixing the manifold and L&T Wall, Pressure Gauge, Surksha Pigtails,a nd pipeline including brackets, threaded rods, Vs make elbow, socket, tee etc., Painting as per standard color code. The contractor will be responsible for obtaining necessary licenses / permissions for the gas cylinder manifold installation. The works shall be carried out as per applicable standards of BIS and OISD. They shall carry out pressure testing and leak testing and issue a fitness certificate. They shall follow the norms of BIS 144 as well as OISD stipulations as applicable. All hardware such as valves shall be of reputed brands like Audco and shall confirm to prescribed safety standards. Scope of this work includes supply, installation, connecting gas supply to all gas fired equipments in the kitchen, testing, commissioning and handing over the gas cylinder manifold in functioning condition.

Vegetable cutter With 5 Blades Motor HP: ½ HP, 1440 rpm Volt: 220 to 240 Volts, Single phase motor Machine RPM: 400 Food grade Material: Special S.S. Steel Blades, Aluminium disc. S.S. Shaft &Polimer Machine suitable for slicing, dicing, grating, Julienne & French fries. Vegetable Output Capacity: 150 to 200 Kg Per Hours.

Potato Peeler 10KG Supply, erection & Commissioning in place of, Potato Peeler 10KG. Peeler Drum Body Fabricated from 16 SWG AISI 304 grade Stainless Steel Sheet.3/4 hp cg make motor.

WATER COOLER, Capacity : 150 Litres per hour Supply, erection & Commissioning in place of, WATER COOLER, Capacity : 150 Litres per hour The Outer Body Fabricated from 21SWG AISI 304 grade Stainless Steel Sheet. The Inner wall of Water Tank fabricated in 22SWG AISI 304 grade Stainless Steel Sheet. UPRIGHTS in 50 mm dia.X 16SWG thick Stainless Steel AISI 304 grade pipe fitted with White Nylon Bullet Leg with 25mm ht. adjustment. Total height 100mm from bottom of Unit. INTERNAL FRAMEWORK in 32x32X3mm thick Stainless Steel AISI 202 Grade Angle below the Top. INSULATION 75mm thk. Polyurethane Foam, COMPRESSOR of suitable Capacity of Standard make. Other Accessories Like Copper Tubing, Circulation Fan, etc. of Standard Quality. Coolant Gas type.The outer and inner wall of Top Door Fabricated from 18SWG AISI 304 grade Stainless Steel Sheet with 40 mm Polyurethane Foam insulation. fitted on Pivotal Hinges with built in Handles & Godrej brand Lock, Door Sealing lining in High Quality Isoprene Rubber. Provision of water inlet, Stainless Steel ball cock, front water collection tray with drain coupling & 2nos stainless steel push type faucets.

GI Exhaust Duct Supply, erection & Commissioning in place of, GI Exhaust Duct fabricated with 0.63 mm gcc sheet.(Approximate 100 sqr/mtr) with 5000 cfm capacity blower exhaust system..

MS GAS STORAGE BANK Supply, erection & Commissioning in place of, MS GAS STORAGE BANK. Capacity 8 cyl. All Frame work Fabricated with 40 x 40 x 6 mm MS Angle and 1.2mm ms sheet.

WET GRINDER 10 LTR Supply, erection & Commissioning in place of, WET GRINDER 10 LTR. capacity electric SS Masala Grinder ( Dosa + Masala ) complete with 20 swg revolving drum , SS pilar , grinding stone with hard coconut scraper suitable capacity electrical motor and gear box with Dol starter control panel complete as required.

PLATE FORM TROLLY Size: 900X600X250 mm ht. Supply, erection & Commissioning in place of, PLATE FORM TROLLY. .Overall Size: 900X600X250 mm ht. Designed for food transfer & handling. Constructed for easy loading & safe mobility.

POT STOVE. Overall Size: 675X675X500mm ht. Supply, erection & Commissioning in place of POT STOVE. Overall Size: 675X675X500mm ht. TOP: of the Table is to be Fabricated from 16SWG Stainless Steel AISI 304T, Side Covering 18 swg 202, MS Welded Angle frame for support. Unit shall be Mounted on 4 nos. of 40 mm SS Pipe legs with adjustable Bullet feet. Pan support of 16" X 16" made of cast iron, Burner - 1 HP Burner. Unit legs shall be cross braced with 25 mm SS Pipe.

SS PALLETS Supply, erection & Commissioning in place of SS PALLETS. Overall Size: 1125X252X200mm ht. Fabricated from 16 swg ss square pipe.