Haryana Urban Development Authority Tender

16.2 + 16.4 Applying pink primer or aluminium priming coat on wood work including preparation of surface knotting & stopping etc with First quality paint. Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete surfaces to give an even shade.

16.18 Painting two coats with ready mixed paint for metallic surfaces in all shades on old steel or iron work. (With first quality paint)

16.48 White washing- Three coats

16.60 Distempering with washable oil bound distemper (of approved manufacture) two coats on old distempered work.

16.62 Finishing walls with exterior decorative cement based paints such as snowcem robbiacem etc. on old work, one coat to give an even shade

17.93 Factory manufacture solid flush door shutter with black board core as per I.S. No 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot pressed, conforming to I.S. 2202 Part-I and II, fixed in position including iron hinges, screws, chocks/cleats and stops etc. (excluding the cost of any fitting other than specified above but including labour for fixing the same in position (I.S.I) Commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges:- 30 mm thick

18.12 Wrought iron & mild steel (using angles, flats square bars tees & channels ladders grills, grating/frames, window guards iron doors open able or fixed stair case or parapet or any other type of railing gates guards etc. including cost of screws & welding roads or bolts & nuts complete fixed in position.)

18.30 Supplying and fixing glass panes including special metal sash putty of approved make. Glass panes 4 mm thick exceeding 40 sq dm areas.

18.34 Pressed steel sheet framed (chowkhats), consisting of 2 mm thick steel sheet of the specified section, including iron lugs (hold fasts), iron hinges, conforming to P.W.D. specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts and finished with one coat of ready mixed paint red lead non-setting primer, of approved quality, fixed in potision including the cost of cement concrete 1:3:6 for filling in the frame and cement concrete 1:3:6 for lugs complete. Door and window frame of size 89 mm x 50 mm with 40 mm wide single rebate.

30.1 Providing and fixing in position best Indian make (to the approval of the Engineer-in-charge) Indian type water closet suite consisting of :- Closet set Vitreous chinaware W.C. pan with horizontal inlet, for sinking into floor with a pair of footrests, 100 mm H.C.I. ‘P’ trap with or without vent as required and suitable joint for closet inlet. 12½ liters capacity mosquito proof cast iron flushing cistern best Indian make I.S.I. marked nomos or other (as approved by the Engineer-in-charge) painted with non-yellowing white or other approved shade enamel paint on outside and black bitumastic superior paint of approved manufacture on inside complete with all accessories such as 20mm G.I. over flow pipe with specials & clamps upto 15cm above floor level of W.C. room and brass perforated mosquito proof cap, 32mm outlet, 15mm I.S.I. marked ballcock, G.I. pull and chain R.S. or C.I. painted brackets and mosquito proof couplings for outlet and overflow pipes, etc. 32 mm diameter telescopic 1.25 mm thick galvanized inside and outside steel flush pipe with clips Complete in all respects including cutting and making good the walls and floors and painting of fittings etc. Size 580mm White PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of the Engineer in-charge) including china plug for tap hole where necessary ; R.S. or C.I. BRACKETS for building into wall including painting; 32mm C.P. BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P. BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and making good the walls, floors and painting of fittings etc. White Size 450mm x 300 mm with one No. tap.

30.41 PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (ORDINARY) LAVATORY SUITES consisting of Lavatory in VITREOUS CHINAWARE size as give below ( to the approval of the Engineer in-charge) including china plug for tap hole where necessary ; R.S. or C.I. BRACKETS for building into wall including painting; 32mm C.P. BRASS WASTE WITH C.P. brass chain and rubber plug; 15mm C.P. BRASS SCREW DOWN PILLAR TAP WITH jam nuts or couplings best design (as approved by the Engineer-in-charge) ALL FITTINGS BEST INDIAN MAKE and; to the approval of the Engineer-in-charge. ALL brass work chromium plated and COMPLETE in all respects INCLUDING cutting and making good the walls, floors and painting of fittings etc. White Size 450mm x 300 mm with one No. tap.

30.75 Providing and fixing in position 15mm i/d C.P. brass bib cock of best quality (as required by the Engineer-in-Charge) Bib cock long body