Haryana Urban Development Authority Tender

[23.22.1.3]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.3. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. TRIPLE POLE MCCB 16 to 100 Amp, 25 KA

[23.27.2]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof . The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 2. M.S. pedestal of size 750 mm wide , 900 mm high , 300 mm deep and bottom totally open , duly embeded in cement concrete block of size 900 mm x 450 mm x 200 mm above ground level , having a base of size 1050 mm x 600 mm x 250 mm below ground level . 0 0

[24.1.1]EARTHING AND LIGHTENING ARRESTOR 1. Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required.

[24.1.2]EARTHING AND LIGHTENING ARRESTOR 2. Extra for using salt and char coal/coke for pipe earth electrode as required.

[24.1.3]EARTHING AND LIGHTENING ARRESTOR 3. Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required.

[24.1.8]EARTHING AND LIGHTENING ARRESTOR 8. Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc. as required with all labour and material.

[24.13.32]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 32. 25 Sq mm 4 core (Arm.)

[24.13.82]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE LOOSE IN EXISTING PIPE OR TRENCHES COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 82. 185 Sq mm 3.5 core (Arm.)

[24.14.56]LT CABLES (Aluminium Conductor, Armoured and Unarmoured) PROVIDING& ERECTION/ LAYING OF PVC/ XLPE INSULATED UNDERGROUND ALUMINIUM CONDUCTOR UNDERGROUND CABLE ONSURFACE/ EXISTING CABLE TRAY COMPLETE IN ALL RESPECT WITH NECESSARY CONNECTION UPTO THE ENTIRE SATISFACTION OF ENGINEER IN CHARGE OF THE WORK 56. 70 Sq mm 4 core (Arm.)

[24.16.3]HT CABLES (Aluminium Conductor, Armoured and Unarmoured) Providing and erection/ laying of XLPE (E) 11 KV HT Aluminium Conductor Armoured Cable ISI Mark Laid in Existing Pipe/Trenches/Surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-In-Charge of the Works 3. Providing and erection/ laying of XLPE (E) 11 KV HT Aluminium Conductor Armoured Cable ISI Mark Laid in Existing Pipe/Trenches/Surface with all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-In-Charge of the Works 70 Sq mm 3 core

[24.2.7.5]LT CABLE 7.5. Supply and erection of suitable compression type brass cable glands for underground Cable :- 120 sqmm to 185 sqmm Cable 3 to 32 Core

[24.3.4.1]HT CABLE 4.1. Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :70 to 120 sqmm

[24.4.3]STREET LIGHT 3. Supply and erection of 32mm dia metre 1.5 m long bracket (B-class) making an angle of 10° to 15° with horizontal plane for mounting street light fitting fixing of GI. bracket on wall with 2 nos. 32 mm x 3 mm thick M.S. clamps including cost of cutting, welding of G.I. pipe complete with cement sand mixture, bolts and nuts etc. including necessary connections.

[24.4.8.7]STREET LIGHT 8.7. Supply and erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with base plate including cost of nut and bolts , earthing studs, Integral Cable termination arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four way connector 2 no 10 A SP MCB , end cover and all accessories as supplied by the manufacture including Providing RCC foundation of M25 grade (1 Cement:1 Stone aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1:5:10 of required dimensions for octagonal poles of various heights as per following specifications complete in all respects and as per directions of Engineer-in-charge 9 Metre Long pole with top dia 100 mm and bottom 200 mm with base plate of size 350 x 350 x 20 mm.

[24.5.1.1]MISCELLANEOUS ITEMS 1.1. Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire satisfaction of Engineer- in-Charge. Submersible Copper Cable 3 Core 1.5 sqmm

[24.5.2.5]MISCELLANEOUS ITEMS 2.5. S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre below ground level including digging and refilling of earth including cost of suitable size socket/coupler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 120/105 mm outer dia/ inner dia

Supply and Erection of Sensor based AMSON’s/ Indo Asian make automatic Electronic timer to Switch ON/OFF the street / Road light automatically. It will change switching ON/OFF timings automatically on daily basis throughout the year as per change in timing of sun rising and sun setting suitable for street/ Road lights. It will have three contractors of 24 Volt of BCH (Bhartiya Cutler Hammer) to control load upto 40 Amp. Per phase with voltage ratio @230/240. It will have light activated automatic Switching system to switch ON/OFF of the Road street lights. It will have Auto/ manual systems for maintenance of street light during day time. It should have Transformers with voltage ratio 230/240 and other allied accessories as required. Bakelite sheet to assemble the components etc. It should have Kit Kat of 20 Amps capacity to save the time switch from power fluctuation. The device will be housed in the existing pedestal/box/pole etc. in such a way so that it operates at correct timings and erection of the same at site complete in all respect upto the entire satisfaction of Engineer-In-Charge.

Supply, Erection and Transportation upto site including all taxes as per latest Govt. Instruction amended time again of Prestressed cement concrete pole as per IS: 1678/1960. 11 Mtr. Long 140mm x 200mm at top and 140mm x 400mm at bottom with working load of 400 kg. Buried 2.20 m in ground or as per UHBVNL specification complete in all respect up to the entire satisfaction of Engineer-in-Charge.

Supply and erection of 11 KV Lightening Arrestor (conforming to ISS:3070/1985) with latest amendments complete in respect and erection of the same upto the entire satisfaction of the Engineer-in-charge.

Supply and Erection of fuse unit L.T. side of 100/200 KVA Transformer complete with wooden board cleats, aluminium strips M.S. clamp and M.S. Nuts and Bolts including all petty material required upto the entire satisfaction of Engineer-In-Charge.

S/E of 11 KV disc fitting (Hardware) with accessories suitable for stringing and sagging of ACSR Conductor 50 Sqmm. Conforming to relevant IS specification with latest amendments complete in all respect upto the entire satisfaction of Engineer-In-Charge.

S/E of Disc Insulator without fitting T and C Type Jay Shree Make (Conforming to ISS:2486 Part-I and II) with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge.

S/E of 11 KV G.I. Pins (long) for H.T. line (Conforming to ISS 2486 (Part-I and II) with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge.

S/E of 11 KV Pin Insulator Brown Glazed with creepage distance with 230mm Jaya Shree Make (Conforming to ISS 73/1971) with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge.

S/E of G.I Pipe earthing set 40mm dia 2.5 Mtr. long shall be of medium class conforming to ISS: 1239(Part-I) with latest endments shall have 12mm dia holes at interval of 150mm on the entire surface of the earthing pipe shall be tapered and top and of G.I pipe shall be threaded and shall be provided with suitable size of G.I earth wire. The clamp shall be tightened to the earth pipe with 12mm dia galvanized M.S. Nut and Bolts and spring washers complete in all respect upto entire satisfaction of Engineer-In-charge.

Supply and erection of Earthing Rod of 20mm dia and 2.5 Mtr. Long shall be tapered to be pointed at one end of about length of 50mm and other end of the rod shall flatten over a length of 150mm into 40mm and having two holes of 12mm dia and 50mm apart alongwith 16 SWG thick conduit pipe 25mm dia 3 Mtr. Long (conforming to IS 9537 (Part-I) enameled black painted complete in all respect upto the entire satisfaction of Engineer-In-Charge.

S/E of G.S.L. wire 8 SWG conforming to ISS: 280/1978/1963 with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-charge.

Supply and erection of G.O. Switches with 9 Nos. Post Insulators of Jay Shree Make Conforming to ISS:1818/1972 and ISS:2544/1963 with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge.

Supply and Erection of Three Phase 11 KV/ 0.433 KV-250 V, 200 KVA Oil immersed, naturally cooled, Aluminum Wound Outdoor type Distribution Transformers with CSP (Completely self protected) features with external microprocessor based MCCB, strictly conforming to Nigam’s technical specification No. CSC-V/R-I/DH/UH/P and D/2010-2011 read with amendment thereof and as per relevant ISS as amended from time to time and losses confirming to 4 Star rating of BEE as per Appd. make and Specification of DHBVN/ UHBVN including making of plateform and installation of transformer upto the entire satisfaction of Engineer-in-Charge. (with 6 years defect liability period, free of cost) Voltage Rated Frequency permitted at 75o C i) Maximum load losses at 50% load at 75o C = 780 watt ii) Maximum losses at 100% load at 75o C = 2300 watt iii) Warranty = 78/72 Months. The above losses are maximum allowable and these would not be any positive tolerance.

S/E and Erection of ACSR Cond. (confirming to IS 398(PART-II)-1976 -1996,4826-1976 , IS: 1521-1972 and IS:1778-1980 with latest amendments and the erection of the same with accessories including stringing and sagging of conductor as well as jointing and binding with insulator at spots complete in all respect up to the entire satisfaction of the engineer –in - charge. ACSR Conductor 80 Sqmm

S/E of Guard made of G.S.L. Wire 8 SWG Conforming to ISS:280/1978/1963 with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge for H.T. Line.

Supply and Fabrication of M.S. Channel size 100x50x6mm M.S. Channel size 75x40x6mm as per relevant IS specification, painting and priming coat upto the entire satisfaction of Engineer-in-Charge.

Supply and Fabrication of M.S. Angle Iron size 50x50x6mm as per relevant IS specification alongwith painting, priming coat upto the entire satisfaction of Engineer-in-Charge.

Supply and Fabrication of M.S. Flat size 50x6mm as per relevant IS specification alongwith painting and priming coat upto the entire satisfaction of Engineer-in-Charge.

Supply and Erection of 300 Sqmm single core un-armoured power cable with aluminum conductor 650/1100 V confirming to ISS 1554(Part-I) of 1988 IS 7098/Part-I/1988 with latest amendments upto respect upto the entire satisfaction of Engineer-In-Charge. Make (Plaza/ICL/KEI/UNIVERSAL/CIRTINA/Grandlay).

Supply and erection of LED Flood light Luminaires 200 Watt with high power LED street light in aluminium PDC housing, toughened glass cover with IP 66 protection complete assembly with LED driver and accessories required to complete the job in all respect including erection and fixing including connection and other petty material for the same upto the entire satisfaction of Engineer-in-Charges of the work. (Warranty- 3 Years Including Driver against any manufacturing defect) (Including Three Years Free Mtc./Defect Liability Period Free Of Cost). The logo of company should be embossed on the fixture. (Make:- Phillip's/Bajaj/LT/Panasonic Anchor)

Supply and erection of 100 KVA outdoor type non sealed 3 phase 50 HZ 11/0.433/100 KVA Aluminum wound oil immersed naturally cooled distribution transformer complete with fitting and accessories inclusive of Ist filling of oil and confirming to ISS 2026/1977 with latest amendments complete in all respect and similarity of transformer should have been got type tested including making of plate form and installation of transformer specification of DHSBVN /UHBVN upto the entire satisfaction of Engineer-in-Charge. Voltage Rated Frequency permitted at 75 ‘ C i) No Load losses (Max) = 220 watt ii) Full Load losses (Max) = 1760 watt The above losses are maximum allowable and these would not be any positive tolerance. (4 star rating)

Supply, Installation Testing and Commissioning of LED Street Light Fixture with Wattage range of (72 Watt) with body made of Pressure Die Cast Aluminum Alloy and cover made of PMMA (polymethymethacrylate) having system Lumen)120Ipw with inbuilt Protection against Short Circuit, Miswiring, Over Voltage and Surage Protection of 6 KV. The IP of Driver Comparment should not be less than IP66 and same for the LED Comparment. The driving current should be ( 700mA with THD ( 5% and PF ). 95 and Operating Voltage between 100-270V and CRI ) 72 and Impact Resistance of IK 08. The specifications as mentioned above should be duly tested and Mentioned in LM79 Report from Govt. Approved NABL Accredited Labrotary and LM80 Report of LED Chip from the Manufacturer to complete the job in all respect including erection on existing pole for fixing including connection of the same upto the entire satisfaction of Engineer-in-Charges of the work. (Warranty- 3 Years replacement warranty Including Driver against any manufacturing defect) (Including Three Years Free replacement warranty Mtc./Defect Liability Period Free Of Cost). The logo of company should be embossed on the fixture. (Makes of Phillip’s/Bajaj/LT/Panasonic Anchor).

Providing and Fixing of round detachable for fixing of flood light made out of 50 mm dia G.I. pipe including 2 Nos. by support of G.I. pipe 50 mm dia and pole 0.40 Mtr. long M.S. Sleeve of 100 mm dia including 50 x 6 mm Flat for fixing of gear box etc. complete in all respect up to the entire satisfaction of Engineer-In-Charge.

HT METERING PANEL Supply and erection, testing and commissioning of cubical type dust and vermont proof metering panel standing floor mouting sutable for 11 KV 3 Phase supply made out of 14 gauage M.S. sheet with channel iron base frame painted with stroving synthetic light grey enameld paint ssutable for operation on 11 KV 3 phase for wire 50 Cycle effectively earthed system and commissioning of th following. Cubical boxes of min. size 700 X 500 as per approved by UHBVNL of 14 SWG M.S. sheet with double door opening 1 For energy meter and another for CT and PT with 11 KV resin cast bushing. 3 Nos. 11 KV CT of capacity 50/5 amp 10 VA burden 0.5 class accuracy suitable for indoor installation of approved make by UHBVNL. 1 No. PT 11 KV 11000/110 V 3 phase oil filled /cooled 10 VA class accuracy 0.5 suitable for indoor indoor installation of approved make by UHBVNL. 2 Nos. side cable termination end boxes heat shrinkable type for incoming andout going 11 KV XLPE cable of size 185 SQmm X 3 Core. Electronic tri vector meter 11 KV HT 50 % class accuracy 0.5 11 KV / 110 V for reading in KWH approved make by UHBVNL ISI mark. The panel will be completed with all internal wiring interconnection VT and HT compound filling of cable end boxes. HT cable connection etc. complete in all respect with guaranty for 12 Months including its testing and approved of all items by UHBVNL authoriyy including the cost of CT PT, TTB electronic meter and other equipment by UHBVNL authorities upto the entire satisfaction of the engineer in charge of the work.

Supply/Erection/ /Testing and Commissioning of Distribution Panel for Power and Light.and fixing of dust vermin proof,gasket nut MCCB/MCB and Vice Versa Power Coated bolts, hinges etc. enclosure made of CRCA shect Processed Power Coated, having 1.6mm thick load bearing surface, duly 9Tank aluminum Bus bar, compartment type Panel Board with Powder coated siemes grey colour with support PVC Sleeve, hardware and control wiring etc. I No. MCCB 400 Amp. 4 Pole with Rotary Handle and Copper Spreder Link I Set Bus Bar 400 Amp. 3 Phase 4 wire 4 Nos. MCCB 250 Amp. with Rotary Handle and Copper Spreder 1ink 2 Nos. MCCB 100 Amp. with Rotary Handle and Copper Spreder Lmk. 3 Nos. CT 400/5 Amp. Metering of Volte Meter, Amp. Meter, Indicator 16mm wire from Bus Bar to Thimbles with

Supply/Erection/Testing and Commissioning of Capacitor Panel 70 KVAR with MCCB 160A 3P 25KA, Spreader Link, Ext. Rotatary Handle of MCCB, MCB TP 20A, MCB TP 32A, MCB TP 40A, MCB SP 6A Cap duty contractor 5 KVAR, 10KVAR and 15 KVAR, Capacitor Bank 5 KVAR, 10 KVAR and 15 KVAR, APFCR Relay 6 Steps, Indicating light Red, Auto/Manual Selector switch and CT 250/5 and Fabrication in 1.6mm/2mm CRCA sheet powder coating in seimens grey shade, Lock, Gasket, Rubber, Hardware etc. Busbar and Hardware, Wiring and accessories complete in all respect up to entire satisfaction of the Engineer-in-Charge.

Supply/Erection/Testing and Commissioning of Main LT Panel with Main incoming Outgoing, Metering, Fabrication and Busbar and Hardware, wiring and accessories complete in all respect with following accessories :- Main Incoming • MCCB 400A 4P • Spreader Link • Ext. Rotatary Handle • COS 400A Outgoing • MCCB 4P 250A • Spreader Link • MCCB 4P 160A • Spreader Link • MCCB 4P 100A • MCB TPN 63A Metering • Volt plus Amp. Meter plus SP MCB 3-3 No. plus CT- 3 Nos. plus CT-T.B-4 No. plus Indicating Lamp. Fabrication Section • Fabrication in 1.6mm/2mm CRCA Sheet Powder Coating in Siemens Grey Shade. Lock, Gasket, Rubber, Hardware etc. Busbar and Hardware, Wiring and Accessories • Aluminium Main Busbar, load wise Sub feeder busbar Colour coated Heat Shrink busbar sleeve nut-bolt, washer, hardware etc. • Power and control wiring will be (ISI 1100V) Flamac smoke FRLS PVC Single core copper wire, copper lugs, PVC Sleeves Ferruels numbers Hardware and labour etc. complete in all respect up to entire satisfaction of the Engineer-in-Charge.